A 1 MHz Miniaturized Electrical Impedance Tomography System for Prostate Imaging

Progressive Approaches in Oncological Diagnosis and Surveillance: Real-Time Impedance-Based Techniques and Advanced Algorithms

Cancer remains a formidable global health challenge, necessitating the development of innovative diagnostic techniques capable of early detection and differentiation of tumor/cancerous cells from their healthy counterparts. This review focuses on the confluence of advanced computational algorithms with noninvasive, label-free impedance-based biophysical methodologies-techniques that assess biological processes directly without the need for external markers or dyes. This review elucidates a diverse array of state-of-the-art impedance-based technologies, illuminating distinct electrical signatures inherent to cancer vs healthy tissues. Additionally, the study probes the transformative potential of these diagnostic modalities in recalibrating personalized cancer treatment paradigms. These modalities offer real-time insights into tumor dynamics, paving the way for precision-guided therapeutic interventions. By emphasizing the quest for continuous in vivo monitoring, these techniques herald a pivotal advancement in the overarching endeavor to combat cancer globally.

Flexi-EIT: A Flexible and Reconfigurable Active Electrode Electrical Impedance Tomography System

Electrical Impedance Tomography (EIT) systems have shown great promise in many fields such as real-time wearable healthcare imaging, but their fixed number of electrodes and placement locations limit the system's flexibility and adaptability for further advancement. In this article, we propose a flexible and reconfigurable EIT system (Flexi-EIT) based on digital active electrode (DAE) architecture to address these limitations. By integrating a reconfigurable number of up to 32 replaceable DAEs into the flexible printed circuit (FPC) based wearable electrode belt, we can enable rapid, reliable, and easy placement while maintaining high device flexibility and reliability. We also explore hardware-software co-optimization image reconstruction solutions to balance the size and accuracy of the model, the power consumption, and the real-time latency. Each DAE is designed using commercial chips and fabricated on a printed circuit board (PCB) measuring 13.1 mm × 24.4 mm and weighing 2 grams. In current excitation mode, it can provide programmable sinusoidal current signal output with frequencies up to 100 kHz and amplitudes up to 1 mA p-p that meets IEC 60601-1 standard. In voltage acquisition mode, it can pre-amplify, filter, and digitize the external response voltage signal, improving the robustness of the system while avoiding the need for subsequent analog signal processing circuits. Measured results on a mesh phantom demonstrate that the Flexi-EIT system can be easily configured with different numbers of DAEs and scan patterns to provide EIT measurement frames at 38 fps and real-time EIT images with at least 5 fps, showing the potential to be deployed in a variety of application scenarios and providing the optimal balance of system performance and hardware resource usage solutions.

A low-cost, portable 32-channel EIT system with four rings based on AFE4300 for body composition analysis

A proposed low-cost, portable, 32-channel (4 rings of 8-channel) Electrical Impedance Tomography (EIT) system based on the AFE4300 analog front-end for body composition measurement. Each ring allows obtaining the conductivity distribution of 4 cross sections, 4 cm apart; to analyze the behavior of conductivity in a volume. The switching of the 4 rings and the current injection and voltage measurement patterns are done with three Texas Instruments 74HC4067 multiplexers, which are managed by an ESP32 board. The proposed system has an average signal-to-noise ratio of 74.71 dB and a frame rate of 50 fps. The sensitivity tests to impedance and volume changes consisted of introducing 4 tubes of different diameters (2 steel and 2 polyvinyl chloride) into a tank with saline solution; then conductivity distribution images were generated in 4 cross-sections of the tank, using the algorithms Gauss-Newton and Noser. Finally, the global impedance index (GI) is calculated to estimate the volume of each tube inside the tank. The results show that the proposed system is highly sensitive to impedance and volume changes, being a promising system for monitoring tissues, and fluids biological.

Robust electrical impedance tomography for biological application: A mini review

Electrical impedance tomography (EIT) has been used by researchers across several areas because of its low-cost and no-radiation properties. Researchers use complex conductivity in bioimpedance experiments to evaluate changes in various indicators within the image target. The diverse volumes and edges of biological tissues and the large impedance range impose dedicated demands on hardware design. The EIT hardware with a high signal-to-noise ratio (SNR), fast scanning and suitable for the impedance range of the image target is a fundamental foundation that EIT research needs to be equipped with. Understanding the characteristics of this technique and state-of-the-art design will accelerate the development of the robust system and provide a guidance for the superior performance of next-generation EIT. This review explores the hardware strategies for EIT proposed in the literature.

