Fabrication of porous poly(epsilon-caprolactone) microparticles for protein release

Disodium norcantharidate loaded poly(ɛ-caprolactone) microspheres

Poly(epsilon-caprolactone) (PCL) microspheres encapsulating disodium norcantharidate (DSNC), a drug in salt form and with high water solubility, were prepared by s/o/w solvent evaporation technique and characterized in terms of size, morphology, encapsulation efficiency and drug release. The viscosity of s/o dispersion was crucial to the successful encapsulation of DSNC. Scanning electron microscopy (SEM) studies showed that the drug-loaded microspheres had coarse surface and porous internal structure. The analysis of X-ray diffraction (XRD) indicated that there was no interaction between DSNC and PCL, but the degree of crystallinity of PCL decreased with the introduction of the drug. The drug release profiles indicated an initial burst release followed by a slow release, and a further investigation into the release mechanism implied that the release of DSNC from PCL microspheres was caused by a combination of diffusion and osmotic pressure.

Microspheres Made of Poly(ɛ-caprolactone)-Based Amphiphilic Copolymers: Potential in Sustained Delivery of Proteins

Microspheres of amphiphilic multi-block poly(ester-ether)s (PEE)s and poly(ester-ether-amide)s (PEEA)s based on poly(epsilon-caprolactone) (PCL) were investigated as delivery systems for proteins. The interest was mainly focused on the effect of their molecular structure and composition on the overall properties of the microspheres, encapsulating bovine serum albumin (BSA) as a model protein. PEEs and PEEAs were prepared using a alpha,omega-dihydroxy-terminated PCL macromer (Mn= 2.0 kDa) as a hydrophobic component. Hydrophilic oxyethylene sequences were generated using poly(ethylene oxide)s (PEO)s of different molecular mass (Mn= 300-600 Da) in the case of PEEs, or 4,7,10-trioxa-1,13-tridecanediamine (Trioxy) and PEO150 (Mn= 150 Da) in the case of PEEAs. The copolymers showed a decrease of Tm and crystallinity values as compared with PCL. Within each class of copolymers, the bulk hydrophilicity increased with increasing the number of oxyethylene groups in the chain repeat unit. PEEAs were more hydrophilic than PEEs with a similar number of oxyethylene groups. Discrete spherical particles were prepared by both PEEs and PEEAs and their BSA encapsulation efficiency related to copolymer properties. Interestingly, the insertion of short hydrophilic segments is enough to significantly affect protein distribution inside microspheres and its release profiles, as compared to PCL microspheres. Different degradation rates and mechanisms were observed for copolymer microspheres, mainly depending on the distribution of oxyethylene units along the chain. The results highlight that a fine control over the structural parameters of amphiphilic PCL-based multi-block copolymers is a key factor for their application in the field of protein delivery.

Poly-epsilon-caprolactone microspheres and nanospheres: an overview

Poly-epsilon-caprolactone (PCL) is a biodegradable, biocompatible and semicrystalline polymer having a very low glass transition temperature. Due to its slow degradation, PCL is ideally suitable for long-term delivery extending over a period of more than one year. This has led to its application in the preparation of different delivery systems in the form of microspheres, nanospheres and implants. Various categories of drugs have been encapsulated in PCL for targeted drug delivery and for controlled drug release. Microspheres of PCL either alone or of PCL copolymers have been prepared to obtain the drug release characteristics. This article reviews the advancements made in PCL-based microspheres and nanospheres with special reference to the method of preparation of these and their suitability in developing effective delivery systems.