Viscoelasticity of single wall carbon nanotube suspensions

Stable dispersion of carbon nanotubes in a molten salt of KNO3-NaNO3-NaNO2-LiNO3-LiOH

Carbon nanotubes (CNTs) have excellent mechanical and electrical properties; however, they suffer from dispersion problems in various applications. Traditional dispersing strategies of CNTs mostly use oxidation with strong acids or mechanical milling with high energy, which causes serious damage to the intrinsic structures and properties of CNTs. Therefore, it is important to develop new methods for dispersing CNTs without destroying their structures. This paper proposes to disperse CNTs in low-temperature molten salts composed of KNO3-NaNO3-NaNO2-LiNO3-LiOH. By adjusting the composition ratio of molten salts and alkaline, the interaction between charged ions and CNT electrons in the molten salt is studied. The alkaline molten salts can stably disperse CNTs and do not destroy their lengths, thereby offering better electric conductivity. This work will provide a new yet effective method for dispersing CNTs with high aspect ratios, which are important for the application of CNTs and other nanocarbons.

Effective medium theory for mechanical phase transitions of fiber networks

Networks of stiff fibers govern the elasticity of biological structures such as the extracellular matrix of collagen. These networks are known to stiffen nonlinearly under shear or extensional strain. Recently, it has been shown that such stiffening is governed by a strain-controlled athermal but critical phase transition, from a floppy phase below the critical strain to a rigid phase above the critical strain. While this phase transition has been extensively studied numerically and experimentally, a complete analytical theory for this transition remains elusive. Here, we present an effective medium theory (EMT) for this mechanical phase transition of fiber networks. We extend a previous EMT appropriate for linear elasticity to incorporate nonlinear effects via an anharmonic Hamiltonian. The mean-field predictions of this theory, including the critical exponents, scaling relations and non-affine fluctuations qualitatively agree with previous experimental and numerical results.

The elastic response of graphene oxide gels as a crumpling phenomenon

The broad spectrum of chemical and electronic properties of 2D nanomaterials makes them attractive in a wide range of applications, especially in the context of printed electronics. Therefore, understanding the rheological properties of nanosheet suspensions is crucial for many additive manufacturing techniques. Here, we study the viscoelastic properties of aqueous suspensions of graphene oxide nanosheets. We show that in the gel phase, the magnitude of the elastic response and its scaling with volume fraction is independent of the lateral size of the particles and the interaction strength between them. We explain this behavior by modelling the elasticity of these gels as a crumpling phenomenon where the magnitude of the response is determined by the bending stiffness and thickness of the sheets. Due to their low bending stiffness these nanosheets crumple upon deformation and may therefore be considered soft colloids. Furthermore, we provide an explanation why the yield strain decreases with packing fraction for these gels.

Advanced cellulose nanocrystals (CNC) and cellulose nanofibrils (CNF) aerogels: Bottom-up assembly perspective for production of adsorbents

The most common and abundant polymer in nature is the linear polysaccharide cellulose, but processing it requires a new approach since cellulose degrades before melting and does not dissolve in ordinary organic solvents. Cellulose aerogels are exceptionally porous (>90 %), have a high specific surface area, and have low bulk density (0.0085 mg/cm³), making them suitable for a variety of sophisticated applications including but not limited to adsorbents. The production of materials with different qualities from the nanocellulose based aerogels is possible thanks to the ease with which other chemicals may be included into the structure of nanocellulose based aerogels; despite processing challenges, cellulose can nevertheless be formed into useful, value-added products using a variety of traditional and cutting-edge techniques. To improve the adsorption of these aerogels, rheology, 3-D printing, surface modification, employment of metal organic frameworks, freezing temperature, and freeze casting techniques were all investigated and included. In addition to exploring venues for creation of aerogels, their integration with CNC liquid crystal formation were also explored and examined to pursue "smart adsorbent aerogels". The objective of this endeavour is to provide a concise and in-depth evaluation of recent findings about the conception and understanding of nanocellulose aerogel employing a variety of technologies and examination of intricacies involved in enhancing adsorption properties of these aerogels.

