Assessment of Caries-Affected Dentin Adhesive Interface Treated with Contemporary Conditioning Techniques

Remineralizing pretreatment using Casein phosphopeptide-amorphous calcium phosphate fluoride, self-assembling peptide, and Nanohydroxyapatite gel activation via invisible infrared light on the dentin microhardness and micro shear bond strength to the composite restoration

AIM

Different remineralizing pretreatments Casein phosphopeptide-amorphous calcium phosphate fluoride (CPP-ACPF), tricalcium phosphate fluoride (TCP-F), self-assembling peptide (SAP) P11-4 and 10% Nanohydroxyapatite (nHA) gel activation via invisible infrared light on the dentin microhardness (MH) and micro shear bond strength (µSBS) of composite restoration.

METHODS

Seventy-five human molar teeth were collected and the dentinal surface of all the samples was exposed to different demineralizing solutions. (n=15) Group 1 (demineralized dentin), Group 2 (CPP ACP), Group 3 (TCP-F), Group 4 (SAP P11-4), Group 5 (nHA gel activation via invisible infrared light). MH assessment was performed using Vickers hardness. Each group of 10 samples was subjected to composite restoration buildup and µSBS were tested. The debonded samples were then observed under a stereo-microscope for failure analysis. ANOVA was conducted, along with Tukey's post hoc analysis, to examine the µSBS of composite and MH of the remineralized surface.

RESULTS

nHA gel activation via invisible infrared light pretreated specimens showed the maximum outcomes of surface hardness (331.2 ± 77.3) and bond strength (10.38 ± 2.77). However, Group 4 (SAP P11-4) (148.3 ± 29.2) remineralized dentin displayed minimum scores of MH and µSBS (5.88 ± 1.01).

CONCLUSION

Remineralizing pretreatment nHA gel activation via invisible infrared light and casein phosphopeptide-amorphous calcium phosphate fluoride seem to improve the dentin MH and µSBS of the composite restoration.

Effect of Casein Phosphopeptide-Amorphous Calcium Phosphate, Proanthocyanidin, Carbon Dioxide Laser Remineralization on the Bond Integrity of Composite Restoration Bonded to Caries-Affected Dentin

Objective: Assessment of different remineralizing pretreatment casein phosphopeptide-amorphous calcium phosphate (CPP-ACP), proanthocyanidin (PA), carbon dioxide laser (CO2), eggshell solution (ES) on the shear bond strength (SBS) of resin composite bonded to remineralized carious-affected dentin (CAD). Materials and methods: Eighty human molars were collected with occlusal caries that extended about halfway into the dentin. Using a water-cooled, low-speed cutting saw, a flat, mid-coronal dentin surface was exposed. CAD was differentiated from healthy dentin. Based on the remineralizing agent used on the CAD surface, the teeth were arbitrarily allocated into five groups (n = 10). Group 1: no remineralizing agent, Group 2: CPP-ACP, Group 3: 6.5% PA solution, Group 4: CO2 laser, and Group 5: ES solution. All samples were bonded to composite and light cured and thermocycled. SBS and failure mode analysis were performed using universal testing and stereomicroscope 40 × . Using SPSS, SBS, and failure mode data were analyzed using analysis of variance and Tukey's honesty significant difference (HSD) test Results: Group 3 (6.5% PA solution; 15.59 ± 1.44 MPa) samples established the maximum bond integrity. Nevertheless, Group 1 (No remineralizing agent; 11.19 ± 1.21 MPa) exhibited the minimum outcome of bond strength. Intergroup comparison analysis showed that Group 1 (No remineralizing agent), Group 2 (CPP-ACP), and Group 4 (CO2 laser) established comparable values of bond strength (p > 0.05). Likewise, Group 3 (6.5% PA solution) and Group 5 (EA solution) also revealed equivalent bond integrity (p > 0.05). Conclusions: PA and ES are considered potential remineralizing agents used for caries-affected dentin surfaces in improving bond integrity to composite resin. However, further studies are advocated to extrapolate the findings of this study.