Characteristics and topic trends on electrical impedance tomography hardware publications

Objective: Electrical impedance tomography (EIT) is a technique to measure electrical properties of tissue. With the progress of modern integrated circuits and microchips, EIT instrumentation becomes an active research area to improve all aspects of device performance. Plenty of studies on EIT hardware have been presented in prestigious journals. This study explores publications on EIT hardware to identify the developing hotspots and trends. Method: Publications covering EIT hardware on the Web of Science Core Collection (WoSCC) database from 1989 to 2021 were collected for bibliometric analysis. CiteSpace and VOS viewer were used to study the characteristics of the publications. Main results: A total of 592 publications were analyzed, showing that the number of annual publications steadily increased. China, England, and South Korea were the most prolific countries on EIT hardware publications with productive native institutions and authors. Research topics spread out in "bio-electrical impedance imaging", "hardware optimization", "algorithms" and "clinical applications" (e.g., tissue, lung, brain, and oncology). Hardware research in "pulmonary" and "hemodynamic" applications focused on monitoring and were represented by silhouette recognition and dynamic imaging while research in "tumor and tissue" and "brain" applications focused on diagnosis and were represented by optimization of precision. Electrode development was a research focus through the years. Imaging precision and bioavailability of hardware optimization may be the future trend. Conclusion: Overall, system performance, particularly in the areas of system bandwidth and precision in applications may be the future directions of hardware research.

FPGA-Based Processor for Continual Capacitive-Coupling Impedance Spectroscopy and Circuit Parameter Estimation

In principle, the recently proposed capacitive-coupling impedance spectroscopy (CIS) has the capability to acquire frequency spectra of complex electrical impedance sequentially on a millisecond timescale. Even when the measured object with time-varying unknown resistance R_x is capacitively coupled with the measurement electrodes with time-varying unknown capacitance C_x, CIS can be measured. As a proof of concept, this study aimed to develop a prototype that implemented the novel algorithm of CIS and circuit parameter estimation to verify whether the frequency spectra and circuit parameters could be obtained in milliseconds and whether time-varying impedance could be measured. This study proposes a dedicated processor that was implemented as field-programmable gate arrays to perform CIS, estimate R_x and C_x, and their digital-to-analog conversions at a certain time, and to repeat them continually. The proposed processor executed the entire sequence in the order of milliseconds. Combined with a front-end nonsinusoidal oscillator and interfacing circuits, the processor estimated the fixed R_x and fixed C_x with reasonable accuracy. Additionally, the combined system with the processor succeeded in detecting a quick optical response in the resistance of the cadmium sulfide (CdS) photocell connected in series with a capacitor, and in reading out their resistance and capacitance independently as voltages in real-time.

A Polar-Demodulation-Based Impedance-Measurement IC Using Frequency-Shift Technique With Low Power Consumption and Wide Frequency Range

In this paper, we present a new impedance measurement integrated circuit (IC) for achieving a wideband coverage up to 10 MHz and low power consumption. A frequency-shift technique is applied to down-shift the input frequency, which ranges from 100 kHz to 10 MHz, into an intermediate frequency of 10 kHz, while the frequency-shifting is bypassed when the input frequency falls in the range from 100 Hz to 100 kHz. It results in 100 times relaxation of the requirement on the instrumentation amplifier (IA) bandwidth and the comparator delay, greatly reducing overall power consumption. The proposed IC employs the polar demodulation structure with a reference resistor that provides reference timing information avoiding any synchronization issue with the transmitter. In order to compensate for the comparator delay and nonlinearity of the IA, the reference magnitude measurement path is added, making only the mismatch of the circuit affects the accuracy. This allows for employing the auto-zeroing technique that can remove the offset but increase the absolute delay by using an additional capacitor to the comparator. The chip fabricated in a 0.18- μm CMOS technology consumes the power of 756 μW while covering the measurement frequency range from 100 Hz to 10 MHz and exhibiting the maximum magnitude and phase errors of 1.1 % and 1.9 ^°, respectively.

