Leuco crystal violet-Pluronic F-127 3D radiochromic gel dosimeter

The Method of Direct and Reverse Phase Portraits as a Tool for Systematizing the Results of Studies of Phase Transitions in Solutions of Thermosensitive Polymers

It is shown that a more than significant amount of experimental data obtained in the field of studying systems based on thermosensitive hydrophilic polymers and reflected in the literature over the past decades makes the issue of their systematization and classification relevant. This, in turn, makes relevant the question of choosing the appropriate classification criteria. It is shown that the basic classification feature can be the number of phase transition stages, which can vary from one to four or more depending on the nature of the temperature-sensitive system. In this work, the method of inverse phase portraits is proposed for the first time. It was intended, among other things, to identify the number of phase transition stages. Moreover, the accuracy of this method significantly exceeds the accuracy of the previously used method of direct phase portraits since, for the first time, the operation of numerical differentiation is replaced by the operation of numerical integration. A specific example of the application of the proposed method for the analysis of a previously studied temperature-sensitive system is presented. It is shown that this method also allows for a quantitative comparison between the results obtained by the differential calorimetry method and the turbidimetry method. Issues related to increasing the resolution of the method of direct phase portraits are discussed.

On the Use of the Fricke-Pluronic F-127 Gel Dosimeter for Radiation Isocenter Testing of a Medical Linear Accelerator

This work presents a Fricke-XO-Pluronic F-127 2D radiochromic dosimeter with a flat-bed scanner for 2D reading and a dedicated data processing software package as a tool for performing coincidence testing of the radiation and mechanical isocenter of a medical accelerator. The optimal irradiation parameters were determined as follows: monitor units per beam and multi-leaf collimator gap, which are ≤750-≤2500 MU and 2-5 mm, respectively, for a cuboidal container with dimensions of 12 × 12 × 0.3 cm3. Despite the diffusion of Fe3+ ions occurring during irradiation, 2D reading can be performed at least 3 h after irradiation, without affecting the calculation performance of the coincidence test. The test was successfully performed for various irradiation settings. Overall, the Fricke-XO-Pluronic F-127 dosimeter has proven to be a potential tool for the coincidence testing of medical accelerators.

Fast Isocenter Determination Using 3D Polymer Gel Dosimetry with Kilovoltage Cone-Beam CT Reading and the PolyGeVero-CT Software Package for Linac Quality Assurance in Radiotherapy

This work presents an approach to the fast determination of a medical accelerator irradiation isocenter as a quality assurance (QA) procedure in radiotherapy. The isocenter determination tool is the tissue equivalent high-resolution 3D polymer gel dosimeter (PABIG^nx) in a dedicated container combined with kilovoltage imaging systems and the polyGeVero-CT software package (v. 1.2, GeVero Co., Poland). Two accelerators were employed: Halcyon and TrueBeam (Varian, USA), both equipped with cone beam computed tomography (CBCT) and iterative reconstruction CBCT (iCBCT) algorithms. The scope of this work includes: (i) the examination of factors influencing image quality (reconstruction algorithms and modes), radiation field parameters (dose and multi-leaf collimator (MLC) gaps), fiducial markers, signal averaging for reconstruction algorithms and the scanning time interval between consecutive scans, (ii) the examination of factors influencing the isocenter determination, image processing (signal averaging, background subtraction, image filtering) and (iii) an isocenter determination report using a 2D and 3D approach. An optimized protocol and isocenter determination conditions were found. The time and effort required to determine the isocenter are discussed.

Golden and Silver-Golden Chitosan Hydrogels and Fabrics Modified with Golden Chitosan Hydrogels

Golden and silver-golden chitosan hydrogels and hydrogel-modified textiles of potential biomedical applications are investigated in this work. The hydrogels are formed by reactions of chitosan with HAuCl4·xH2O. For above the critical concentration of chitosan (c*), chitosan-Au hydrogels were prepared. For chitosan concentrations lower than c*, chitosan-Au nano- and microgels were formed. To characterise chitosan-Au structures, sol-gel analysis, UV-Vis spectrophotometry and dynamic light scattering were performed. Au concentration in the hydrogels was determined by the flame atomic absorption spectrophotometry. Colloidal chitosan-Au solutions were used for the modification of fabrics. The Au content in the modified fabrics was quantified by inductively coupled plasma mass spectrometry technique. Scanning electron microscopy with energy dispersion X-ray spectrometer was used to analyse the samples. Reflectance spectrophotometry was applied to examine the colour of the fabrics. The formation of chitosan-Au-Ag hydrogels by the competitive reaction of Au and Ag ions with the chitosan macromolecules is reported.

