Reformulated mineral trioxide aggregate components and the assessments for use as future dental regenerative cements

Physical, chemical and biological properties of MTA Angelus and novel AGM MTA: an in vitro analysis

INTRODUCTION

Mineral trioxide aggregate (MTA) is a calcium silicate-based cement that has changed conventional dental therapeutic approaches. This study aimed to evaluate physical, chemical and biological properties of novel AGM MTA, in comparison with MTA Angelus.

METHODS

The samples were prepared according to the manufacturer's instructions. The initial and final setting times were measured via a Gillmore needle following the ISO 6876:2012 standard. The radiopacity of the materials was evaluated against an aluminium step wedge on the basis of the ISO 6876 and 13,116 standards. The pH changes were measured at intervals of 3, 6, 24, 72, 96 and 144 h postimmersion in Hank's solution and calcium ion release was analysed after 168 h of immersion via inductively coupled plasma optical emission spectroscopy (ICP‒OES). Moreover, the cytotoxicity was assessed through the MTT assay on human dental pulp stem cells (hDPSCs) after 24 and 72 h of exposure to the set/fresh status of various dilutions of MTA extracts, following the ISO 10993-12 standard.

RESULTS

No significant difference was found between the initial setting times of the two materials (Angelus: 11.0 ± 1.0 min, AGM: 10.3 ± 1.5 min); however, MTA Angelus demonstrated a significantly shorter final setting time. Both materials met the minimum radiopacity requirements according to the ISO 6876 standard, with MTA Angelus exhibiting greater radiopacity than AGM MTA. Both materials created an alkaline environment without presenting any differences in each time point and AGM MTA released significantly greater amounts of calcium ions. In the cytotoxicity assessment, while the diluted extracts of both materials did not elicit any cytotoxic effects, the nondiluted samples, after 72 h of exposure, as well as the 30-min set AGM MTA after 24 h of exposure, were shown to be cytotoxic.

CONCLUSIONS

In conclusion, MTA Angelus presented a faster setting time and lower cytotoxicity, while AGM MTA demonstrated greater calcium ion release. However, both materials presented clinically acceptable properties and AGM MTA could be a potential alternative to MTA Angelus. However, further clinical studies are required to confirm its application.

Histologic Assessment of a Fast-Set Mineral Trioxide Aggregate (MTA) and Two Novel Antibacterial-Enhanced Fast-Set MTAs for Apexification and Periapical Healing of Teeth With Incomplete Root Formation in a Rat Model: An In Vivo Animal Study

Background Pulp necrosis in incomplete root formation halts dentine development, resulting in larger canals with fragile walls and an open apex, complicating canal instrumentation and apical stop formation. Bioactive endodontic cements such as mineral trioxide aggregate (MTA) are crucial for creating artificial apical barriers or inducing apical foramen closure, but challenges remain regarding their antimicrobial efficacy and cytotoxicity. Modifications to MTA formulations aim to address these concerns. Methods This in vivo animal study involved 80 Wistar albino rats, with incomplete root formation induced by pulp exposure. Rats were divided into four groups receiving different MTA formulations for apexification: conventional MTA, modified MTA, and MTA enhanced with metronidazole or doxycycline. Histopathological evaluations were conducted at seven and 28 days post-treatment to assess calcific barrier formation, inflammatory reactions, and antimicrobial efficacy. Results By day 7, modified MTA formulations exhibited enhanced antibacterial activity compared to conventional MTA (p = 0.000), with fewer inflammatory reactions and microorganisms. By day 28, modified formulations showed superior calcific barrier formation, particularly in the metronidazole- and doxycycline-enhanced groups compared to conventional MTA (p = 0.000). These outcomes suggest that modifications to MTA formulations improve antimicrobial efficacy and calcific barrier formation in vivo. Conclusion Novel modified MTA formulations, particularly those enhanced with metronidazole or doxycycline, exhibit superior antibacterial efficacy and calcific barrier formation compared to conventional MTA. Further long-term studies are warranted to validate these findings for potential clinical translation.

