A comparison of explanted Articular Surface Replacement and Birmingham Hip Resurfacing components

Birmingham Hip Resurfacing: a retrospective cohort study of clinical, biochemical, and radiological outcomes in a non-designer centre at minimum 15 years' follow-up

Aims

Although the use of metal-on-metal (MoM) implants in total hip arthroplasty (THA) remains a topic of controversy, prior literature has reported satisfactory ten-year clinical and radiological outcomes following Birmingham Hip Resurfacing (BHR), subsequently resulting in a recent Orthopaedic Data Evaluation Panel (ODEP) rating of 15 A*. Therefore, the purpose of this study was to evaluate the functional outcomes, radiological outcomes, and revision rates following BHR at a minimum of 15 years' follow-up in a non-designer centre.

Methods

Two investigators performed a retrospective review to identify consecutive patients who underwent BHR in our institution over a seven-year period (2003 to 2009, at minimum 15 years' follow-up) in a non-designer centre. Evaluation of clinical (Oxford Hip Scores (OHS)), biochemical (cobalt and chromium levels), and radiological (plain film radiographs) outcomes was carried out. Survivorship analysis was performed using Kaplan-Meier curves, with all-cause surgical revision defined as a definitive endpoint for analysis. Descriptive statistical analysis was carried out.

Results

Overall, 96 patients (86 males) at a mean age of 51.4 years (SD 9.9; 27 to 69) underwent 105 BHR procedures (nine bilateral) with at least 15 years' minimum follow-up. Mean OHS was 38.3 (SD 9.6; 17 to 48) at 15-year minimum follow-up. The overall survivorship was 94.3% at 15 years post BHR, with an all-cause revision rate of 5.7%. Only eight BHR prostheses (8.2%) had radiolucent lines on plain films, none of which were listed for revision at the time of latest follow-up, while 32 patients had undergone MRI at 170 months (SD 54.9; 6 to 249) post BHR, with evidence of fluid collection, aseptic lymphocyte-dominant vasculitis-associated lesion, and metallosis identified on the MRI of four patients, four patients, and one patient, respectively. For 98.4% (60/61) of patients, cobalt and chromium values were either within normal limits (68.9%, n = 42) or less than double the upper limit of normal (29.5%, n = 18).

Conclusion

This study found that BHR demonstrates an acceptable survivorship of 94% at 15 years of minimum follow-up, with satisfactory clinical and radiological outcomes to reflect this low all-cause revision rate in a non-designer centre.

Immunoglobulin A Nephropathy in a Patient With Bilateral Metal-on-Metal Hip Arthroplasty

Immunoglobulin A (IgA) nephropathy in the presence of a metal-on-metal (MoM) hip arthroplasty is a rare condition that requires close monitoring. A 61-year-old male with bilateral hip osteoarthritis underwent resurfacing hip arthroplasty with MoM articulating surfaces. Prior to his four-year postoperative visit, the patient was diagnosed with IgA nephropathy. During this visit, the patient reported clicking in the left resurfacing hip arthroplasty, and serum metal ions were significantly elevated. Consequently, the patient underwent conversion to bilateral ceramic-on-cross-linked polyethylene total hip arthroplasty, which resulted in the restoration of metal ion levels to normal. This case highlights that IgA nephropathy played a critical role in impeding the clearance of metal ions. Routine metal ion counts are warranted in patients with MoM articulating interfaces and a newly diagnosed nephropathy.

Careful patient selection together with optimal implant positioning may reduce but does not eliminate the risk of elevated serum cobalt and chrome levels following metal-on-metal hip resurfacing

BACKGROUND

Elevated serum chrome (sCr) and cobalt (sCo) concentrations are associated with local tissue adverse reactions to metal debris following metal-on-metal hip resurfacing (MoM-HR). Serum metal ions <2 µg/l are probably of little clinical relevance and a pragmatic "safe" threshold <5 µg/l has been suggested.The primary aim of this study was to evaluate if a careful selection of patients combined with optimal implant positioning could eliminate cases with "unsafe" serum metal ion levels. A secondary aim was to study the association between different risk factors and having Co and/or Cr levels >5 µg/l.

PATIENTS AND METHODS

This is a retrospective, single-institution cohort study of 410 consecutive patients operated on with a Birmingham Hip Resurfacing (BHR) implant between 2001 and 2014. 288 of these had a unilateral MoM-HR, pelvic and true lateral radiographs, and a related sCo and sCr sample, and were included in the final analysis. They were allocated to either a presumed "optimal group" consisting of only men aged <60 years old, with femoral head component >48 mm diameter, and with a cup positioned within Lewinnek's safe zones, or a "suboptimal group" consisting of the remaining patients. Fisher's exact test and multiple logistic regression analyses were performed.

RESULTS

In the optimal group 48% (47/97) had serum metal ions >2 µg/l and 8% (8/97) >5 µg/l compared to 61% (116/191) and 18% (34/191) in the suboptimal group, p = 0.059 and p = 0.034 respectively. Acetabular cups with an anteversion <5 degrees had the highest odds ratio, 6.5 (95% CI, 3.0-14.3), of having sCo and sCr concentrations exceeding 5 µg/l.

CONCLUSIONS

A well oriented BHR acetabular component in a presumably "optimal" patient reduces the risk of having elevated serum metal ions but does not eliminate it. Insufficient cup anteversion seems to be the strongest associated factor of elevated serum metals.

Are serum cobalt and chromium levels predictors for patient-reported outcome measures in the ASR hip resurfacing arthroplasty?

Aims

The aims of this study were to determine if an increasing serum cobalt (Co) and/or chromium (Cr) concentration is correlated with a decreasing Harris Hip Score (HHS) and Hip disability and Osteoarthritis Outcome Score (HOOS) in patients who received the Articular Surface Replacement (ASR) hip resurfacing arthroplasty (HRA), and to evaluate the ten-year revision rate and show if sex, inclination angle, and Co level influenced the revision rate.

Methods

A total of 62 patients with an ASR-HRA were included and monitored yearly postoperatively. At follow-up, serum Co and Cr levels were measured and the HHS and the HOOS were scored. In addition, preoperative patient and implant variables and the need for revision surgery were recorded. We used a linear mixed model to relate the serum Co and Cr levels to different patient-reported outcome measures (PROMs). For the survival analyses we used the Kaplan-Meier and Cox regression model.

Results

We found that an increase of one part per billion (ppb) in serum Co and Cr levels correlated significantly with worsening of the HHS in the following year. This significant correlation was also true for the HOOS-Pain and HOOS-quality of life sub scores. The overall ten-year survival rate in our cohort was 65% (95% confidence interval (CI) 52.5 to 77.6). Cox regression analysis showed a significant hazard ratio (HR) of 1.08 (95% CI 1.01 to 1.15; p = 0.028) for serum Co level. No significance was found with sex or inclination angle.

Conclusion

This study shows that increasing serum Co and Cr levels measured in patients with an ASR-HRA are predictive for deterioration in HHS and HOOS subscales in the following year. Increasing serum Co and Cr should forewarn both surgeon and patient that there is a heightened risk of failure. Continued and regular review of patients with an ASR-HRA implant by measurement of serum Co/Cr levels and PROMs remains essential.