Chiral Liquid Crystalline Properties of Cellulose Nanocrystals: Fundamentals and Applications

By using an independent self-assembly process that is occasionally controlled by evaporation, cellulose nanocrystals (CNCs) may create films (pure or in conjunction with other materials) that have iridescent structural colors. The self-forming chiral nematic structures and environmental safety of a new class of photonic liquid crystals (LCs), referred to as CNCs and CNC-embedded materials, make them simple to make and treat. The structure of the matrix interacts with light to give structural coloring, as opposed to other dye pigments, which interact with light by adsorption and reflection. Understanding how CNC self-assembly constructs structures is vital in several fields, including physics, science, and engineering. To constructure this review, the colloidal characteristics of CNC particles and their behavior during the formation of liquid crystals and gelling were studied. Then, some of the recognized applications for these naturally occurring nanoparticles were summarized. Different factors were considered, including the CNC aspect ratio, surface chemistry, concentration, the amount of time needed to produce an anisotropic phase, and the addition of additional substances to the suspension medium. The effects of alignment and the drying process conditions on structural changes are also covered. The focus of this study however is on the optical properties of the films as well as the impact of the aforementioned factors on the final transparency, iridescent colors, and versus the overall response of these bioinspired photonic materials. Control of the examined factors was found to be necessary to produce reliable materials for optoelectronics, intelligent inks and papers, transparent flexible support for electronics, and decorative coatings and films.

Shear-induced phase transition and critical exponents in three-dimensional fiber networks

When subject to applied strain, fiber networks exhibit nonlinear elastic stiffening. Recent theory and experiments have shown that this phenomenon is controlled by an underlying mechanical phase transition that is critical in nature. Growing simulation evidence points to non-mean-field behavior for this transition and a hyperscaling relation has been proposed to relate the corresponding critical exponents. Here, we report simulations on two distinct network structures in three dimensions. By performing a finite-size scaling analysis, we test hyperscaling and identify various critical exponents. From the apparent validity of hyperscaling, as well as the non-mean-field exponents we observe, our results suggest that the upper critical dimension for the strain-controlled phase transition is above three, in contrast to the jamming transition that represents another athermal, mechanical phase transition.

Effect of carbon nanotube doping on the energy dissipation and rate dependent deformation behavior of polyurethane foams

An experimental investigation is performed to characterize the effect of carbon nanotubes on the average mechanical properties of polyurethane foams. Polyurethane foams are doped with as-grown and oxidized carbon nanotubes at varying carbon nanotube concentrations. It is observed that the inclusion of carbon nanotubes up to a threshold concentration decreases the density of freely expanding polyurethane foams. Uniaxial and cyclic compression testing of foam samples is carried out to study their energy dissipation and rate dependent deformation behavior. While energy dissipation is observed to be higher in neat polyurethane foams, carbon nanotube reinforced foams show better recovery when compressed beyond elastic limit due to their stiffer foam cell walls. It is shown that incorporation of oxidized carbon nanotubes should be preferred over as grown carbon nanotubes to improve flexural, thermal and acoustic response of polyurethane foams. Scanning electron microscopy analysis of compressed samples reveals that cell shearing; cell bending and fracture at nodes are the predominant mode of deformation in all foam samples.