Comparative Evaluation of Push-Out Bond Strength of Conventional Mineral Trioxide Aggregate, Biodentine, a Modified Mineral Trioxide Aggregate, and Two Novel Antibacterial-Enhanced Mineral Trioxide Aggregates

Background The challenges associated with incorporating antimicrobial agents, such as the potential diminishment of the cement's physical properties, highlight the need for comprehensive evaluations. Balancing antimicrobial efficacy with the maintenance of structural integrity is a crucial aspect of material development. The acknowledgment of cytotoxic properties associated with tricalcium aluminate, a major constituent in conventional mineral trioxide aggregate (MTA), is critical in terms of long-term evaluation of treatment procedures. The primary focus of the push-out test is to evaluate the resistance of the tested material to dislodgement. Greater push-out strength implies stronger adhesion between the tested material and the tooth surface. Aim This study aims to evaluate the push-out bond strength of two antibacterial-enhanced MTAs with conventional MTA and Biodentine. Material and methods A total of five materials were tested: a) modified MTA, b) doxycycline-enhanced MTA, c) metronidazole-enhanced MTA, d) conventional MTA, and e) Biodentine. All the materials were mixed based on a predetermined powder:liquid ratio and then carried using a plastic instrument to the desired experimental design. Single-rooted permanent teeth, preferably incisors, were used in the present study. Teeth were embedded vertically in a rubber mold, and sectioning of the tooth was performed. A single operator instrumented the canal space in each slice using Gates-Glidden burs, and the mixed cements were placed in the respective groups and stored for 72 hours. A push-out test was carried out using a universal testing machine. Following the bond failure, the slices were examined under a stereomicroscope to determine the nature of the bond failure. The collected data was subjected to a one-way analysis of variance test, post hoc test, and chi-square test for statistical analysis. Results The mean push-out bond strength was found to be the highest for Biodentine (43.25 ± 0.62 megapascals (MPa)), followed by doxycycline- and metronidazole-enhanced MTAs (39.54 ± 0.65 MPa and 39.29 ± 0.16 MPa, respectively), modified MTA formulation (37.75 ± 0.73 MPa), and the lowest for conventional MTA (25.93 ± 0.7 MPa). Conventional MTA samples had an adhesive failure (89.4%), while Biodentine samples had a cohesive failure (80.3%). Mixed failures were noticed with the samples containing modified MTA formulation (71.3%), doxycycline-enhanced MTA (76.6%), and metronidazole-enhanced MTA (78.0%). Conclusion Despite not surpassing Biodentine in bond strength, antibacterial-enhanced MTAs are considered potential alternatives to conventional MTA in day-to-day clinical practice.

Comparative Evaluation of Push-out Bond Strength of Conventional Mineral Trioxide Aggregate, Biodentine, and Two Novel Antibacterial-enhanced Mineral Trioxide Aggregates

AIM

To evaluate the push-out bond strength of two newly modified mineral trioxide aggregates (MTAs) with conventional MTA and biodentine.

MATERIALS AND METHODS

Material preparation: Two commercially available bioactive bioceramics: Group I: Mineral trioxide aggregate; Group II: Biodentine; and two newly formulated modified MTAs: Group III: Doxycycline incorporated MTA formulation; Group IV: Metronidazole incorporated MTA formulation was used in the present study. All the test materials were then carried using a plastic instrument to the desired experimental design. Teeth sample preparation: A total of 120 teeth samples were collected and divided into four groups of test materials with 30 teeth samples per group. Single-rooted permanent teeth, that is, incisors were collected and stored in saline until the study was performed. Sectioning of the teeth into 2.0 ± 0.05-mm thick slices was performed perpendicular to the long axis of the tooth. The canal space was instrumented using Gates Glidden burs to achieve a diameter of 1.5 mm. All four prepared materials were mixed and placed in the lumen of the slices and placed in an incubator at 37°C for 72 hours. Push-out test and bond failure pattern evaluation: The push-out test was performed using a universal testing machine. The slices were examined under a scanning electron microscope (SEM) at 40× magnification to determine the nature of bond failure. All the collected data were recorded and statistically analyzed.

RESULTS

The mean push-out bond strength was found to be the highest for group II (37.38 ± 1.94 MPa) followed by group III (28.04 ± 2.22 MPa) and group IV (27.83 ± 1.34 MPa). The lowest mean push-out bond strength was noticed with group I (22.89 ± 2.49 MPa). This difference was found to be statistically significant (p = 0.000). Group I samples had the predominantly adhesive type of failure (86.4%), while group II samples showed the cohesive type of failure (94.2%). Both the modified MTAs (groups III and IV) primarily showed mixed types of failures.

