Novel bioresorbable strontium hydroxyapatite membrane for guided bone regeneration

Incorporation of strontium-containing bioactive particles into PEOT/PBT electrospun scaffolds for bone tissue regeneration

The combination of biomaterials and bioactive particles has shown to be a successful strategy to fabricate electrospun scaffolds for bone tissue engineering. Among the range of bioactive particles, hydroxyapatite and mesoporous bioactive glasses (MBGs) have been widely used for their osteoconductive and osteoinductive properties. Yet, the comparison between the chemical and mechanical characteristics as well as the biological performances of these particle-containing scaffolds have been characterized to a limited extent. In this work, we fabricated PEOT/PBT-based composite scaffolds incorporating either nanohydroxyapatite (nHA), strontium-containing nanohydroxyapatite (nHA_Sr) or MBGs doped with strontium ions up to 15 wt./vol% and 12,5 wt./vol% for nHA and MBG, respectively. The composite scaffolds presented a homogeneous particle distribution. Morphological, chemical and mechanical analysis revealed that the introduction of particles into the electrospun meshes caused a decrease in the fiber diameter and mechanical properties, yet maintaining the hydrophilic nature of the scaffolds. The Sr²⁺ release profile differed according to the considered system, observing a 35-day slowly decreasing release from strontium-containing nHA scaffolds, whereas MBG-based scaffolds showed a strong burst release in the first week. In vitro, culture of human bone marrow-derived mesenchymal stromal cells (hMSCs) on composite scaffolds demonstrated excellent cell adhesion and proliferation. In maintenance and osteogenic media, all composite scaffolds showed high mineralization as well as expression of Col I and OCN compared to PEOT/PBT scaffolds, suggesting their ability to boost bone formation even without osteogenic factors. The presence of strontium led to an increase in collagen secretion and matrix mineralization in osteogenic medium, while gene expression analysis showed that hMSCs cultured on nHA-based scaffolds had a higher expression of OCN, ALP and RUNX2 compared to cells cultured on nHA_Sr scaffolds in osteogenic medium. Yet, cells cultured on MBGs-based scaffolds showed a higher gene expression of COL1, ALP, RUNX2 and BMP2 in osteogenic medium compared to nHA-based scaffolds, which is hypothesized to lead to high osteoinductivity in long term cultures.

Optimizing the bio-degradability and biocompatibility of a biogenic collagen membrane through cross-linking and zinc-doped hydroxyapatite

Biogenic collagen membranes have been widely used as soft tissue barriers in guided bone regeneration (GBR) and guided tissue regeneration (GTR). Nevertheless, their clinical performance remains unsatisfactory because of their low mechanical strength and fast degradation rate in vivo. Although cross-linking with chemical agents is effective and reliable for prolonging the degradation time of collagen membranes, some adverse effects including potential cytotoxicity and undesirable tissue integration have been observed during this process. As a fundamental nutritional trace element, zinc plays an active role in promoting the growth of cells and regulating the degradation of the collagen matrix. Herein, a biogenic collagen membrane was cross-linked with glutaraldehyde-alendronate to prolong its degradation time. The physiochemical and biological properties were enhanced by the incorporation of zinc-doped nanohydroxyapatite (nZnHA), with the native structure of collagen preserved. Specifically, the cross-linking combined with the incorporation of 1% and 2% nZnHA seemed to endow the membrane with the most appropriate biocompatibility and tissue integration capability among the cross-linked membranes, as well as offering a degradation period of six weeks in a rat subcutaneous model. Thus, improving the clinical performance of biogenic collagen membranes by cross-linking together with the incorporation of nZnHA is a promising strategy for the improvement of biogenic collagen membranes. STATEMENT OF SIGNIFICANCE: The significance of this research includes.

