Study of Radio Frequency Plasma Treatment of PVDF Film Using Ar, O₂ and (Ar + O₂) Gases for Improved Polypyrrole Adhesion

Improvement of the binding of polypyrrole with PVDF (polyvinylidene fluoride) thin film using low pressure plasma was studied. The effects of various plasma gases i.e., Ar, O₂ and Ar + O₂ gases on surface roughness, surface chemistry and hydrophilicity were noted. The topographical change of the PVDF film was observed by means of scanning electron microscopy and chemical changes by X-ray photoelectron spectroscopy, with adhesion of polypyrrole (PPy) by abrasion tests and sheet resistance measurements. Results showed that the increase in roughness and surface functionalization by oxygen functional groups contributed to improved adhesion and Ar + O₂ plasma gave better adhesion.

Controlled oxidation, biofunctionalization, and patterning of alkyl monolayers on silicon and silicon nitride surfaces using plasma treatment

A new method is presented for the fast and reproducible functionalization of silicon and silicon nitride surfaces coated with covalently attached alkyl monolayers. After formation of a methyl-terminated 1-hexadecyl monolayer on H-terminated Si(100) and Si(111) surfaces, short plasma treatments (1-3 s) are sufficient to create oxidized functionalities without damaging the underlying oxide-free silicon. The new functional groups can, e.g., be derivatized using the reaction of surface aldehyde groups with primary amines to form imine bonds. In this way, plasma-treated monolayers on silicon or silicon nitride surfaces were successfully coated with nanoparticles, or proteins such as avidin. In addition, we demonstrate the possibility of micropatterning, using a soft contact mask during the plasma treatment. Using water contact angle measurements, ellipsometry, XPS, IRRAS, AFM, and reflectometry, proof of principle is demonstrated of a yet unexplored way to form patterned alkyl monolayers on oxide-free silicon surfaces.

Atomic oxygen reactions with semifluorinated and n-alkanethiolate self-assembled monolayers

The interaction of atomic oxygen (O(3P)) with semifluorinated self-assembled monolayers (CF-SAMs), two different n-alkanethiolate self-assembled monolayers, and a carbonaceous overlayer derived from an x-ray modified n-alkanethiolate SAM have been studied using in situ x-ray photoelectron spectroscopy. For short atomic oxygen exposures, CF-SAMs remain intact, an effect ascribed to the inertness of C-F and C-C bonds toward atomic oxygen and the well-ordered structure of the CF-SAMs. Following this initial induction period, atomic oxygen permeates through the CF3(CF2)7 overlayer and initiates reactions at the film/substrate interface, evidenced by the formation of sulfonate (RSO3) species and Au2O3. These reactions lead to the desorption of intact adsorbate chains, evidenced by the loss of carbon and fluorine from the film while the C(1s) spectral envelope and the C(1s)/F(1s) ratio remain virtually constant. In contrast, the reactivity of atomic oxygen with alkanethiolate SAMs is initiated at the vacuum/film interface, producing oxygen-containing carbon functional groups. Subsequent reactions of these new species with atomic oxygen lead to erosion of the hydrocarbon film. Experiments on the different hydrocarbon-based films reveal that the atomic oxygen-induced kinetics are influenced by the thickness as well as the structural and chemical characteristics of the hydrocarbon overlayer. Results from this investigation are also discussed in the context of material erosion by AO in low Earth orbit.

Recycled wool-based nonwoven material as an oil sorbent

The aim of this study was to highlight the possibility of using recycled wool-based nonwoven material as a sorbent in an oil spill cleanup. This material sorbed higher amounts of base oil SN 150 than diesel or crude oil from the surface of a demineralized or artificial seawater bath. Superficial modification of material with the biopolymer chitosan and low-temperature air plasma led to a slight decrease of sorption capacity. Loose fibers of the same origin as nonwoven material have significantly higher sorption capacities than investigated nonwoven material. White light scanning interferometry analysis of the fibers suggested that roughness of the wool fiber surface has an important role in oil sorption. The laboratory experiments demonstrated that this material is reusable. Recycled wool-based nonwoven material showed good sorption properties and adequate reusability, indicating that a material based on natural fibers could be a viable alternative to commercially available synthetic materials that have poor biodegradability.