Phycocyanin-loaded silver nanoparticles activated with photodynamic therapy and Nd: YAG laser for caries-affected dentin disinfection: Impact on Streptococcus mutans survival rate and shear bond strength to the tooth-colored restorative material

AIMS

To assess the impact of various cavity disinfectants PC-PDT (Phycocyanin activated by Photodynamic therapy), PC@AgNPs-PDT (Phycocyanin and silver nanoparticles activated by PDT), and Nd: YAG laser on the survival rate of S.mutans and the bond integrity of composite restoration METHODS: Sixty human mandibular molars that scored 4 and 5 based on ICDAS criteria were included. The infected dentin was removed while the CAD was preserved based on visual, tactile, and staining assessment. S.mutans were cultured on the CAD of twenty samples. All the specimens were indiscriminately distributed into four groups based on cavity disinfection (n=20 each includes n = 5 each group incubated with S.mutans) Group 1: CHX, Group 2: Nd:YAG laser, Group 3: PC-PDT and Group 4: PC@AgNPs-PDT. S.mutans survival rate was assessed for each group(n = 5). Forty samples underwent composite bonding for SBS and failure mode assessment using universal testing machine (UTM) and stereomicroscope. The calculations for the mean and standard deviation (SD) and their comparison among different groups were performed using a one-way analysis of variance (ANOVA) and the Tukey post hoc test (p ≤ 0.05) RESULTS: CAD surface treated disinfected with PC@AgNPs-PDT yielded the lowest survival rates (0.13 ± 0.05 CFU/ml) and highest SBS (17.23 ± 1.45 MPa). Group 1 (CHX) unveiled the highest survival rate of S.mutans (0.33 ± 0.12 CFU/ml). However, Group 2 (Nd:YAG Laser) (11.87 ± 0.67 MPa) presented the lowest SBS CONCLUSION: The combination of Phycocyanin loaded with silver nanoparticles and activated with Photodynamic therapy demonstrates the highest antimicrobial potential and bond strength of composite restorations.

Aluminum zirconate nanoparticles in etch and rinse adhesive to caries affected dentine: An in-vitro scanning electron microscopy, elemental distribution, antibacterial, degree of conversion and micro-tensile bond strength assessment

To incorporate different concentrations of Al2O9Zr3 (1%, 5%, and 10%) nanoparticles (NP) into the ER adhesive and subsequently assess the impact of this addition on the degree of conversion, μTBS, and antimicrobial efficacy. The current research involved a wide-ranging examination that merged various investigative techniques, including the application of scanning electron microscopy (SEM) for surface characterization of NP coupled with energy-dispersive x-ray spectroscopy (EDX), Fourier-transform infrared (FTIR) spectroscopy, μTBS testing, and microbial analysis. Teeth were divided into four groups based on the application of modified and unmodified three-step ER adhesive primer. Group 1 (0% Al2O9Zr3 NPs) Control, Group 2 (1% Al2O9Zr3 NPs), Group 3 (5% Al2O9Zr3 NPs), and Group 4 (10% Al2O9Zr3 NPs). EDX analysis of Al2O9Zr3 NPs was performed showing elemental distribution in synthesized NPs. Zirconium (Zr), Aluminum (Al), and Oxides (O2). After primer application, an assessment of the survival rate of Streptococcus mutans was completed. The FTIR spectra were analyzed to observe the characteristic peaks indicating the conversion of double bonds, both before and after the curing process, for the adhesive Etch and rinse containing 1,5,10 wt% Al2O9Zr3 NPs. μTBS and failure mode assessment were performed using a Universal Testing Machine (UTM) and stereomicroscope respectively. The μTBS and S.mutans survival rates comparison among different groups was performed using one-way ANOVA and Tukey post hoc (p = .05). Group 4 (10 wt% Al2O9Zr3 NPs + ER adhesive) specimens exhibited the minimum survival of S.mutans (0.11 ± 0.02 CFU/mL). Nonetheless, Group 1 (0 wt% Al2O9Zr3 NPs + ER adhesive) displayed the maximum surviving S.mutans (0.52 ± 0.08 CFU/mL). Moreover, Group 2 (1 wt% Al2O9Zr3 NPs + ER adhesive) (21.22 ± 0.73 MPa) samples displayed highest μTBS. However, the bond strength was weakest in Group 1 (0 wt% Al2O9Zr3 NPs + ER adhesive) (14.13 ± 0.32 MPa) study samples. The etch-and-rinse adhesive exhibited enhanced antibacterial activity and micro-tensile bond strength (μTBS) when 1% Al2O9Zr3 NPs was incorporated, as opposed to the control group. Nevertheless, the incorporation of Al2O9Zr3 NPs led to a decrease in DC. RESEARCH HIGHLIGHTS: 10 wt% Al2O9Zr3 NPs + ER adhesive specimens exhibited the minimum survival of S.mutans. 1 wt% Al2O9Zr3 NPs + ER adhesive samples displayed the most strong composite/CAD bond. The highest DC was observed in Group 1: 0 wt% Al2O9Zr3 NPs + ER adhesive.

