Effects of fluid insert volume changes on socket pressures and shear stresses: case studies from two trans-tibial amputee subjects

Assessing Socket Fit Effects on Pressure and Shear at a Transtibial Residuum/Socket Interface

Fluctuations in residuum volume during daily activities are known to occur in lower-limb amputees. This can cause frequent changes to fit, which cannot be accommodated by commonly-used prosthetic sockets. The real-time effects, if any, of these minor socket fit changes on interface biomechanics have not been studied extensively. Amputees commonly use different layers of socks to accommodate frequent volume fluctuations, enabling adjustment of socket fit. We, thus, altered socket fit levels via addition/removal of sock layers to a transtibial amputee who habitually-donned two-sock layers to mimic relatively looser and tighter socket fits. Interface pressure and shear sensors were placed at known prominent load-bearing sites of the transtibial residuum/socket interface, i.e., patellar tendon (PT), popliteal fossa (PF), and anterior-distal (AD) end, to measure real-time biomechanical interactions during standing and level walking. Although socket fit level was only slightly modified, changes in interface pressure and shear across anatomical sites were still observed. Tighter fit corresponds to notable pressure reduction at AD during early stance and pressure increase at PT during terminal stance due to the residuum being pushed up. Shear-to-pressure ratios were used to assess comfort, while pressure- and shear-time integrals were used to assess tissue health. We observed more notable changes at tissue sites (e.g., AD and PF). Combined evaluation of pressure and shear, including shear-to-pressure ratio and time integrals, may offer insight for residuum care.

Advances in the measurement of prosthetic socket interface mechanics: a review of technology, techniques, and a 20-year update

INTRODUCTION

A key determinant of prosthesis use is the quality of fit of the prosthetic socket. The socket surrounds the residual limb and applies the appropriate force distribution to the soft tissues to maintain suspension, support, and stabilization as well as translate limb movement to prosthesis movement. The challenge in socket fabrication lays in achieving geometry that provides the appropriate force distribution at physiologically appropriate locations; a task dependent on the understanding of interface tissue-mechanics.

AREAS COVERED

In the last 20 years substantial advancements in sensor innovation and computational power have allowed researchers to quantify the socket-residual limb interface; this paper reviews prominent measurement and sensing techniques described in literature over this time frame. Advantages and short comings of each technique are discussed with a focus on translation to clinical environments.

EXPERT OPINION

Prosthetic sockets directly influence comfort, device use, user satisfaction, and tissue health. Advancements in instrumentation technology have unlocked the possibility of sophisticated measurement systems providing quantitative data that may work in tandem with a clinician's heuristic expertise during socket fabrication. If validated, many of the emerging sensing technologies could be implemented into a clinical setting to better characterize how patients interact with their device and help inform prosthesis fabrication and assessment techniques.

Measuring discomfort-An objective method for quantifying peak pressure discomfort and improved fit in adults with transtibial amputation

BACKGROUND

Prosthetic socket coupling with the residual limb should be comfortable without causing skin breakdown or excessive pressure. However, users report socket discomfort, and there is a scarcity of objective measurements available to assess this feeling of discomfort. Quantifying the specific pressure may enable clinicians and users to determine and improve comfort levels objectively.

OBJECTIVES

(1) To evaluate if a peak pressure reduction assists in resolving wounds, redness, and pain inside prosthetic sockets in people with transtibial amputation. (2) To determine if peak pressures measured inside the prosthetic socket due to external forces could be used to quantify the level of improvement in socket discomfort.

DESIGN

In this cohort study, we used a pressure sensor to quantify and facilitate adjustments to the prosthetic socket, correlating this information to the user's socket comfort.

SETTING

Outpatient clinic in a tertiary hospital in Singapore.

PARTICIPANTS

People (N = 16) with unilateral transtibial lower limb amputation using a prosthesis.

INTERVENTIONS

NA.

MAIN OUTCOME MEASURES

Peak pressure and socket comfort score (SCS).

RESULTS

The peak pressure value showed a statistically significant reduction across all participants following adjustments at a 50% delta change in pressure (p = .001). This was achieved with a mean number of 2.6 ± 1.4 adjustments per participant. Following the adjustments, the paired t-test results showed a mean increase between the first SCS and final SCS was 2.6 (p = .001).

CONCLUSION

The wound, redness, and pain resolved in 15 of 16 participants regardless of diabetic status following socket adjustments. Although the peak pressures values did not correlate to the SCS score, the reduction in peak pressure saw significant improvement to the SCS. The use of a portable sensor is a fast and efficient means to quantify adjustments inside the prosthetic socket and could potentially be considered as part of future care delivery.

