Mechanical strength of stainless steel and titanium alloy mini-implants with different diameters: an experimental laboratory study

Insertion torque, flexural strength and surface alterations of stainless steel and titanium alloy orthodontic mini-implants: an in vitro study

OBJECTIVE

This study aimed to compare the insertion torque (IT), flexural strength (FS) and surface alterations between stainless steel (SS-MIs) and titanium alloy (Ti-MIs) orthodontic mini-implants.

METHODS

Twenty-four MIs (2 x 10 mm; SS-MIs, n = 12; Ti-MIs, n = 12) were inserted on artificial bone blocks of 20 lb/ft3 (20 PCF) and 40 lb/ft3 (40 PCF) density. The maximum IT was recorded using a digital torque meter. FS was evaluated at 2, 3 and 4 mm-deflection. Surface topography and chemical composition of MIs were assessed by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). General linear and mixed models were used to assess the effect of the MI type, bone density and deflection on the evaluated outcomes.

RESULTS

The IT of Ti-MIs was 1.1 Ncm greater than that obtained for the SS-MIs (p= 0.018). The IT for MIs inserted in 40 PCF test blocks was 5.4 Ncm greater than that for those inserted in 20 PCF test blocks (p < 0.001). SS-MIs inserted in higher density bone (40 PCF) had significantly higher flexural strength than the other groups, at 2 mm (98.7 ± 5.1 Ncm), 3 mm (112.0 ± 3.9 Ncm) and 4 mm (120.0 ± 3.4 Ncm) of deflection (p< 0.001). SEM evidenced fractures in the Ti-MIs. EDS revealed incorporation of 18% of C and 2.06% of O in the loaded SS-MIs, and 3.91% of C in the loaded Ti-MIs.

CONCLUSIONS

Based on the findings of this in vitro study, it seems that SS-MIs offer sufficient stability and exhibit greater mechanical strength, compared to Ti-MIs when inserted into higher density bone.

Titanium Alloy Implants with Lattice Structures for Mandibular Reconstruction

In recent years, the field of mandibular reconstruction has made great strides in terms of hardware innovations and their clinical applications. There has been considerable interest in using computer-aided design, finite element modelling, and additive manufacturing techniques to build patient-specific surgical implants. Moreover, lattice implants can mimic mandibular bone's mechanical and structural properties. This article reviews current approaches for mandibular reconstruction, their applications, and their drawbacks. Then, we discuss the potential of mandibular devices with lattice structures, their development and applications, and the challenges for their use in clinical settings.

The effect of different orthodontic mini-implant brands and geometry on primary stability (an in vitro study)

Background

In orthodontic procedures, mini-implants are routinely used as temporary anchorage devices. Early failure is primarily attributed to a variety of issues, which are mostly connected to the quality and geometry of the screw that lead to insufficient primary stability.

Objectives

To evaluate the primary stability of different sizes and brands of orthodontic mini-implants by optimizing the insertion torque value (ITV) and to clear out which one has the greatest primary stability among the most widely used mini-implants by orthodontists.

Methods

Eighty-two self-drilling mini-implants from three different brands with different sizes were used (Optimus Ortho System (Osteonic made in Korea), Smart anchor (GNI made in Korea) (1.4 × 6, 1.6 × 8 and 1.8 × 10mm) and Morelli (made in Brazil) (1.5 × 6, 1.5 × 8 and 1.5 × 10mm), made from (Ti 6Al 4V). All were drilled at a 60° angle on Sixty artificial bone blocks made from polyurethane foam with a digital torque meter device (Orthonia, Jeil made in Korea), pullout strength (tensile force) was measured with a universal testing machine to find out the best brand and size in the mean of primary stability. Data were analyzed using SPSS Version 25 and JMP Pro Version 16 software using the One-way ANOVA test, the Post hoc and Tukey HCD tests.

Results

There were significant differences between the pullout strength of different sizes for the GNI and OSTEONIC brands, while for the MORELLI brand there were no significant differences between the three different sizes considering ITV (10Ncm) whereas for ITV (20Ncm) there was a significant difference between the different sizes for the pullout of all three brands. GNI was the best brand for all the selected sizes with ITV (10Ncm) and size 1.4 × 6 for ITV (20Ncm), whereas OSTEONIC sizes 1.6 × 8 and 1.8 × 10 were the best for ITV (20Ncm) in term of primary stability.

Conclusion

GNI screws were demonstrated higher primary among the three widely used brands followed by OSTEONIC for size 1.6 × 8 and 1.8 × 10 while MORELLI was the least resistant to dislodgement for the two torque insertion values 10 N/cm and 20 N/cm.