Adhesive Bond Strength of Restorative Materials to Caries-Affected Dentin Treated with Antimicrobial Photodynamic Therapy: A Systematic Review and Meta-Analysis

Objective: This systematic review aimed to evaluate the adhesive bond strength of restorative materials to caries-affected dentin (CAD) treated with antimicrobial photodynamic therapy (aPDT) in comparison with conventional chemical disinfectants. Methods: Three databases, including the Web of Science, Scopus, and PubMed, were searched to address the focused question: "What is the effect of aPDT compared to conventional chemical disinfection techniques on the adhesive bond strength of restorative materials to CAD?." Search keywords included "dentin*" "adhes bond*" "caries-affected dentin" "photodynamic "photochemotherapy" "photosensitizing agent" "phototherapy" "photoradiation" "laser" "light activated" "photoactivated." A fixed-effects model was used in each meta-analysis and the inverse variance was used to calculate the standard mean difference (SMD). For evaluating the statistical heterogeneity, the Cochrane's Q test and the I2 statistics were used. The risk of bias was evaluated based on the Cochrane Collaboration's tool. Results: Fourteen studies were included in the qualitative as well as quantitative analysis. The results of the meta-analyses exhibited an SMD of 2.38% [95% confidence interval (CI): 2.03-2.73; p < 0.00001], indicating a statistically significant difference in the shear bond strength scores between the tested group (samples treated with aPDT) and the control group (i.e., favoring the sound dentin and/or conventional chemical disinfectants). Contrarily, an SMD of -1.46% (95% CI: -2.04 to -0.88; p < 0.00001) and -0.37% (95% CI: -0.70 to -0.03; p = 0.03) was observed, indicating a statistically significant difference in the microtensile bond strength (μTBS), as well as microleakage scores between the tested group (favoring the samples treated with aPDT) and the control group (i.e., sound dentin and/or conventional chemical disinfectants). Conclusions: Adhesive bond strength of restorative materials to CAD treated with conventional chemical disinfectants showed superior outcomes compared to photodynamic therapy (aPDT).

Bleached enamel reversal using grape seed extract, green tea, curcumin-activated photodynamic therapy, and Er: YAG on microleakage and bond integrity of composite material bonded to the enamel surface

AIMS

Bleached enamel reversal using antioxidants sodium ascorbate (SA), Green tea extract (GTE), grape seed extract (GSE), Curcumin photosensitizer (CP) and Er: YAG laser on the adhesive strength and marginal leakage of composite material bonded to the bleached enamel surface.

MATERIALS AND METHODS

Enamel surface of hundred and twenty sound human first premolar teeth was cleansed using pumice and bleached with 35 % hydrogen peroxide. The samples were randomly divided into 5 groups based on the antioxidants used. n = 20 Group 1 (Control): No antioxidant agent, Group 2: 10 % SA solution, Group 3: 6.5 % GSE, Group 4: 5 % GTE, Group 5: Er: YAG laser and Group 6: CP. Following reversal, the composite was built and cured for 40 s. All the specimens were stored in distilled water at room temperature for 1 day. Microleakage, SBS, and failure mode were analyzed. Kolmogorov-Smirnov test, one-way analysis of variance, and Tukey's multiple post hoc test were used to analyze the data statistically.