Statistical Shape Modelling the In Vivo Location of Acetabular Wear in Retrieved Hip Implants

Edge-wear in acetabular cups is known to be correlated with greater volumes of material loss; the location of this wear pattern in vivo is less understood. Statistical shape modelling (SSM) may provide further insight into this. This study aimed to identify the most common locations of wear in vivo, by combining CT imaging, retrieval analysis and SMM. Shape variance was described in 20 retrieved metal-on-metal acetabular surfaces. These were revised after a mean of 90 months, from 13 female and seven male patients. They were positioned with a mean inclination and anteversion of 53° and 30°, respectively. Their orientation, in vivo, was established using their stabilising fins, visible in pre-revision CT imaging. The impact of wear volume, positioning, time, gender and size on the in vivo location of wear was investigated. These surfaces had a mean wear volume of 49.63 mm³. The mean acetabular surface displayed superior edge-wear centred 7° within the posterosuperior quadrant, while more of the volumetric wear occurred in the anterosuperior quadrant. Components with higher inclination had greater superior edge-wear scars, while a relationship was observed between greater anteversion angles and more posterosuperior edge-wear. This SSM method can further our understanding of hip implant function, informing future design and may help to refine the safe zone for implant positioning.

High rates of implant fracture of a generic polished tapered femoral stem

OBJECTIVES

Cemented polished tapered stems have demonstrated excellent long-term outcomes. Based on this concept, many generic tapered stems have been released into the market. The aim of this study was to evaluate implant-related complications of 1 specific stem design.

METHODS

Between 2010 and 2017, 315 total hip replacements were performed using a Fortress stem (Biotechni, La Ciotat, France). Patient records and radiology were retrospectively reviewed for implant-related complications. A failure analysis was performed on the failed Fortress stems in order to determine the cause of premature failure.

RESULTS

7 (2.2%) patients sustained a fracture of the neck of the implant after a mean of 5 years (range 50-81 months). All fractures were atraumatic, originating at the introducer inlet of the stem. All fractured occurred in obese patients (BMI >33 kg/m²) with a small sized prosthesis. Of these, there were 5 135° and 2 125° stems. Fracture risk was 23% (7/30) for patients with a small sized stem and a BMI >30 kg/m². All cases were revised using a cement-in-cement technique or a cementless modular revision stem. Failure analysis on the retrieved stems revealed a stress riser at the bottom of the introducer inlet.

CONCLUSIONS

An alarmingly high rate of early implant fractures was seen using this specific type of cemented stem, particularly when using smaller implant sizes in obese patients. Although based on a proven design, a specific modification led to a stress riser in the neck area, which resulted in a high incidence of implant failure. This series underlines the importance of a stepwise introduction into the market of new orthopaedic devices even when based on established concepts. Generic stems may not behave as the original stem upon which it was designed.

The in vivo location of edge-wear in hip arthroplasties : combining pre-revision 3D CT imaging with retrieval analysis

Aims

Acetabular edge-loading was a cause of increased wear rates in metal-on-metal hip arthroplasties, ultimately contributing to their failure. Although such wear patterns have been regularly reported in retrieval analyses, this study aimed to determine their in vivo location and investigate their relationship with acetabular component positioning.

Methods

3D CT imaging was combined with a recently validated method of mapping bearing surface wear in retrieved hip implants. The asymmetrical stabilizing fins of Birmingham hip replacements (BHRs) allowed the co-registration of their acetabular wear maps and their computational models, segmented from CT scans. The in vivo location of edge-wear was measured within a standardized coordinate system, defined using the anterior pelvic plane.

Results

Edge-wear was found predominantly along the superior acetabular edge in all cases, while its median location was 8° (interquartile range (IQR) -59° to 25°) within the anterosuperior quadrant. The deepest point of these scars had a median location of 16° (IQR -58° to 26°), which was statistically comparable to their centres (p = 0.496). Edge-wear was in closer proximity to the superior apex of the cups with greater angles of acetabular inclination, while a greater degree of anteversion influenced a more anteriorly centred scar.

Conclusion

The anterosuperior location of edge-wear was comparable to the degradation patterns observed in acetabular cartilage, supporting previous findings that hip joint forces are directed anteriorly during a greater portion of walking gait. The further application of this novel method could improve the current definition of optimal and safe acetabular component positioning.

Cite this article: Bone Joint Res 2021;10(10):639–649.

Capsular ligaments provide a passive stabilizing force to protect the hip against edge loading

AIMS

In the native hip, the hip capsular ligaments tighten at the limits of range of hip motion and may provide a passive stabilizing force to protect the hip against edge loading. In this study we quantified the stabilizing force vectors generated by capsular ligaments at extreme range of motion (ROM), and examined their ability to prevent edge loading.

METHODS

Torque-rotation curves were obtained from nine cadaveric hips to define the rotational restraint contributions of the capsular ligaments in 36 positions. A ligament model was developed to determine the line-of-action and effective moment arms of the medial/lateral iliofemoral, ischiofemoral, and pubofemoral ligaments in all positions. The functioning ligament forces and stiffness were determined at 5 Nm rotational restraint. In each position, the contribution of engaged capsular ligaments to the joint reaction force was used to evaluate the net force vector generated by the capsule.

RESULTS

The medial and lateral arms of the iliofemoral ligament generated the highest inbound force vector in positions combining extension and adduction providing anterior stability. The ischiofemoral ligament generated the highest inbound force in flexion with adduction and internal rotation (FADIR), reducing the risk of posterior dislocation. In this position the hip joint reaction force moved 0.8° inbound per Nm of internal capsular restraint, preventing edge loading.

CONCLUSION

The capsular ligaments contribute to keep the joint force vector inbound from the edge of the acetabulum at extreme ROM. Preservation and appropriate tensioning of these structures following any type of hip surgery may be crucial to minimizing complications related to joint instability. Cite this article: Bone Joint Res 2021;10(9):594-601.

Living with a recalled implant: a qualitative study of patients' experiences with ASR hip resurfacing arthroplasty

Background

Total hip arthroplasty is the traditional treatment for osteoarthritis in the hip joint. Hip resurfacing arthroplasty, with metal on metal bearing, is a modern concept initially developed mainly for young active people. The metal-on-metal hip arthroplasty implant, Articular Surface Replacement (ASR), was implanted in approximately 93,000 patients before it was recalled in 2010 due to a high complication rate. This study aimed to evaluate patients’ own experiences living with an implant that they knew had a high complication rate and had been recalled from the market.

Methods

A total of 14 patients, still living with the implant, of a cohort of 34 patients were available for follow-up. Qualitative semi-structured interviews were conducted with 14 patients where a majority actively sought for metal-on-metal hip resurfacing arthroplasty (HRA), and subsequently underwent HRA with an ASR prosthesis between 11/21/2006 and 09/28/2009. The responses were analyzed using content analysis described by Graneheim and Lundman to compress text and identify categories and subcategories.

Results

The results showed that most patients had already decided that they wanted a metal-on-metal HRA implant before meeting the surgeon. They expressed that the implant made it possible to live an active life. A majority did not think about the fact that they had a hip implant, because they lacked subjective pain. Most of the patients were positive about the annual exams at the hospital and wanted them to continue. None of them felt that their trust towards the healthcare system had changed after the implant recall. They expressed a belief that they would need new surgery sooner than they first thought.

Conclusions

Despite all the attention when the ASR prosthesis was recalled, patients with ASR-HRA did not report themselves negatively affected by the recall in this group of patients where a majority had actively sought for an HRA procedure. The healthcare system has an obligation to continue the annual exams, even if the implant provider does not continue reimbursement.

Supplementary Information

The online version contains supplementary material available at 10.1186/s13037-020-00278-y.

Does diametrical clearance influence the wear of Pinnacle hip implants?

Aims

The optimum clearance between the bearing surfaces of hip arthroplasties is unknown. Theoretically, to minimize wear, it is understood that clearances must be low enough to maintain optimal contact pressure and fluid film lubrication, while being large enough to allow lubricant recovery and reduce contact patch size. This study aimed to identify the relationship between diametrical clearance and volumetric wear, through the analysis of retrieved components.

Methods

A total of 81 metal-on-metal Pinnacle hips paired with 12/14 stems were included in this study. Geometrical analysis was performed on each component, using coordinate and roundness measuring machines. The relationship between their as-manufactured diametrical clearance and volumetric wear was investigated. The Mann-Whitney U test and unpaired t-test were used, in addition to calculating the non-parametric Spearman's correlation coefficient, to statistically evaluate the acquired data.