Stress distribution for mandibular extra-alveolar anchorage at different angles and force magnitudes: a finite element study

The aim of this study was to evaluate the stress distribution in cortical and cancellous bones and within the screw when a stainless steel extra-alveolar screw (EA-S) is inserted into the retromolar region of the mandible using the finite element method (FEM). The stress values in the EA-S were highest at 60° with horizontal (shear) force and lowest at 90° with axial force. In the bones (cortical and cancellous), the stress value was greatest at 90° with horizontal force. Greater stability of the screw may be achieved by tilting it to the force when horizontal loads are applied.

Biomimetic calcium phosphate coating on medical grade stainless steel improves surface properties and serves as a drug carrier for orthodontic applications

OBJECTIVE

Recently, stainless steel (SSL) miniscrew implants have been used in orthodontic clinics as temporary anchorage devices. Although they have excellent physical properties, their biocompatibility is relatively poor. Previously, our group developed a two-phase biomimetic calcium phosphate (BioCaP) coating that can significantly improve the biocompatibility of medical devices. This study aimed to improve the biocompatibility of SSL by coating SSL surface with the BioCaP coating.

METHODS

Titanium (Ti) discs and SSL discs (diameter: 5 mm, thickness: 1 mm) were used in this study. To form an amorphous layer, the Ti discs were immersed in a biomimetic modified Tyrode solution (BMT) for 24 h. The SSL discs were immersed in the same solution for 0 h, 12 h, 24 h, 36 h and 48 h. To form a crystalline layer, the discs were then immersed in a supersaturated calcium phosphate solution (CPS) for 48 h. The surface properties of the BioCaP coatings were analysed. In addition, bovine serum albumin (BSA) was incorporated into the crystalline layer during biomimetic mineralisation as a model protein.

RESULTS

The morphology, chemical composition and drug loading capacity of the BioCaP coating on smooth SSL were confirmed. This coating improved roughness and wettability of SSL surface. In vitro, with the extension of BMT coating period, the cell seeding efficiency, cell spreading area and cell proliferation on the BioCaP coating were increased.

SIGNIFICANCE

These in vitro results show that the BioCaP coating can improve surface properties of smooth medical grade SSL and serve as a carrier system for bioactive agents.

Evidence-based selection of orthodontic miniscrews, increasing their success rate in the mandibular buccal shelf. A randomized, prospective clinical trial

Background

Skeletal anchorage has made it possible to perform complex orthodontic tooth movements that are difficult or even impossible to achieve with conventional orthodontic treatment. Mandibular buccal shelf miniscrews, used for distalization, play a particularly important role in treatment of Class III malocclusion. Unfortunately, stability of the miniscrews placed in the mandible is still considered at higher risk of failure compared to other intraoral locations. The aim of our study was to determine the influence of the miniscrew size on their long-term stability, occurrence of oral mucosa inflammation and pain lasting over 48 h after implantation.

Methods

184 Absoanchor^® miniscrews (Dentos, South Korea) in two sizes: SH2018-10 (length 10 mm, ø 1.8–2.0 mm) and SH1514-08 (length 8 mm, ø 1.4–1.5 mm) were inserted in the mandibular buccal shelf in 92 Caucasians aged 20–50 years, diagnosed with Class III malocclusion that required en-masse distalization of the mandibular dentition. Data was statistically analyzed with the level of significance set at p = .05.

Results

91.3% of the SH2018-10 and 75% of the SH1514-08 miniscrews were stable, and this difference was statistically significant (p < .05). Inflammation of the oral mucosa was noticed around both types of miniscrews and affected 50% of the SH2018-10 and 26.09% of the SH1514-08 group (p < .05). Pain lasting longer than 48 h after implantation was related to 60.87% and 20.65% of the SH2018-10 and the SH1514-08 miniscrews (p < .05), respectively. Inflammation associated with larger SH2018-10 miniscrews did not affect their stability (p > .05), contrary to the SH1514-08 ones (p < .05). When inflammation was present, the overall success rate declined to 64.29%, from 94.74% noted for TADs without inflammation. According to the log-rank test, smaller TADs failed significantly sooner than the larger ones (p = .002).

Conclusion

Larger SH2018-10 miniscrews are the anchorage of choice for the mandibular buccal shelf, despite triggering inflammation and long-lasting pain significantly more often than the smaller ones. Therefore, this issue should be discussed with every patient prior to miniscrew use. Trial registration ID: ClinicalTrials.gov Identifier: NCT05280678 Date of Registration: 15/03/2022. Retrospectively registered.