Three-Dimensional Monolithic Organic Battery Electrodes

Design of freestanding electrodes incorporated with redox-active organic materials has been limited by the poor intrinsic electrical conductivity and lack of methodology driving the feasible integration of conductive substrate and the organic molecules. Single-walled carbon nanotube (SWCNT) aerogels, which possess continuous network structure and high surface area, offer a three-dimensional electrically conducting scaffold. Here, we fabricate monolithic organic electrodes by coating a nanometer-scale imide-based network (IBN) that possesses abundant redox-active sites on the 3D SWCNT scaffold. The substantially integrated 3D monolithic organic electrodes sustain high electrical conductance through a 3D electronic pathway in their compressed form (∼21 μm). A thin and controllable layer (<8 nm) of IBN organic materials has a strong adhesion onto the ultra-lightweight and conductive substrate and facilitates multielectron redox reactions to deliver a specific capacity of up to 1550 mA h g^-1 (corresponding to the areal capacity of ∼2.8 mA h cm^-2). The redox-active IBN in synergy with the 3D SWCNT scaffold can enable superior electrochemical performances compared to the previously reported organic-based electrode architectures and inorganic-based electrodes.

Exclusion and Trapping of Carbon Nanostructures in Nonisotropic Suspensions of Cellulose Nanostructures

Incorporation of carbon nanotubes (CNTs) into liquid crystalline phases of cellulose nanocrystals (CNCs) may be used for preparation of hybrids with novel optical, electrical, and mechanical properties. Here, we investigated the effect of nanoparticle diameter, geometry, aspect ratio, and flexibility on the exclusion of dispersed carbon nanostructures (CNs) from the chiral nematic phase (N*) of the CNCs. Although the CNs are nicely dispersed in isotropic suspensions of CNCs, we observe that fullerenes, carbon black, and CNTs are depleted from the N* phase. This observation is surprising as theoretical predictions and previous observations of nanoparticles indicate that nanometric inclusions would be incorporated within the N* phase. Cryogenic transmission electron microscopy imaging reveals that the dispersed CNs induce misorientation of the CNCs, irrespective of their geometry and size. Rheological measurements suggest that about 10% of the CNCs are affected by the CNs. The multiparticle nature of the interaction may be the origin of the nonsize selective exclusion of the CNs. Re-entrant behavior is observed at high CNC concentrations (about 13 wt %), where a (nematic) gel-like phase kinetically traps the CNs. These phases exhibit non-Newtonian flow behavior and birefringence, offering a pathway for preparation of nonisotropic CNCs-CNT composites and thin films via liquid processing.

Effects of particle stiffness on the extensional rheology of model rod-like nanoparticle suspensions

The linear and nonlinear rheological behavior of two rod-like particle suspensions as a function of concentration is studied using small amplitude oscillatory shear, steady shear and capillary breakup extensional rheometry. The rod-like suspensions are composed of fd virus and its mutant fdY21M, which are perfectly monodisperse, with a length on the order of 900 nm. The particles are semiflexible yet differ in their persistence length. The effect of stiffness on the rheological behavior in both, shear and extensional flow, is investigated experimentally. The linear viscoelastic shear data is compared in detail with theoretical predictions for worm-like chains. The extensional properties are compared to Batchelor's theory, generalized for the shear thinning nature of the suspensions. Theoretical predictions agree well with the measured complex moduli at low concentrations as well as the nonlinear shear and elongational viscosities at high flow rates. The results in this work provide guidelines for enhancing the elongational viscosity based on purely frictional effects in the absence of strong normal forces which are characteristic for high molecular weight polymers.

Aqueous dispersions of carbon black and its hybrid with carbon nanofibers

The aqueous dispersions of a special type of carbon black (CB) in 1 M lithium bis(trifluoromethanesulfonimide) electrolyte is mainly controlled by the affinity of the aqueous electrolyte towards the CB particles rather than the particle size. In spite of its small particle size (30 nm), this type of CB forms a three-dimensional open network which is rheologically and electrically percolated at a relatively high threshold (2.0 wt%) with enhanced rheological and electrical properties. At this percolating threshold, replacing a trace amount of CB with equivalent carbon nanofibers (CNFs) produces hybrid dispersions with higher electrical conductivity and comparable rheological behavior to pure CB dispersions. This hybrid dispersion is dominated by a cooperatively supporting network, which is wired by the flexible filamentous nanofibers so that it is able to recover the conductivity loss under flow conditions due to flow-induced breaking up of the conductive pathways of CB and presumably sustain a higher load of active materials. This finding suggests hybrid dispersions as a promising precursor in the formulation of electrode suspensions for aqueous semi-solid redox flow cells.