A Scoping Review of Pressure Measurements in Prosthetic Sockets of Transfemoral Amputees during Ambulation: Key Considerations for Sensor Design

Sensor systems to measure pressure at the stump–socket interface of transfemoral amputees are receiving increasing attention as they allow monitoring to evaluate patient comfort and socket fit. However, transfemoral amputees have many unique characteristics, and it is unclear whether existing research on sensor systems take these sufficiently into account or if it is conducted in ways likely to lead to substantial breakthroughs. This investigation addresses these concerns through a scoping review to profile research regarding sensors in transfemoral sockets with the aim of advancing and improving prosthetic socket design, comfort and fit for transfemoral amputees. Publications found from searching four scientific databases were screened, and 17 papers were found relating to the aim of this review. After quality assessment, 12 articles were finally selected for analysis. Three main contributions are provided: a de facto methodology for experimental studies on the implications of intra-socket pressure sensor use for transfemoral amputees; the suggestion that associated sensor design breakthroughs would be more likely if pressure sensors were developed in close combination with other types of sensors and in closer cooperation with those in possession of an in-depth domain knowledge in prosthetics; and that this research would be facilitated by increased interdisciplinary cooperation and open research data generation.

Investigation of Orthopedic Prosthesis Socket Management after Transfemoral Amputation by Expert Survey

Prosthesis treatment requires the close interaction of different actors. In fitting prostheses to patients, special attention is given to the manufacturing of the socket. The continuous development of the technologies involved in the fitting and optimization of prostheses is shown in the literature. The assessment of orthopedic technicians and their influence in the process is thus far largely unexplored. Ten orthopedic technicians were interviewed about the socket fitting process after transfemoral amputation. The research goal was to clarify the socket treatment process with regards to the German context. The results showed that the orthopedic technicians focussing on the patient during the fitting process. This study underlines the importance of interaction and empathy. Volume fluctuations are decisive within the treatment process and are interactively influenced by various factors. Furthermore, the research emphasizes the need for appropriate assistive technologies and the potential for the further development of existing systems.

Towards Management of Residual Limb Volume: Monitoring the Prosthetic Interface Pressure to Detect Volume Fluctuations—A Feasibility Study

(1) Motivation: Variations in the volume of the residual limb negatively impact various aspects of prosthesis use including the prosthetic socket fit. Although volume adjustment systems mitigate corresponding fit problems to some extent, some users still find the management of these systems challenging. With the ultimate goal of creating a feedback system that assists users with the management of their volume adjustment systems, this study demonstrates the feasibility of detecting variations in the volume of the residual limb. (2) Methods: Measurements of the interface force at the bottom of the prosthetic socket were used as indicators of variations in the volume of the residual limb. Force sensitive resistors (FSRs) were placed at the bottom of participants’ prosthetic sockets to monitor the interface limb–socket force as participants walked on a flat surface. Two phases of experiments were carried out: The first phase considered variations simulated by three prosthetic sock plies, established the feasibility of detecting variations in the volume of the limb based on the interface force, and further determined the locations at which the interface force could be used to detect variations in the limb’s volume. Having validated the effectiveness of the proposed method in the first phase, the second phase was carried out to determine the smallest detectable variation of the limb’s volume using the proposed method. In this phase, variations simulated by one and two prosthetic sock plies were considered. Four and three volunteers with transtibial amputations participated in the first and the second phases, respectively. (3) Results: Results of the first phase showed that an increase in the volume of the limb resulted in a decrease in the force measured at the distal location of the prosthetic sockets of all participants; however, the smallest detected variation could not be statistically confirmed.

Optical coherence tomography for the investigation of skin adaptation to mechanical stress

BACKGROUND

Skin breakdown due to limb-socket interface stress is a significant problem for lower limb prosthesis users. While it is known that skin can adapt to stress to become more resistant to breakdown, little is understood about skin adaptation and few methods exist to noninvasively investigate it. In this study, we present novel, noninvasive imaging methods using Optical Coherence Tomography (OCT) to assess key features of the cutaneous microvasculature that may be involved in skin adaptation.

MATERIALS AND METHODS

Eight able-bodied participants wore a modified below-knee prosthetic socket for two weeks to stress the skin of their lower limb. Two OCT-based imaging tests were used to assess the function and structure, respectively, of the cutaneous microvasculature at multiple time points throughout the socket wear protocol.

RESULTS

A measurable reactive hyperemia response was reliably induced in the skin of study participants in the vascular function assessment test. The vascular structure assessment demonstrated excellent field-of-view repeatability, providing rich data sets of vessel structure. No statistically significant differences were found in any of the measurements when compared between time points of the adaptation protocol. The participants' limbs were likely not stressed enough by the able-bodied socket to induce measurable skin adaptation.

CONCLUSION

This study introduced new techniques to investigate skin adaptation to mechanical stress. If the key limitations are addressed, these methods have the potential to provide insight into the function and structure of the cutaneous microvasculature that previously could not be attained noninvasively.