Maxillary Skeletal Expansion with Monocortical and Bicortical Miniscrew Anchorage: A 3D Finite Element Study

The aim of the present study is to use a 3D finite element analysis to investigate and compare the transverse displacement and stress distribution between stainless steel miniscrews and titanium alloy miniscrews used for monocortical and bicortical anchorage during miniscrew-assisted rapid maxillary expansions. Skull models were constructed to depict expansion after and before midpalatal suture opening at varying miniscrew insertion depths in four clinical scenarios: monocortical, monocortical deepening, bicortical, and bicortical deepening. Finite element analyses of miniscrew properties, including transverse displacement and von Mises stress distribution, were performed for each clinical scenario. Peri-implant stress was lesser in both bicortical anchorage models compared to both monocortical models. Transverse displacement in the coronal and axial planes was also greater and more parallel in both bicortical models compared to both monocortical models. Transverse displacement and peri-implant stress did not significantly differ between monocortical and monocortical deepening models or between bicortical and bicortical deepening models. From a biomechanical perspective, the bicortical deepening miniscrew anchorage is preferable to monocortical and monocortical deepening anchorage, because bicortical anchorage induces less stress on the peri-implant bone. Consequently, bicortical deepening anchorage should be considered the preferred option in challenging clinical scenarios in which strong anchorage is required for maxillary skeletal expansion.

A case report on a IV-degree thermal crush injury of right upper arm：The application of functional prosthesis implantation technology

Severe IV-degree thermal crush injury of limbs involved the subcutaneous fascia, muscle and bone, which may lead to amputation and has a great impact on the patient's quality of life. We can repair wounds with pedicle flaps or even free flaps, However, there are still huge challenges in bone defect of extremities and functional reconstruction. In recent years, with the development of functional prostheses, we have reconstructed limb functions in many patients helping them to complete their daily lives. We report a case where the right upper arm was injured by thermal crush, leading severe burns to the skin, fascia, muscle and bone. We applied a pedicled latissimus dorsi flap and a free anterolateral thigh flap to repair the wound, and realized the function of limb salvage and movement of the right upper arm by implanting 3D printed scapula, upper arm and elbow joint prostheses. This case illustrates that IV-degree burns involving bones have new technologies to repair and achieve mobility now.

Effect of Microimplant Neck Design with and without Microthread on Pullout Strength and Destruction Volume

The microthread neck concept has been applied to dental implants. This study investigated the pullout strength and destruction volume of orthodontic microimplants with and without the microthread neck design. Fifteen microimplants (diameter: 1.5 × 10 mm) of three types (Types A and B: without microimplant neck; Type C: with microimplant neck) were tested. The insertion torque (IT), Periotest value (PTV), horizontal pullout strength (HPS), and horizontal destruction volume (HDV) of each type were measured. Kruskal–Wallis H test and Dunn’s post-hoc comparison test were performed to compare the measured values of the three types of microimplants. The correlations of the measured values were used to perform the Spearman’s correlation coefficient analysis. The ITs of Types B (8.8 Ncm) and C (8.9 Ncm) were significantly higher than those of Type A (5.2 Ncm). Type B yielded the lowest PTV (4.1), and no statistical differences in PTV were observed among the three types. Type A had a significantly lower HPS (158.8 Ncm) than Types B (226.9 Ncm) and C (212.8 Ncm). The three types did not exhibit any significant differences in the HDV. The results of the Spearman’s correlation coefficient test revealed that HDV (ρ = 0.710) and IT (ρ = 0.813) were strongly correlated with HPS, whereas for PTV and HPS, it was not. HPS was strongly and significantly correlated with HDV. The orthodontic microimplant with a microimplant neck design did not perform better than that without a microthread in the mechanical strength test.

Influence of Mouthwash Rinsing on the Mechanical Properties of Polymeric Ligature Ties Used for Dental Applications

Mouthwashes are used during dental treatments to mitigate the complications caused by poor oral hygiene. However, these solutions also affect the properties of dental appliances, including those used in orthodontics. This point has been investigated in this study focusing on the changes in mechanical properties of polymeric orthodontic ligature ties. Commercial ties from four brands were characterized in terms of their maximum forces and displacement, delivery forces, molecular structures, and microscopic morphology. These properties were compared against the ties, which were rinsed with commercial mouthwashes from three manufacturers. The results showed that mouthwash rinsing significantly reduced the maximum bearable forces of ligature ties by up to 73.1%, whereas the reduction in their maximum displacement was up to 74.5% across all tested brands. Significant changes in microscopic morphology of ligature ties were observed after mouthwash rinsing, but not their molecular structure. Furthermore, mouthwash rinsing also reduced the delivery forces from ligature ties by between 20.9 and 32.9% at their first deformation cycle. It can be concluded from this study that mouthwashes have significant impact on the mechanical properties of polymeric orthodontic ligature ties and could also potentially affect the overall efficacy of orthodontic and other dental treatments.