Optimal hybrid dispersion of carbon black (CB) and nanofibers (CNFs) is formed at a critical content of CNFs before its aggregation concentration so that CNFs wire CB aggregates to recover the conductivity loss without increasing of CB rigidity.

Drastically Enhancing Moduli of Graphene-Coated Carbon Nanotube Aerogels via Densification while Retaining Temperature-Invariant Superelasticity and Ultrahigh Efficiency

Lightweight open-cell foams that are simultaneously superelastic, possess exceptionally high Young's moduli (Y), exhibit ultrahigh efficiency, and resist fatigue as well as creep are particularly desirable as structural frameworks. Unfortunately, many of these features are orthogonal in foams of metals, ceramics, and polymers, particularly under large temperature variations. In contrast, foams of carbon allotropes including carbon nanotubes and graphene developed over the past few years exhibit these desired properties but have low Y due to low density, ρ = 0.5-10 mg/mL. Densification of these foams enhances Y although below expectation and also dramatically degrades other properties because of drastic changes in microstructure. We have recently developed size- and shape-tunable graphene-coated single-walled carbon nanotube (SWCNT) aerogels that display superelasticity at least up to a compressive strain (ε) = 80%, fatigue and creep resistance, and ultrahigh efficiency over -100-500 °C. Unfortunately, Y of these aerogels is only ∼0.75 MPa due to low ρ ≈ 14 mg/mL, limiting their competitiveness as structural foams. We report fabrication of similar aerogels but with ρ spanning more than an order of magnitude from 16-400 mg/mL through controlled isostatic compression in the presence of a polymer coating circumventing any microstructural changes in stark contrast to other foams of carbon allotropes. The compressive stress (σ) versus ε measurements show that the densification of aerogels from ρ ≈ 16 to 400 mg/mL dramatically enhances Y from 0.9 to 400 MPa while maintaining superelasticity at least up to ε = 10% even at the highest ρ. The storage (E') and loss (E″) moduli measured in the linear regime show ultralow loss coefficient, tan δ = E″/E' ≈ 0.02, that remains constant over three decades of frequencies (0.628-628 rad/s), suggesting unusually high frequency-invariant efficiency. Furthermore, these aerogels retain exceptional fatigue resistance for 10⁶ loading-unloading cycles to ε = 2% and creep resistance for at least 30 min under σ = 0.02 MPa with ρ = 16 mg/mL and σ = 2.5 MPa with higher ρ = 400 mg/mL. Lastly, these robust mechanical properties are stable over a broad temperature range of -100-500 °C, motivating their use as highly efficient structural components in environments with extreme temperature variations.

Formation of Colloidal Nanocellulose Glasses and Gels

Nanocellulose (NC) suspensions can form rigid volume-spanning arrested states (VASs) at very low volume fractions. The transition from a free-flowing dispersion to a VAS can be the result of either an increase in particle concentration or a reduction in interparticle repulsion. In this work, the concentration-induced transition has been studied with a special focus on the influence of the particle aspect ratio and surface charge density, and an attempt is made to classify these VASs. The results show that for these types of systems two general states can be identified: glasses and gels. These NC suspensions had threshold concentrations inversely proportional to the particle aspect ratio. This dependence indicates that the main reason for the transition is a mobility constraint that, together with the reversibility of the transition, classifies the VASs as colloidal glasses. If the interparticle repulsion is reduced, then the glasses can transform into gels. Thus, depending on the preparation route, either soft and reversible glasses or stiff and irreversible gels can be formed.