Features of PABIGnx 3D Polymer Gel as an Ionising Radiation Dosimeter

This work presents the features of the PABIG^nx 3D polymer gel dosimeter. It consists of two cross-linkers: poly(ethylene glycol) diacrylate (PEGDA), as one biacrylic component, and N,N′-methylenebisacrylamide (MBA), which is another cross-linker often used in 3D dosimeters. Additionally, it contains oxygen scavenges of copper sulfate pentahydrate and ascorbic acid. All ingredients are embedded in a physical gel matrix of gelatine. Upon irradiation, the biacrylic cross-linking agents (PEGDA and MBA) undergo radical polymerisation and cross-linking, which is manifested by the appearance of the opacity of the intensity related to the absorbed dose. PABIG^nx was irradiated with an oncological source of ionising radiation, and analysed by using a nuclear magnetic resonance (0.5 T). The following characteristics were obtained: (i) linear and dynamic dose-response of 0.5 to ~18 Gy and 40 Gy, respectively, (ii) dose sensitivity of 0.071 ± 0.001 Gy⁻¹ s⁻¹, (iii) integral 3D dose distribution for at least 24 days after irradiation, (iv) adequate batch-to-batch reproducibility, (v) dose-response independent of irradiation with 6 MV photons, 15 MV photons, 6 MV photons FFF of 0.0168–0.1094 Gy/s dose rates, and (vi) soft tissue equivalence. The study showed that the features of PABIG^nx confirm its suitability for use in 3D radiotherapy dosimetry.

Study of NBT-Pluronic F-127 Gels as 1D UV Radiation Dosimeters for Measurement of Artificial Light Sources

This work reports on radiochromic dosimeters for 1D UV light measurements. The dosimeter is composed of a 25% Pluronic F–127 that forms a physical gel matrix and nitro blue tetrazolium chloride (NBT) as a radiation-sensitive compound. This dosimeter was exposed to UVA, UVB and UVC radiation, and the radiochromic reactions were followed with reflectance spectrophotometry including changes in light reflectance and color coordinates in the CIELAB color system. The exposition of dosimeters to all UV radiation caused color changes from pale yellow to dark violet, and its intensity increased with increasing absorbed dose. The effects of NBT concentration and UV radiation type on the dose–response of the dosimeters were also examined. The results obtained reveal that the dosimeters are the least sensitive to irradiation with UVC and the most sensitive to irradiation with UVB (e.g., dosimeter with 2 g/dm³ of NBT was characterized by the following parameters: the threshold dose 0.1 J/cm²; the dose sensitivity −5.97 ± 0.69 cm²/J; the linear dose range 0.1–2.5 J/cm²; the dynamic dose range was equal to 0.1–3 J/cm²). The results obtained reveal that the NBT–Pluronic F–127 dosimeters can be potentially useful as 1D sensors for artificial UV radiation sources measurements.

Thermally Controllable Decolorization of Reusable Radiochromic Complex of Polyvinyl Alcohol, Iodine and Silica Nanoparticles (PAISiN) Irradiated with γ-rays

Some medical and industry workers using ionizing radiation sources have potential risks of accidental high-dose exposure of their extremities, particularly their hands. While practical dosimeters suitable for on-site real-time monitoring of hand exposure are not yet available, they are desirable to be developed. Thus, the authors focused on the application of a reusable radiochromic complex composed of polyvinyl alcohol, iodide and silica nanoparticles, named “PAISiN”, and examined their dose responses and thermal stabilities of radiochromic reactions. Three PAISiN samples each were irradiated with 5, 10 and 20 Gy of 137Cs γ-rays, and time changes of the radiation-induced colors were observed at different temperatures: 20 °C (in a laboratory), 40 °C (in an oven) and 5.5 °C (in a refrigerator). It was confirmed that the PAISiN samples presented a red color that was easily detectable by the naked eyesight immediately after irradiation. The coloration was cleared within 24 h for 5 Gy irradiation at room temperature. The decolorization process was remarkably accelerated at 40 °C; it was erased in just 2 h. In contrast, storing in the refrigerator (5.5 °C) kept the color persistently for at least 4 days. These findings indicate that we could flexibly control the decolorization process of PAISiN in accordance with the objective of radiation monitoring.