How do transtibial residual limbs adjust to intermittent incremental socket volume changes?

BACKGROUND

Strategies to maintain prosthesis users' daily limb volume are needed.

OBJECTIVES

Test how intermittent incremental socket volume adjustments affect limb fluid volume and limb-socket distance.

STUDY DESIGN

Repeated measures.

METHODS

People with transtibial limb loss walked on an outdoor trail wearing a motor-driven adjustable socket that they adjusted a small amount, approximately 0.3% socket volume, every 2 min using a mobile phone app. Limb fluid volume and sensed distance between the socket and a target in their elastomeric liner were monitored. A gradual socket enlargement phase was followed by a gradual socket reduction phase.

RESULTS

An incremental socket enlargement significantly increased limb fluid volume (p < 0.001) but not sensed distance (p = 0.063). An incremental socket reduction significantly decreased both limb fluid volume (p < 0.001) and sensed distance (p < 0.001).

CONCLUSION

Participants' residual limb fluid volume increases during ambulation compensated for incremental socket volume increases. For incremental socket volume decreases, residual limb fluid volume decreases did not compensate and the socket fit became tighter.

CLINICAL RELEVANCE

Results support the hypothesis that for people without co-morbidities, intermittent incremental socket volume enlargements are an effective accommodation strategy to increase limb fluid volume while maintaining socket fit. Intermittent incremental socket volume reductions decreased limb fluid volume but also made the socket fit tighter.

Evaluation of Force Sensing Resistors for the Measurement of Interface Pressures in Lower Limb Prosthetics

Understanding pressure distributions at the limb-socket interface is essential to the design and evaluation of prosthetic components for lower limb prosthesis users. Force sensing resistors (FSRs) are employed in prosthetics research to measure pressure at this interface due to their low cost, thin profile, and ease of use. While FSRs are known to be sensitive to many sources of error, few studies have systematically quantified these errors using test conditions relevant to lower limb prosthetics. The purpose of this study was to evaluate FSR accuracy for the measurement of lower limb prosthetics interface pressures. Two FSR models (Flexiforce A201 and Interlink 402) were subjected to a series of prosthetic-relevant tests. These tests included: (1) static compression, (2) cyclic compression, and (3) a combined static and cyclic compression protocol mimicking a variable activity (Walk-Sit-Stand) procedure. Flexiforce sensors outperformed Interlink sensors and were then subjected to two additional tests: (4) static curvature and (5) static shear stress. Results demonstrated that FSRs experienced significant errors all five tests. We concluded that: (1) if used carefully, FSRs can provide an estimate of prosthetic interface pressure, but these measurements should be interpreted within the expected range of possible measurement error given the setup; (2) FSRs should be calibrated in a setup that closely matches how they will be used for taking measurements; and (3) both Flexiforce and Interlink sensors can be used to estimate interface pressures, however in most cases Flexiforce sensors are likely to provide more accurate measurements.

A finite element model to assess transtibial prosthetic sockets with elastomeric liners

People with transtibial amputation often experience skin breakdown due to the pressures and shear stresses that occur at the limb-socket interface. The purpose of this research was to create a transtibial finite element model (FEM) of a contemporary prosthesis that included complete socket geometry, two frictional interactions (limb-liner and liner-socket), and an elastomeric liner. Magnetic resonance imaging scans from three people with characteristic transtibial limb shapes (i.e., short-conical, long-conical, and cylindrical) were acquired and used to develop the models. Each model was evaluated with two loading profiles to identify locations of focused stresses during stance phase. The models identified five locations on the participants' residual limbs where peak stresses matched locations of mechanically induced skin issues they experienced in the 9 months prior to being scanned. The peak contact pressure across all simulations was 98 kPa and the maximum resultant shear stress was 50 kPa, showing reasonable agreement with interface stress measurements reported in the literature. Future research could take advantage of the developed FEM to assess the influence of changes in limb volume or liner material properties on interface stress distributions. Graphical abstract Residual limb finite element model. Left: model components. Right: interface pressures during stance phase.

Characteristics of a volume-adjustable compression chamber for transradial prosthetic interface

In the transradial limb–socket contact interface, the physiological properties and prosthetic operating habits of the residual limb might affect the comfort and functionality of the prosthesis. To enhance the comfort and functionality of the interface, a frame-type socket with four volume-adjustable compression chambers was proposed for the transradial amputation level. The contact pressure of the limb–socket interface was adjusted by the volume changes in the chambers and controlled by a vacuum pump and the corresponding control system. The parameters of the chamber were designed in accordance with the biomechanics of the forearm soft tissue. The chamber with a negative stiffness characteristic was theoretically compared with the chamber with a positive stiffness characteristic. The results showed that the former had a superior performance to the latter in safety and pump performance requirements. A physical model of the transradial frame-type prosthetic interface was also manufactured with four negative stiffness chambers. The experimental results showed that this new prosthetic interface achieved more fitting time and better performance in comfort and functionality than the fixed frame-type socket. This new prosthetic interface with volume-adjustable compression chambers might be an alternative choice for transradial amputees.

