Evaluation of the adaptation of dental polymers using cross-polarization optical coherence tomography

An Eggshell-Based Toothpaste as a Cost-Effective Treatment of Dentin Hypersensitivity

Objectives This study aimed to test the efficacy of two experimentally produced eggshell-based toothpastes on dentinal tubules occlusion.

Materials and Methods Two experimental eggshell toothpastes, based on natural ingredients, with or without titanium dioxide nanoparticles (TNPs) were produced and coded “TNPs eggshell toothpaste [TNPsESTP]” or “eggshell toothpaste [ESTP],” respectively. Mid-coronal dentin discs, from 28 human extracted molar teeth, etched with 37% phosphoric acid for 60 seconds to simulate the hypersensitive dentin, were randomly divided into four groups—G1: no treatment (negative control), G2: ESTP treated, G3: TNPsESTP treated, and G4: Biorepair treated (positive control). All treated discs were brushed for 2 weeks and 1 month using a toothbrush simulator at 40 mm/s. Dentinal tubules occlusion was studied using a cross-polarization optical coherence tomography (CP-OCT) and scanning electron microscopy (SEM).

Statistical Analysis Unpaired t -test was conducted using GraphPad software (San Diego, California, United States). Continuous variables were expressed as means ± standard deviation and p < 0.05 was considered statistically significant.

Results From CP-OCT, a marked increase in surface reflectivity of dentin was observed after brushing with tested toothpastes. ESTP and NPsESTP showed higher or comparable grayscale values than Biorepair indicating increase in surface density of dentin. From SEM, at 2 weeks, ESTP showed comparable number of completely occluded dentinal tubules to Biorepair. TNPsESTP showed significantly lower numbers of CODT than Biorepair. At 1 month, the number of CODT was difficult to count for all treated groups. Both ESTP and TNPsESTP showed significantly higher numbers of partially occluded dentinal tubules than Biorepair.

Conclusion ESTP or TNPsESTP could offer a cost-effective substitute for the treatment of dentin hypersensitivity.

Optical comparison between micro-CT and OCT in imaging of marginal composite adaptation: Observational study

Dental composite is the most used aesthetic restorative biomaterial worldwide. However, it undergoes polymerisation shrinkage that could lead to loss of the interfacial seal between tooth and resin in some circumstances. This demands high-resolution imaging technologies to detect these defects. This study carried out a comparison between microcomputed tomography (micro-CT; Shimadzu, Japan) and swept-source optical coherence tomography (SS-OCT; Santec, Japan) in the detection of marginal adaptation defects at the tooth-resin interface. Unlike in micro-CT, it was possible to outline interfacial gaps along with tooth-resin interfaces with SS-OCT, which was attributed to the Fresnel diffraction of light. This in vitro comparison demonstrates SS-OCT has great potential in dental imaging to effectively assess dental composite adaptation and marginal defects when high resolution is desired in real time. LAY DESCRIPTION: Detection of tooth-colored restoration defects had been assessed by different radiographic methods. However, most of these methods are either invasive or suffer from low-resolution. In this study, a comparison has been carried out between two different high-resolution imaging systems; microcomputed tomography and optical coherence tomography, to explore their potentials in detecting restorations defects. The results showed optical coherence tomography has a great accuracy in locating the underlying defects when the obtained images were validated against confocal laser scanning microscopy images.

Effect of light irradiation condition on gap formation under polymeric dental restoration; OCT study

OBJECTIVE

To investigate the effect of two light-curing systems; quartz tungsten-halogen (QTH) and light-emitting diode (LED), and irradiation time on interfacial gap formation of dental composite resin restorations bonded with an adhesive resin using optical coherence tomography (OCT).

MATERIALS AND METHODS

Forty cavities were prepared in extracted human molar teeth and divided into four groups (n=10) based on the type of light curing system QTH (LITEX 680A) and LED (Demi Plus) and curing duration (10 s or 40 s). A single-step self-etching dental adhesive (Tetric® N-Bond; Ivoclar Vivadent AG, Schaan, FL, Liechtenstein) was applied and polymerized with QTH for 10 s (QTH-10), or for 40 s (QTH-40). Similarly, the adhesive in LED-10 and LED-40 groups was polymerized with an LED for 10 s or 40 s, respectively. Then, all specimens were restored with Filtek™ Z350 XT flowable composite (3M ESPE AG, St. Paul, MN, USA) and immersed in ammoniacal silver-nitrate contrasting solution. Cross-sectional images were recorded at every 250μm using cross-polarization OCT system (CP-OCT; IVS-300, Santec, Komaki, Aichi, Japan). Image analysis to quantify the percentage of gap at resin-dentin interface was performed using a custom plugin for ImageJ software.

RESULTS

Data analysis using one-way ANOVA showed a significant difference in mean gap percentage between the four test groups (p<0.0001). Mean gap percentage values were 75.8%, 53.2%, 9.9% and 5.6%. The highest for LED-10 followed by LED-40 (p <0.05). QTH-40 revealed a slightly better adaptation compared with QTH-10, but the difference between them was not significant (p <0.05).

CONCLUSION

CP-OCT with a contrast agent is a useful non-invasive imaging tool for dental composite resin materials. QTH showed better results than LED under the experimental conditions. When using an LED light-curing unit, prolonged irradiation improved interfacial adaptation of dental composite bonded with a self-etching adhesive.