Adsorption properties of tetracycline onto graphene oxide: equilibrium, kinetic and thermodynamic studies

The fate of antibiotics during phosphate recovery processes - A critical review

The principles of circular economy encourage the recovery of phosphorus from nutrient-rich waste streams such as animal manure, domestic wastewater, and urine to supplement existing sources of raw phosphorus. However, these waste streams also contain a wide variety of contaminants of emerging concern including antibiotics, and the recovery of phosphorus from these waste streams results in the co-occurrence of antibiotics with the recovered phosphorus products. This paper provides a comprehensive overview of the fate of environmentally relevant antibiotics in three major existing and upcoming phosphorus recovery processes: precipitation-, membrane-, and adsorption-based treatment. In general, the co-occurrence of antibiotics in recovered phosphorus increases with the presence of dissolved organic matter (DOM) and cations due to π-π interaction and cationic bridge formation, respectively. Additionally, antibiotics display pH-based speciation resulting in electrostatic interactions with recovered phosphorus at pH > 7.0. Furthermore, this critical review establishes a new metric, the relative antibiotic-to‑phosphorus (RAP), defined as the ratio of the concentration of antibiotics to phosphorus in recovered phosphorus to that of the phosphorus-rich waste. Precipitation-based methods, particularly struvite, demonstrated the lowest RAP, while the RAP in carbon-based adsorbents was 1.8 × 108 times higher than in membrane-based processes. In reviewing literature on the fate of antibiotics in phosphorus recovery processes, several research needs are also highlighted: the fate of non-tetracycline antibiotics, simultaneous investigation of phosphorus and antibiotic fate in membrane- and adsorption-based methods, treatment methods to mitigate the co-occurrence of antibiotics in recovered phosphorus product, and the release of antibiotics from recovered phosphate products.

Emerging Nanomaterials for Drinking Water Purification: A New Era of Water Treatment Technology

The applications of nanotechnology in the field of water treatment are rapidly expanding and have harvested significant attention from researchers, governments, and industries across the globe. This great interest stems from the numerous benefits, properties, and capabilities that nanotechnology offers in addressing the ever-growing challenges related to water quality, availability, and sustainability. This review paper extensively studies the applications of several nanomaterials including: graphene and its derivative-based adsorbents, CNTs, TiO2 NPs, ZnO NPs, Ag NPs, Fe NPs, and membrane-based nanomaterials in the purification of drinking water. This, it is hoped, will provide the water treatment sector with efficient materials that can be applied successfully in the water purification process to help in addressing the worldwide water scarcity issue.

Distinctive effects of graphene oxide and reduced graphene oxide on methane production kinetics and pharmaceuticals removal in anaerobic reactors

Graphene oxide (GO) addition to anaerobic digestion has been suggested to enhance direct electron transfer. The impact of GO (0.075 g GO g-1 VS) and biologically and hydrothermally reduced GO (bio-rGO and h-rGO, respectively) on the methane production kinetics and removal of 12 pharmaceuticals was assessed in Fed-batch reactors. A decrease of 15 % in methane production was observed in the tests with GO addition compared with the control and the h-rGO. However, bio-rGO and h-rGO substantially increased the methane production rate compared to the control tests (+40 %), in the third fed-batch test. Removal of pharmaceuticals was enhanced only during the bio-reduction of GO (1st fed-batch test), whereas once the GO was bio-reduced, it followed a similar trend in the control and h-rGO tests. The addition of GO can enhance the methane production rate and, therefore, reduce the anaerobic treatment time.

Removal of amoxicillin from contaminated water using modified bentonite as a reactive material

This study concerns the removal of a trihydrate antibiotic (Amoxicillin) from synthetically contaminated water by adsorption on modified bentonite. The bentonite was modified using hexadecyl trimethyl ammonium bromide (HTAB), which turned it from a hydrophilic to a hydrophobic material. The effects of different parameters were studied in batch experiments. These parameters were contact time, solution pH, agitation speed, initial concentration (C0) of the contaminant, and adsorbent dosage. Maximum removal of amoxicillin (93 %) was achieved at contact time = 240 min, pH = 10, agitation speed = 200 rpm, initial concentration = 30 ppm, and adsorbent dosage = 3 g bentonite per 1L of pollutant solution. The characterization of the adsorbent, modified bentonite, was accomplished using Fourier transform infrared spectroscopy, scanning electron microscopy, X-ray diffraction, and Brunauer-Emmett-Teller. The isotherm models were also investigated, and it was found that the Freundlich isotherm model fitted well with the experimental data (R2 = 94.77), which suggests heterogeneity in the multilayer adsorption of amoxicillin onto modified bentonite. The kinetics of the adsorption process were studied. The experimental data were found to obey the pseudo-first-order kinetic model (R2 = 95.1). Thermodynamic studies indicated that the adsorption process was physisorption and endothermic. Finally, the modified bentonite proved to be a good adsorbent for the removal of amoxicillin from contaminated solutions.

Modified Diatomaceous Earth in Heparin Recovery from Porcine Intestinal Mucosa

Heparin, a highly sulfated glycosaminoglycan, is a naturally occurring anticoagulant that plays a vital role in various physiological processes. The remarkable structural complexity of heparin, consisting of repeating disaccharide units, makes it a crucial molecule for the development of commercial drugs in the pharmaceutical industry. Over the past few decades, significant progress has been made in the development of cost-effective adsorbents specifically designed for the adsorption of heparin from porcine intestinal mucosa. This advancement has been driven by the need for efficient and scalable methods to extract heparin from natural sources. In this study, we investigated the use of cationic ammonium-functionalized diatomaceous earth, featuring enhanced porosity, larger surface area, and higher thermal stability, to maximize the isolated heparin recovery. Our results showed that the higher cationic density and less bulky quaternary modified diatomaceous earth (QDADE) could adsorb up to 16.3 mg·g-1 (31%) of heparin from the real mucosa samples. Additionally, we explored the conditions of the adsorbent surface for recovery of the heparin molecule and optimized various factors, such as temperature and pH, to optimize the heparin uptake. This is the introductory account of the implementation of modified diatomaceous earth with quaternary amines for heparin capture.