Results

The hips in this study were found to have had a median unworn diametrical clearance of 90.31 μm (interquartile range (IQR) 77.59 to 97.40); 32% (n = 26) were found to have been below the manufacturing tolerance. There was no correlation found between clearance and bearing (r_s = -0.0004, p = 0.997) or taper (r_s = 0.0048, p = 0.966) wear rates. The wear performance of hips manufactured within and below these specifications was not significantly different (bearing: p = 0.395; taper: p = 0.653). Pinnacles manufactured from 2007 onwards had a greater prevalence of bearing clearance below tolerance (p = 0.004).

Conclusion

The diametrical clearance of Pinnacle hips did not influence their wear performance, even when below the manufacturing tolerance. The optimum clearance for minimizing hip implant wear remains unclear.Cite this article: Bone Joint Res 2020;9(8):515-523.

Preliminary report of clinical experience with metal-on-highly-crosslinked-polyethylene hip resurfacing

Objectives

Modern metal-on-metal (MoM) hip resurfacing arthroplasty (HRA), while achieving good results with well-orientated, well-designed components in ideal patients, is contraindicated in women, men with head size under 50 mm, or metal hypersensitivity. These patients currently have no access to the benefits of HRA. Highly crosslinked polyethylene (XLPE) has demonstrated clinical success in total hip arthroplasty (THA) and, when used in HRA, potentially reduces metal ion-related sequelae. We report the early performance of HRA using a direct-to-bone cementless mono-bloc XLPE component coupled with a cobalt-chrome femoral head, in the patient group for whom HRA is currently contraindicated.

Methods

This is a cross-sectional, observational assessment of 88 consecutive metal-on-XLPE HRAs performed in 84 patients between 2015 and 2018 in three centres (three surgeons, including the designer surgeon). Mean follow-up is 1.6 years (0.7 to 3.9). Mean age at operation was 56 years (sd 11; 21 to 82), and 73% of implantations were in female patients. All patients were individually counselled, and a detailed informed consent was obtained prior to operation. Primary resurfacing was carried out in 85 hips, and three cases involved revision of previous MoM HRA. Clinical, radiological, and Oxford Hip Score (OHS) assessments were studied, along with implant survival.

Results

There was no loss to follow-up and no actual or impending revision or reoperation. Median OHS increased from 24 (interquartile range (IQR) 20 to 28) preoperatively to 48 (IQR 46 to 48) at the latest follow-up (48 being the best possible score). Radiographs showed one patient had a head-neck junction lucency. No other radiolucency, osteolysis, component migration, or femoral neck thinning was noted.

Conclusion

The results in this small consecutive cohort suggest that metal-on-monobloc-XLPE HRA is successful in the short term and merits further investigation as a conservative alternative to the current accepted standard of stemmed THA. However, we would stress that survival data with longer-term follow-up are needed prior to widespread adoption.

Cite this article: R. B. C. Treacy, J. P. Holland, J. Daniel, H. Ziaee, D. J. W. McMinn. Preliminary report of clinical experience with metal-on-highly-crosslinked-polyethylene hip resurfacing. Bone Joint Res 2019;8:443–450. DOI: 10.1302/2046-3758.810.BJR-2019-0060.R1

Subject-Specific Surgical Planning for Hip Replacement: A Novel 2D Graphical Representation of 3D Hip Motion and Prosthetic Impingement Information

Prosthetic impingement (PI) following total hip arthroplasty (THA), which arises due to the undesirable relative motion of the implants, results in adverse outcomes. Predicting PI through 3D graphical representation is difficult to comprehend when all activities are combined for different implant positions. Therefore, the aim of the paper was to translate this 3D information into a 2D graphical representation for improved understanding of the patient’s hip motion. The method used planned implanted geometry, positioned onto native bone anatomy, and activity definitions as inputs to construct the 2D polar plot from 3D hip motion in four steps. Three case studies were performed to highlight its potential use in (a) combining different activities in a single plot, (b) visualising the effect of different cup positions and (c) pelvic tilt on PI. A clinical study with 20 ‘Non-Dislocators’ and 20 ‘Dislocators’ patients after 2 years of THA was performed to validate the method. The results supported the study hypothesis, in that the incidence of PI was always higher in the ‘Dislocators’ compared to the ‘Non-Dislocators’ group. The proposed 2D graphical representation could assist in subject-specific THA planning by visualising the effect of different activities, implant positions, pelvic tilt and related aspects on PI.

Changes in periacetabular bone mineral density five years after resurfacing hip arthroplasty versus conventional total hip arthroplasty

INTRODUCTION:

We studied whether acetabular bone mineral density (BMD) is better preserved after resurfacing hip arthroplasty (RHA) versus small diameter metal-on-metal total hip arthroplasty (THA).

METHODS:

This randomised controlled trial included 82 patients. BMD was measured in 5 periprosthetic regions of interest (ROI) with dual-energy absorptiometry (DEXA) preoperatively, at 3 and 6 months, 1, 2, 3 and 5 years postoperative. 34 RHA and 26 THA had a complete 5 years follow-up. 1 RHA and 1 THA were revised due to pseudotumour formation, 2 THA were revised because of recurrent dislocations and 1 RHA for avascular necrosis.

RESULTS:

Overall an initial decrease in BMD was observed for both implants, stabilising after 2 years. 5 years after RHA a BMD change of +1% in upper cranial, -4% ( p < 0.01) in cranial, -8% ( p < 0.01) in craniomedial, -7% ( p < 0.01) in medial and +4% in caudal ROI compared to baseline values was seen. 5 years after THA a BMD change of -3% ( p = 0.01), -13% ( p < 0.01), -21% ( p < 0.01), -11% ( p < 0.01) and -2% for each respective ROI. The observed BMD decrease in different regions was structurally favouring the RHA-cup, with significantly higher levels in the cranial and craniomedial ROI.

CONCLUSION:

Acetabular BMD is better preserved behind a rigid press-fit convex cup in RHA compared to a titanium threaded cup in conventional THA in the cranial and craniomedial ROI. Despite of a theoretical higher stress-shielding behind the stiff acetabular component in RHA, compared to the more elastic threaded titanium THA-cup, bone depletion behind the RHA component does not seem to be of major concern.

REGISTRATION:

EudraCT (2006-005610-12).

Long - term survivorship and clinical results of the navigated withdrawn ASR ™

Introduction

Primary goals of the study were to present the mid - to long - term survivorship and clinical, radiological and metal serological results of the first stem - navigated ASR™ resurfacing at our clinic. Secondary goals were to determine the influence of stem - navigation on the outcome and risk factors for revision in our cohort.

Methods

From Mai 2006 to Mai 2009 46 ASR™ resurfacing hip systems have been implanted in 43 patients with a median age of 55 years. At final follow - up (33 patients with a mean follow -up of 89,6 months) guidelines were followed and HHS and HOOS were completed. Inclination, NSA and SSA were measured on radiographs and signs of loosening were graded. Risk factors for revision were compared in the non - revision and revision group.

Results

Mean cumulative survival of the prosthesis after 99,9 Months was 81,8%. At final follow - up 8 revisions were performed. Median HHS was 97, HOOS was 87,2. Four prostheses showed signs of loosening and nine heterotopic ossifications. All shaft components, except one, were placed in minimal valgus position to avoid risk for fracture. Age and diameter of the femoral component were significantly different between the non - revision and revision group.

Discussion

Survivorship is comparable to numbers found in other studies. Patients with complete final follow - up in general had good objective and subjective scores and few signs of loosening in the radiological follow - up. Navigation might have a positive effect on reduction of risk for fracture. Age and diameter of the femoral component seem to influence the outcome.