RESULTS

Group 2 (SA) (20.11 ± 5.79 nm) exhibited minimum value of microleakage and highest SBS (10.22 ± 1.62 MPa). Whereas, Group 1 (No antioxidant agent) displayed maximum scores of marginal leakage (28.11±8.89 nm) and lowest SBS (7.02 ± 1.22 MPa).

CONCLUSION

CP, GTE and GSE can be used as a potential alternative to the commonly used SA solution to reverse the negative impact of bleaching on the enamel surface. The use of reversal agents CP, GTE and GSE improves bond values with a decrease in microleakage scores However, future studies are still warranted to conclude the outcomes of the existing study.

Micro Tensile bond strength and microleakage assessment of total-etch and self-etch adhesive bonded to carious affected dentin disinfected with Chlorhexidine, Curcumin, and Malachite green

AIMS AND OBJECTIVES

Assessment of micro tensile bond strength (microTBS) and micro-leakage scores of total-etch adhesive (TAE) and self-etch adhesive (SAE) bonded to carious affected dentin (CAD) sterilized using different cavity disinfectant (curcumin photosensitizer (CP) and malachite green (MG) and Chlorhexidine (CHX) in comparison to no disinfection (ND) control group.

MATERIALS AND METHODS

One hundred and twenty human molars having International Caries Detection and Assessment System (ICDAS) scores of 4 and 5 were included. Visual inspection, dental explorer hardness testing, and caries detector solution using 5% basic Fuchsin dye solution was applied to dentin to identify the CAD surface. All the specimens were divided into four groups (n = 30) according to the cavity disinfectants used. Group A: 2% CHX, Group B: CP, Group C: MG, and Group D: ND. Each group was further divided into two subgroups (n = 15) based on the adhesion protocol. Groups A1, B1, C1, and D1 were held using TEA, and groups A2, B2, C2, and D2 were adhered using SEA system. The composite material was then built in 2 mm increments and then cured with light. MicroTBS and failure mode assessment using a universal testing machine (UTM) and stereomicroscope at a 40X magnification was performed on 10 samples from each subgroup. The microleakage assessment was performed using a dye penetration test on five samples from each group. ANOVA and Tukey post-hoc tests were used to compare means and standard deviation (SD) of bond strength and microleakage (p < 0.05). RESULTS The maximum microTBS was displayed by A1= CHX and TEA (13.28± 1.01 MPa). The lowest bond scores were demonstrated by C2= MG and SEA (5.98±0.44 MPa). The highest micro-leakage was exhibited by C1= MG and TEA (58.32 ± 2.11 nm). Whereas, the lowest micro-leakage values were displayed by A2= CHX and SEA (24.34± 1.11 nm).

CONCLUSION

Chlorohexidiene displayed better bond strength and the lowest microleakage scores with Total-etch adhesive and Self-etch adhesives when used as a cavity disinfectant. Total-etch adhesives performed better in terms of microTBS scores whereas self-etch adhesives displayed superior seal ability within the same disinfectant group.

Dentin disinfection and adhesive bond strength using modified photoactivated carbon nanoparticles

AIMS

The present study aimed to investigate the bond integrity and disinfection efficacy of Methylene blue(MB) alone, MB-PDT (Photodynamic therapy), MB@ carbon nanoparticles (CP)-PDT, and Cr, Cr: YSGG (ECL) against lactobacilli in Caries-affected dentin (CAD) MATERIAL AND METHODS: Methods consisted of Shear bond strength (SBS), Scanning electron microscopy (SEM), energy dispersive X-ray (EDX), methods of disinfection, and failure analysis. CAD samples were prepared and biofilm formed on the specimens randomly allocated into five groups based on disinfection. Group 1: CHX; Group 2: MB; Group 3: MB-PDT: group 4: MB@CP-PDT and group 5: ECL. After disinfection Colony forming units were measured and specimens were restored and positioned under a universal testing machine (UTM). Failure analysis was performed using a stereomicroscope. The difference in survival rate was assessed using the Kruskal-Walis test. Mean and standard deviation for bond values after different methods of disinfection was evaluated using analysis of variance (ANOVA) and Post Hoc Tukey. The significance level was p<0.05 RESULTS: Morphological analysis revealed that CPs under SEM are flat discs with edged irregular shapes. EDX analyses show a spike indicating carbon particles by more than 95%. MB@CP-PDT displayed the highest reduction in lactobacillus levels in comparison to the other disinfection methods. The highest SBS was exhibited by the CAD sample disinfected with ECL. The lowest SBS values in CAD specimens after cavity cleansing with MB alone. The predominant failure type in CAD disinfected with MB alone, ECL CHX, MB-PDT, and MB@CP-PDT was adhesive.