Detection of protamine based on competitive adsorption onto the surface of functionalized multi-walled carbon nanotubes

This study developed an adsorption-based determination system for protamine. A multi-walled carbon nanotube (MWCNT), which is a strong adsorbent, was used. The competitive adsorption process between dyes and protamine formed the basis of the sensor system. The adsorption process was followed over the dyes by UV-Vis. absorption spectroscopy. This sensor system was developed using the thermodynamic parameters. Transmission electron microscopy and Fourier-transform infrared spectroscopy techniques were used for the characterization of the sensor system. It was determined that the sensor system remained stable at physiological temperature and pH range. Limit of detection values of PyB-COO-MWCNT and PyY-COO-MWCNT systems were found to be 1.32 and 1.12 ng mL-1 , respectively. The applicability of the sensor systems was demonstrated using bovine serum solutions.

Preparation and Evaluation of Aminomalononitrile-Coated Ca-Sr Metal-Organic Frameworks as Drug Delivery Carriers for Antibacterial Applications

After orthopedic surgery, antibiotics are usually employed to reduce the risk of infection. If it is possible to enhance antimicrobial functionality and incorporate antimicrobial agents into the bone-filling matrix, not only it can promote bone tissue regeneration, but it can also enable localized administration of medication to elevate antibacterial efficacy. Meanwhile, previous studies have shown that calcium and strontium can support the growth of osteoblastic cells and diminish bone resorption or deterioration. In the past few years, metal-organic frameworks (MOFs) have been widely used as drug carriers owing to their characteristic advantages. In this study, a MOF was prepared in an aqueous solution by a simple coprecipitation method with the organic ligand 1,3,5-tricarboxylic benzene (H3BTC) as a linker to form Ca-Sr-MOF. Furthermore, the Ca-Sr-MOF was coated with aminomalononitrile (AMN), which adhered through the electrostatic interactions between H3BTC and AMN. With this MOF (Ca-Sr-AMN-MOF), AMN polymerization reactions can occur in aqueous environments, and a polymer layer was observed on the MOF surface with moderate hydrophilicity. The prepared Ca-Sr-MOF and Ca-Sr-AMN-MOF were characterized by Fourier transform infrared spectroscopy, powder X-ray diffraction, scanning electron microscopy, high-resolution transmission electron microscopy, and UV-visible spectroscopy. Finally, tetracycline (TC) was selected as the model drug to measure the drug loading efficiency, release profile, and antibiotic activity. The percent cumulative drug release of TC from Ca-Sr-MOF and Ca-Sr-AMN-MOF was 55.15 and 9.1%, respectively. The antibacterial effectiveness of TC-loaded MOF against Gram-negative Escherichia coli bacteria was evaluated, revealing the remarkable antimicrobial performance of these substances.

Efficient and Economic Heparin Recovery from Porcine Intestinal Mucosa Using Quaternary Ammonium-Functionalized Silica Gel

Heparin, usually isolated from porcine intestinal mucosa, is an active pharmaceutical ingredient of great material value. Traditionally, diverse types of commercial resins were employed as an adsorbent for heparin retrieval from biological samples. However, more recent years have encouraged the advent of new cost-effective adsorbents to achieve enhanced heparin retrieval. Inexpensive cationic ammonium-functionalized silica gels, monodispersed with larger surface area, porosity, and higher thermal stability, were chosen to evaluate the heparin recovery yield from porcine intestinal mucosa. We demonstrated that higher positively charged and less bulky quaternary modified silica gel (e.g., QDASi) could adsorb ~28% (14.7 mg g-1) heparin from the real samples. In addition, we also determined suitable surface conditions for the heparin molecule adsorption by mechanistic studies and optimized different variables, such as pH, temperature, etc., to improve the heparin adsorption. This is going to be the first reported study on the usage of quaternary amine-functionalized silica gel for HEP uptake.

Two-dimensional activated carbon nanosheets for rapid removal of tetracycline via strong π-π electron donor receptor interactions

Two-dimensional carbonaceous materials have sparked extensive attention in organic pollutants adsorption due to their unique structure to facilitate the formation of the physical or chemical bonding. Herein, natural two-dimensional porous activated carbon nanosheets with ultra-high specific surface area (2276.44 m² g^-1) are prepared by alkaline immersion-assisted circulating calcination techniques from corn straw piths. The prepared nanosheets exhibit rapid tetracycline adsorption capacity (633 mg g^-1 within 5 min) and high equilibrium adsorption capacity of 804.5 mg g^-1. Significantly, the nanosheets can adapt to a wide range of pH (at least between pH = 3-10) and are almost unaffected by coexisting ions. Mechanism studies and theoretical calculations demonstrate that the rapid and high-efficient adsorption of tetracycline mainly depends on the π-π electron donor receptor interactions. In addition, hydrogen bonding and pore filling was also responsible for tetracycline adsorption. This work provides important guidance for the development of the biobased high-performance adsorbents from agricultural waste.

Integrated ultrasound-assisted magnetic solid-phase extraction for efficient determination and pre-concentration of polycyclic aromatic hydrocarbons from high-consumption soft drinks and non-alcoholic beers in Iran

In the present research, an ultrasound-assisted magnetic solid-phase extraction coupled with a gas chromatography-mass spectrometry hybrid system was developed for extraction/determination of trace amounts of polycyclic aromatic hydrocarbons in high-consumption soft drinks and non-alcoholic beers in Iran using magnetite graphene oxide adsorbent. The magnetite graphene oxide was characterized by scanning electron microscope, transmission electron microscopy, Fourier-transform infrared spectroscopy, X-ray diffraction, and vibrating-sample magnetometer techniques. The highest extraction recovery (73.05 to 95.56%) and enrichment factor (90.65 to 106.38) were obtained at adsorbent mass: 10 mg, adsorption time: 30 min, salt addition: sodium chloride 10% w/v, desorption time: 20 min, eluent type: hexane: acetone (1:1, v/v), and desorption solvent volumes: 200 μL. Under optimum conditions, the linearity range for polycyclic aromatic hydrocarbons determination was 0.2-200 ng mL^-1  with coefficient of determination> 0.993, limit of detection = 0.09-0.21 ng mL^-1 , limit of quantitation = 0.3-0.7 ng mL^-1 , and relative standard deviation < 8.1%, respectively. Relative recoveries in spiked real samples ranged from 94.67 to 109.45 % with standard deviation < 6.05%. The proposed method is effective, sensitive, reusable and it is promising for the analysis of polycyclic aromatic hydrocarbons residues in environmental samples. This article is protected by copyright. All rights reserved.