Five Hundred Fifty-five Retrieved Metal-on-metal Hip Replacements of a Single Design Show a Wide Range of Wear, Surface Features, and Histopathologic Reactions

BACKGROUND

In 2010, a widely used metal-on-metal hip implant design was voluntarily recalled by the manufacturer because of higher than anticipated failure rates at 5 years. Although there was a large published range of revision rates, numerous studies had reported a higher risk of revision for excessive wear and associated adverse tissue reactions when compared with other metal-on-metal total hips. The reasons for this were suggested by some to be related to cup design features.

QUESTIONS/PURPOSES

From retrievals of ASR metal-on-metal implants and tissue samples obtained at revision surgery, we asked the following questions: (1) What were the common and uncommon surface features? (2) What were the common and uncommon linear and volumetric wear characteristics? (3) Were there common taper corrosion characteristics? (4) What aseptic lymphocytic vasculitis-associated lesion (ALVAL) features were present in the tissues?

METHODS

Five hundred fifty-five ASRs, including 23 resurfacings, were studied at one academic research center. Features of wear (eg, light and moderate scratching), damage (eg, deposits, gouges), and bone attachment on the porous coating were semiquantitatively ranked from 0 (none) to 3 (> 75%) based on the amount of a feature in each region of interest by the same experienced observer throughout the study. Visible features of head taper corrosion were ranked (Goldberg score) from 1 (none) to 4 (severe) by the same observer using a previously published scoring method. An experienced tribologist measured component wear depth using a coordinate measuring machine and quantified wear volume using previously validated methods. All available tissues were sampled and examined for features of ALVAL and scored from 0 to 10 by a single observer using a method they previously developed and published. A score from 0 to 4 is considered low, 5 to 8 is considered moderate, and 9 or 10 is considered high with regard to the risk of metal hypersensitivity features in the tissues.

RESULTS

The most common bearing surface features were light and moderate scratches and removal or postremoval damage. Discoloration and deposits were commonly observed on femoral heads (55% [305 of 553]) and less commonly on cups (30% [165 of 546]). There was no evidence of impingement or dislocation damage. There was typically a small amount of bone attachment in at least one of eight designated regions of interest (84% [460 of 546]); extensive or no bone attachment was uncommon. Edge wear was highly prevalent. The maximum wear of 469 cups (88%) occurred near the edge, whereas the maximum wear of 508 femoral heads (94%) occurred between the pole and 45° from the pole. The median combined head-cup wear volume was 14 mm (range, 1-636 mm). One hundred sixty-nine pairs (32%) had a combined wear volume of < 10 mm, 42 pairs (8%) had volumetric wear of > 100 mm, and 319 pairs (60%) had wear volume between 10 and 100 mm³. Seventy-four percent of tapers (390 of 530) received a Goldberg score of 4, 22% (116 of 530) a score of 3, < 5% (24 of 530) a score of 2, and none received a score of 1. The most frequent ALVAL score was 5 out of 10 (35 of 144 hips [24%]) and ranged from 2 (one hip) to 10 (nine hips); 92 of 144 (64%) had a moderate score, 17 of 144 (12%) had a high score, and 35 (24%) had a low score.

CONCLUSIONS

Although edge wear was prevalent, in most cases, this was not associated with high wear. The increased diameter and decreased coverage angle of the ASR design may have resulted in the observed high incidence of edge wear while perhaps decreasing the risk for impingement and dislocation.

CLINICAL RELEVANCE

The role of bearing wear in the revisions of metal-on-metal implants is controversial, because it is known that there is a large range of in vivo wear rates even within the same implant type and that patient variability affects local tissue responses to wear debris. The observations from our study of 555 retrieved ASR implant sets indicate that there was a wide range of wear including a subset with very high wear. The results suggested that the failure of the ASR and ASR XL was multifactorial, and the failure of different subgroups such as those with low wear may be the result of mechanisms other than reaction to wear debris.

The effect of seated pelvic tilt on posterior edge-loading in total hip arthroplasty: A finite element investigation

Edge-loading of a ceramic-on-ceramic total hip replacement can lead to reproducible squeaking and revision. A patient’s functional acetabular cup orientation, driven by their pelvic tilt, has been shown to be a significant factor in squeaking during hip flexion. The aim of this study was to investigate the effect of seated pelvic tilt on the contact mechanics at the ceramic bearing surface. A finite element model of a ceramic-on-ceramic total hip replacement was created. The cup was orientated at 40° inclination and 15° anteversion relative to the anterior pelvic plane. The stem was flexed 90° to replicate sitting in a chair. The model was loaded using data from in vivo measurements taken during a sit-to-stand activity. The pelvis was modelled in seven different sagittal positions, ranging from −30° to 30° of pelvic tilt, where a positive value denotes anterior pelvic tilt. Three different head sizes were investigated: 32, 36 and 40 mm. The maximum contact pressure and contact patch to rim distance were determined for each of the 21 simulations. Edge-loading (contact patch to rim distance < 0 mm) occurred with all head sizes when seated pelvic tilt was ≥10° and induced a large increase in contact pressure on the liner, with a maximum pressure exceeding 500 MPa. Edge-loading initiated at seated pelvic tilts of 7°, 9° and 5° for the 32, 36 and 40 mm heads, respectively. Patients with anterior pelvic tilts in the seated position are susceptible to posterior edge-loading. As the position of the pelvis when seated is patient specific, cup orientation should be adjusted on an individual basis to minimise edge-loading.

Birmingham Hip Resurfacing vs Total Hip Arthroplasty: A Matched-Pair Comparison of Clinical Outcomes

BACKGROUND

Birmingham hip resurfacing (BHR) has proven to be a good alternative for younger patients with osteoarthritis. Some have asserted that BHR may yield outcomes which are superior to total hip arthroplasty (THA), and that some studies which failed to show a difference were plagued by ceiling effects and lack of sensitivity of outcome measures. The purpose of this study is to compare outcomes of BHR and THA using the "Forgotten Joint" Score-12 (FJS), a more sensitive score with lesser vulnerability to the ceiling effect.

METHODS

Patients who underwent BHR were matched to patients who underwent posterior THA by computing a propensity score using 5 covariates: age, body mass index, gender, worker's compensation claims, and previous hip surgery. Surgical outcomes were assessed using 6 patient-reported outcome measures, including the FJS, the visual analog scale for pain, and patient satisfaction.

RESULTS

There were 42 patients in the BHR group and 18 patients in the THA group. The FJS was 78.0 for the BHR group and 76.0 for the THA group. The Veterans RAND 12-Item Health Survey Mental Component Summary and Short Form 12 Mental Component Summary were significantly higher in the BHR group. No differences were seen between all other patient-reported outcomes.

CONCLUSION

BHR offers excellent results in young patients that are comparable to THA. As no clinical difference could be shown between BHR and THA, even with the use of the FJS, the choice between BHR and THA should not be based solely on any expectation that either yields superior clinical outcomes compared to the other at short-term follow-up.

Microstructure and Surface Damage in Retrieved Metal-on-Metal Hip Arthroplasties

BACKGROUND

Besides promising results of metal-on-metal (MOM) hip arthroplasty (HA), frequent failures have been reported even in the short term. Many host, surgical, design, metallurgical, and processing factors have been evoked in the base of these events. We have tried to characterize and to evaluate metallurgical and processing features present in this type of implants.

METHODS

The acetabular and femoral components of 20 MOM HAs collected from a multicenter retrieval program were examined. All the specimens were inspected with naked eye, with confocal microscopy and vertical scanning interferometry, scanning electron microscopy, back-scattered electron imaging, and energy-dispersive X-ray spectroscopy, in 25 zones of each articular component.

