Evolution of Self-Assembled Au NPs by Controlling Annealing Temperature and Dwelling Time on Sapphire (0001)

Enhanced control over size, areal density, and shape of substrate-supported Au and Ag nanoparticles by solid-state dewetting and alloying

The ability to manipulate the dimensions, areal density, and form of substrate-supported Au and Ag nanoparticles (NPs) is highly desirable for utilizing their plasmonic properties in biosensing, photovoltaics, and nanophotonic applications. The transformation of thin films into the substrate-supported nanostructures by solid-state dewetting (SSD), provides an avenue to manipulate the dimensional aspects of nanostructures simply and cost-effectively on a large scale. However, spontaneous agglomeration of the film produces randomly distributed and non-uniform nanostructures that must be controlled. Here, we have systematically studied the effect of annealing temperature, between 200 °C and 750 °C, on the dewetting morphology evolution of Au, Ag, and Au-Ag bilayer ultrathin films sputter deposited on thec-plane (0001) sapphire substrates. Regardless of the film thickness, Ag films dewet faster than Au films and produce spherical NPs, compared to faceted Au NPs, with broader size distribution. Whereas, by the SSD of Au-Ag bilayer ultrathin films, highly spherical and monodisperse AuAg bimetallic NPs can be fabricated. Furthermore, we have shown the possibility of fabricating the AuAg bimetallic NPs of varying compositions by adjusting the thickness of individual layers, thus enabling us to smoothly tune the spectral location of plasmonic resonance within the visible range.

Looking Outside the Square: The Growth, Structure, and Resilient Two-Dimensional Surface Electron Gas of Square SnO2 Nanotubes

Nanotechnology has delivered an amazing range of new materials such as nanowires, tubes, ribbons, belts, cages, flowers, and sheets. However, these are usually circular, cylindrical, or hexagonal in nature, while nanostructures with square geometries are comparatively rare. Here, a highly scalable method is reported for producing vertically aligned Sb-doped SnO₂ nanotubes with perfectly-square geometries on Au nanoparticle covered m-plane sapphire using mist chemical vapor deposition. Their inclination can be varied using r- and a-plane sapphire, while unaligned square nanotubes of the same high structural quality can be grown on silicon and quartz. X-ray diffraction measurements and transmission electron microscopy show that they adopt the rutile structure growing in the [001] direction with (110) sidewalls, while synchrotron X-ray photoelectron spectroscopy reveals the presence of an unusually strong and thermally resilient 2D surface electron gas. This is created by donor-like states produced by the hydroxylation of the surface and is sustained at temperatures above 400 °C by the formation of in-plane oxygen vacancies. This persistent high surface electron density is expected to prove useful in gas sensing and catalytic applications of these remarkable structures. To illustrate their device potential, square SnO₂ nanotube Schottky diodes and field effect transistors with excellent performance characteristics are fabricated.

Plasmon-assisted nanophase engineering of titanium dioxide for improved performances in single-particle based sensing and photocatalysis

Titanium dioxide (TiO₂) due to its large bandgap, has a very limited efficiency in utilizing sunlight for photocatalysis and photoanode applications. Sensitizing with metallic nanoparticles is one of the promising routes for resolving this issue but it requires thermal annealing and proper bandgap engineering to optimize the Schottky junctions. Here we use plasmonic nanoheating to locally anneal the TiO₂ medium with a sub-nanometer (sub-nm) feature, which results in a nanophase transition from amorphous TiO₂ to anatase and rutile with a gradient configuration. Such gradient nanocoatings of rutile/anatase establish a cascade hot electron transfer via a conduction band and defect states, which improves the surface enhanced Raman scattering (SERS) performance and photocatalytic efficiency over an order of magnitude. Unlike conventional global annealing, this nanoannealing strategy with plasmonic heating enables sub-nm control at the interface between the metal and semiconductors, and this strategy not only provides new opportunities for single particle SERS, but also shows significant implications for photocatalysis and hot-electron chemistry.

Lithiation-Enabled High-Density Nitrogen Vacancies Electrocatalyze CO2 to C2 Products

Electrochemical CO₂ reduction to produce valuable C₂ products is attractive but still suffers with relatively poor selectivity and stability at high current densities, mainly due to the low efficiency in the coupling of two *CO intermediates. Herein, it is demonstrated that high-density nitrogen vacancies formed on cubic copper nitrite (Cu₃ N_x ) feature as efficient electrocatalytic centers for CO-CO coupling to form the key OCCO* intermediate toward C₂ products. Cu₃ N_x with different nitrogen densities are fabricated by an electrochemical lithium tuning strategy, and density functional theory calculations indicate that the adsorption energies of CO* and the energy barriers of forming key C₂ intermediates are strongly correlated with nitrogen vacancy density. The Cu₃ N_x catalyst with abundant nitrogen vacancies presents one of the highest Faradaic efficiencies toward C₂ products of 81.7 ± 2.3% at -1.15 V versus reversible hydrogen electrode (without ohmic correction), corresponding to the partial current density for C₂ production as -307 ± 9 mA cm^-2 . An outstanding electrochemical stability is also demonstrated at high current densities, substantially exceeding CuO_x catalysts with oxygen vacancies. The work suggests an attractive approach to create stable anion vacancies as catalytic centers toward multicarbon products in electrochemical CO₂ reduction.