Chitosan magnetic graphene grafted polyaniline doped with cobalt oxide for removal of Arsenic(V) from water

The present study reports the successful functionalization/magnetization of bio-polymer to produce chitosan-magnetic graphene oxide grafted polyaniline doped with cobalt oxide (ChMGOP-Co₃O₄). Analytical techniques furrier transform infra-red (FT-IR), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS) were used to confirm the formation of ChMGOP-Co₃O₄. The effects of several experimental factors (solution pH, adsorbent dosage and coexisting ions) on the uptake of As(V) ions using ChMGOP-Co₃O₄ were examined through batch experiments. As(V) removal process was validated by experimentally and theoretically investigating the adsorption capacity, rate, and thermal effects. Thermodynamic parameters such as free energy (ΔG°), entropy (ΔS°) and enthalpy (ΔH°) were also calculated and were used to explain the mechanism of adsorption. Based on the results, the sorbent showed a high adsorption capacities (90.91 mg/g) at favorable neutral pH and superior removal efficiencies as high as 89% within 50 min. In addition, the adsorption isotherm followed the Langmuir isotherm in compare to the Freundlich, due to its higher R² value (0.992 < 0.941). Meanwhile, the kinetic data revealed that the of As(V) adsorption was controlled by pseudo-second-order. Overall, the adsorption mechanism studies revealed a spontaneous endothermic nature with predominance of physisorption over chemisorption. This study indicated that ChMGOP-Co₃O₄ is an exceptional novel adsorbent material for the efficient isolation of As(V) from aqueous media.

Efficient Heparin Recovery from Porcine Intestinal Mucosa Using Zeolite Imidazolate Framework-8

Heparin is one of the most valuable active pharmaceutical ingredients, and it is generally isolated from porcine intestinal mucosa. Traditionally, different types of commercial resins are employed as an adsorbent for heparin uptake; however, using new, less expensive adsorbents has attracted more interest in the past few years to enhance the heparin recovery. Zeolite imidazolate framework-8 (ZIF-8), as a metal–organic framework (MOF) with a high surface area, porosity, and good stability at high temperatures, was selected to examine the heparin recovery. In this research, we demonstrate that ZIF-8 can recover up to ~70% (37 mg g⁻¹) of heparin from porcine intestinal mucosa. A mechanistic study through kinetic and thermodynamic models on the adsorption revealed appropriate surface conditions for the adsorption of heparin molecules. The effect of different variables such as pH and temperature on heparin adsorption was also studied to optimize the recovery. This study is the first to investigate the usage of MOFs for heparin uptake.

Adsorptive removal of noxious atrazine using graphene oxide nanosheets: Insights to process optimization, equilibrium, kinetics, and density functional theory calculations

Atrazine is a toxic herbicide whose alarming rate of contamination in the drinking water and wastewater poses a severe threat to the environment and human health. Here in this study, the graphene oxide (GO) nanosheets were prepared using Hummers' method with minor modification and studied as a potential adsorbent for atrazine removal from simulated wastewater. The spectroscopy and microscopic analysis confirmed the successful formation of GO with a multilayer structure resembling the crumpled sheets with random stacking. The Response Surface Methodology (RSM) employing Box Behnken design (BBD) was successfully developed to predict the optimal conditions for maximal atrazine removal as adsorbent dosage 121.45 mg/L; initial feed concentration 27.03 mg/L; temperature 27.69 °C, pH 5.37, and time 180 min. The atrazine adsorption onto GO was found to be higher in acidic pH and lower temperature. Density functional theory (DFT) calculation of adsorbent-adsorbate complex in the implicit solvent medium suggests adsorption affinity energy of -24.4 kcal/mol for atrazine. A careful observation of the molecules configuration and binding energy showed that the π-π interactions and hydrogen bonds played a significant role in the adsorption phenomena. Langmuir isotherm suited well to the adsorption process with a maximum adsorption capacity of 138.19 mg/g, at 318 K. The fitness of kinetic models for atrazine adsorption onto GO nanosheets were in following order Ho < Sobkowsk-Czerwi < Avrami model based on their correlation coefficient (R²) values. Reusability analysis showed that GO nanosheets could be effectively recycled using 0.01 N NaOH up to six cycles of atrazine removal. Thus, this study provided a theoretical and experimental basis for the potential application of GO nanosheets as a novel adsorbent for the removal of hazardous atrazine.

Potentiation of Antimicrobial Photodynamic Therapy by Curcumin Loaded Graphene Quantum Dots

Increasing resistance to existing antibiotics by microbes is currently the biggest dilemma. Antimicrobial photodynamic therapy is a promising alternative for treatment of multidrug resistant infections. The aim of current study was to fabricate graphene quantum dots loaded with curcumin as photosensitizer for improved antimicrobial photodynamic therapy. The study involved fabrication of blank and curcumin-loaded graphene quantum dots, their characterizations (TEM, UV-visible & fluorescence emission spectra), cytotoxicity assay, ROS assay and investigation of enhanced antimicrobial photodynamic effect against resistant microbes. The fabrication of blank and loaded graphene quantum dots was confirmed by observation of peak shift and changes in peak intensity of blank graphene quantum dots, curcumin alone compared to curcumin loaded graphene quantum dots in UV-visible and fluoresce emission spectra. Cytotoxicity assay showed that 100 µM concentration was not toxic to NIH/3t3 fibroblasts. In ROS assay, the curcumin loaded formulation showed threefold increase in ROS production. Blue light (405 nm) irradiance of 30 J/cm² and photosensitizer concentration of 100 µM showed ~3.5 log₁₀ enhanced CUF reduction against Pseudomonas aeruginosa, MRSA, Escherichia coli, and Candida albicans. In conclusion, curcumin-loaded graphene quantum dots shoed enhanced antimicrobial photodynamic effects and can be used as an alternative effective treatment for resistant infections.