RESULTS

Gas pores, shrinkage voids and holes of detached carbides, carbides on surface, embedded particles, scratches and marks of wear, surface discoloration, surface deposits, and tribochemical reaction layers were widely dispersed through a substantial percentage of the total bearing surface in all the implanted components. Surface cup and head voids, and cup scratches showed significant correlation with the clearance of pair. A higher surface damage of the cup and head was observed mainly in the low clearance prostheses. There was no other significant correlation or difference in the incidence and importance of any of these defects between resurfacing hip arthroplasties and total hip arthroplasties, or according to the pair diameter.

CONCLUSION

Some metallurgical features and surface damage were significantly present in the retrieved implants of MoM HAs. It would be desirable to improve the structure and metallurgical characteristics of these implants to avoid those effects and optimize their performance.

Impact of Raised Serum Cobalt Levels From Recalled Articular Surface Replacement Hip Prostheses on the Visual Pathway

BACKGROUND

The articular surface replacement (ASR) was recalled in 2010 because of higher than expected revision rates. Patients reported symptoms of neurologic dysfunction including poor vision. This cohort study, using objective measurements, aimed to establish whether a higher incidence of visual function defects exists in ASR patients.

METHODS

Thirty-three ASR patients and 33 non-ASR controls (control 1) were recruited. Data were compared with normative population data from the visual electrophysiology database (control 2). Patients underwent investigations for serum cobalt levels, psychophysical visual tests, and extensive electrophysiological visual testing.

RESULTS

After excluding 2 subjects with pre-existing eye disease, data from 33 ASR patients were compared with the 2 control cohorts. The median serum cobalt level in the ASR group (median, 52 nmol/L [interquartile range, 14-151 nmol/L]) was significantly higher than that in the control 1 cohort (median, 7 nmol/L [interquartile range, 5-14 nmol/L]; P < .0001). The photoreceptor function of patients with an ASR of the hip showed significantly larger electroretinography mixed rod-cone b-wave amplitudes than both control 1 and control 2 cohorts (P = .0294 and .0410, respectively). Abnormalities in macular function as reflected by multifocal and scotopic electroretinography were more prevalent in control 1 (P = .0445 and .0275, respectively). Optic nerve pathway measurements using visual-evoked potential latency was significantly longer in the ASR group compared with those in the control 2 cohort (P = .0201). There were no statistical differences in visual acuity.

CONCLUSION

A statistically significant disturbance in visual electrophysiology was found in the ASR group when compared with the control groups. These differences did not translate to identifiable clinical visual deficits. Orthopedic surgeons need to be aware of the possibility of visual dysfunction in patients with ASR and other metal-on-metal hip arthroplasties; however, routine visual testing is not recommended.

Risk factors for wear-related failures after hip resurfacing in patients with a low contact patch to rim distance

Aims

A contact patch to rim (CPR) distance of < 10 mm has been associated with edge-loading and excessive wear. However, not all arthroplasties with a low CPR distance show problems with wear. Therefore, CPR distance may not be the only variable affecting the post-operative metal ion concentrations.

Patients and Methods

We used multiple logistic regression to determine what variables differed between the patients who had high and low cobalt (CoS) and chromium (CrS) serum ion concentrations within a cohort of patients with low (< 10 mm) CPR distances. A total of 56 patients treated with unilateral hip resurfacing arthroplasty (HRA) had CoS and CrS ion studies performed more than one year after surgery. The mean age of the patients at the time of surgery was 51.7 years (29 to 70), with 38 women (68%) and 18 men (32%).

Results

It was seen that 47 patients had low ion levels (< 7µg/L) and nine had high ion levels (≥ 7µg/L). We found increased risks of high wear with decreasing CPR distance.

Conclusion

The use of CPR distance measurements to predict hips at risk for elevated wear is needed for all patients with HRA. We recommend that patients with low CPR distances have at least one serum ion study performed while patients with CPR distance > 10 mm do not need routine ion studies. We believe that patients with low CPR distance and low ions do not need repeat ion studies unless the patient becomes symptomatic or has substantial radiographic changes. Cite this article: Bone Joint J 2017;99-B:865–71.

Outcomes of the Recalled Articular Surface Replacement Metal-on-Metal Hip Implant System: A Systematic Review

BACKGROUND

The aim of this review was to synthesize the main findings of clinical studies that have evaluated outcomes of the articular surface replacement (ASR) Hip System.

METHODS

We performed a systematic literature search to identify all articles published between January 2008 and June 2015 that included ASR hip resurfacing arthroplasty (ASR HRA) or ASR total hip arthroplasty (ASR XL THA) outcomes according to the PRISMA statement.

RESULTS

A total of 56 studies were assessed. The prevalence of adverse local tissue reactions (ALTRs) and revision rates were found to be high. ALTR prevalence varied from 12.5% to 69% (mean, 33.5%). Mean revision rate for any reason at 4-year to 7-year follow-up was 13.8% (range, 5.6%-31%) for ASR HRA and 14.5% (range, 0%-37%) for ASR XL THA. Femoral head size <53 mm was found to correlate with higher blood metal ion levels. Femoral head size >44 mm was not associated with higher ALTR prevalence or revision rates in ASR XL THA. High blood metal ion levels (>7 μg/L Co, >7 μg/L Cr) were associated with higher failure rates and bearing-related complications. The role of cup positioning was found to be controversial.

CONCLUSION

ALTR prevalence and failure rates were high. High blood metal ion levels were a risk factor for ALTR and failure. Surprisingly, the role of cup positioning and large femoral head size in ASR XL THA were controversial. These findings should be considered in the clinical follow-up and risk stratification of patients with the ASR Hip System.

Lessons learnt from metal-on-metal hip arthroplasties will lead to safer innovation for all medical devices

Metal-on-metal bearings were re-popularised in the late 1990s with the introduction of modern hip resurfacing. Large diameter (LD) metal-on-metal (MoM) hips became more prevalent and have been the least successful group of hip implants ever used. They were rapidly adopted from 2004 until the British Hip Society stopped their use in 2012. Well functioning MoM hip results (including the BHR and Metasul) are hidden in the mire of poor results from the group of all MoM bearings.We have reviewed what happened and we make 3 observations. Firstly, collaboration between surgeons and then between surgeons and other disciplines, first identified and then solved the clinical management problems. Secondly, the problems with MoM hips occurred because hip simulation was inadequate at predicting performance in patients. They gave no indications of the biological effects of wear in the human environment. Lastly, retrieval of failed implants was essential to understanding why failure occurred.These lessons must never be forgotten and must form the basis by which new or altered implants are introduced and how they should be monitored. This will enable safer innovation for patients, surgeons and manufacturers. The problems with MoM hips will not have been in vain.

Hip resurfacing: history, current status, and future

Hip resurfacing arthroplasty (HRA) presents several advantages over conventional total hip arthroplasty (THA), including conservation and preservation of bone, reduced risk of dislocation, easy replication of hip biomechanics and easy revision if needed. It is a particularly appealing procedure for young patients. HRA has been performed for over 40 years following the same technological advances as THA. The bearing material used by most designs is metal-on-metal (MoM), which has the best compromise between strength and wear properties. However, MoM HRA has a specific set of possible complications. Aseptic femoral failures were initially the most prevalent cause for revision but progress in patient selection and surgical technique seem to have resolved this problem. Wear-related failures (high metal ion levels and adverse local tissue reactions) are now the main concern, and are essentially associated with poor acetabular component design and orientation, to which MoM is more sensitive than other bearing materials. The concept of functional coverage is key to understanding how MoM bearings are affected by edge wear. Only a 3-D assessment of cup position (e.g., the contact patch to rim distance) provides the necessary information to determine the role of cup positioning in relationship with abnormal bearing wear.The concept of hip resurfacing is more valid today than ever as the age of the patients in need of hip arthroplasty keeps getting lower. The recent publication of several excellent long-term survivorship results suggests that selection of a well-designed resurfacing system and accuracy in the placement of the cup can achieve long-term durability.