CONCLUSION

Both the antibacterial-enhanced MTAs had better pushout bond strength compared to conventional MTA but did not outperform biodentine. Hence, it could serve as a substitute for conventional MTA due to its augmented physical properties.

CLINICAL SIGNIFICANCE

Carious pulp exposure and nonvital open apices pose a critical challenge to pediatric dental practitioners. In such circumstances, maintaining the vitality of pulp and faster healing would help in a better prognosis. Novel MTAs without any cytotoxic components, and enhanced antibacterial contents with augmented physical properties can help in treating such clinical conditions. How to cite this article: Merlin ARS, Ravindran V, Jeevanandan G, et al. Comparative Evaluation of Push-out Bond Strength of Conventional Mineral Trioxide Aggregate, Biodentine, and Two Novel Antibacterial-enhanced Mineral Trioxide Aggregates. J Contemp Dent Pract 2024;25(2):168-173.

Synthesis of a Calcium Silicate Cement Containing a Calcinated Strontium Silicate Phase

Objectives

The positive effects of strontium on dental and skeletal remineralization have been confirmed in the literature. This study aimed to assess the properties of a calcium silicate cement (CSC) containing a sintered strontium silicate phase.

Materials and Methods

The calcium silicate and strontium silicate phases were synthesized by the sol-gel technique. Strontium silicate powder in 0 (CSC), 10 (CSC/10Sr), 20 (CSC/20Sr), and 30 (CSC/30Sr) weight percentages was mixed with calcium silicate powder. Calcium chloride was used in the liquid phase. X-ray diffraction (XRD) of specimens was conducted before and after hydration. The setting time and compressive strength were assessed at 1 and 7 days after setting. The set discs of the aforementioned groups were immersed in the simulated body fluid (SBF) for 1 and 7 days. The ion release profile was evaluated by inductively coupled plasma-optical emission spectrometry (ICP-OES). Biomineralization on the specimen surface was evaluated by scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDS). Data were analyzed by the Kolmogorov-Smirnov test, one-way and mixed ANOVA, Levene's test, and LSD post hoc test (P  < 0.05).

Results

Except for an increasement in the peak intensity of hydrated specimens, XRD revealed no other difference in the crystalline phases of hydrated and nonhydrated specimens. The compressive strength was not significantly different at 1 and 7 days in any group (P  > 0.05). The setting time significantly decreased by an increase in percentage of strontium (P  < 0.05). Release of Ca and Si ions significantly decreased by an increase in percentage of strontium (P  < 0.05). SEM/EDS showed the formation of calcium phosphate deposits at 1 and 7 days.

Conclusion

Incorporation of 10-30 wt% sintered strontium silicate phase as premixed in CSC can significantly decrease the setting time without compromising the compressive strength or biomineralization process of the cement.

The Cytotoxic Assessment of Antibacterial-Enhanced Mineral Trioxide Aggregate Compared to Commercially Available Bioceramic Cements by Using Methyl-Thiazoldiphenyl-Tetrazolium (MTT) Assay on Human Dental Pulp Stem Cells: An In Vitro Study

Background and objective Preserving the vitality of the tooth is of prime significance during therapies such as direct pulp capping and pulpotomy that promote tertiary dentine formation and healing of pulp stumps. Procedures like apexogenesis and apexification also stimulate dentin and bone formation for root growth and closure. Conventional mineral trioxide aggregate (MTA) has good biocompatible and physical properties like longer setting time, presence of a cytotoxic component, i.e., tricalcium aluminate (TCA), moderate compressive strength, and moderate antimicrobial activity. Eliminating TCA and the addition of antibacterial components would improve the properties of the cement. In this study, we aimed to assess the cytotoxicity of MTA Angelus, Biodentine, and two antibacterial-enhanced MTAs by using methyl-thiazoldiphenyl-tetrazolium (MTT) assay. Materials and methods Human dental pulp was extirpated from extracted third molars, and human dental pulp stem cells (HDPSCs) were isolated and characterized by flow cytometry. HDPSCs were treated with MTA, Biodentine, or two antibacterial-enhanced MTAs depending on the study group. The control group constituted the untreated HDPSCs. The cell viability of HDPSCs was assessed using an MTT assay on days one, three, and seven. Results Varied levels of cytotoxicity were noticed at different time periods assessed using the tested materials, which was statistically significant (p=0.01). At all time periods assessed, the highest cell viability was noticed with Biodentine (88.7% on the first day, 80.4% on the third day, and 91.8% on the seventh day). Antibacterial-enhanced MTAs, either added with metronidazole or doxycycline, had more mean viable cells compared to conventional MTA on the third and seventh day (p=0.043 and 0.018 respectively). Conclusion Antibacterial-enhanced MTAs showed reduced cytotoxic properties when compared to conventional MTA. Biodentine was associated with the highest cell viability at all time periods.