Tetracycline Antibiotics: Elucidating the Electrochemical Fingerprint and Oxidation Pathway

Herein, a complete study of the electrochemical behavior of the most commonly used tetracycline antibiotics (TCs) on unmodified carbon screen-printed electrodes (SPEs) is presented. In addition, the oxidation pathway of TCs on SPE is elucidated, for the first time, with liquid chromatography-quadrupole time-of-flight mass spectrometry (LC-QTOF-MS). Square wave voltammetry (SWV) was used to study the electrochemical fingerprint (EF) of the antibiotics shaping the different oxidation processes of the TCs in a pH range from 2 to 12. Their characteristic structure and subsequent EF offer the possibility of distinguishing this class of antibiotics from other types. Under the optimized parameters, calibration curves of tetracycline (TET), doxycycline (DOXY), oxytetracycline (OXY), and chlortetracycline (CHL) in a Britton Robinson buffer solution (pH 9) exhibited a linear range between 5 and 100 µM with excellent reproducibilities (RSDTET = 3.01%, RSDDOXY = 3.29%, RSDOXY = 9.78% and RSDCHL = 6.88% at 10 µM, N = 3) and limits of detection (LOD) of LODTET = 4.15 µM, LODDOXY = 2.14 µM, LODOXY = 3.07 µM and LODCHL = 4.15 µM. Furthermore, binary, tertiary, and complex mixtures of all TCs were analyzed with SWV to investigate the corresponding EF. A dual pH screening (pH 4 and pH 9), together with the use of a custom-made Matlab script for data treatment, allowed for the successful confirmation of a single presence of TCs in the unknown samples. Overall, this work presents a straightforward study of the electrochemical behavior of TCs in SPE, allowing for the future on-site identification of residues of tetracycline antibiotics in real samples.

Graphene Oxide Nanoparticles Modified Paper Electrode as a Biosensing Platform for Detection of the htrA Gene of O. tsutsugamushi

The unique structural and electrochemical properties of graphene oxide (GO) make it an ideal material for the fabrication of biosensing devices. Therefore, in the present study, graphene oxide nanoparticles modified paper electrodes were used as a low-cost matrix for the development of an amperometric DNA sensor. The graphene oxide was synthesized using the modified hummers method and drop cast on a screen-printed paper electrode (SPPE) to enhance its electrochemical properties. Further, the GO/SPPE electrode was modified with a 5′NH2 labeled ssDNA probe specific to the htrA gene of Orientia tsutsugamushi using carbodiimide cross-linking chemistry. The synthesized GO was characterized using UV-Vis, FTIR, and XRD. The layer-by-layer modification of the paper electrode was monitored via FE-SEM, cyclic voltammetry, and electrochemical impedance spectroscopy (EIS). The sensor response after hybridization with single-stranded genomic DNA (ssGDNA) of O. tsutsugamushi was recorded using differential pulse voltammetry (DPV). Methylene blue (1 mM in PBS buffer, pH 7.2) was used as a hybridization indicator and [Fe(CN)₆]^−3/−4 (2.5 mM in PBS buffer, pH 7.2) as a redox probe during electrochemical measurements. The developed DNA sensor shows excellent sensitivity (1228.4 µA/cm²/ng) and LOD (20 pg/µL) for detection of O. tsutsugamushi GDNA using differential pulse voltammetry (DPV).

Effective Poly (Cyclotriphosphazene-Co-4,4'-Sulfonyldiphenol)@rGO Sheets for Tetracycline Adsorption: Fabrication, Characterization, Adsorption Kinetics and Thermodynamics

The development of excellent drug adsorbents and clarifying the interaction mechanisms between adsorbents and adsorbates are greatly desired for a clean environment. Herein, we report that a reduced graphene oxide modified sheeted polyphosphazene (rGO/poly (cyclotriphosphazene-co-4,4'-sulfonyldiphenol)) defined as PZS on rGO was used to remove the tetracycline (TC) drug from an aqueous solution. Compared to PZS microspheres, the adsorption capacity of sheeted PZS@rGO exhibited a high adsorption capacity of 496 mg/g. The adsorption equilibrium data well obeyed the Langmuir isotherm model, and the kinetics isotherm was fitted to the pseudo-second-order model. Thermodynamic analysis showed that the adsorption of TC was an exothermic, spontaneous process. Furthermore, we highlighted the importance of the surface modification of PZS by the introduction of rGO, which tremendously increased the surface area necessary for high adsorption. Along with high surface area, electrostatic attractions, H-bonding, π-π stacking and Lewis acid-base interactions were involved in the high adsorption capacity of PZS@rGO. Furthermore, we also proposed the mechanism of TC adsorption via PZS@rGO.

Effective degradation of tetracycline by manganese peroxidase producing Bacillus velezensis strain Al-Dhabi 140 from Saudi Arabia using fibrous-bed reactor

A tetracycline degrading bacterial strains was characterized from the municipal sludge and detected its ability to produce manganese peroxidase. The molecular weight of manganese peroxidase was determined as 46 kDa after Biogel P-100 gel filtration column chromatography purification. Maximum tetracycline degradation was observed with the manganese peroxidase from the strain Bacillus velezensis Al-Dhabi 140 and the optimum degradation process was studied. Optimization revealed the maximum removal efficacy was obtained as 87 mg/L at initial tetracycline concentration 143.75 mg/L, pH 6.94 and 8.04% inoculum. Consequently, fibrous bed reactor containing the culture of B. velezensis Al-Dhabi 140 in fibrous matrix was formed to transform tetracycline in synthetic wastewater. The transformed product of tetracycline from the fibrous bed reactor was evident by the activity of ligninolytic enzymes produced by B. velezensis Al-Dhabi 140 in reactor. The decreased level of antibacterial potency was obtained after 10 days. The zone of inhibition was 24 ± 1 mm after 1 day and it decreased as 9 ± 1 mm after 10 days. Based on the findings, fibrous bed B. velezensis Al-Dhabi 140 could be an efficient strain for tetracycline removal from artificial wastewater, even from natural wastewater.