Gait alterations can reduce the risk of edge loading

Following metal-on-metal hip arthroplasty, edge loading (i.e., loading near the edge of a prosthesis cup) can increase wear and lead to early revision. The position and coverage angle of the prosthesis cup influence the risk of edge loading. This study investigates the effect of altered gait patterns, more specific hip, and pelvis kinematics, on the orientation of hip contact force and the consequent risk of antero-superior edge loading using muscle driven simulations of gait. With a cup orientation of 25° anteversion and 50° inclination and a coverage angle of 168°, many gait patterns presented risk of edge loading. Specifically at terminal double support, 189 out of 405 gait patterns indicated a risk of edge loading. At this time instant, the high hip contact forces and the proximity of the hip contact force to the edge of the cup indicated the likelihood of the occurrence of edge loading. Although the cup position contributed most to edge loading, altering kinematics considerably influenced the risk of edge loading. Increased hip abduction, resulting in decreasing hip contact force magnitude, and decreased hip extension, resulting in decreased risk on edge loading, are gait strategies that could prevent edge loading. © 2015 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 34:1069-1076, 2016.

Can physical joint simulators be used to anticipate clinical wear problems of new joint replacement implants prior to market release?

One of the most important mandates of physical joint simulators is to provide test results that allow the implant manufacturer to anticipate and perhaps avoid clinical wear problems with their new products. This is best done before market release. This study gives four steps to follow in conducting such wear simulator testing. Two major examples involving hip wear simulators are discussed in which attempts had been made to predict clinical wear performance prior to market release. The second one, involving the DePuy ASR implant systems, is chosen for more extensive treatment by making it an illustrative example to explore whether wear simulator testing can anticipate clinical wear problems. It is concluded that hip wear simulator testing did provide data in the academic literature that indicated some risk of clinical wear problems prior to market release of the ASR implant systems. This supports the idea that physical joint simulators have an important role in the pre-market testing of new joint replacement implants.

High failure rate of the R3 metal-on-metal total hip arthroplasty

We report our failures with the use of the R3 metal-on-metal bearing. Forty six patients had an R3 acetabular system metal-on-metal THR in our centre between March 2007 and March 2009. All operations were performed using femoral components and appropriately matched femoral heads manufactured by Smith and Nephew. Twelve patients underwent revision surgery for adverse reaction to metal debris (ARMD). The median acetabular inclination was 40 degrees (range 21.1-49.1) and the median acetabular anteversion was 7.5 degrees (range 3.3-10.4). The median serum Cobalt was 9.9 µg/L (range 3.1-45) and the median serum Chromium was 5.8 µg/L (range 1.8-19.3). The time to revision was 39.2 months (range 13-53). Our current failure rate is 24%.

Clinical Performance of the ASR and ReCap Resurfacing Implants—7 Years Follow-Up

We perform a non-randomized, consecutive pilot study on the ASR and ReCap resurfacing hip implants and have completed 7 years follow-up. Forty-six non-osteoporotic patients with hip osteoarthritis and anatomical conditions suitable for resurfacing were divided into 2 equal groups and operated sequentially, starting with the ASR implants. Sixteen patients operated with ASR and 19 patients with ReCap have been followed-up. There were no significant differences between the two groups preoperatively as to physical function, pain, or femoral BMD. The serum concentrations of cobalt and chromium were higher in the ASR group from 1/2 to 7 years postoperatively. Five of 16 ASR implants have been revised, and none of the ReCap implants. BMD below the femoral component increased in both groups.

Femoral diameter and stem type are independent risk factors for ARMD in the large-headed ASR THR group

Background

Adverse soft-tissue reaction to metal debris (ARMD) continues to be major source of concern in metal-on-metal (MoM) hip replacements. In our earlier study we were able to establish several risk factors for ARMD in patients who had received a small-diameter (<50 mm) Articular Surface Replacement (ASR, DePuy, Warsaw, IN, USA). The aims of the present study were to analyze whether these previously established risk factors also apply to patients who have received a large-headed (>50 mm) ASR™ XL THR.

Methods

Large-headed ASR total hip replacements were used in 225 operations (196 patients) at our institution. 176 patients (203 hips) attended a screening programme, consisting of a clinical evaluation, whole blood cobalt and chromium measurements, and cross-sectional imaging.

Results

Revision surgery was performed on 84 hips (37%) in 75 patients. ARMD was diagnosed in the majority (n = 73 [87%]) of these revisions. Cumulative 8-year survivorship was 52%. The previously established risk factors for ARMD were not applicable. Interestingly, increasing femoral diameter and stem type were identified as independent risk factors for ARMD but reduced cup coverage had no significant association with ARMD.

Conclusions

Stem type and increasing femoral size as independent risk factors for ARMD in the cohort of ASR XL THR patients, support the importance of taper failure in the development of ARMD. The present results suggest that the degree of taper failure may be variable and dependent on the taper design.

Do hardened femoral heads reduce blood metal ion concentrations after hip resurfacing?

BACKGROUND

Elevated cobalt and chromium ion concentrations have been associated with the use of metal-on-metal bearings in hip arthroplasty. The use of a differential hardness bearing may reduce metal particle release. The aim of our study was to compare circulating cobalt (Co) and chromium (Cr) ion levels between patients treated with a standard all 'as-cast' heat treated bearing and a differential hardness bearing.

MATERIALS AND METHODS

One hundred and thirty-two patients implanted with unilateral hip resurfacing arthroplasties and having had blood metal ion studies performed between one and six years after surgery were retrospectively selected. There were 73 patients in the standard all 'as cast' heat treated bearing group (group 1) and 59 in the differential hardness bearing group (group 2).

RESULTS

Clinical and quality of life scores were comparable between groups. The median Co in group 1 was 1.01 µg/L and 1.23 µg/L in group 2 (p = 0.0566). The median Cr in group 1 was 1.60 µg/L and 1.34 µg/L in group 2 (p = 0.0505).

CONCLUSION

Compared with conventional heat-treated CoCr bearings, differential hardness metal-on metal bearings do not confirm in vivo the hopes of a substantial reduction in circulating metal ions concentrations suggested by in vitro wear studies.

The effect of contact load on CoCrMo wear and the formation and retention of tribofilms

Tribochemical reactions in a protein lubricated metal-on-metal (MoM) sliding contact may play a significant role for its wear performance. Such reactions lead to the formation of a carbonaceous 'tribofilm', which can act as a protective layer against corrosion and wear. The purpose of this study was to determine the effect of contact load on wear and the formation and retention of tribofilms. Wear tests were performed in a custom-made ball-on-flat testing apparatus that incorporated an electrochemical cell. A ceramic ball was used to articulate against low-carbon wrought CoCrMo alloy pins in bovine serum. Using a range of contact loads at a single potentiostatic condition (close to free potential), weight loss and changes in surface properties were evaluated. We determined that wear was influenced by the loading condition. As expected, wear increased with load, but the association between applied load and measured weight loss was not linear. In the intermediate load region, in the range of 32-48 N (~58-80 MPa), there was more than an order of magnitude drop in the wear per unit load, and the wear versus load data suggested an inflexion point at 49 N. Regression analyses yielded a cubic model (R²=0.991; p=0.0002), where the cubic term, which represents the inflexion, was highly significant (p=0.0021). This model is supported by the observations that the minimum in the friction versus load curve is at 52 N and the highest relative increase in polarization resistance occurred at 49 N. Scanning electron microscopy and Raman spectroscopy indicated the absence of a tribofilm for the low and within the contact area of the high load cases. Synergistic interactions of wear and corrosion seem to play an important role.