Creep- and fatigue-resistant, rapid piezoresistive responses of elastomeric graphene-coated carbon nanotube aerogels over a wide pressure range

Lightweight, flexible piezoresistive materials with wide operational pressure ranges are in demand for applications such as human physical activity and health monitoring, robotics, and for functional interfacing between living systems and wearable electronics. Piezoresistivity of many elastomeric foams of polymers and carbon allotropes satisfies much of the required characteristics for these applications except creep and fatigue resistance due to their viscoelasticity, critically limiting the reliability and lifetime of integrated devices. We report the piezoresistive responses from aerogels of graphene-coated single-walled carbon nanotubes (SWCNTs), made using a facile and versatile sol-gel method. Graphene crosslinks the junctions of the underlying random network of SWCNTs, generating lightweight elastomeric aerogels with a mass density of ≈11 mg mL^-1 (volume fraction ≈7.7 × 10^-3) and a Young's modulus of ≈0.4 MPa. The piezoresistivity of these aerogels spans wide compressive pressures up to at least 120 kPa with sensitivity that exhibit ultrafast temporal responses of <27 ms and <3% delay ratio over 10⁴ compressive loading-unloading cycles at rates between 0.1-10 Hz. Most importantly, the piezoresistive responses do not show any creep at least for 1 hour and 80 kPa of compressive static loading. We suggest that the fatigue- and creep-resistant, ultrafast piezoresistive responses of these elastomeric aerogels are highly attractive for use in dynamic and static lightweight, pressure sensing applications such as human activity monitoring and soft robotics.

Shear-Induced Breakup of Cellulose Nanocrystal Aggregates

The flow properties of two kinds of cellulose nanocrystal (CNC) rods with different aspect ratios and similar zeta potentials in aqueous suspensions have been investigated. The aqueous CNC suspensions undergo a direct transition from dilute solution to colloidal glass instead of phase separation with the increasing CNC concentration. The viscosity profile shows a single shear-thinning behavior over the whole range of shear rates investigated. The shear-thinning behavior becomes stronger with the increasing CNC concentration. The viscosity is much higher for the unsonicated suspension when compared with the sonicated suspensions. The CNC rods appear arrested without alignment with an increasing shear rate from the small-angle light scattering patterns. The arrested glass state results from electric double layers surrounding the CNC rods, which give rise to long-ranged repulsive interactions. For the first time, we demonstrate that, within a narrow range of CNC concentrations, a shear-induced breakup process of the CNC aggregates exists when the shear rate is over a critical value and that the process is reversible in the sense that the aggregates can be reformed. We discuss the competition between the shear-induced breakup and the concentration-driven aggregation based on the experimental observations. The generated aggregate structure during the breakup process is characterized by a fractal dimension of 2.41. Furthermore, we determine two important variables-the breakup rate and the characteristic aggregate size-and derive analytical expressions for their evolution during the breakup process. The model predictions are in quantitative agreement with the experimental results.

Distribution of single wall carbon nanotubes in the Xenopus laevis embryo after microinjection

Single wall carbon nanotubes (SWCNTs) are advanced materials with the potential for a myriad of diverse applications, including biological technologies and large-scale usage with the potential for environmental impacts. SWCNTs have been exposed to developing organisms to determine their effects on embryogenesis, and results have been inconsistent arising, in part, from differing material quality, dispersion status, material size, impurity from catalysts and stability. For this study, we utilized highly purified SWCNT samples with short, uniform lengths (145 ± 17 nm) well dispersed in solution. To test high exposure doses, we microinjected > 500 µg ml(-1) SWCNT concentrations into the well-established embryogenesis model, Xenopus laevis, and determined embryo compatibility and subcellular localization during development. SWCNTs localized within cellular progeny of the microinjected cells, but were heterogeneously distributed throughout the target-injected tissue. Co-registering unique Raman spectral intensity of SWCNTs with images of fluorescently labeled subcellular compartments demonstrated that even at regions of highest SWCNT concentration, there were no gross alterations to subcellular microstructures, including filamentous actin, endoplasmic reticulum and vesicles. Furthermore, SWCNTs did not aggregate and localized to the perinuclear subcellular region. Combined, these results suggest that purified and dispersed SWCNTs are not toxic to X. laevis animal cap ectoderm and may be suitable candidate materials for biological applications.