Study of the Optimal Composition and Storage Conditions of the Fricke-XO-Pluronic F-127 Radiochromic Dosimeter

This paper presents the results of research on the Fricke–XO–Pluronic F–127 dosimeter. It consists of a Fricke dosimetric solution and xylenol orange (XO), which are embedded in a matrix of poly(ethylene oxide)-block-poly(propylene oxide)-block-poly(ethylene oxide) (Pluronic F–127). Upon irradiation, Fe⁺² ions transform into Fe⁺³, forming a colored complex with XO ([XO-Fe]⁺³). The color intensity is related to the dose absorbed. The optimal composition, storage conditions, and radiation-induced performance of the Fricke–XO–Pluronic F–127 dosimeter were investigated. The optimal composition was found to be 1 mM FAS, 50 mM sulfuric acid (H₂SO₄), 0.165 mM XO in 25% Pluronic F–127. The basic features of this dosimeter are discussed, such as dose sensitivity, linear and dynamic dose range, stability before and after irradiation, storage conditions, dose response for irradiation with 6 and 15 MV photons, and batch-to-batch reproducibility. The obtained results showed a certain potential of the Fricke–XO–Pluronic F–127 for radiotherapy dosimetry.

Fluorescent organic particle doped polymer-based gel dosimeter for neutron detection

The purpose of this work is to develop a material capable of detecting neutrons produced by photodisintegration in a linear accelerator for its medical use. In this study, we have developed a gel-like material doped with fluorescent organic particles. PPO at 1 wt% is used as primary dopant and POPOP as secondary one at 0.03 wt%. A set of four samples is produced, with boric acid concentrations of 0, 400, 800 and 1200 ppm. The viscoelastic properties of the material are characterized with rheological measurements, finding a gel-like behavior, i.e., a material that can keep its original shape if no stresses are applied, but can also be deformed by applying a moderate shear rate. Furthermore, the material was irradiated with gamma, electron, and neutron emission sources from ¹³⁷Cs, ²²Na, ⁶⁰Co, ²¹⁰Po, ⁹⁰Sr and ²⁴¹AmBe, and its response was measured in two different experimental settings, in two different institutions, for comparative purposes. From these measurements, one can clearly establish that the new material detects neutrons, electrons, and gammas within the MeV regions and below. Thus, our findings show that the developed material and its properties make it a promising technology for its use in a neutron detector.

Three-dimensional Winston-Lutz test using reusable polyvinyl alcohol-iodide (PVA-I) radiochromic gel dosimeter

Medical linear-accelerator-based stereotactic radiosurgery (SRS) using a stereotactic apparatus or image-guided radiotherapy system for intracranial lesions is performed widely in clinical practice. In general, Winston-Lutz (WL) tests using films or electric portal imaging devices (EPIDs) have been performed as pre-treatment and routine quality assurance (QA) for the abovementioned treatment. Two-dimensional displacements between the radiation isocentre and mechanical isocentre are analysed from the test; therefore, it is difficult to identify the three-dimensional (3D) isocentre position intuitively. In this study, we developed an innovative 3D WL test for SRS-QA using a novel radiochromic gel dosimeter based on a polyvinyl alcohol-iodide (PVA-I) complex that can be reused after annealing. A WL gel phantom that was consisted of the PVA-I gel dosimeter poured into a tall acrylic container and an embedded small tungsten sphere was used as a position detector. A flatbed scanner was used to analyse the isocentre position. The measured 3D isocentre accuracy from the gel-based WL test was within 0.1 mm compared with that obtained from the EPID-based WL test. Furthermore, excellent reusability of the WL gel phantom was observed in long-term SRS isocentre verification, in which clinical SRS cases involving repeated irradiation and annealing were analysed. These results demonstrate the high accuracy and reliable evaluation of the isocentre position using an innovative test. In addition, the clinical-based routine SRS-QA using the PVA-I gel dosimeter demonstrates a highly convenience while affording an easy and fast analysis process.