CONCLUSION

The use of MB@CP-PDT showed high antibacterial potency against lactobacillus but demonstrated bond values similar to CHX. Use of Er, Cr: YSGG showed considerable effectiveness against lactobacillus along with the highest bond values.

Incorporation of Zirconium Oxide Nanoparticles in Adhesive Resin for Bonding of Brackets to Enamel Conditioned with Er,Cr:YSGG, Photodynamic Therapy, and Phosphoric Acid

Objective: To evaluate the effect of enamel conditioning methods, that is, total-etch and rinse (TER), Er,Cr:YSGG (ECYL), and photodynamic therapy (PDT) on the shear bond strength (SBS) of orthodontic metallic brackets bonded using Zirconium oxide experimental adhesive (ZOEA). Methods: Sixty human incisor buccal surfaces were cleaned and allocated into three groups based on the method of enamel surface treatment, that is, TER using 37% phosphoric acid gel, methylene blue photosensitizer activated by PDT and ECYL (n = 20 each). Each group was further divided into two subgroups (n = 10) based on the type of adhesive, that is, ZOEA and experimental adhesive (EA). Metallic brackets were seated using composite resin. Samples were placed in a universal testing machine for SBS and failure mode using the ARI index. One-way analysis of variance and post hoc Tukey were used for multiple comparisons. ARI was presented in percentages in different investigated groups. Results: TER+ZOEA (17.16 ± 0.41 MPa) displayed the highest bond integrity. However, group PDT+EA (11.34 ± 0.25 MPa) demonstrated the lowest bond scores. The intergroup comparison revealed that the TER system displayed significantly higher SBS values than the PDT and ECYL groups (p < 0.05). The intragroup comparison revealed that enamel conditioned with TER and brackets bonded with ZOEA and EA displayed comparable bond integrity (p > 0.05). Conclusions: Enamel conditioned with TER bonded to a metallic bracket displayed better bond strength than PDT and ECYL. Zirconium oxide nanoparticles incorporated in adhesive have proved to be promising in improving the bond integrity of adhesive.

Caries-affected dentin disinfection using Triphala, Indocyanine green, and Potassium Titanyl Phosphate laser and their effect on adhesive bond strength

AIM

To assess the impact of new cavity sterilization types using ozone water (OW), Potassium Titanyl Phosphate laser (KTPL), Triphala, and indocyanine green photosensitizer (ICGP) on adhesive bond strength.

MATERIALS AND METHODS

Fifty human permanent molars were included based on the criteria of International Caries Detection and Assessment System (ICDAS) scores 4 and 5 visual examinations, surface hardness valuation, staining by a caries detector solution, and radiographs. Caries-affected dentin (CAD) samples were randomly distributed into groups based on methods of disinfection (n = 10). Group 1: chlorhexidine, group 2: ow, group 3: KTPL, group 4: Triphala, and group 5: ICGP. Following disinfection, specimens were applied with Adper prime and bond NT and then restored with resin composite. All specimens were positioned in a jig of the universal testing machine for shear bond strength (SBS). The debonded samples were analyzed under a stereomicroscope at 40x magnification to determine the type of failure. Analysis of variance (ANOVA) and Tukey HSD tests were used keeping the level of significance p < 0.05.