Preparation of Mg/PCL electrospun membranes and preliminary study

Magnesium (Mg) metal and its alloy degradation product magnesium ion (Mg2+) can stimulate the metabolic activity of bone cells, which is beneficial to bone growth and healing. With biodegradable polycaprolactone (PCL) and magnesium particles as raw materials, electrospinning technology is used to prepare electrospun membrane materials doped with magnesium particles. Meanwhile, the scanning electron microscope, X-ray diffraction analysis technology and microcomputer-controlled electronic universal testing machine are adopted to analyze the physical and chemical properties of the material. The biocompatibility of electrospun membranes and their potential to induce osteogenic differentiation of human dental pulp stem cells (hDPSCs) were evaluated by in vitro cell experiments. The results showed that magnesium/PCL electrospun membranes doped with magnesium particles were successfully prepared with electrospinning technology, and the material has a good porous structure. Magnesium/PCL electrospun membranes have good biocompatibility and have the potential to induce osteogenic differentiation of hDPSCs. Among them, the effects of 10% magnesium/PCL electrospun membranes were the most obvious. Clinically, these materials provide new ideas for the restoration of alveolar bone defects and provide an experimental basis for the realization of alveolar bone regeneration.

Cell type specific adhesion to surfaces functionalised by amine plasma polymers

Our previously-obtained impressive results of highly increased C2C12 mouse myoblast adhesion to amine plasma polymers (PPs) motivated current detailed studies of cell resistance to trypsinization, cell proliferation, motility, and the rate of attachment carried out for fibroblasts (LF), keratinocytes (HaCaT), rat vascular smooth muscle cells (VSMC), and endothelial cells (HUVEC, HSVEC, and CPAE) on three different amine PPs. We demonstrated the striking difference in the resistance to trypsin treatment between endothelial and non-endothelial cells. The increased resistance observed for the non-endothelial cell types was accompanied by an increased rate of cellular attachment, even though spontaneous migration was comparable to the control, i.e., to the standard cultivation surface. As demonstrated on LF fibroblasts, the resistance to trypsin was similar in serum-supplemented and serum-free media, i.e., medium without cell adhesion-mediating proteins. The increased cell adhesion was also confirmed for LF cells by an independent technique, single-cell force spectroscopy. This method, as well as the cell attachment rate, proved the difference among the plasma polymers with different amounts of amine groups, but other investigated techniques could not reveal the differences in the cell behaviour on different amine PPs. Based on all the results, the increased resistance to trypsinization of C2C12, LF, HaCaT, and VSMC cells on amine PPs can be explained most probably by a non-specific cell adhesion such as electrostatic interaction between the cells and amine groups on the material surface, rather than by the receptor-mediated adhesion through serum-derived proteins adsorbed on the PPs.

Distinctive bone regeneration of calvarial defects using biphasic calcium phosphate supplemented ultraviolet-crosslinked collagen membrane

Purpose

To overcome several drawbacks of chemically-crosslinked collagen membranes, modification processes such as ultraviolet (UV) crosslinking and the addition of biphasic calcium phosphate (BCP) to collagen membranes have been introduced. This study evaluated the efficacy and biocompatibility of BCP-supplemented UV-crosslinked collagen membrane for guided bone regeneration (GBR) in a rabbit calvarial model.

Methods

Four circular bone defects (diameter, 8 mm) were created in the calvarium of 10 rabbits. Each defect was randomly allocated to one of the following groups: 1) the sham control group (spontaneous healing); 2) the M group (defect coverage with a BCP-supplemented UV-crosslinked collagen membrane and no graft material); 3) the BG (defects filled with BCP particles without membrane coverage); and 4) the BG+M group (defects filled with BCP particles and covered with a BCP-supplemented UV-crosslinked collagen membrane in a conventional GBR procedure). At 2 and 8 weeks, rabbits were sacrificed, and experimental defects were investigated histologically and by micro-computed tomography (micro-CT).

Results

In both micro-CT and histometric analyses, the BG and BG+M groups at both 2 and 8 weeks showed significantly higher new bone formation than the control group. On micro-CT, the new bone volume of the BG+M group (48.39±5.47 mm³) was larger than that of the BG group (38.71±2.24 mm³, P=0.032) at 8 weeks. Histologically, greater new bone area was observed in the BG+M group than in the BG or M groups. BCP-supplemented UV-crosslinked collagen membrane did not cause an abnormal cellular reaction and was stable until 8 weeks.