High visible-light photochemical activity of titania decorated on single-wall carbon nanotube aerogels

Titania decorated on single-wall carbon nanotube aerogels degraded organic dyes under visible-light irradiation at ultrahigh rates.

Gelation and mechanical response of patchy rods

We perform Brownian dynamics simulations to study the gelation of suspensions of attractive, rod-like particles. We show that in detail the rod-rod surface interactions can dramatically affect the dynamics of gelation and the structure and mechanics of the networks that form. If the attraction between the rods is perfectly smooth along their length, they will collapse into compact bundles. If the attraction is sufficiently corrugated or patchy, over time, a rigid space-spanning network will form. We study the structure and mechanical properties of the networks that form as a function of the fraction of the surface, f, that is allowed to bind. Surprisingly, the structural and mechanical properties are non-monotonic in f. At low f, there are not a sufficient number of cross-linking sites to form networks. At high f, rods bundle and form disconnected clusters. At intermediate f, robust networks form. The elastic modulus and yield stress are both non-monotonic in the surface coverage. The stiffest and strongest networks show an essentially homogeneous deformation under strain with rods re-orienting along the extensional axis. Weaker, more clumpy networks at high f re-orient relatively little with strong non-affine deformation. These results suggest design strategies for tailoring surface interactions between rods to yield rigid networks with optimal mechanical properties.

Stretchable and transparent electrodes based on in-plane structures

Stretchable electronics has attracted great interest with compelling potential applications that require reliable operation under mechanical deformation. Achieving stretchability in devices, however, requires a deeper understanding of nanoscale materials and mechanics beyond the success of flexible electronics. In this regard, tremendous research efforts have been dedicated toward developing stretchable electrodes, which are one of the most important building blocks for stretchable electronics. Stretchable transparent thin-film electrodes, which retain their electrical conductivity and optical transparency under mechanical deformation, are particularly important for the favourable application of stretchable devices. This minireview summarizes recent advances in stretchable transparent thin-film electrodes, especially employing strategies based on in-plane structures. Various approaches using metal nanomaterials, carbon nanomaterials, and their hybrids are described in terms of preparation processes and their optoelectronic/mechanical properties. Some challenges and perspectives for further advances in stretchable transparent electrodes are also discussed.

Molecular control of stress transmission in the microtubule cytoskeleton

In this article, we will summarize recent progress in understanding the mechanical origins of rigidity, strength, resiliency and stress transmission in the MT cytoskeleton using reconstituted networks formed from purified components. We focus on the role of network architecture, crosslinker compliance and dynamics, and molecular determinants of single filament elasticity, while highlighting open questions and future directions for this work.

Macroscopic Carbon Nanotube-based 3D Monoliths

Carbon nanotubes (CNTs) are one of the most promising carbon allotropes with incredible diverse physicochemical properties, thereby enjoying continuous worldwide attention since their discovery about two decades ago. From the point of view of practical applications, assembling individual CNTs into macroscopic functional and high-performance materials is of paramount importance. For example, multiscaled CNT-based assemblies including 1D fibers, 2D films, and 3D monoliths have been developed. Among all of these, monolithic 3D CNT architectures with porous structures have attracted increasing interest in the last few years. In this form, theoretically all individual CNTs are well connected and fully expose their surfaces. These 3D architectures have huge specific surface areas, hierarchical pores, and interconnected conductive networks, resulting in enhanced mass/electron transport and countless accessible active sites for diverse applications (e.g. catalysis, capacitors, and sorption). More importantly, the monolithic form of 3D CNT assemblies can impart additional application potentials to materials, such as free-standing electrodes, sensors, and recyclable sorbents. However, scaling the properties of individual CNTs to 3D assemblies, improving use of the diverse, structure-dependent properties of CNTs, and increasing the performance-to-cost ratio are great unsolved challenges for their real commercialization. This review aims to provide a comprehensive introduction of this young and energetic field, i.e., CNT-based 3D monoliths, with a focus on the preparation principles, current synthetic methods, and typical applications. Opportunities and challenges in this field are also presented.