Comparative Evaluation of the Physical and Antimicrobial Properties of Mineral Trioxide Aggregate, Biodentine, and a Modified Fast-Setting Mineral Trioxide Aggregate Without Tricalcium Aluminate: An In Vitro Study

Background Tricalcium aluminate, one of the major constituents of mineral trioxide aggregate (MTA), has been shown to have cytotoxic properties. Mineral trioxide aggregate has moderate to low antimicrobial activity against the most common endodontic pathogen, Enterococcus faecalis. Aim To assess the physical and antimicrobial properties of a newly modified formulation of mineral trioxide aggregate. Materials & methods The final setting time, compressive strength, and antimicrobial properties were tested for three groups of materials. The material used for Group 1 was mineral trioxide aggregate (white MTA, Angelus, Londrina, Brazil); the material for Group 2 was Biodentine (Septodont, Saint Maur des Fossés, France); and for Group 3, a modified MTA formulation was used. Results Group 1 had the longest setting time, and Group 2 had the shortest setting time. Group 3's material was set at 83.65 ± 0.28 minutes. This difference among the groups was statistically significant (p < 0.05). The highest mean compressive strength during all the time periods was seen in Group 2, followed by Group 3, and the least in Group 1. This difference in compressive strength was statistically significant (p=0.001). The largest zone of inhibition against Enterococcus faecalis, Candida albicans, and Streptococcus mutans was seen in Group 3, followed by Group 2 and Group 1. Conclusion Under the limitations of the present study, the newly modified MTA could serve as an alternative to the conventional MTA in terms of faster setting, higher strength, and better antimicrobial properties.

The Effect of Primary Root Canal Treatment on Dentinal Tubule Penetration of Calcium Silicate-based Sealers during Endodontic Retreatment

INTRODUCTION

The aim of this study was to evaluate the effect of previous root canal treatment on dentinal tubule penetration of calcium silicate-based sealers during endodontic retreatment and to compare 2 different (commonly used and modified) tubule penetration depth measurement techniques.

METHODS

The crowns of mandibular premolar teeth were removed, and root canals were prepared (ProTaper Universal; Dentsply Sirona, York, PA) and obturated using AH Plus (AH; Dentsply DeTrey, Konstanz, Germany), MTA Fillapex (MTAF; Angelus, Londrina, Brazil), and WellRoot ST (WRST; Vericom, Gyeonggi-do, South Korea); 0.1% red Rhod-2 dye (Chemodex, St Gallen, Switzerland) was added to the sealers. After storage for 3 weeks (37°C, 100% humid), the following sealer combination subgroups were created (the sealer used during the primary root canal treatment/the sealer used during the retreatment, n = 8): AH/AH, AH/MTAF, and AH/WRST; MTAF/AH, MTAF/MTAF, and MTAF/WRST; and WRST/AH, WRST/MTAF, and WRST/WRST. Green Fluo-3 dye (0.1%) was added to the sealers during retreatment. Sealer penetration depths were measured at 8 points and averaged, and the ratio of the retreatment sealer to the initial sealer was recorded as the mean tubule penetration depth ratio in the first technique, whereas the percentage of the circumferential penetration area ratios of the retreatment and initial sealers was calculated in the second technique. Statistical analyses were performed using Kolmogorov-Smirnov, Kruskal-Wallis, and Mann-Whitney U tests.