Anisotropic diffusion of Fe ions in Fricke-XO-Pluronic F-127 and Fricke-XO-gelatine 3D radiotherapy dosimeters

A new radiochromic dosimeter was examined with Raman spectroscopy and an optical approach for assessment of 3D dose distribution integrity. The acronym of the dosimeter is Fricke-XO-Pluronic F-127, where XO denotes xylenol orange; Pluronic F-127 is a copolymer matrix of poly(ethylene oxide)-block-poly(propylene oxide)-block-poly(ethylene oxide), and the dosimeter contains the components of a Fricke dosimetric solution. Two dosimeter samples in cuvettes were partially irradiated such that a radiation dose was absorbed at the bottom of the cuvettes. After irradiation, one sample was stored upside down such that the irradiated part was at the top and another one was stored with the irradiated part at the bottom. Two diffusion coefficients of ferric ion complexes with XO ([XO-Fe]⁺³) were calculated. They were compared with those for similar dosimeter, however with gelatine matrix instead of Pluronic F-127. The results obtained indicate an impact of the gravitational force on the diffusion of [XO-Fe]⁺³ions over time after irradiation and thus a possibility of severely undermining the integrity of a dose distribution in irradiated dosimeter. The conclusions drawn suggest the necessity of examination of different 3D Fricke dosimeter compositions for anisotropic diffusion of ferric ions.

NBT-Pluronic F-127 Hydrogels Printed on Flat Textiles as UV Radiation Sensors

This work reports on the surface-modified woven fabrics for use as UV radiation sensors. The cotton and polyamide fabrics were printed with radiochromic hydrogels using a screen-printing method. The hydrogels used as a printing paste were composed of water, poly(ethylene oxide)-block-poly(propylene oxide)-block-poly(ethylene oxide) (Pluronic F-127) as a gel matrix and nitro blue tetrazolium chloride as a radiation-sensitive compound. The development of the hydrogels' colour occurs after exposure to UV radiation and its intensity increases with increasing absorbed dose. The features of the NBT-Pluronic F-127 radiochromic hydrogels and the fabrics printed with the hydrogels were examined using UV-Vis and reflectance spectrophotometry as well as scanning electron microscopy (SEM). The effects of NBT concentration and UV radiation type (UVA, UVB, UVC) on dose responses of the hydrogels and printed fabrics were also examined. The results obtained reveal that the fabrics printed with NBT-Pluronic F-127 hydrogels can be potentially useful as UV radiation sensors.

Clinical radiotherapy application of N-vinylpyrrolidone-containing 3D polymer gel dosimeters with remote external MR-reading

PURPOSE

Advanced 3D dosimetry is required for verifications of complex dose distributions in modern radiotherapy. Two 3D polymer gel dosimeters, coupled with magnetic resonance (MR) imaging (3 T MRI) readout and data processing with polyGeVero® software, were tested for the verification of calculated 3D dose distributions by a treatment planning system (TPS) and ArcCHECK®-3DVH®, related to eradication of a lung tumour.

METHODS

N-vinylpyrrolidone-containing 3D polymer gel dosimeters were used: VIC (containing ascorbic acid and copper sulfate pentahydrate) and VIC-T (containing tetrakis(hydroxymethyl)phosphonium chloride). Three remote centers were involved in the dosimeters preparation and irradiation (Poland), and MRI (Austria). Cross beam calibration of the dosimeters and verification of a 3D dose distribution calculated with an Eclipse External Beam TPS and ArcCHECK®-3DVH® were performed. The 3D-to-3D comparisons of the VIC and VIC-T with TPS and ArcCHECK®-3DVH® along with ArcCHECK®-3DVH® versus TPS dose matrixes were performed with the aid of the polyGeVero® by analyzing dose profiles, isodoses lines, gamma index, gamma angle, dose difference, and related histograms.

RESULTS

The measured MR-relaxation rate (R₂ = 1/T₂) for the dosimeters relates to the dose, as follows: R₂ = 0.0928 ± 0.0008 [Gy^-1 s^-1] × D [Gy] + 2.985 ± 0.012 [s^-1] (VIC) and 0.1839 ± 0.0044 [Gy^-1 s^-1] × D [Gy] + 2.519 ± 0.053 [s^-1] (VIC-T). The 3D-to-3D comparisons revealed a good agreement between the measured and calculated 3D dose distributions.

CONCLUSIONS

VIC and VIC-T with 3T MRI readout and polyGeVero® showed potential for verifications of calculated irradiation plans. The results obtained suggest the implementation of the irradiation plan for eradication of the lung tumour.