Anodic TiO2nanotube arrays for photocatalytic CO2conversion: comparative photocatalysis and EPR study

Efficient structure tuning over the defective modulated zirconium metal organic framework with active coordinate surface for photocatalyst CO2 reduction

Structure engineering of zirconium-based metal organic frameworks (MOFs) aims to develop efficient catalysts for transforming intermittent renewable energy into value-added chemical fuels. In order to have a deeper understanding of industrial scaling, it is vital to ascertain the favourable operational parameters that are necessary for projecting at the atomic level. The proposed paradigm provides a robust basis for the efficient design of MOFs based heterogeneous photocatalysts. In this study, set of defective MOF (D-NUiO66) was effectively produced using a modular acidic method. Afterwards, the D-NUiO66 was combined with CeO2 to form the D-CeNUiO66 heterojunction for the purpose of carbon dioxide reduction. The morphological aspect of the composite investigation suggested that D-CeNUiO66 had a mesoporous structure with favourable adsorption properties. The optimized D-CeNUiO66 photocatalyst showed the high activity for the reduction of CO2 to CO, with a rate of 38.6 µmolg-1h-1 and demonstrated remarkable repeatability in terms of CO production. The incorporation of defect sites in the D-NUiO66 enhanced the light response to visible light, resulting in reduced band gap of 2.9 eV. The photoelectrochemical tests indicated that the introduction of defects in the UiO66 and coupling CeO2 in the D-CeNUiO66 composite induced fast charge transfer, therefore suppressing the charge recombination rate. This study provides valuable insights into the use of defective engineering and heterojunction approaches to metal-organic frameworks for photocatalytic applications.

A Carbon-Free and Free-Standing Cathode From Mixed-Phase TiO2 for Photo-Assisted Li-CO2 Battery

Li-CO₂ battery provides a new strategy to simultaneously solve the problems of energy storage and greenhouse effect. However, the severe polarization of CO₂ reduction and CO₂ evolution reaction impede the practical application. Herein, anodic TiO₂ nanotube arrays are first introduced as carbon-free and free-standing cathode for photo-assisted Li-CO₂ battery, and the photo-assisted charge and discharge mechanism is first clarified from the perspective of photocatalysis. Mixed-phase TiO₂ exhibits a long cycling life of 580 h (52 cycles) at 0.025 mA cm^-2 and delivers a high discharge specific capacity of 3001 µAh cm^-2 under UV illumination. The charge voltage dramatically reduces from 4.53 to 3.03 V under UV illumination. The improvement of photo-assisted Li-CO₂ battery performance relies on the synergistic effect of the hierarchical porous structure, strong UV absorption, efficient separation, and transfer of photo-generated electrons and holes at hetero-phase junction, and the facilitation of photo-generated electrons and holes on CO₂ reduction and CO₂ evolution reaction. This work can provide useful guidance for designing efficient photocathode for photo-assisted Li-CO₂ battery and other metal-air batteries.

Effect of Thermal Treatment of Symmetric TiO2 Nanotube Arrays in Argon on Photocatalytic CO2 Conversion

Symmetric titania nanotube arrays (TiO2 NTs) are a well-known photocatalyst with a large surface area and band edge potentials suitable for redox reactions. Thermal treatment of symmetrical arrays of TiO2 nanotubes in argon was used to change the carbon content of the samples. The influence of the carbon content in the structure of symmetrical TiO2 NTs on their photoelectrochemical properties and photocatalytic activity in the conversion of CO2 into organic fuel precursors has been studied. The structure, chemical, and phase composition of obtained samples were studied by X-ray analysis, Raman spectroscopy, and SEM with energy dispersive analysis. It is established that carbon-related defects in the samples accumulate electrons on the surface required for the CO2 conversion reaction. It has been shown for the first time that varying the carbon content in symmetric TiO2 NTs arrays by annealing at different temperatures in argon makes it possible to control the yield of methane and methanol in CO2 conversion. It is revealed that too high a concentration of carbon dangling bonds promotes the growth of CO2 conversion efficiency but causes instability in this process. The obtained results show a high promise of symmetric carbon-doped TiO2 NTs arrays for the photocatalytic conversion of CO2.

Photoelectron Properties and Organic Molecules Photodegradation Activity of Titania Nanotubes with CuxO Nanoparticles Heat Treated in Air and Argon

Titania is very famous photocatalyst for decomposition of organic pollutants. Its photocatalytic properties significantly depend on the morphology and chemical composition of the samples. Herein, the TiO₂ nanotubes/Cu_xO nanoheterostructures have been synthesized and the effect of heat treatment performed in molecular atmospheres of air and argon on their photoelectrochemical and photocatalytic properties has been studied. The prepared samples have a higher reaction rate constant compared to TiO₂ nanotubes in the decomposition reaction of methylene blue molecules. It is established that in argon treated nanoheterostructures, the copper oxide is present in two phases, CuO and Cu₂O, while in air treated ones there is only CuO. In the TiO₂ nanotubes/Cu_xO samples, Cu²⁺ ions and molecular O₂^- radicals were detected while in TiO₂ nanotubes only carbon dangling bond defects are present. The dynamics of O₂^- radicals under illumination are discussed. It was shown that the TiO₂ nanotubes do not exhibit photocatalytic activity under visible light. The mechanism of the photocatalytic reaction on the surface of the TiO₂ nanotubes/Cu_xO samples was proposed. It is assumed that a photocatalytic decomposition of organic molecules under visible light at the surface of the nanoheterostructures under investigation is realized mainly by the reaction of these molecules with photogenerated O₂^- radicals. The results obtained are completely original and indicate the high promise of the prepared photocatalysts.

Photocatalytic CO2 Conversion Using Anodic TiO2 Nanotube-CuxO Composites

Nanosized titanium dioxide (TiO2) is currently being actively studied by the global scientific community, since it has a number of properties that are important from a practical point of view. One of these properties is a large specific surface, which makes this material promising for use in photocatalysts, sensors, solar cells, etc. In this work, we prepared photocatalysts based on TiO2 nanotubes for converting carbon dioxide (CO2) into energy-intensive hydrocarbon compounds. Efficient gas-phase CO2 conversion in the prepared single-walled TiO2 nanotube-CuxO composites was investigated. Parameters of defects (radicals) in composites were studied. Methanol and methane were detected during the CO2 photoreduction process. In single-walled TiO2 nanotubes, only Ti3+/oxygen vacancy defects were detected. The Cu2+ centers and O2− radicals were found in TiO2 nanotube-CuxO composites using the EPR technique. It has been established that copper oxide nanoparticles are present in the TiO2 nanotube-CuxO composites in the form of the CuO phase. A phase transformation of CuO to Cu2O takes place during illumination, as has been shown by EPR spectroscopy. It is shown that defects accumulate photoinduced charge carriers. The mechanism of methane and methanol formation is discussed. The results obtained are completely original and show high promise for the use of TiO2-CuxO nanotube composites as photocatalysts for CO2 conversion into hydrocarbon fuel precursors.