RESULTS

The mean penetration depth of AH and MTFA was found to be higher at the coronal third region in the control groups (P < .05). Both methods showed a significant difference among the groups at the coronal and median regions (P < .05). The AH/WRST, MTAH/AH, MTAF/MTAF, MTAF/WRSTS, and WRST/WRST groups showed deeper tubule penetration (first technique, P = .01). Both techniques showed that the penetration depth of the sealers was the same at the apical region (P > .05), whereas a difference was found among the techniques at the coronal and median regions. The sealers used in the previous root canal treatment limited the penetration depth of the sealers used during the retreatment process (P < .05). When MTAF was used as the initial sealer, the penetration depth of the second sealer did not change, whereas if WRST was the initial sealer, the penetration depth of the sealers at the median and apical regions is negatively affected during the retreatment process (P < .05).

CONCLUSIONS

Previous root canal treatment affects the penetration depth of calcium silicate-based sealers. The use of AH Plus and MTA Fillapex during the retreatment process showed an advantage. Both measurement techniques showed similar performances at the apical region, whereas the results varied at the coronal and midcoronal regions; therefore, a more stable sealer penetration measurement technique is still necessary.

In vitro biocompatibility and bioactivity of calcium silicate‑based bioceramics in endodontics (Review)

Calcium silicate-based bioceramics have been applied in endodontics as advantageous materials for years. In addition to excellent physical and chemical properties, the biocompatibility and bioactivity of calcium silicate-based bioceramics also serve an important role in endodontics according to previous research reports. Firstly, bioceramics affect cellular behavior of cells such as stem cells, osteoblasts, osteoclasts, fibroblasts and immune cells. On the other hand, cell reaction to bioceramics determines the effect of wound healing and tissue repair following bioceramics implantation. The aim of the present review was to provide an overview of calcium silicate-based bioceramics currently applied in endodontics, including mineral trioxide aggregate, Bioaggregate, Biodentine and iRoot, focusing on their in vitro biocompatibility and bioactivity. Understanding their underlying mechanism may help to ensure these materials are applied appropriately in endodontics.

Therapeutic tissue regenerative nanohybrids self-assembled from bioactive inorganic core / chitosan shell nanounits

Natural inorganic/organic nanohybrids are a fascinating model in biomaterials design due to their ultra-microstructure and extraordinary properties. Here, we report unique-structured nanohybrids through self-assembly of biomedical inorganic/organic nanounits, composed of bioactive inorganic nanoparticle core (hydroxyapatite, bioactive glass, or mesoporous silica) and chitosan shell - namely Chit@IOC. The inorganic core thin-shelled with chitosan could constitute as high as 90%, strikingly contrasted with the conventional composites. The Chit@IOC nanohybrids were highly resilient under cyclic load and resisted external stress almost an order of magnitude effectively than the conventional composites. The nanohybrids, with the nano-roughened surface topography, could accelerate the cellular responses through stimulated integrin-mediated focal adhesions. The nanohybrids were also able to load multiple therapeutic molecules in the core and shell compartment and then release sequentially, demonstrating controlled delivery systems. The nanohybrids compartmentally-loaded with therapeutic molecules (dexamethasone, fibroblast growth factor 2, and phenamil) were shown to stimulate the anti-inflammatory, pro-angiogenic and osteogenic events of relevant cells. When implanted in the in vivo calvarium defect model with 3D-printed scaffold forms, the therapeutic nanohybrids were proven to accelerate new bone formation. Overall, the nanohybrids self-assembled from Chit@IOC nanounits, with their unique properties (ultrahigh inorganic content, nano-topography, high resilience, multiple-therapeutics delivery, and cellular activation), can be considered as promising 3D tissue regenerative platforms.

Physical Properties and Biofunctionalities of Bioactive Root Canal Sealers In Vitro

Calcium silicate-based bioactive glass has received significant attention for use in various biomedical applications due to its excellent bioactivity and biocompatibility. However, the bioactivity of calcium silicate nanoparticle-incorporated bioactive dental sealer is not much explored. Herein, three commercially available bioactive root canal sealers (Endoseal MTA (EDS), Well-Root ST (WST), and Nishika Canal Sealer BG (NBG)) were compared with a resin-based control sealer (AH Plus (AHP)) in terms of physical, chemical, and biological properties. EDS and NBG showed 200 to 400 nm and 100 to 200 nm nanoparticle incorporation in the SEM image, respectively, and WST and NBG showed mineral deposition in Hank's balanced salt solution after 28 days. The flowability and film thickness of all products met the ISO 3107 standard. Water contact angle, linear dimensional changes, and calcium and silicate ion release were significantly different among groups. All bioactive root canal sealers released calcium ions, while NBG released ~10 times more silicon ions than the other bioactive root canal sealers. Under the cytocompatible extraction range, NBG showed prominent cytocompatibility, osteogenecity, and angiogenecity compared to other sealers in vitro. These results indicate that calcium silicate nanoparticle incorporation in dental sealers could be a potential strategy for dental periapical tissue regeneration.