Applicability of TiO2(B) nanosheets@hydrochar composites for adsorption of tetracycline (TC) from contaminated water

We test the feasibility of TiO₂(B)@carbon composites as adsorbents, derived from wheat straws, for tetracycline (TC) adsorption from aqueous solutions. Hydrochar (HC), biochar (BC), and hydrochar-derived pyrolysis char (HDPC) are synthesized hydrothermally from the waste and then functionalized with TiO₂(B), named as 'Composite-1', 'Composite-2', and 'Composite-3', respectively. A higher loading of TiO₂(B) into the HC was also synthesized for comparison, named as 'Composite-4'. To compare their physico-chemical changes before and after surface modification, the composites are characterized using FESEM-EDS, XRD, BET, FRTEM, and FTIR. The effects of H₂O₂ addition on TC removal are investigated. Adsorption kinetics and isotherms of TC removal are studied, while TC adsorption mechanisms are elaborated. We found that the Composite-4 has the highest TC removal (93%) at pH 7, 1 g/L of dose, and 4 h of reaction time at 50 mg/L of TC after adding H₂O₂ (10 mM). The TC adsorption capacities of the Composite-1 and Composite-4 are 40.65 and 49.26 mg/g, respectively. The TC removal by the Composite-1 follows the pseudo-second order. Overall, this suggests that converting the wheat straw into HC and then functionalizing its surface with TiO₂(B) as a composite has added values to the waste as an adsorbent for wastewater treatment.

Sorption of pharmaceuticals and personal care products on soil and soil components: Influencing factors and mechanisms

The sorption of pharmaceuticals and personal care products (PPCPs) on soil and soil components makes an important contribution to the fate, migration and bioavailability of PPCPs. Previous reviews have mostly focused on the sorption of PPCPs on single soil components (e.g., minerals and soil organic matter). However, the sorption of PPCPs within the whole soil system has not been systematically analyzed. This paper reviews the recent progress on PPCP sorption on soil and soil components. We have evaluated the sorption of a wide range of PPCPs in research fields that are usually considered in isolation (e.g., humic acids (HAs), montmorillonite, kaolinite, and goethite), and established a bridge between PPCPs and sorbent. The sorption mechanisms of PPCPs, e.g., cation exchange, surface complexation, electrostatic interaction and hydrogen bonding, are discussed and critically evaluated. We also assessed the influence of environmental factors (pH, ionic strength, organic matter and temperature) on sorption. This review summarizes the knowledge of PPCPs sorption on soil gained in recent years, which can provide new strategies for solving the problem of antibiotic pollution.

Insights into the mutual promotion effect of graphene oxide nanoparticles and tetracycline on their transport in saturated porous media

In this study, batch and column tests were performed to investigate the co-transport of graphene oxide (GO) nanoparticles and tetracycline in saturated porous media under various solution chemistry conditions. Research indicated that GO and tetracycline had mutual promotion effect on their transport in the porous media under all the tested conditions, which was ascribed to the high adsorption capacity of tetracycline onto GO and the increased electrostatic repulsion as well as their competition for deposition sites on sand surfaces. Interestingly, the mutually promoting function of GO and tetracycline under acidic conditions was greater than that under alkaline conditions, the dominant mechanism was that the increased solution pH decreased the sorption of tetracycline onto GO and weakened the deposition site competition. Furthermore, the mutually promoting effect of GO and tetracycline was Na⁺ or Ca²⁺ concentration-dependent. Specially, increased Ca²⁺ concentration weakened the promoting effect of GO on tetracycline transport but magnified the promoting effect of tetracycline on GO transport. This is because higher Ca²⁺ concentration could cause a decrease in the adsorption of tetracycline on GO and facilitate more tetracycline molecules to occupy the deposition sites on sand surfaces. Additionally, sodium dodecyl sulfate had enhancement effect on co-transport of GO and tetracycline. Findings from this study clearly indicated that antibiotics and carbon based nanomaterials may transport together under various solution chemistry conditions, and consequently affect their fates in aquatic environments.

A novel graphene oxide decorated with halloysite nanotubes (HNTs/GO) composite used for the removal of levofloxacin and ciprofloxacin in a wide pH range

A novel HNTs/GO composite used for the removal of levofloxacin and ciprofloxacin in a wide pH range.

Application of graphene-based materials for removal of tetracyclines using adsorption and photocatalytic-degradation: A review

Tetracyclines are extensively used to treat human and animal infectious diseases due to its effective antimicrobial activities. About 70-90% of its parent materials are released into the environment through urine and feces, implying they are the most frequently detected antibiotics in the environment with high ecological risks. Adsorption and photocatalysis have been promising techniques for the removal of tetracyclines due to effectiveness and efficiency. Graphene-based materials provide promising platforms for adsorptive and photocatalytic removal of tetracyclines from aqueous environment owning to distinctive remarkable physicochemical, optical, and electrical characteristics. Herein, we intensively reviewed the available literatures in order to provide comprehensive insight about the applications and mechanisms of graphene-based materials for removal of tetracyclines via adsorption and phototocatalysis. The synthesis methods of graphene-based materials, the tetracycline adsorption and photocatalytic-degradation conditions, and removal mechanisms have been extensively discussed. Finally concluding remarks and future perspectives have been deduced and recommended to stimulate further researches in the subject. The review study can be used as theoretical guideline for further researchers to improve the current approaches of material synthesis and application towards tetracyclines removal.