Conclusions

Enhanced new bone formation in GBR can be achieved by simultaneously using bone graft material and a BCP-supplemented UV-crosslinked collagen membrane, which showed high biocompatibility and resistance to degradation, making it a biocompatible alternative to chemically-crosslinked collagen membranes.

Osteogenesis-Related Gene Expression and Guided Bone Regeneration of a Strontium-Doped Calcium-Phosphate-Coated Titanium Mesh

Guided bone regeneration using a perforated titanium membrane is actively used in oral and orthopedic surgeries to provide space for the subsequent filling of a new bone in the case of bone defects and to achieve proper bone augmentation and reconstruction. The surface modification of a titanium membrane using a strontium-substituted calcium phosphate coating has become a popular trend to provide better bioactivity and biocompatibility on the membrane for improving the bone regeneration because strontium can stimulate not only the differentiation of osteoblasts but also inhibit the differentiation of osteoclasts. The strontium-doped calcium phosphate coating on the titanium mesh was formed by the cyclic precalcification method, and its effects on bone regeneration were evaluated by in vitro analysis of osteogenesis-related gene expression and in vivo evaluation of osteogenesis of the titanium mesh using the rat calvarial defect model in this study. It was identified that the strontium-doped calcium phosphate-treated mesh showed a higher expression of all genes related to osteogenesis in the osteoblast cells and resulted in new bone formation with better osseointegration with the mesh in the rat calvarial defect, in comparison with the results of untreated and calcium phosphate-treated meshes.

Enhanced osteogenesis and angiogenesis by PCL/chitosan/Sr-doped calcium phosphate electrospun nanocomposite membrane for guided bone regeneration

Membranes play pivotal role in guided bone regeneration (GBR) technique for reconstruction alveolar bone. GBR membrane that is able to stimulate both osteogenic and angiogenic differentiation of cells may be more effective in clinic practice. Herein, we fabricated the Sr-doped calcium phosphate/polycaprolactone/chitosan (Sr-CaP/PCL/CS) nanohybrid fibrous membrane by incorporating 20 wt% bioactive Sr-CaP nanoparticles into PCL/CS matrix via one-step electrospinning method, in order to endow the membrane with stimulation of osteogenesis and angiogenesis. The physicochemical properties, mechanical properties, Sr²⁺ release behavior, and the membrane stimulate bone mesenchymal stem cell (BMSCs) differentiation were evaluated in comparison with PCL/CS and CaP/PCL/CS membranes. The SEM images revealed that the nanocomposite membrane mimicked the extracellular matrix structure. The release curve presented a 28-day long continuous release of Sr²⁺ and concentration which was certified in an optimal range for positive biological effects at each timepoint. The in vitro cell culture experiments certified that the Sr-CaP/PCL/CS membrane enjoyed excellent biocompatibility and remarkably promoted rat bone mesenchymal stem cell (BMSCs) adhesion and proliferation. In terms of osteogenic differentiation, BMSCs seeded on the Sr-CaP/PCL/CS membrane showed a higher ALP activity level and a better matrix mineralization. What's more, the synergism of the Sr²⁺ and CaP from the Sr-CaP/PCL/CS membrane enhanced BMSCs angiogenic differentiation, herein resulting in the largest VEGF secretion amount. Consequently, the Sr-CaP/PCL/CS nanohybrid electrospun membrane has promising applications in GBR.

Osteogenic, anti-osteoclastogenic and immunomodulatory properties of a strontium-releasing hybrid scaffold for bone repair

Strontium (Sr) is known to stimulate osteogenesis, while inhibiting osteoclastogenesis, thus encouraging research on its application as a therapeutic agent for bone repair/regeneration. It has been suggested that it may possess immunomodulatory properties, which might act synergistically in bone repair/regeneration processes. To further explore this hypothesis we have designed a Sr-hybrid system composed of an in situ forming Sr-crosslinked RGD-alginate hydrogel reinforced with Sr-doped hydroxyapatite (HAp) microspheres and studied its in vitro osteoinductive behaviour and in vivo inflammatory response. The Sr-hybrid scaffold acts as a dual Sr²⁺ delivery system, showing a cumulative Sr²⁺ release of ca. 0.3 mM after 15 days. In vitro studies using Sr²⁺concentrations within this range (0 to 3 mM Sr²⁺) confirmed its ability to induce osteogenic differentiation of mesenchymal stem/stromal cells (MSC), as well as to reduce osteoclastogenesis and osteoclasts (OC) functionality. In comparison with a similar Sr-free system, the Sr-hybrid system stimulated osteogenic differentiation of MSC, while inhibiting the formation of OC. Implantation in an in vivo model of inflammation, revealed an increase in F4/80⁺/CD206⁺ cells, highlighting its ability to modulate the inflammatory response as a pro-resolution mediator, through M2 macrophage polarization. Therefore, the Sr-hybrid system is potentially an appealing biomaterial for future clinical applications.