Two-year serum metal ion levels in minimally invasive total conservative hip resurfacing: preliminary results of a prospective study

BACKGROUND

Metal-on-metal (MoM) hip resurfacings have been associated with the potential development of metallic debris and its associated pathology. Serum cobalt and chromium levels are a reliable surrogate marker of wear rates in MoM bearings. The aim of the study was to examine the trend in serum metal ion levels in the initial 2-year post-operative period following implantation of the minimally invasive total conservative hip MoM hip resurfacing and to determine whether head size, acetabular component orientation, clinical outcome scores or post-operative range of movement would affect these levels.

METHODS

In this prospective cohort study, serum cobalt and chromium ion levels were measured pre- and post-operatively in 25 patients who underwent minimally invasive total conservative hip MoM hip resurfacing. The results were correlated with acetabular component orientation, head size, outcome scores and post-operative range of movement.

RESULTS

The mean serum cobalt and chromium levels at 2 years were 1.2 ppb (0.4-4.4 ppb) and 2.1 ppb (0.7-5.7 ppb). The mean cup inclination was 43° (30°-60°) and anteversion was 18° (1°-47°). There was no clear relationship between serum ions and acetabular component orientation, outcome scores or range of movement. Patients with a head size ≤52 mm had significantly higher metal ion levels (cobalt P = 0.02, chromium P = 0.045).

CONCLUSION

Our preliminary results show all patients had cobalt and chromium levels below those indicating a high-risk implant, suggesting successful early outcome from minimally invasive total conservative hip resurfacing surgery.

Outcome of Birmingham hip resurfacing at ten years: role of routine whole blood metal ion measurements in screening for pseudotumours

PURPOSE

Emerging concern has arisen because of recent papers reporting a high prevalence of pseudotumours (PTs), even in patients with surface arthroplasties with a good clinical track record. The aim of our study was to establish the ten year survivorship of Birmingham hip resurfacing (BHR), to investigate whole blood (WB) metal ion levels and prevalence of adverse reactions to metal debris (ARMeD) and to determine the association of blood metal ion levels and symptoms with ARMeD in patients operated on with BHR at our institution.

METHODS

Between May 2001 and May 2004, 261 consecutive BHRs were implanted in 219 patients. All living, nonrevised patients underwent a systematic screening programme consisting of clinical examination, WB cobalt and chromium measurements and targeted cross-sectional imaging.

RESULTS

The ten year survival for the entire cohort was 91% (89-93%), with any revision as the endpoint. Prevalence of ARMeD was 6.9% in male and 8.8% in female patients. Symptomatic patients with elevated metal ion levels evinced highest prevalence (63%) of PTs compared with asymptomatic patients with elevated metal ion levels (42%) and symptomatic patients with nonelevated metal ions (11%).

CONCLUSIONS

Contradicting the current international guidelines, our results suggest that it seems beneficial to combine routine metal ion measurement with clinical assessment, even in patients with well-functioning BHRs. Further follow-up will reveal whether new PTs will develop in these patients and BHR survivorship in the longer term.

High metal ion levels after use of the ASR™ device correlate with development of pseudotumors and T cell activation

BACKGROUND

Pseudotumors and immunologic alterations are reported in patients with elevated metal ion levels after resurfacing arthroplasty of the hip. A direct association of increased cobalt and chromium concentrations with the development of pseudotumors has not been established.

QUESTIONS/PURPOSES

We hypothesized that (1) patients with higher blood cobalt and chromium concentrations are more likely to have pseudotumors develop, (2) elevated cobalt and chromium concentrations correlate with increased activation of defined T cell populations, and (3) elevated metal ion levels, small implant size, cup inclination angle, and patient age are risk factors for the development of pseudotumors.

METHODS

A single-surgeon cohort of 78 patients with 84 Articular Surface Replacement(®) implants was retrospectively investigated. Between 2006 and 2010, we performed 84 THAs using the Articular Surface Replacement(®) implant; this represented 2% (84/4950) of all primary hip replacements performed during that period. Of the procedures performed using this implant, we screened 77 patients (99%) at a mean of 43 months after surgery (range, 24-60 months). Seventy-one patients were investigated using ultrasound scanning, and cobalt and chromium concentrations in whole blood were determined by high-resolution inductively coupled plasma mass spectrometry. Differential analysis of lymphocyte subsets was performed by flow cytometry in 53 patients. Results of immunologic analyses were investigated separately for patients with and without pseudotumors. Pseudotumors were found in 25 hips (35%) and were more common in women than in men (p = 0.02). Multivariable regression analysis was performed to identify risk factors for the development of pseudotumors.

RESULTS

Cobalt and chromium concentrations were greater in patients with pseudotumors than in those without (cobalt, median 8.3 versus median 1.0 μg/L, p < 0.001; chromium, median 5.9 versus median 1.3 μg/L, p < 0.001). The percentage of HLA-DR(+)CD4(+) T cells was greater in patients with pseudotumors than in those without (p = 0.03), and the proportion of this lymphocyte subtype was positively correlated with cobalt concentrations (r = 0.3, p = 0.02). Multivariable regression analysis indicated that increasing cobalt levels were associated with the development of pseudotumors (p < 0.001), and that patients with larger implants were less likely to have them develop (p = 0.04); age and cup inclination were not risk factors.

CONCLUSIONS

We found a distinct association of elevated metal ion concentrations with the presence of pseudotumors and a correlation of increased cobalt concentrations with the proportion of activated T helper/regulator cells. Thus, the development of soft tissue masses after metal-on-metal arthroplasty could be accompanied by activation of T cells, indicating that this complication may be partly immunologically mediated. Further investigations of immunologic parameters in larger cohorts of patients with metal-on-metal arthroplasties are warranted.

LEVEL OF EVIDENCE

Level III, therapeutic study. See the Instructions for Authors for a complete description of levels of evidence.

Accuracy of methods for calculating volumetric wear from coordinate measuring machine data of retrieved metal-on-metal hip joint implants

This study compared the accuracy and sensitivity of several numerical methods employing spherical or plane triangles for calculating the volumetric wear of retrieved metal-on-metal hip joint implants from coordinate measuring machine measurements. Five methods, one using spherical triangles and four using plane triangles to represent the bearing and the best-fit surfaces, were assessed and compared on a perfect hemisphere model and a hemi-ellipsoid model (i.e. unworn models), computer-generated wear models and wear-tested femoral balls, with point spacings of 0.5, 1, 2 and 3 mm. The results showed that the algorithm (Method 1) employing spherical triangles to represent the bearing surface and to scale the mesh to the best-fit surfaces produced adequate accuracy for the wear volume with point spacings of 0.5, 1, 2 and 3 mm. The algorithms (Methods 2-4) using plane triangles to represent the bearing surface and to scale the mesh to the best-fit surface also produced accuracies that were comparable to that with spherical triangles. In contrast, if the bearing surface was represented with a mesh of plane triangles and the best-fit surface was taken as a smooth surface without discretization (Method 5), the algorithm produced much lower accuracy with a point spacing of 0.5 mm than Methods 1-4 with a point spacing of 3 mm.

The current state of bearing surfaces in total hip replacement

We reviewed the literature on the currently available choices of bearing surface in total hip replacement (THR). We present a detailed description of the properties of articulating surfaces review the understanding of the advantages and disadvantages of existing bearing couples. Recent technological developments in the field of polyethylene and ceramics have altered the risk of fracture and the rate of wear, although the use of metal-on-metal bearings has largely fallen out of favour, owing to concerns about reactions to metal debris. As expected, all bearing surface combinations have advantages and disadvantages. A patient-based approach is recommended, balancing the risks of different options against an individual’s functional demands.

Cite this article: Bone Joint J 2014;96-B:147–56.

