Performance of human body communication-based wearable ECG with capacitive coupling electrodes

Novel Stable Capacitive Electrocardiogram Measurement System

This study presents a noncontact electrocardiogram (ECG) measurement system to replace conventional ECG electrode pads during ECG measurement. The proposed noncontact electrode design comprises a surface guard ring, the optimal input resistance, a ground guard ring, and an optimal voltage divider feedback. The surface and ground guard rings are used to reduce environmental noise. The optimal input resistor mitigates distortion caused by the input bias current, and the optimal voltage divider feedback increases the gain. Simulated gain analysis was subsequently performed to determine the most suitable parameters for the design, and the system was combined with a capacitive driven right leg circuit to reduce common-mode interference. The present study simulated actual environments in which interference is present in capacitive ECG signal measurement. Both in the case of environmental interference and motion artifact interference, relative to capacitive ECG electrodes, the proposed electrodes measured ECG signals with greater stability. In terms of R-R intervals, the measured ECG signals exhibited a 98.6% similarity to ECGs measured using contact ECG systems. The proposed noncontact ECG measurement system based on capacitive sensing is applicable for use in everyday life.

Non-Contact Heart-Rate Measurement Method Using Both Transmitted Wave Extraction and Wavelet Transform

Continuous monitoring of heart-rate is expected to lead to early detection of physical discomfort. In this study, we propose a non-contact heart-rate measurement method which can be used in an environment such as driver heart-rate monitoring with body movement. The method is based on the electric field strength transmitted through the human body that changes with the diastole and systole of the heart. Unlike conventional displacement detection of the skin surface, we attempted to capture changes in the internal structure of the human body by irradiating the human body with microwaves and acquiring microwaves that pass through the heart. We first estimated the electric field strength transmitted through the heart using three receiving sensors to reduce the body movement effect. Then we decomposed the estimated transmitted electric field using stationary wavelet transform to eliminate significant distortion due to body movement. As a result, we achieved an estimation accuracy of heart-rate as high as 98% in a verification experiment with normal body movement.

Blood pressure estimation system using human body communication-based electrocardiograph and photoplethysmography

In order to realise low-load cuffless and continuous blood pressure measurement in daily life, the authors developed a blood pressure estimation system combining human body communication-based wearable electrocardiograph and reflectance photoplethysmography. The principle is based on a relationship between the pulse arrive time and the systolic blood pressure. The pulse arrive time is the time period between the R-wave in electrocardiograph and peak of pulse wave. The greatest feature is the use of a human body communication-based electrocardiograph which can provide automatic synchronisation in time between the measured electrocardiograph and pulse wave signals to obtain the pulse arrive time so that no additional synchronisation circuit is required. Using this system, the authors measured the pulse arrive time from the electrocardiograph and pulse wave signals in real time, estimated the systolic blood pressure and compared the result with that measured by a cuff sphygmomanometer. The authors found that the root mean square error of the estimated blood pressure and the actual value measured using the cuff sphygmomanometer was 4.5 mmHg or less, and the correlation coefficient was >0.6 with a P value much <0.05. These results show the validity of the developed system for cuffless and continuous blood pressure estimation.

ImpediBands: Body Coupled Bio-Impedance Patches for Physiological Sensing Proof of Concept

Continuous and robust monitoring of physiological signals is essential in improving the diagnosis and management of cardiovascular and respiratory diseases. The state-of-the-art systems for monitoring vital signs such as heart rate, heart rate variability, respiration rate, and other hemodynamic and respiratory parameters use often bulky and obtrusive systems or depend on wearables with limited sensing methods based on repetitive properties of the signals rather than the morphology. Moreover, multiple devices and modalities are typically needed for capturing various vital signs simultaneously. In this paper, we introduce ImpediBands: small-sized distributed smart bio-impedance (Bio-Z) patches, where the communication between the patches is established through the human body, eliminating the need for electrical wires that would create a common potential point between sensors. We use ImpediBands to collect instantaneous measurements from multiple locations over the chest at the same time. We propose a blind source separation (BSS) technique based on the second-order blind identification (SOBI) followed by signal reconstruction to extract heart and lung activities from the Bio-Z signals. Using the separated source signals, we demonstrate the performance of our system via providing strong confidence in the estimation of heart and respiration rates with low RMSE (HR_RMSE = 0.579 beats per minute, RR_RMSE = 0.285 breaths per minute), and high correlation coefficients (r_HR = 0.948, r_RR = 0.921).