Bibliographic review on the state of the art of strontium and zinc based regenerative therapies. Recent developments and clinical applications

This review brings up to date the state of the art of strontium and zinc based regenerative therapies, both having a promoting effect on tissue formation and a role inhibiting resorption in musculoskeletal disorders.

Microwave-assisted synthesis and evaluation of type 1 collagen-apatite composites for dental tissue regeneration

The aim was to develop an economical and biocompatible collagen-based bioactive composite for tooth regeneration. Acid-soluble collagen was extracted and purified from fish scales. The design was innovated to molecularly tailor the surface charge sites of the nano-apatite providing chemical bonds with the collagen matrix via microwave irradiation technique. The obtained collagen was identified by sodium dodecyl sulfate polyacrylamide gel electrophoresis analysis. The composites were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis/differential scanning calorimetry, and scanning electron microscopy. MC3T3-E1 cell lines were used to assess the biological effects of these materials by 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl-tetra zolium bromide (MTT) assay. Indirect contact test was performed by extracting representative elutes in cell culture media and sulforhodamine B analysis was performed. Chorioallantoic membrane assay was conducted to define the new vessels formation behavior. The purity of collagen extracts was determined and showed two α-chains, i.e. the characteristic of type I collagen. Fourier transform infrared spectroscopy showed the characteristic peaks for amide I, I, III, and phosphate for collagen and composites. Scanning electron microscopy images showed three-dimensional mesh of collagen/apatite nano-fibers. Nontoxic behavior of composites was observed and there were graded and dose-related effects on experimental compounds. The angiogenesis and vessels formation behavior were observed in bioactive collagen composite. The obtained composites have potential to be used for tooth structure regeneration.

Biomaterials for Regenerative Medicine: Historical Perspectives and Current Trends

Biomaterials are key components in tissue engineering and regenerative medicine applications, with the intended purpose of reducing the burden of disease and enhancing the quality of life of a large number of patients. The success of many regenerative medicine strategies, such as cell-based therapies, artificial organs, and engineered living tissues, is highly dependent on the ability to design or produce suitable biomaterials that can support and guide cells during tissue healing and remodelling processes. This chapter presents an overview about basic research concerning the use of different biomaterials for tissue engineering and regenerative medicine applications. Starting from a historical perspective, the chapter introduces the basic principles of designing biomaterials for tissue regeneration approaches. The main focus is set on describing the main classes of biomaterials that have been applied in regenerative medicine, including natural and synthetic polymers, bioactive ceramics, and composites. For each class of biomaterials, some of the most important physicochemical and biological properties are presented. Finally, some challenges and concerns that remain in this field are presented and discussed.

Injectable simvastatin gel for minimally invasive periosteal distraction: In vitro and in vivo studies in rat

OBJECTIVES

To evaluate whether the subperiosteal injection of simvastatin (SIM) with a novel in situ gel-forming system, SrHA/Alg (strontium hydroxyapatite/alginate), can stimulate vertical bone augmentation in a rat calvarial model.

MATERIAL AND METHODS

The SrHA/Alg solution was synthesized and combined with different doses of SIM (0.01, 0.02, 0.1, and 0.2 mg) to form the following groups: (1) SrHA/Alg only, (2) SrHA/Alg/0.01, (3) SrHA/Alg/0.02, (4) SrHA/Alg/0.1, and (5) SrHA/Alg/0.2. The SIM release pattern was analyzed, and rat primary periosteum-derived cell (PDC) responses were investigated. Twenty male Wistar rats were enrolled in the calvarial subperiosteal injection experiment with each animal receiving a 200-μl single subperiosteal injection of SrHA/Alg with different amounts of SIM (0, 0.01, 0.02, and 0.1 mg) incorporated (n = 5). The 0.2 mg dose group was not tested in vivo due to the severe toxicity found in vitro. The new bone formation was assessed histologically and radiologically at 8 weeks.