RESULTS

The highest bond of adhesive resin was displayed by group 2 specimens cleaned using OW (16.71 ± 0.19 MPa). Whereas, the lowest bond integrity was observed by group 5 specimens disinfected using ICGP (11.21 ± 0.16 MPa). It was observed samples disinfected with OW (16.71 ± 0.19 MPa) in group 2 and samples in group 4 (16.09 ± 0.26 MPa) treated with Triphala displayed comparable outcomes of bond strength (p > 0.05). It was observed that group 2 (70%) and 4 (80%) treated specimens accounted mostly for cohesive failure. However, groups 1 (80%), 3 (60%), and 5 (70%) displayed an adhesive failure pattern.

CONCLUSION

OW and Triphala displayed better bond integrity of adhesive resin to CAD and therefore have the potential to be used as a cavity disinfectant in clinical settings. However, ICGP and KTPL displayed weak bonds of adhesive to CAD. More work is needed to extrapolate the findings of the present study.

Influence of contemporary ceramo-metallic crown decontamination on the surface roughness, color stability, and disinfection. An in vitro analysis

AIM

To assess the antimicrobial effects, surface roughness (Ra), and color change (ΔE) of Morinda Citrofolia, Sapindus Mukorossi, Indocyanine green photosensitizer, and 2% NaOCl on metal ceramic crown colonized with C. Albicans, S aureus, S. mutans, and E. coli.

MATERIAL AND METHODS

An aggregate of 40 (n = 10 each) Ni/Cr metal-ceramic crowns were fabricated and inoculated with the American Type Culture Collection (ATCC) of varied microbial colonies colonized by C. Albicans, S aureus, S. mutans, and E. coli. After inoculation, specimens were exposed to four different types of disinfection methods i.e. group 1: MC, group 2: SM, group 3:ICGP, and group 4 2% NaOCl respectively to evaluate antimicrobial efficacy, Ra, and color change. Later, the microbial assay was performed and expressed as CFU/ml (log 10). Ra was assessed using a surface analyzer and color change ΔE was evaluated using a spectrophotometer Statistical analysis was performed by using two-way ANOVA and Post HocTukey's test maintaining a significance level of p less than 0.05.

RESULTS

The highest antimicrobial efficacy for metallic-ceramic crown decontamination against all inspected microbial colonies was unveiled by group 1: MC, whereas the lowest disinfection efficacy was revealed by group 4 sterilized with 2% NaOCl (control). Metallic ceramic crown decontamination with MC and SM substantiated equivalent antimicrobial efficacy in plummeting CFU/mL (log10) of C.Albicans, S aureus, S.mutans, and E. coli (p>0.05). However, ICGP as a crown disinfectant validated antimicrobial efficacy significantly less compared to MC and SM (p<0.05). Ra was assessed post-disinfection with no changes observed (p>0.05) among all groups. Similarly, ΔE was significantly higher in crowns disinfected with ICGP (p<0.05) CONCLUSION: Metallic ceramic crown decontamination using herbal disinfectants Morinda Citrofolia and Sapindus Mukorossi exhibited favorable antimicrobial efficacies against microbial colonies of C. albicans, S aureus, S.mutans, and E. coli with no changes in surface roughness and color.

Effect of Method of Removing Caries-Affected Dentin on the Bond Strength of Composite Resin to Root Canal Dentin

The adhesion of composite resin to caries-affected dentin differs from the adhesion of resin to sound dentin. We evaluated the bond strengths of dual-cure resin composites applied to caries-affected root canal dentin under various clinical conditions and using several caries removal indicators. In the dye stain 1 group, caries were removed to a pale pink stain level using a caries detector. In the dye stain 2 group, caries were removed to a stain-free level using a caries detector. In the probing group, caries were removed to the level of hardness based on probing with a sharp explorer. Additionally, a sound dentin group was used as a control. We compared the resin composite microtensile bond strengths and failure mode distribution among the groups. The bond strengths (MPa) of the probing (64.6 ± 11.9) and the sound dentin (68.7 ± 11.1) groups were significantly higher than those of the dye stain 1 (46.9 ± 7.9) and 2 (47.5 ± 8.4) groups (p < 0.05). The removal of caries-affected dentin using a dentin-hardness-based technique showed higher tensile strength than that using a dye stain technique involving removal to any color level. Thus, the caries removal technique used on root canal dentin affects the bond strength of the resin composite.