Biological Effects of Tricalcium Silicate Nanoparticle-Containing Cement on Stem Cells from Human Exfoliated Deciduous Teeth

Nanomaterials can enhance interactions with stem cells for tissue regeneration. This study aimed to investigate the biological effects of tricalcium silicate nanoparticle-containing cement (Biodentine™) during or after setting on stem cells from human exfoliated deciduous teeth (SHED) to mimic clinically relevant situations in which materials are adapted. Specimens were divided into four groups depending on the start of extraction time (during (3, 6 and 12 min) or after setting (24 h)) and extracted in culture medium for 24 h for further physicochemical and biological analysis. After cell viability in serially diluted extracts was evaluated, odontogenic differentiation on SHED was evaluated by ARS staining using nontoxic conditions. A physicochemical analysis of extracts or specimens indicated different Ca ion content, pH, and surface chemistry among groups, supporting the possibility of different biological functionalities depending on the extraction starting conditions. Compared to the 'after setting' group, all 'during setting' groups showed cytotoxicity on SHED. The during setting groups induced more odontogenic differentiation at the nontoxic concentrations compared to the control. Thus, under clinically simulated extract conditions at nontoxic concentrations, Biodentine™ seemed to be a promising odontoblast differentiating biomaterial that is helpful for dental tissue regeneration. In addition, to simulate clinical situations when nanoparticle-containing cement is adjusted, biological effects during setting need to be considered.

Revascularization and limb salvage following critical limb ischemia by nanoceria-induced Ref-1/APE1-dependent angiogenesis

In critical limb ischemia (CLI), overproduction of reactive oxygen species (ROS) and impairment of neovascularization contribute to muscle damage and limb loss. Cerium oxide nanoparticles (CNP, or 'nanoceria') possess oxygen-modulating properties which have shown therapeutic utility in various disease models. Here we show that CNP exhibit pro-angiogenic activity in a mouse hindlimb ischemia model, and investigate the molecular mechanism underlying the pro-angiogenic effect. CNP were injected into a ligated region of a femoral artery, and tissue reperfusion and hindlimb salvage were monitored for 3 weeks. Tissue analysis revealed stimulation of pro-angiogenic markers, maturation of blood vessels, and remodeling of muscle tissue following CNP administration. At a dose of 0.6 mg CNP, mice showed reperfusion of blood vessels in the hindlimb and a high rate of limb salvage (71%, n = 7), while all untreated mice (n = 7) suffered foot necrosis or limb loss. In vitro, CNP promoted endothelial cell tubule formation via the Ref-1/APE1 signaling pathway, and the involvement of this pathway in the CNP response was confirmed in vivo using immunocompetent and immunodeficient mice and by siRNA knockdown of APE1. These results demonstrate that CNP provide an effective treatment of CLI with excessive ROS by scavenging ROS to improve endothelial survival and by inducing Ref-1/APE1-dependent angiogenesis to revascularize an ischemic limb.

Comparative Cytocompatibility and Mineralization Potential of Bio-C Sealer and TotalFill BC Sealer