RESULTS

The slow release of SIM was confirmed, and PDC viability decreased in the SrHA/Alg/0.2 group. Alkaline phosphatase positive areas and mineralization areas were significantly greater in the SrHA/Alg/0.01 and SrHA/Alg/0.02 groups (p < .05). The mRNA expression level of Runx2 significantly increased in the SrHA/Alg/SIM-0.02 group by day 7 (p < .05) and significantly higher levels of VEGF were found in the SrHA/Alg/0.01 and SrHA/Alg/0.02 groups at different time points (p < .05). In vivo, no prominent clinical sign of inflammation was observed, and the most significant bone gain was shown in the SrHA/Alg/0.02 group (p < .05). The osteoclast formation within the newly formed bone area was reduced in the SrHA/Alg/0.1 group (p < .05).

CONCLUSIONS

When combined with SrHA/Alg system, the 0.02 mg SIM seemed to be the optimal dose to stimulate subperiosteal bone formation without inducing inflammation. This combination may hold potential therapeutic benefits for clinical bone augmentation in a minimally invasive manner.

Guided bone regeneration: materials and biological mechanisms revisited

Guided bone regeneration (GBR) is commonly used in combination with the installment of titanium implants. The application of a membrane to exclude non‐osteogenic tissues from interfering with bone regeneration is a key principle of GBR. Membrane materials possess a number of properties which are amenable to modification. A large number of membranes have been introduced for experimental and clinical verification. This prompts the need for an update on membrane properties and the biological outcomes, as well as a critical assessment of the biological mechanisms governing bone regeneration in defects covered by membranes. The relevant literature for this narrative review was assessed after a MEDLINE/PubMed database search. Experimental data suggest that different modifications of the physicochemical and mechanical properties of membranes may promote bone regeneration. Nevertheless, the precise role of membrane porosities for the barrier function of GBR membranes still awaits elucidation. Novel experimental findings also suggest an active role of the membrane compartment per se in promoting the regenerative processes in the underlying defect during GBR, instead of being purely a passive barrier. The optimization of membrane materials by systematically addressing both the barrier and the bioactive properties is an important strategy in this field of research.

The effect of local application of low-magnitude high-frequency vibration on the bone healing of rabbit calvarial defects-a pilot study

Background

The objective of this pilot study was to evaluate the effect of local application of low-magnitude high-frequency vibration (LMHFV) on the bone healing of rabbit calvarial defects that were augmented with different grafting materials and membranes.

Methods

Four calvarial defects were created in each of two New Zealand rabbits and filled with the following materials: biphasic calcium phosphate (BCP), deproteinized bovine bone mineral covered with a non-cross-linked collagen membrane (BO/BG), biphasic calcium phosphate covered with a strontium hydroxyapatite-containing collagen membrane (BCP/SR), and non-cross-linked collagen membrane (BG). Four defects in one rabbit served as a control, while the other was additionally subjected to the local LMHFV protocol of 40 Hz, 16 min per day. The rabbits were sacrificed 1 week after surgery. Histomorphometric analysis was performed to determine the percentages of different tissue compartments.

Results

Compared to the control defects, the higher percentage of osteoid tissue was found in LMHFV BG defects (35.3 vs. 19.3%), followed by BCP/SR (17.3 vs. 2.0%) and BO/BG (9.3 vs. 1.0%). The fraction occupied by the residual grafting material varied from 40.3% in BO/BG to 22.3% in BCP/SR LMHFV defects. Two-way models revealed that material type was only significant for the osteoid (P= 0.045) and grafting material (P = 0.001) percentages, while the vibration did not provide any statistical significance for all histomorphometric outcomes (P > 0.05).