An efficient Point-Matching Method-of-Moments for 2D and 3D Electrical Impedance Tomography Using Radial Basis functions

AbstractObjective: The inverse problem of computing conductivity distributions in 2D and 3D objects interrogated by low frequency electrical signals, which is called Electrical Impedance Tomography (EIT), is treated using a Method-of-Moment technique.

METHODS

A Point-Matching-Method-of-Moment technique is used to formulate a global integral equation solver. Radial Basis Functions are adopted to express the conductivity distribution. Single-step quadratic-norm (L2) and iterative total variation (L1) regularization techniques are exploited to solve the inverse problem.

RESULTS

Simulation and experimental tests on a circular reconstruction domain show satisfactory performance in deriving conductivity distribution, achieving a Correlation Coefficient (CC) up to 0:863 for 70 dB voltage SNR and 0:842 for 40 dB voltage SNR. The proposed methodology with L2-norm regularization provided better results than traditional iterative Gauss-Newtons approach, whereas with L1-norm regularization it showed promising performance. Moreover, 3D reconstructions on a cylindrical cavity demonstrated superior results near the electrodes planes compared to those of the conventional linearized approach. Finally, application to EIT medical data for dynamic lung imaging successfully revealed the breath-cycle conductivity changes.

CONCLUSION

The results show that the proposed method can be effective for both 2D and 3D EIT and applicable to many applications.

SIGNIFICANCE

Strong conductivity variations are successfully tackled with a very good Correlation Coefficient. In contrast to conventional EIT solutions based on weak-form and linearization on small conductivity changes, the proposed method requires only one step to converge with L2-norm regularization. The proposed method with L1-norm regularization also achieves good reconstruction quality with a low number of iterations.

Evaluation of Thoracic Equivalent Multiport Circuits Using an Electrical Impedance Tomography Hardware Simulation Interface

Electrical impedance tomography is a low-cost, safe, and high temporal resolution medical imaging modality which finds extensive application in real-time thoracic impedance imaging. Thoracic impedance changes can reveal important information about the physiological condition of patients’ lungs. In this way, electrical impedance tomography can be a valuable tool for monitoring patients. However, this technique is very sensitive to measurement noise or possible minor signal errors, coming from either the hardware, the electrodes, or even particular biological signals. Thus, the design of a good performance electrical impedance tomography hardware setup which properly interacts with the tissue examined is both an essential and a challenging concept. In this paper, we adopt an extensive simulation approach, which combines the system’s analogue and digital hardware, along with equivalent circuits of 3D finite element models that represent thoracic cavities. Each thoracic finite element model is created in MATLAB based on existing CT images, while the tissues’ conductivity and permittivity values for a selected frequency are acquired from a database using Python. The model is transferred to a multiport RLC network, embedded in the system’s hardware which is simulated at LT SPICE. The voltage output data are transferred to MATLAB where the electrical impedance tomography signal sampling and digital processing is also simulated. Finally, image reconstructions are performed in MATLAB, using the EIDORS library tool and considering the signal noise levels and different electrode and signal sampling configurations (ADC bits, sampling frequency, number of taps).

Analog Realization of Fractional-Order Skin-Electrode Model for Tetrapolar Bio-Impedance Measurements

This work compares two design methodologies, emulating both AgCl electrode and skin tissue Cole models for testing and verification of electrical bio-impedance circuits and systems. The models are based on fractional-order elements, are implemented with active components, and capture bio-impedance behaviors up to 10 kHz. Contrary to passive-elements realizations, both architectures using analog filters coupled with adjustable transconductors offer tunability of the fractional capacitors’ parameters. The main objective is to build a tunable active integrated circuitry block that is able to approximate the models’ behavior and can be utilized as a Subject Under Test (SUT) and electrode equivalent in bio-impedance measurement applications. A tetrapolar impedance setup, typical in bio-impedance measurements, is used to demonstrate the performance and accuracy of the presented architectures via Spectre Monte-Carlo simulation. Circuit and post-layout simulations are carried out in 90-nm CMOS process, using the Cadence IC suite.