Cyclic stress fields for fatigue cracks in amorphous solids Experimental measurements and their implications

Characteristics of Crack Growth in Rock-Like Materials under Monotonic and Cyclic Loading Conditions

Experiments with gypsum as a model rock material were conducted to investigate the characteristics of crack growth under monotonic and cyclic loading. The specimens had two pre-existing flaws that were placed at different inclination angle, spacing and continuity. Tensile or wing cracks and secondary or shear cracks were observed in both the monotonic and cyclic tests. Wing cracks or tensile cracks initiated at (or near) the tips of flaws and grew parallel to the loading direction. Secondary or shear cracks occurred after initiation of the wing crack and culminated in a final failure. Secondary cracks started at the tips of flaws and propagated in the colinear direction of flaws or perpendicular to loading. Six types of coalescence were observed. Both the monotonic and cyclic tests showed almost identical coalescence types. Coalescence occurred due to the internal shear cracks in specimens containing colinear flaws, while it occurred through combinations of internal shear cracks, internal wing cracks and tension cracks in specimens with non-colinear flaws. Fatigue cracks occurred in tests under cyclic loads. Finally, the subcritical crack growth parameters under monotonic and cyclic loading were determined. Although there were variations in the parameters, the parameter “n” showed similar values.

Study of fatigue resistance of chemical and radiation crosslinked medical grade ultrahigh molecular weight polyethylene

The aim of this work is to understand the role of chemical and radiation induced crosslinking on the fatigue crack propagation resistance of medical grade ultrahigh molecular weight polyethylene (UHMWPE). In recent years, the need to improve the tribological performance of UHMWPE used in total joint replacements has resulted in the widespread utilization of crosslinking as a method to improve wear resistance. Although crosslinking has been shown to drastically improve the wear resistance of the polymer, the potential trade-off in fatigue properties has yet to be addressed. Fatigue crack propagation resistance is a concern in tibial inserts where large cyclic stresses are sufficient to drive the growth of subsurface cracks that potentially contribute to delamination wear mechanisms. For clinical relevance, the combined effects of sterilization and aging are examined in two commercially available crosslinked resins. Nonsterile and unaged resins serve as a control. To evaluate the effect of crosslinking, a comparison is made to uncrosslinked resins. Scanning electron microscopy is used to provide an understanding of fatigue fracture mechanisms in the crosslinked polymers. The results of this study show that the current level of crosslinking used in orthopedic resins for enhanced wear resistance is not beneficial for fatigue crack propagation resistance.

Comparison of the effects of gamma radiation and low temperature hydrogen peroxide gas plasma sterilization on the molecular structure, fatigue resistance, and wear behavior of UHMWPE

The effects of gamma radiation and low temperature hydrogen peroxide gas plasma (HPGP) sterilization on structure and cyclic mechanical properties were examined for orthopedic grade ultra-high-molecular-weight polyethylene (UHMWPE) and compared to each other as well as to no sterilization (control). Density was monitored with a density gradient column and was found to be directly influenced by the sterilization method employed: Gamma radiation led to an increase, while plasma did not. Oxidation of the polymer was studied by observing changes in the carbonyl peak with Fourier transform infrared spectrometry and was found to be strongly affected by both gamma radiation and subsequent aging, while plasma sterilization had little effect. Gamma radiation resulted in embrittlement of the polymer and a decreased resistance to fatigue crack propagation. This mechanical degradation was a direct consequence of postradiation oxidation and molecular evolution of the polymer and was not observed in the plasma-sterilized polymer. Both gamma radiation and plasma sterilization led to improved wear performance of the UHMWPE compared to the nonsterile control material.

Cyclic compressive loading results in fatigue cracks in ultra high molecular weight polyethylene

Wear damage to the articulating surfaces of total joint components made of ultra high molecular weight polyethylene is associated with a fatigue fracture mechanism, despite the fact that these surfaces are subjected to primarily compressive and compressive-tensile cyclic stresses. The question arises as to whether fatigue cracks will form under such loading conditions. In this study, we experimentally demonstrated that fatigue cracks could be initiated and propagated in notched ultra high molecular weight polyethylene specimens subjected to fully compressive and compressive-tensile cyclic loading. Under these loading conditions, growth of fatigue cracks was limited: the cracks arrested without catastrophic failure of the test specimens. The final length of the crack was dependent on the load ratio of the fatigue cycle; fatigue cracks propagated to greater lengths as the load ratio was increased.