Conclusion

Local application of LMHFV did not appear to offer additional benefit in the initial healing phase of rabbit calvarial defects. Histomorphometric measurements after 1 week of healing demonstrated more pronounced signs of early bone formation in both rabbits that were related with material type and independent of LMHFV.

Gene expression profiles in guided bone regeneration using combinations of different biomaterials: a pilot animal study

OBJECTIVES

The aim of this study was to investigate the gene expression profile related to guided bone regeneration (GBR) at the early healing stage while using combinations of different biomaterials.

MATERIALS AND METHODS

Cranial defects in 4 New Zealand rabbits were filled with A) biphasic calcium phosphate/experimental pericardium-derived collagen membrane, B) Bio-Oss^® /Bio-Gide^® , C) biphasic calcium phosphate/strontium hydroxyapatite-containing collagen membrane and D) Bio-Oss^® /strontium hydroxyapatite-containing collagen membrane. Seven days after surgery, one animal was subjected to histological observation and histomorphometric analysis, and three animals to real-time quantitative reverse transcription polymerase chain reaction (PCR). An RT² Profiler PCR Array (PANZ-026Z, QIAGEN, QIAGEN Sciences, Germantown, MD, USA) was conducted to observe the gene expression profile of groups A, C and D as compared with the control group B.

RESULTS

The analysis showed 9 of the 84 genes on the array to be significantly different in the three experimental groups (six genes in group D, four in group C and one in group A). Group D demonstrated the most changes in gene expression profile at day 7. Genes that were significantly down-regulated (AHSG, EGF) or up-regulated (CDH11, MMP13, GLI1 and MCSF) are responsible for early-stage bone formation, bone remodeling and pre-osteoclast development. The gene expression profile of this group correlated with the histological findings, as this group showed the higher formation of osteoid as compared with the other groups.

CONCLUSION

Gene expression patterns at early-stage healing of GBR-treated defects appear to be related to the biomaterial used. The combination of Bio-Oss^® and strontium hydroxyapatite-containing collagen membrane showed the most pro-osteogenic gene regulation profile (group D), implying the stimulation of key transcriptional factors, which appeared to translate into the up-regulation of the osteogenic process and earlier bone formation.

Room-temperature fabrication of a three-dimensional reduced-graphene oxide/polypyrrole/hydroxyapatite composite scaffold for bone tissue engineering

The development of tissue engineering (TE) provides a promising alternative strategy for bone healing and regeneration.

Regeneration of rabbit calvarial defects using biphasic calcium phosphate and a strontium hydroxyapatite-containing collagen membrane

OBJECTIVES

Biphasic calcium phosphate (BCP) composed of 10% hydroxyapatite (HA) and 90% beta-tricalcium phosphate has been developed. Recently, a strontium hydroxyapatite-containing collagen membrane (Sr) was shown to stimulate early bone formation in rat calvarial defects at 4 weeks postoperatively, as compared with a cross-linked collagen membrane, for guided bone regeneration (GBR). The objective of this study was to evaluate these novel biomaterials for GBR in relation to a non-cross-linked collagen membrane (BG) and deproteinized bovine bone mineral (BO).

MATERIALS AND METHODS

Twenty New Zealand rabbits were used in this study. Four defects of 7 mm in diameter were created in each rabbit, and three of the defects were treated with BG/BO, Sr/BO, and Sr/BCP. Ten rabbits were sacrificed at 12 and 24 weeks, respectively. Histological and histomorphometric analyses were conducted. Volumetric densities of mineralized new bone (MNB), bone marrow (BM), residual grafting material (RG), and non-mineralized connective tissue (NCT) were determined for each group.

RESULTS

After 12 weeks, Sr/BCP yielded more MNB than BG/BO and Sr/BO with no significant difference among the three groups. After 24 weeks, however, Sr/BCP demonstrated significantly more MNB than BG/BO and Sr/BO. Both after 12 and 24 weeks, Sr/BCP showed significantly less RG than BG/BO and Sr/BO. There was a significant increase in MNB in Sr/BCP from 12 to 24 weeks.

CONCLUSIONS

In defects grafted with BCP, more MNB was formed while less RG remained, than in defects grafted with BO. The Sr membrane was as effective as BG when comparing Sr/BO with BG/BO.