Nanoscale Soft Wetting Observed in Co/Sapphire during Pulsed Laser Irradiation

Liquid drops on deformable soft substrates exhibit quite complicated wetting behavior as compared to those on rigid solid substrates. We report on a soft wetting behavior of Co nanoparticles (NPs) on a sapphire substrate during pulsed laser-induced dewetting (PLID). Co NPs produced by PLID wetted the sapphire substrate with a contact angle near 70°, which is in contrast to typical dewetting behavior of metal thin films exhibiting contact angles greater than 90°. In addition, a nanoscale γ-Al2O3 wetting ridge about 15 nm in size and a thin amorphous Al2O3 interlayer were observed around and beneath the Co NP, respectively. The observed soft wetting behavior strongly indicates that the sapphire substrate became soft and deformable during PLID. Moreover, the soft wetting was augmented under PLID in air due to the formation of a CoO shell, resulting in a smaller contact angle near 30°.

Time dependence of electrical characteristics during the charge decay from a single gold nanoparticle on silicon

In this work, we investigate the time dependence of trapped charge in isolated gold nanoparticles (Au-NPS) dispersed on n-Si substrates, based on the electrical characteristics of nano metal–semiconductor junctions. The current–voltage (I–V) characteristics have been analysed on a single Au-NP at different time intervals, using conductive mode atomic force microscopy (AFM). The Au-NPs have been characterized for their morphology and optical properties using transmission electron microscopy (TEM), ultraviolet visible (UV-vis) spectroscopy and scanning electron microscopy (SEM). The tunneling current is found to be a direct function of the trapped charge in the NP, due to the charge screening effect of the electric field at the NP/n-Si interface. The evolution of the I–V curves is observed at different time intervals until all the trapped charge dissipates. Moreover, the time needed for nanoparticles to restore their initial state is verified and the dependence of the trapped charge on the applied voltage sweep is investigated.

In this work, we investigate the time dependence of trapped charge in isolated gold nanoparticles (Au-NPS) dispersed on n-Si substrates, based on the electrical characteristics of nano metal–semiconductor junctions.

Fabrication of Various Plasmonic Pt Nanostructures via Indium Assisted Solid-State Dewetting: From Small Nanoparticles to Widely Connected Networks

In this paper, the modified solid-state dewetting (MSSD) of well-defined and various uniform Pt nanostructures is demonstrated by the auxiliary diffusion enhancement. The MSSD utilizes the introduction of metallic indium (In) layers with high diffusivity in between sapphire and platinum (Pt) layer, through which the global diffusion and dewetting of metallic atoms can be significantly enhanced. Subsequently, the In atoms can be sublimated from the NP matrix, resulting in the formation of pure Pt NPs. By the systematic control of In and Pt bi-layer thickness, various areal density, size and configuration of Pt NPs are demonstrated. The In_{2 nm}/Pt_{2 nm} bilayers establish very small and highly dense NPs throughout the temperature range due to the early maturation of growth. Intermediate size of NPs is demonstrated with the In_{45 nm}/Pt_{15 nm} bilayers with the much improved interparticle spacings by annealing between 650 and 900 °C for 450 s. Finally, the In_{30 nm}/Pt_{30 nm} bilayers demonstrate the widely connected network-like nanostructures. In addition, the finite difference time domain (FDTD) simulation is employed to exploit the local electric field distributions at resonance wavelengths. The dewetting characteristics of In/Pt bilayers is systematically controlled by the modifications of layer thickness and annealing temperature and is systematically described based on the diffusion of atoms, Rayleigh instability and surface energy minimization mechanism. The optical properties demonstrate dynamic and widely tunable localized surface plasmon resonance (LSPR) responses depending upon the various surface morphologies of Pt nanostructures.

Selective Deposition of an Ultrathin Pt Layer on a Au-Nanoisland-Modified Si Photocathode for Hydrogen Generation

Platinum, being the most efficient and stable catalyst, is used in photoelectrochemical (PEC) devices. However, a minimal amount of Pt with maximum catalytic activity is required to be used to minimize the cost of production. In this work, we use an environmentally friendly, cost-effective, and less Pt-consuming method to prepare PEC devices for the hydrogen evolution reaction (HER). The Pt monolayer catalyst is selectively deposited on a Au-nanoisland-supported boron-doped p-type Si (100) photocathode. The PEC device based on the Si photocathode with an ultralow loading of the Pt catalyst exhibits a comparable performance for the HER to that of devices with a thick Pt layer. In addition, we demonstrate that by using a thin TiO₂ layer deposited by atomic layer deposition photo-oxidation of the Si photocathode can be blocked resulting in a stable PEC performance.