Convolutional Neural Network Based Detection of Atrial Fibrillation Combing R-R intervals and F-wave Frequency Spectrum

Atrial Fibrillation (AF) is one of the arrhythmias that is common and serious in clinic. In this study, a novel method of AF classification with a convolutional neural network (CNN) was proposed, and particularly two cardiac rhythm features of R-R intervals and F-wave frequency spectrum were combined into the CNN for a good applicability of mobile application. Over 23 patients' ten-hours of Electrocardiogram (ECG) records were collected from the MIT-BIH database, and each of which was segmented into 10s-data fragments to train the designed CNN and evaluate the performance of the proposed method. Specifically, a total of 83,461 fragments were collected, 49,952 fragments of which are the normal fragments (type-N) and the others are the AF fragments. As results, the obtained average accuracy of the proposed method combining the two proposed features is 97.3%, which is shown a relative higher accuracy comparing with either that of the detection with the feature of R-R intervals (95.7%) or that with the feature of F-wave frequency spectrum (93.9%). Additionally, the sensitivity and the specificity of the present method are both of a high level of 97.4% and 97.2%, respectively. In conclusion, the CNN based approach by combining the R-R interval series and the F-wave frequency spectrum would be effectively to improve the performance of AF detection. Moreover, the proposed classification of AF with 10s-data fragments also could be potentially useful for a wearable real-time monitoring application for a pre-hospital screening of AF.

Noise-Resistant CECG Using Novel Capacitive Electrodes

For years, capacitive electrocardiogram (CECG) has been known to be susceptible to ambient interference. In light of this, a novel capacitive electrode was developed as an effective way to reduce the interference effect. This was done by simply introducing the capacitive elector in series with a 1 pF capacitor, and the 60 Hz common mode noise induced by AC power lines was cancelled using a capacitive right leg (CRL) circuit. The proposed electrode did as expected outperform two counterparts in terms of SNR, and particularly gave an up to 99.8% correlation between RRIs extracted from an ECG and a CECG signal, a figure far beyond 52% and 63% using the two counterparts. This capacitive electrode was originally designed for long-term noncontact monitoring of heart rate, and hopefully can be integrated to portable devices for other medical care services in the near future.

An Embedded, Eight Channel, Noise Canceling, Wireless, Wearable sEMG Data Acquisition System With Adaptive Muscle Contraction Detection

Wearable technology has gained increasing popularity in the applications of healthcare, sports science, and biomedical engineering in recent years. Because of its convenient nature, the wearable technology is particularly useful in the acquisition of the physiological signals. Specifically, the (surface electromyography) sEMG systems, which measure the muscle activation potentials, greatly benefit from this technology in both clinical and industrial applications. However, the current wearable sEMG systems have several drawbacks including inefficient noise cancellation, insufficient measurement quality, and difficult integration to customized applications. Additionally, none of these sEMG data acquisition systems can detect sEMG signals (i.e., contractions), which provides a valuable environment for further studies such as human machine interaction, gesture recognition, and fatigue tracking. To this end, we introduce an embedded, eight channel, noise canceling, wireless, wearable sEMG data acquisition system with adaptive muscle contraction detection. Our design consists of two stages, which are the sEMG sensors and the multichannel data acquisition unit. For the first stage, we propose a low cost, dry, and active sEMG sensor that captures the muscle activation potentials, a data acquisition unit that evaluates these captured multichannel sEMG signals and transmits them to a user interface. In the data acquisition unit, the sEMG signals are processed through embedded, adaptive methods in order to reject the power line noise and detect the muscle contractions. Through extensive experiments, we demonstrate that our sEMG sensor outperforms a widely used commercially available product and our data acquisition system achieves 4.583 dB SNR gain with accuracy in the detection of the contractions.

Motion artefact removals for wearable ECG using stationary wavelet transform

Wearable Electrocardiogram (ECG) is attracting much attention in daily healthcare applications. From the viewpoint of long-term use, it is desired that the electrodes are non-contact with the human body. In this study, the authors propose an algorithm using the stationary wavelet transform (SWT) to remove motion artefact superimposed on ECG signal when using non-contact capacitively coupling electrodes. The authors evaluate the effect on motion artefact removal of this algorithm by applying it to various ECG signals with motion artefacts superimposed. As a result, the correlation coefficients of ECG signals with respect to the clean ones have been improved from 0.71 to 0.88 on median before and after motion artefact removal, which demonstrates the validity of the proposed SWT-based algorithm.