Predicting wear and blood metal ion levels in metal-on-metal hip resurfacing

Suboptimal component position and design are thought to lead to edge wear and raised blood metal ion levels in metal-on-metal hip resurfacing (MOM-HR). These factors are thought to influence the "contact patch to rim distance" (CPRD), and calculation of this distance may improve prediction of wear and blood metal ion levels. We measured blood cobalt and chromium ion levels and the wear rates of the bearing surfaces in 165 MOM-HR retrieval cases. We then determined the contribution and effect sizes of cup inclination and version angles, component size and design, and CPRD (calculated from case-specific data) on blood metal ion levels and component wear rates. Acetabular orientation explained between 16.3% and 28.5% of the variation in wear rates and metal ion levels, whereas component size and design explained between 7.3% and 21.8% of the variability. In comparison, CPRD explained up to 67.7% of the variability, significantly greater than any other variable (all p < 0.0001). CPRD is a good predictor of wear and improves our understanding of wear performance and the mechanisms leading to edge loading.

Hip abduction can prevent posterior edge loading of hip replacements

Edge loading causes clinical problems for hard-on-hard hip replacements, and edge loading wear scars are present on the majority of retrieved components. We asked the question: are the lines of action of hip joint muscles such that edge loading can occur in a well-designed, well-positioned acetabular cup? A musculoskeletal model, based on cadaveric lower limb geometry, was used to calculate for each muscle, in every position within the complete range of motion, whether its contraction would safely pull the femoral head into the cup or contribute to edge loading. The results show that all the muscles that insert into the distal femur, patella, or tibia could cause edge loading of a well-positioned cup when the hip is in deep flexion. Patients frequently use distally inserting muscles for movements requiring deep hip flexion, such as sit-to-stand. Importantly, the results, which are supported by in vivo data and clinical findings, also show that risk of edge loading is dramatically reduced by combining deep hip flexion with hip abduction. Patients, including those with sub-optimally positioned cups, may be able to reduce the prevalence of edge loading by rising from chairs or stooping with the hip abducted.

Taper corrosion in modular hip prostheses: analysis of serum metal ions in 19 patients

Recently, concerns have been raised about the use of metal-on-metal (MoM) implants. This has led to the recall of several resurfacing and large-diameter total hip arthroplasties (THA). Any MoM interface can be the cause of metal debris and adverse tissue reactions. We analyzed serum metal ions and HOOS scores in 19 of 306 patients treated with a THA with modular neck section. The only MoM interface in this particular implant is the taper between the neck and the stem. The articulating surface consists of a ceramic-on-polyethylene or ceramic-on-ceramic interface. As such, this study looks at the metal ion production from the modular neck section. One of 306 implants needed revision at 52-month follow-up because of an adverse reaction to metal debris (ARMD).

A biomechanical study of the Birmingham mid head resection arthroplasty: effect of stem size on femoral neck fracture

The Birmingham mid head resection (BMHR) arthroplasty can be used as an alternative to conventional stemmed total hip arthroplasty in young patients unsuitable for hip resurfacing. This study investigated the effect of stem size on femoral neck fracture in the BMHR. Sawbones composite femurs were randomly allocated to one of the following groups: (1) unprepared femur with no prosthesis, (2) femur prepared with a Birmingham hip resurfacing (BHR) prosthesis, (3) femur prepared with a BMHR stem size 1 (BMHR-1) and (4) femur prepared with a BMHR stem size 3 (BMHR-3). Each femur was subjected to a compressive force using a materials testing machine until fracture of the femoral neck occurred. The highest force at fracture was in the unprepared femurs with a mean (±standard deviation) force at failure of 5.9 ± 0.2 kN. The mean force at failure for the femurs fitted with a prosthesis was 2.6 ± 0.4, 3.0 ± 0.4 and 3.5 ± 0.5 kN for the BHR, BMHR-1 and BMHR-3, respectively. Statistical analysis showed that the failure force for the unprepared femur was significantly (p<0.05) greater than that of the BHR, BMHR-1 and BMHR-3. There was a significant difference (p<0.05) between the force at failure for the BMHR-1 and BMHR-3, indicating that these two stem sizes have an effect on fracture force.

The role of biomechanics and engineering in total hip replacement. Why surgeons need technical help

Implanting the acetabular cup of hard-on-hard bearings, like metal-on-metal or ceramic-on-ceramic, requires considerable surgeon skill to avoid the complications associated with edge loading. Successful cup positioning instruments have been designed in the past by pioneering surgeons, like Peter Ring and Michael Freeman, and these are re-visited in this article. An advantage of these instruments is that they could position the acetabular cup without defining a reference pelvic plane. Computer-assisted cup orientation is able to reduce outliers in cup orientation, but the technology has not been widely adopted. There may be an opportunity to improve the uptake of computer-assisted surgery by incorporating some of the concepts from historically successful manual instruments.

[Principles of tribological analysis of endoprostheses]

For the tribological characterization of artificial joints, various experimental methods are currently available. However, the in vitro test conditions applied are only comparable in a limited way and transferability to the in vivo situation is also restricted. This is due to the different wear simulation concepts used and partly insufficient simulation of clinical worst case situations. In the present paper current scientific methods and procedures for tribological testing of artificial joints are presented. In addition, the biological effects of wear products are described enabling clinicians to challenge tribological studies and to facilitate specific interpretation of scientific results taking the clinical situation into account.

Application of a falsification strategy to a musculoskeletal model of the lower limb and accuracy of the predicted hip contact force vector

In the literature, lower limb musculoskeletal models validated against in vivo measured hip contact forces (HCFs) exhibit a tendency to overestimate the HCFs magnitude and predict inaccurate components of the HCF vector in the transverse plane. In order to investigate this issue, a musculoskeletal model was forced to produce HCFs identical to those measured and the resulting joint equilibrium equations were studied through both a general approach and a static optimization framework. In the former case, the existence of solutions to the equilibrium equations was investigated and the effect of varying the intersegmental moments and the muscle tetanic stress assessed: for a value of 100 N/cm(2) and moments calculated from an inverse dynamics analysis on average only 62% of analyzed frames were solvable for level walking and 70% for stair climbing. In the static optimization study, the model could reproduce the experimental HCFs but the recruited muscles were unable to simultaneously equilibrate the hip intersegmental moments without the contribution of reserve moment actuators. Without constraints imposed on the HCFs, the predicted HCF vectors presented maximum angle deviations up to 22° for level walking and 33° for stair climbing during the gait stance phase. The influence of the medio-lateral HCF component on the solvability of the equilibrium equations and the muscle recruitment alteration when the model was forced to produce the experimental HCFs suggest that a more accurate geometrical representation of the gluteal muscles is mandatory to improve predictions of the HCF vector yielded by the static optimization technique.

Wear in metal-on-metal total disc arthroplasty

The wear of a model metal-on-metal ball-and-socket total disc arthroplasty was measured in a simulator. The ball had a radius of 10 mm, and there was a radial clearance between ball and socket of 0.015 mm. The model was subjected to simultaneous flexion–extension, lateral bending, axial rotation (frequency: 1 Hz) and compression (frequency: 2 Hz, maximum load: 2 kN). Throughout the tests, the models were immersed in calf serum diluted to a concentration of 15 g protein per litre, at a controlled temperature of 37 °C. Tests were performed on three models. At regular intervals (0, 0.5, 1, 2, 3, 4 and 5 million cycles), mass and surface roughness were determined; mass measurements were converted into the volume lost as a result of wear. All measurements were repeated six times. Wear occurred in two stages. In the first stage (duration about 1 million cycles), there was a linear wear rate of 2.01 ± 0.04 mm3 per million cycles; in the second stage, there was a linear wear rate of 0.76 ± 0.02 mm3 per million cycles. Surface roughness increased linearly in the first million cycles and then continued to increase linearly but more slowly.