Yielding and flow of highly concentrated, few-layer graphene suspensions

For a wide range of applications of graphene suspensions, a thorough understanding of their rheological properties is crucial. We probe the microstructure of dense suspensions of micron-sized, few-layer, defect-free graphene platelets by measuring their viscoelastic properties at various concentrations up to 39 mg ml(-1). We propose a model to relate the yield strain to the mesh size of the microstructure as a function of volume fraction ϕ. From the yield stress measurements we infer the typical bond energy (≈20 kBT) and ϕ dependence of the bond number density. These results allow us to express the steady shear viscosity for Peclet number Pe < 10 in terms of the platelet dimensions, bond energy and ϕ using a relaxation ansatz.

Preformed nanoporous carbon nanotube scaffold-based multifunctional polymer composites

Multifunctional polymer nanocomposites that simultaneously possess high modulus and strength, high thermal stability, novel optical responses, and high electrical and thermal conductivity have been actively researched. Carbon nanotubes are considered an ideal additive for composites because of their superlative physical, electronic and optical properties. While nanotubes have successfully added electrical conductivity, thermal stability, and novel optical responses to polymers, mechanical reinforcements, although substantial, have been well below any theoretical estimations. Here, we integrated preformed hydrogels and aerogels of individually dispersed nanotubes with polymer to increase elastic modulus of composites according to Halpin-Tsai model up to at least 25 vol % of nanotubes. Our solution-based fabrication method allowed us to create bulk composites with tunable form-factors, and with polymers that were incompatible with nanotubes. Further, in this approach, nanotubes were not covalently linked among themselves and to the polymer, so intrinsic optical, electrical, and thermal properties of nanotubes could be exploited. The optically active nanotubes, for example, added a strain-dependent, spatially resolved fluorescence to these composites. Finally, the nanoporous nanotube networks suppressed the polymer glass transition and extended the mechanical integrity of polymer well above its polymer melting point, and both the nanotubes and polymer remained thermally stable above their decomposition temperatures.

Ultracompressible, high-rate supercapacitors from graphene-coated carbon nanotube aerogels

Emerging applications for electrochemical energy storage require devices that not only possess high power and energy, but also are capable of withstanding mechanical deformation without degradation of performance. To this end, we have constructed electric double layer capacitors (EDLCs), also referred to as supercapacitors, using thick, ultracompressible graphene-coated carbon nanotube aerogels as electrodes. These electrodes showed a high capacitance in both aqueous and room-temperature ionic liquid (RTIL) electrolytes, achieving between 60 and100 F/g, respectively, with the performance stable over hundreds of charge/discharge cycles and at high rates exceeding 1 V/s. This performance was retained fully under 90% compression of the systems, allowing us to construct cells with high volumetric capacitances of ∼5-18 F/cm(3) in aqueous and RTIL electrolytes, respectively, which are 50-100 times higher than comparable compressible EDLCs (∼0.1 F/cm(3)). Further, the volumetric capacitances approach values reported for compressible pseudocapacitors (∼15-30 F/cm(3)) but without the degraded lifetime and reversibility that typically plague compressible pseudocapacitors. The electrodes demonstrated largely strain-invariant ion transport with no change in capacitance and high-rate performance even at 90% compressive strain. This material serves as an excellent platform for exploring the possibility for use of extremely compressible EDLCs with negligible degradation in capacitance in applications such as electric vehicles and wearable electronics.