Evaluations of guided bone regeneration in canine radius segmental defects using autologous periosteum combined with fascia lata under stable external fixation

Background

Although bone defect is one of the most common orthopaedic diseases, treatment remains a challenge and an issue of debate. Guided bone regeneration (GBR) is primarily accompanied by barrier membranes; however, optional membranes show some inherent flaws in clinical application. The purpose of this study was to observe the healing velocity and quality of repairing canine radius segmental defect using transferred autologous periosteum combined with fascia lata, which can provide better biological safety than other materials.

Materials and methods

Twenty adult male beagles weighing 11.45 ± 1.29 kg were used as animal models. The animals were randomly allocated into three groups, a blank control group, a fascia lata control group and a combined fascia lata and periosteum group. Standardised artificial bony defects were prepared at the radius and treated with autologous periosteum combined with fascia lata under stable external fixation. The newly formed bone-growth curve was made according to ultrasound (US) detection, and histopathologic and scanning electronic microscope (SEM) evaluations were also performed.

Results

Bone union was seen in most individuals from the autologous periosteum combined with fascia lata group, within an average of 14.2 weeks. Histopathologic and SEM examinations both showed the different osteogenesis state between groups. Necropsy confirmed US findings with regard to distance of bone defects and location.

Conclusion

These findings suggest that autologous periosteum combined with fascia lata is as effective as a GBR membrane, even in long tubular bone defects. With reliable biological safety, the autologous periosteum combined with fascia lata is expected to achieve increasing application in orthopaedic trauma patients.

Level of evidence

Not applicable, animal study.

Periodontal regeneration using strontium-loaded mesoporous bioactive glass scaffolds in osteoporotic rats

Recent studies demonstrate that the rate of periodontal breakdown significantly increased in patients compromised from both periodontal disease and osteoporosis. One pharmacological agent used for their treatment is strontium renalate due to its simultaneous ability to increase bone formation and halt bone resorption. The aim of the present study was to achieve periodontal regeneration of strontium-incorporated mesoporous bioactive glass (Sr-MBG) scaffolds in an osteoporotic animal model carried out by bilateral ovariectomy (OVX). 15 female Wistar rats were randomly assigned to three groups: control unfilled periodontal defects, 2) MBG alone and 3) Sr-MBG scaffolds. 10 weeks after OVX, bilateral fenestration defects were created at the buccal aspect of the first mandibular molar and assessed by micro-CT and histomorphometric analysis after 28 days. Periodontal fenestration defects treated with Sr-MBG scaffolds showed greater new bone formation (46.67%) when compared to MBG scaffolds (39.33%) and control unfilled samples (17.50%). The number of TRAP-positive osteoclasts was also significantly reduced in defects receiving Sr-MBG scaffolds. The results from the present study suggest that Sr-MBG scaffolds may provide greater periondontal regeneration. Clinical studies are required to fully characterize the possible beneficial effect of Sr-releasing scaffolds for patients suffering from a combination of both periodontal disease and osteoporosis.

Deregulation of bone forming cells in bone diseases and anabolic effects of strontium-containing agents and biomaterials

Age-related bone loss and osteoporosis are associated with bone remodeling changes that are featured with decreased trabecular and periosteal bone formation relative to bone resorption. Current anticatabolic therapies focusing on the inhibition of bone resorption may not be sufficient in the prevention or reversal of age-related bone deterioration and there is a big need in promoting osteoblastogenesis and bone formation. Enhanced understanding of the network formed by key signaling pathways and molecules regulating bone forming cells in health and diseases has therefore become highly significant. The successful development of agonist/antagonist of the PTH and Wnt signaling pathways are profits of the understanding of these key pathways. As the core component of an approved antiosteoporosis agent, strontium takes its effect on osteoblasts at multilevel through multiple pathways, representing a good example in revealing and exploring anabolic mechanisms. The recognition of strontium effects on bone has led to its expected application in a variety of biomaterial scaffolds used in tissue engineering strategies aiming at bone repairing and regeneration. While summarizing the recent progress in these respects, this review also proposes the new approaches such as systems biology in order to reveal new insights in the pathology of osteoporosis as well as possible discovery of new therapies.