The aim of this study was to investigate the cytocompatibility and mineralization potential of two premixed hydraulic endodontic sealers compared with an epoxy resin-based root canal sealer. The cellular responses and mineralization capacity were studied in human periodontal ligament stem cells (hPDLSCs) that were exposed to premixed hydraulic sealers, Bio-C Sealer (Angelus, Londrína, PR, Brazil), TotalFill BC Sealer (FKG Dentaire SA, La-Chaux-de-fonds, Switzerland) and an epoxy resin-based material, AH Plus (Dentsply De Trey, Konstanz, Germany). Non-exposed cultures served as the control. The endodontic sealers were assessed using scanning electron microscopy (SEM) and energy dispersive X-ray microanalysis (EDX). Statistical analyses were done using Analisis of Variance (ANOVA), with Bonferroni adjusted pairwise comparison (p = 0.05). AH Plus reduced cell viability and cell migration, whereas increased cell viability and cell migration were observed in the Bio-C Sealer and the TotalFill BC Sealer (p < 0.05). The lowest cell attachment and spreading were observed for all concentrations of AH Plus, whereas the highest were observed for TotalFill BC Sealer. At the end of 21 days, only the Bio-C Sealer and the TotalFill BC Sealer supported matrix mineralization (p < 0.05). Additionally, SEM-EDX revealed high content of calcium, oxygen, and silicon in the Bio-C Sealer and the TotalFill BC Sealer. Based on the results from this study, Bio-C Sealer and TotalFill BC Sealer demonstrated better cytocompatibility in terms of cell viability, migration, cell morphology, cell attachment, and mineralization capacity than AH Plus.

Performance of a glucose-reactive enzyme-based biofuel cell system for biomedical applications

A glucose-reactive enzyme-based biofuel cell system (EBFC) was recently introduced in the scientific community for biomedical applications, such as implantable artificial organs and biosensors for drug delivery. Upon direct contact with tissues or organs, an implanted EBFC can exert effects that damage or stimulate intact tissue due to its byproducts or generated electrical cues, which have not been investigated in detail. Here, we perform a fundamental cell culture study using a glucose dehydrogenase (GDH) as an anode enzyme and bilirubin oxidase (BOD) as a cathode enzyme. The fabricated EBFC had power densities of 15.26 to 38.33 nW/cm² depending on the enzyme concentration in media supplemented with 25 mM glucose. Despite the low power density, the GDH-based EBFC showed increases in cell viability (~150%) and cell migration (~90%) with a relatively low inflammatory response. However, glucose oxidase (GOD), which has been used as an EBFC anode enzyme, revealed extreme cytotoxicity (~10%) due to the lethal concentration of H₂O₂ byproducts (~1500 µM). Therefore, with its cytocompatibility and cell-stimulating effects, the GDH-based EBFC is considered a promising implantable tool for generating electricity for biomedical applications. Finally, the GDH-based EBFC can be used for introducing electricity during cell culture and the fabrication of organs on a chip and a power source for implantable devices such as biosensors, biopatches, and artificial organs.

Ceria-incorporated MTA for accelerating odontoblastic differentiation via ROS downregulation

OBJECTIVE

Odontoblast differentiation from dental pulp stem cells (DPSCs) is involved in a cascade of key biological events for maintaining pulp-dentin homeostasis, repair and regeneration. A pulp regeneration biomaterial (mineral trioxide aggregate (MTA)) increased intracellular reactive oxygen species (ROS) levels during differentiation, ameliorating the differentiating of DPSCs into odontoblasts. Here, ceria nanoparticles (CNP) were incorporated as an insoluble antioxidant into commercially available MTA (CMTA), and the odontoblastic differentiation of human DPSCs was investigated.

METHODS

The CMTA was fabricated from MTA and CNP conjugation up to 4wt%, and the compressive strength, surface morphology after setting and setting time were investigated. Furthermore, the alkaline phosphatase (ALP) assay, Alizarin Red staining (ARS) and quantitative real-time polymerase chain reaction (qPCR) were performed to evaluate odontoblastic differentiation in an indirect co-culture system using inserts with pores. To reveal the underlying mechanism, the ROS levels and ion release were measured. Statistical analysis was performed by one-way analysis of variance with a Tukey post hoc test (P<0.05).

RESULTS

CMTA significantly elevated the odontoblastic differentiation of hDPSCs measured by ALP activity, ARS, and odontoblastic gene expression, whereas the other physico-mechanical properties were relatively maintained. Upregulation of gene expression from CMTA was reversed with hydrogen peroxide. CMTA could reduce the increased intracellular ROS levels of hDPSCs by approximately 70% during differentiation, similar to when an antioxidant was used, without changing the ion release and pH of the media.

SIGNIFICANCE

CMTA could be useful dental materials for regenerating dentin-pulp complexes by instructing intracellular ROS during differentiation to achieve beneficial biological functions. This study suggests a new direction of dental nanomaterials in treating pulp-dentin complexes.