Modeling of chromium (VI) removal from aqueous solution using modified green-Graphene: RSM-CCD approach, optimization, isotherm, and kinetic studies

BACKGROUND

The aim of this study was to investigate the removal of Cr (VI) using Green-Graphene Nanosheets (GGN) synthesized from rice straw.

METHODS

Synthesis of the GGN was optimized using response surface methodology and central composite design (CCD). The effect of two independent variables including KOH-to-raw rice ash (KOH/RRA) ratio and temperature on the specific surface area of the GGN was determined. To have better removal of Cr (VI), GGN was modified using the grafting amine group method. In the Cr (VI) removal process, the effects of four independent variables including initial Cr (VI) concentration, adsorbent dosage, contact time, and initial solution pH were studied.

RESULTS

The results of this study showed that the optimum values of the KOH/RRA ratio and temperature for the preparation of GGN were 10.85 and 749.61 °C, respectively. The maximum amount of SSA obtained at optimum conditions for GGN was 551.14 ± 3.83 m 2 /g. The optimum conditions for Cr (VI) removal were 48.35 mg/L, 1.46 g/L, 44.30 min, and 6.87 for Cr (VI) concentration, adsorbent dosage, contact time, and pH, respectively. Based on variance analysis, the adsorbent dose was the most sensitive factor for Cr (VI) removal. Langmuir isotherm (R2 = 0.991) and Pseudo-second-order kinetic models (R2 = 0.999) were the best fit for the study results and the Q max was 138.89 mg/g.

CONCLUSIONS

It can be concluded that the predicted conditions from the GGN synthesis model and the optimum conditions from the Cr (VI) removal model both agreed with the experimental findings.

Facile, one-pot biosynthesis and characterization of iron, copper and silver nanoparticles using Syzygium cumini leaf extract: As an effective antimicrobial and aflatoxin B1 adsorption agents

In this study, a facile, ecological and economical green method is described for the fabrication of iron (Fe), copper (Cu) and silver (Ag) nanoparticles (NPs) from the extract of Syzygium cumini leaves. The obtained metal NPs were categorized using UV/Vis, SEM, TEM, FTIR and EDX-ray spectroscopy techniques. The Fe-, Cu- and Ag-NPs were crystalline, spherical and size ranged from 40−52, 28−35 and 11−19 nm, respectively. The Ag-NPs showed excellent antimicrobial activities against methicillin- and vancomycin-resistance Staphylococcus aureus bacterial strains and Aspergillus flavus and A. parasiticus fungal species. Furthermore, the aflatoxins (AFs) production was also significantly inhibited when compared with the Fe- and Cu-NPs. In contrast, the adsorption results of NPs with aflatoxin B₁ (AFB₁) were observed as following order Fe->Cu->Ag-NPs. The Langmuir isotherm model well described the equilibrium data by the sorption capacity of Fe-NPs (105.3 ng mg^-1), Cu-NPs (88.5 ng mg^-1) and Ag-NPs (81.7 ng mg^-1). The adsorption was found feasible, endothermic and follow the pseudo-second order kinetic model as revealed by the thermodynamic and kinetic studies. The present findings suggests that the green synthesis of metal NPs is a simple, sustainable, non-toxic, economical and energy-effective as compared to the others conventional approaches. In addition, synthesized metal NPs might be a promising AFs adsorbent for the detoxification of AFB₁ in human and animal food/feed.

Effects of heteroaggregation with metal oxides and clays on tetracycline adsorption by graphene oxide

Multiple nanoparticles (NPs) often coexist in water with contaminants, which inevitably affect the fate and transport of coexisted contaminants and other types of nanoparticles in actual water. This research was devoted to examine the adsorption of tetracycline (TC) on graphene oxide (GO) in the presence of different amounts of model engineered and natural NPs (m-NPs), including metal oxides (ZnO and Fe₂O₃), clays (kaolin and montmorillonite). The experimental results proved that the existence of m-NPs greatly enhanced the TC adsorption onto GO except for that at Fe₂O₃/GO = 10:1 and lengthened the adsorption equilibrium time. The enhanced adsorption amount of TC with increasing m-NPs/GO ratio was primarily due to the adsorption of TC onto m-NPs. In contrast, the slightly inhibitory effects by 10:1 Fe₂O₃/GO could be attributed to the blockage effect on GO surface by a small amount of Fe₂O₃. Compared with five m-NPs/adsorbents, m-NPs/GO had the greatest promoting efficiency on TC removal. Moreover, the heteroaggregation of GO with different m-NPs was studied in aqueous phase by microscopic, spectroscopic, and computational methods. Analysis showed that the electrostatic attraction between negatively charged GO and positively charged ZnO were likely to first heteroaggregate in binary systems of GO and ZnO, while GO were prone to homoaggregate owing to electrostatic repulsion with the same negatively charged montmorillonite (or kaolin). Besides, Fe₂O₃ tended to first homoaggregate and then heteroaggregate with GO. In summary, this report elucidated complex interactions between GO and m-NPs, which was crucial to fundamentally understand towards a predictive framework for describing the fate and migration of GO and m-NPs in actual water.

Molecular Interpretation of Pharmaceuticals’ Adsorption on Carbon Nanomaterials: Theory Meets Experiments

The ability of carbon-based nanomaterials (CNM) to interact with a variety of pharmaceutical drugs can be exploited in many applications. In particular, they have been studied both as carriers for in vivo drug delivery and as sorbents for the treatment of water polluted by pharmaceuticals. In recent years, the large number of experimental studies was also assisted by computational work as a tool to provide understanding at molecular level of structural and thermodynamic aspects of adsorption processes. Quantum mechanical methods, especially based on density functional theory (DFT) and classical molecular dynamics (MD) simulations were mainly applied to study adsorption/release of various drugs. This review aims to compare results obtained by theory and experiments, focusing on the adsorption of three classes of compounds: (i) simple organic model molecules; (ii) antimicrobials; (iii) cytostatics. Generally, a good agreement between experimental data (e.g. energies of adsorption, spectroscopic properties, adsorption isotherms, type of interactions, emerged from this review) and theoretical results can be reached, provided that a selection of the correct level of theory is performed. Computational studies are shown to be a valuable tool for investigating such systems and ultimately provide useful insights to guide CNMs materials development and design.