Adaptive sports technology and biomechanics: prosthetics

With the technologic advances in medicine and an emphasis on maintaining physical fitness, the population of athletes with impairments is growing. It is incumbent upon health care practitioners to make every effort to inform these individuals of growing and diverse opportunities and to encourage safe exercise and athletic participation through counseling and education. Given the opportunities for participation in sports for persons with a limb deficiency, the demand for new, innovative prosthetic designs is challenging the clinical and technical expertise of the physician and prosthetist. When generating a prosthetic prescription, physicians and prosthetists should consider the needs and preferences of the athlete with limb deficiency, as well as the functional demands of the chosen sporting activity. The intent of this article is to provide information regarding the current advancements in the adaptive sports technology and biomechanics in the field of prosthetics, and to assist clinicians and their patients in facilitating participation in sporting activities.

Interface pressure in transtibial socket during ascent and descent on stairs and its effect on patient satisfaction

BACKGROUND

Transtibial amputees encounter stairs and steps during their daily activities. The excessive pressure between residual limb/socket may reduce the walking capability of transtibial prosthetic users during ascent and descent on stairs. The purposes of the research were to evaluate the interface pressure between Dermo (shuttle lock) and Seal-In X5 (prosthetic valve) interface systems during stair ascent and descent, and to determine their satisfaction effects on users.

METHODS

Ten amputees with unilateral transtibial amputation participated in the study. Interface pressure was recorded with F-socket transducer (9811E) during stair ascent and descent at self-selected speed. Each participant filled in a questionnaire about satisfaction and problems encountered with the use of the two interface systems.

FINDINGS

The resultant mean peak pressure (kPa) was significantly lower for the Dermo interface system compared to that of the Seal-In X5 interface system at the anterior, posterior and medial regions during stair ascent (63.14 vs. 80.14, 63.14 vs. 90.44, 49.21 vs. 66.04, respectively) and descent (67.11 vs. 80.41, 64.12 vs. 88.24, 47.33 vs. 65.11, respectively). Significant statistical difference existed between the two interface systems in terms of satisfaction and problems encountered (P<0.05).

INTERPRETATION

The Dermo interface system caused less pressure within the prosthetic socket compared to the Seal-In X5 interface system during stair negotiation. The qualitative survey also showed that the prosthesis users experienced fewer problems and increased satisfaction with the Dermo interface system.

An experimental study of the interface pressure profile during level walking of a new suspension system for lower limb amputees

BACKGROUND

Different suspension systems that are used within prosthetic devices may alter the distribution of pressure inside the prosthetic socket in lower limb amputees. This study aimed to compare the interface pressure of a new magnetic suspension system with the pin/lock and Seal-In suspension systems.

METHODS

Twelve unilateral transtibial amputees participated in the study. The subjects walked on a level walkway at a self-selected speed. The resultant peak pressure with the three different suspension systems was recorded using F-socket transducers.

FINDINGS

There were significant statistical differences between the three studied suspension systems. Pair-wise analyses revealed that the mean peak pressure (kPa) was lower with the magnetic system than it was with the pin/lock system over the anterior and posterior aspects during one gait cycle (89.89 vs. 79.26 and 47.22 vs. 26.01, respectively). Overall, the average peak pressure values were higher with the Seal-In system than they were with the new magnetic lock and pin/lock system.

INTERPRETATION

The new magnetic system might reduce the pressure within the prosthetic socket in comparison to the pin/lock and Seal-In system during one gait cycle. This is particularly important during the swing phase of gait and may reduce the pain and discomfort at the distal residual limb in comparison to the pin/lock system.

Residual limb volume change: systematic review of measurement and management

Management of residual limb volume affects decisions regarding timing of fit of the first prosthesis, when a new prosthetic socket is needed, design of a prosthetic socket, and prescription of accommodation strategies for daily volume fluctuations. This systematic review assesses what is known about measurement and management of residual limb volume change in persons with lower-limb amputation. Publications that met inclusion criteria were grouped into three categories: group I: descriptions of residual limb volume measurement techniques; group II: studies investigating the effect of residual limb volume change on clinical care in people with lower-limb amputation; and group III: studies of residual limb volume management techniques or descriptions of techniques for accommodating or controlling residual limb volume. We found that many techniques for the measurement of residual limb volume have been described but clinical use is limited largely because current techniques lack adequate resolution and in-socket measurement capability. Overall, limited evidence exists regarding the management of residual limb volume, and the evidence available focuses primarily on adults with transtibial amputation in the early postoperative phase. While we can draw some insights from the available research about residual limb volume measurement and management, further research is required.