Membrane/mediator-free rechargeable enzymatic biofuel cell utilizing graphene/single-wall carbon nanotube cogel electrodes

Enzymatic biofuel cells (EBFCs) utilize enzymes to convert chemical energy present in renewable biofuels into electrical energy and have shown much promise in the continuous powering of implantable devices. Currently, however, EBFCs are greatly limited in terms of power and operational stability with a majority of reported improvements requiring the inclusion of potentially toxic and unstable electron transfer mediators or multicompartment systems separated by a semipermeable membrane resulting in complicated setups. We report on the development of a simple, membrane/mediator-free EBFC utilizing novel electrodes of graphene and single-wall carbon nanotube cogel. These cogel electrodes had large surface area (∼ 800 m(2) g(-1)) that enabled high enzyme loading, large porosity for unhindered glucose transport and moderate electrical conductivity (∼ 0.2 S cm(-1)) for efficient charge collection. Glucose oxidase and bilirubin oxidase were physically adsorbed onto these electrodes to form anodes and cathodes, respectively, and the EBFC produced power densities up to 0.19 mW cm(-2) that correlated to 0.65 mW mL(-1) or 140 mW g(-1) of GOX with an open circuit voltage of 0.61 V. Further, the electrodes were rejuvenated by a simple wash and reloading procedure. We postulate these porous and ultrahigh surface area electrodes will be useful for biosensing applications, and will allow reuse of EBFCs.

Suspensions of carbon nanofibers in organic medium: rheo-electrical properties

The nonaqueous suspensions of carbon nanofibers (CNFs) in 1 M lithium bis(trifluoromethanesulfonaimide) in propylene carbonate electrolyte reveal unique structural evolution and shear-induced transition due to the high aspect ratio.

Amphoteric hyperbranched polymers with multistimuli-responsive behavior in the application of polymer flooding

Amphoteric hyperbranched polymers (AMHPMs) that respond to shear rate, temperature, salt, and pH were synthesized using a water free radical polymerization technique.

Flow-induced structure and rheological properties of multiwall carbon nanotube/polydimethylsiloxane composites

The structure and normal stress differences of MWNT/polymer composites are influenced by the molecular weight of the polymer matrix and the confinement effect.

Rheology of polymer carbon nanotubes composites

In this review paper the rheology of polymer nanocomposites with dispersed carbon nanotubes is presented. The major factors controlling the rheology of these nanocomposites are the overall concentration of the nanotubes and their state of dispersion. Percolation of anisotropic nanotubes and the transition from isotropic to nematic structures bound the range of concentrations over which the rheological properties of these nanocomposites is dominated by the meso-scale structure and dispersion and are of significance to the processing of nanotube based polymer nanocomposites. The percolation threshold and the concentration for the isotropic to nematic transition are strong functions of the inverse of the effective aspect ratio of the dispersed nanotubes and therefore restrict the range of concentrations over which such nanocomposites can be deployed. In this review we briefly describe the rheology in the dilute regime, where especially for the case of polymer nanocomposites the rheology is dominated by that of the polymer. Subsequently, the percolation phenomenon and rheological significances are presented. Finally, both linear and non-linear rheologies of semi-dilute dispersions with random orientation of nanotubes are discussed in detail. Where possible, the rheological responses are contextualized through the underlying structure of the nanocomposites and interplay of different forces.

Effects of non-linearity on cell-ECM interactions

Filamentous biopolymers such as F-actin, vimentin, fibrin and collagen that form networks within the cytoskeleton or the extracellular matrix have unusual rheological properties not present in most synthetic soft materials that are used as cell substrates or scaffolds for tissue engineering. Gels formed by purified filamentous biopolymers are often strain stiffening, with an elastic modulus that can increase an order of magnitude at moderate strains that are relevant to cell and tissue deformation in vivo. This review summarizes some experimental studies of non-linear rheology in biopolymer gels, discusses possible molecular mechanisms that account for strain stiffening, and explores the possible relevance of non-linear rheology to the interactions between cell and extracellular matrices.