The effective adsorption of tetracycline onto zirconia nanoparticles synthesized by novel microbial green technology

Pseudomonas aeruginosa bacteria have been used in this study for zirconia nanoparticles synthesis through green technology for adsorption driven bioremediation of tetracycline from wastewater. The characterization of synthesized nano zirconia has been performed by employing dynamic light scattering, field emission-transmission electron microscopy, energy dispersive X-ray, X-ray diffraction, fourier transform infrared spectroscopy, and point of zero charge analysis. The zirconia nanoparticles have shown average particle size ~15 nm, monoclinic and tetragonal crystal structure with 6.41 nm of crystallite size, the presence of elemental zirconium and oxygen, and the occurrence of functional groups like O-Zr-OH, Zr-O-Zr and Zr-O bonds. The zirconia nanoparticles mediated adsorption of tetracycline has been found to be effective at solution pH 6.0 and in a very less contact time 15 min. Strong electrostatic interaction between zwitterionic form of tetracycline and protonated surface of zirconia nanoparticles is the governing adsorption mechanism in this study. The kinetic study has been performed on the basis of the tetracycline adsorption process revealing that the adsorption phenomenon follows pseudo-second order kinetic, further suggesting chemisorption of tetracycline over zirconia nanoparticles. The Langmuir isotherm model has been found to be the best fitted model among the all isotherm models indicating the involvement of monolayer uptake of tetracycline on the surface of zirconia nanoparticles. Moreover, the maximum tetracycline adsorption capacity of zirconia nanoparticles calculated by the Langmuir isotherm model is close to 526.32 mg/g. This finding is quite reasonable to accept that zirconia nanoparticle may be used as an alternative adsorbent to mitigate the tetracycline contamination in wastewater.

Removal of tetracycline from an aqueous solution using manganese dioxide modified biochar derived from Chinese herbal medicine residues

Biochar (BC) derived from Chinese herbal medicine residues has been investigated for its performance as a potential adsorbent in tetracycline (TC) removal. In the present study, a chemical co-precipitation method was carried out to prepare manganese dioxide modified biochar (Mn-BC) to increase its sorption capacity. The properties of the modified biochar were characterized for further enhancing TC removal from an aqueous solution. Mn-BC was successfully synthesized and resulted in a much higher specific surface area, total pore volume and pore diameter. The sorption kinetics of TC on Mn-BC was described by the pseudo-second-order model. The sorption data of Mn-BC were fitted by Langmuir and Freundlich models. The study findings revealed a maximum adsorption capacity of Mn-BC (1:10) to TC was up to 131.49 mg/g. The adsorption process was endothermic and spontaneous. The degradation of TC was further enhanced by MnO₂ acting as an oxidizer on Mn-BC. Overall, the modified biochar derived from Chinese herbal medicine residues is a superior alternative for the removal of TC from an aqueous solution.

Application and biomolecular study of functionalized folic acid-dendrimer nanoparticles in drug delivery

We determined the loading efficacy of folic acid - PAMAM - G3 and folic acid - PAMAM - G4 nanoparticles with doxorubicin (Dox), tamoxifen (Tam) and tetracycline (Tet) in aqueous solution at pH 7.2. Thermodynamic parameters ΔH⁰ -16 to -4 (kJ mol^-1), ΔS⁰ 31 to -0.3 (J mol^-1K^-1) and ΔG⁰ -14 to -11 (kJ mol^-1) showed drug folic acid-PAMAM bindings are via ionic, H-bonding and van der Waals interactions. As acid - PAMAM size increased the stability and loading efficacy of drug-polymer conjugates were increased. The order of stability for drug-nanoparticles was doxorubicin > tetracycline > tamoxifen. TEM analysis showed major polymer morphological changes, upon drug encapsulation. Folic acid-PAMAM conjugates are effective drug delivery tools in vitro. Communicated by Ramaswamy H. Sarma.

Adsorptive removal of antibiotics from water over natural and modified adsorbents

Various adsorbents including agricultural waste-based adsorbents, nanomaterials and layered double hydroxides have been reviewed for removal of antibiotics from water due to their unique properties. The adsorption mechanism is governed mostly by the affinity of a pollutant to adsorbent materials. However, the main adsorption mechanisms defined in this study for removal of antibiotics are the electrostatic attraction, π-π interaction and hydrogen bonding. The study highlighted the contribution of modification in the adsorption capacity of antibiotics. Some of the most important adsorbents discussed in this review are graphene-based adsorbents, binary layered double hydroxides and magnetic nanoparticles as well as the antibiotics sulfamethoxazole, tetracycline and metronidazole. The key factors for the selection of the suitable materials are the structure, characteristics and other physicochemical parameters such as pH and temperature. However, the most crucial factor is the adsorption capacity. Some of the adsorption kinetics models and isotherms for antibiotic sorption are also highlighted in this study. In addition, the review summarizes the future prospects and recent challenges faced with the adsorption techniques for removal of antibiotics from wastewater. This review will help readers understand the current trend in the adsorptive removal of antibiotics from water.

Nanohybrid Scaffold of Chitosan and Functionalized Graphene Oxide for Controlled Drug Delivery and Bone Regeneration

Nanohybrid scaffolds of chitosan have been designed for controlled drug delivery and bone regeneration. Sulfonated graphene oxide has been used to develop the nanohybrids. Nanohybrid scaffolds show highly hydrophilic character and greater mechanical strength as compared to pure chitosan. Nanohybrid scaffolds show an interconnected uniform porous network structure exhibiting sustained release kinetics of the antibacterial drug, tetracycline hydrochloride. Nanohybrids are found to be highly biocompatible in nature and are able to support and proliferate MG63 osteoblast cells and thereby induce bone tissue regeneration. The in-vivo bone healing study shows that the developed nanohybrid scaffolds have the potential to regenerate the bone faster without any side effects as compared to pure scaffolds. Hence, the developed nanohybrid scaffold has good potential as a controlled drug delivery vehicle and in bone tissue engineering for faster healing.

