The radicular dentine temperature during laser irradiation: an experimental study

Histologic Evaluation of Three Methods of Periodontal Root Surface Treatment in Humans

BACKGROUND

Removing subgingival plaque and calculus is a major goal of periodontal treatment. Few attempts have been made to evaluate the use of lasers for root surface debridement in periodontal therapy. The aim of the present study was to compare, histologically, the effects of hand instrumentation, ultrasonic instrumentation, and CO2 lasers on the root surfaces of teeth treated in situ.

METHODS

A total of 33 teeth scheduled for extraction due to severe periodontal disease were divided into three groups. In the first group, teeth were treated by ultrasonic bactericidal curettage (UBC) with an ultrasonic scaler; in the second group, teeth were treated by hand instrumentation; and in the third group, after hand instrumentation, roots were lased by a CO2 laser. The samples were then processed for histological examination.

RESULTS

In the first and second groups, plaque and calculus were present in interradicular septa, lacunae, and surface concavities. In the third group, surfaces of specimens treated by a low-power defocused CO2 laser showed areas devoid of cementum, with completely sealed dentinal tubules, and no bacterial cell remnants.

CONCLUSIONS

The CO2 laser treatment, used at low power and in the defocused mode, combined with traditional mechanical instrumentation, could improve root surface debridement of periodontally involved teeth. More extensive, long-term studies are needed to confirm this hypothesis.

Effect of ER:YAG and diode laser irradiation on the root surface: morphological and thermal analysis

BACKGROUND

The aim of the present study was to compare the effects of Er:YAG and diode laser treatments of the root surface on intrapulpal temperature after scaling and root planing with hand instruments.

METHODS

Fifteen extracted single-rooted teeth were scaled and root planed with hand instruments. The teeth were divided into 3 groups of 5 each and irradiated on their buccal and lingual surfaces: group A: Er:YAG laser, 2.94 microm/100 mJ/10 Hz/30 seconds; group B: diode laser, 810 nm/1.0 W/0.05 ms/30 seconds; group C: diode laser, 810 nm/1.4 W/0.05 ms/30 seconds. The temperature was monitored by means of a type T thermocouple (copper-constantan) positioned in the pulp chamber to assess pulpal temperature during and before irradiation. Afterwards, the specimens were longitudinally sectioned, and the buccal and lingual surfaces of each root were analyzed by scanning electron microscopy.

RESULTS

In the Er:YAG laser group, the thermal analysis revealed an average temperature of -2.2 +/- 1.5 degrees C, while in the diode laser groups, temperatures were 1.6 +/- 0.8 degrees C at 1.0 W and 3.3 +/- 1.0 degrees C at 1.4 W. Electronic micrographs revealed that there were no significant morphological changes, such as charring, melting, or fusion, in any group, although the specimens were found to be more irregular in the Er:YAG laser group.

CONCLUSIONS

The application of Er:YAG and diode lasers at the utilized parameters did not induce high pulpal temperatures. Root surface irregularities were more pronounced after irradiation with an Er:YAG laser than with a diode laser.

The radicular dentine temperature during laser irradiation: a numerical modeling

The boundary element method is well adjusted to the numerical resolution of thermal diffusion problems existing in complex volumes such as teeth. This technique is used to determine the temperatures in the bulk and on the surface of a tooth illuminated by a CO2 laser beam. The parameters taken into account in calculations include power absorbed by the tooth, laser irradiation time, and diameter of the beam on the tooth. In each case, a very fast and short heating period is observed on the tooth surface; then, the temperature decreases slowly. Inside the tooth, temperature variations are small or nonexistent. Temperature increases due to a laser beam remain concentrated at the impact region. Results are in reasonable agreement with experimental results.