Graphene and graphene-based nanocomposites used for antibiotics removal in water treatment: A review

Due to their extensive application in human and veterinary medicine, antibiotics have been found worldwide and studied as new pollutants in the aquatic environment. In order to remove such pollutants, adsorption and photocatalysis have attracted tremendous attention because of their great potential in antibiotics removal from aqueous solutions. Graphene, as a novel two-dimensional nanomaterial, possesses unique structure and physicochemical properties, which can be used to efficiently adsorb and photodegrade antibiotics. This review provides an overview of the adsorptive and catalytic properties of graphene, and recent advances in adsorption and photodegradation of antibiotics by graphene and its derivatives. The factors that affect the adsorption and photodegradation of antibiotics are reviewed and discussed. Furthermore, the underlying mechanisms of adsorption and photodegradation are summarized and analyzed. Meanwhile, statistical analysis is conducted based on the number of papers and the maximum adsorption and photodegradation ability on various antibiotics removal. Finally, some unsolved problems together with major challenges that exist in the fabrication and application of graphene-based nanocomposites and the development for antibiotics removal is also proposed. This work provides theoretical guidance for subsequent research in the field of adsorption and photocatalytic removal of antibiotics from aqueous solution, especially on influence factors and mechanisms aspects.

Graphene oxide immobilized surfaces facilitate the sustained release of doxycycline for the prevention of implant related infection

Preventing implant-associated infection, which can lead to implant failure and increased medical costs, is one of the biggest challenges in the orthopaedic surgeons. Therefore, the development of stable and highly effective surface modifications to increase the antimicrobial properties of implants is required. In this study, graphene oxide (GO-)-immobilized titanium dioxide (TiO₂) was developed to efficiently carry and release antimicrobial drugs. Firstly, tyramine-conjugated GO (GOTA) was synthesized and immobilized onto the surfaces of TiO₂ through tyrosinase (Tyr)-catalyzed oxidative reaction (GOTA/TiO₂). Doxycycline hyclate (Dox) was then loaded onto GOTA/TiO₂ via non-covalent interactions between GO and Dox (Dox/GOTA/TiO₂), including electrostatic interaction, π-π stacking, hydrophobic interaction, and hydrogen bonds. The amount of loaded drug was able to be controlled, reaching a maximum of 36 μg/cm². in vitro experiments revealed that the sustained release of Dox from the TiO₂ surfaces continued for over 30 days. Compared with bare TiO₂ and GOTA/TiO₂, Dox/GOTA/TiO₂ exhibited superior antibacterial activity against both gram-negative Escherichia coli and gram-positive Staphylococcus aureus bacteria, without affecting the viability of human dermal fibroblasts. The obtained results indicated that GO-immobilized TiO₂ is an effective carrier for antimicrobial drug delivery to reduce implant-associated infection through the synergistic antimicrobial effect of GO and the prescribed drugs.

Combined Minimum-Run Resolution IV and Central Composite Design for Optimized Removal of the Tetracycline Drug Over Metal⁻Organic Framework-Templated Porous Carbon

In this study, a minimum-run resolution IV and central composite design have been developed to optimize tetracycline removal efficiency over mesoporous carbon derived from the metal-organic framework MIL-53 (Fe) as a self-sacrificial template. Firstly, minimum-run resolution IV, powered by the Design-Expert program, was used as an efficient and reliable screening study for investigating a set of seven factors, these were: tetracycline concentration (A: 5-15 mg/g), dose of mesoporous carbons (MPC) (B: 0.05-0.15 g/L), initial pH level (C: 2-10), contact time (D: 1-3 h), temperature (E: 20-40 °C), shaking speed (F: 150-250 rpm), and Na+ ionic strength (G: 10-90 mM) at both low (-1) and high (+1) levels, for investigation of the data ranges. The 20-trial model was analyzed and assessed by Analysis of Variance (ANOVA) data, and diagnostic plots (e.g., the Pareto chart, and half-normal and normal probability plots). Based on minimum-run resolution IV, three factors, including tetracycline concentration (A), dose of MPC (B), and initial pH (C), were selected to carry out the optimization study using a central composite design. The proposed quadratic model was found to be statistically significant at the 95% confidence level due to a low P-value (<0.05), high R2 (0.9078), and the AP ratio (11.4), along with an abundance of diagnostic plots (3D response surfaces, Cook's distance, Box-Cox, DFFITS, Leverage versus run, residuals versus runs, and actual versus predicted). Under response surface methodology-optimized conditions (e.g., tetracycline concentration of 1.9 mg/g, MPC dose of 0.15 g/L, and pH level of 3.9), the highest tetracycline removal efficiency via confirmation tests reached up to 98.0%-99.7%. Also, kinetic intraparticle diffusion and isotherm models were systematically studied to interpret how tetracycline molecules were absorbed on an MPC structure. In particular, the adsorption mechanisms including "electrostatic attraction" and "π-π interaction" were proposed.

Removal of antibiotics from aqueous solutions by nanoparticles: a systematic review and meta-analysis

Antibiotics, as one of the emerging pollutants, are non-biodegradable compounds and long-term exposure to them may affect endocrine, hormonal, and genetic systems of human beings, representing a potential risk for both the environment and human health. The presence of antibiotics in surface waters and drinking water causes a global health concern. Many researches have stated that conventional methods used for wastewater treatment cannot fully remove antibiotic residues, and they may be detected in receiving waters. It is reported that nanoparticles could remove these compounds even at low concentration and under varied conditions of pH. The current study aimed to review the most relevant publications reporting the use of different nanoparticles to remove antibiotics from aqueous solutions. Moreover, meta-analysis was conducted on the results of some articles. Results of meta-analysis proved that different nanoparticles could remove antibiotics with an acceptable efficiency of 61%. Finally, this review revealed that nanoparticles are promising and efficient materials for degradation and removal of antibiotics from water and wastewater solutions. Furthermore, future perspectives of the new generation nanostructure adsorbents were discussed in this study.