Removal of organic and inorganic effluents from wastewater by using degradation and adsorption properties of transition metal-doped nickel ferrite

Removal of water pollutants (methylene blue dye and heavy metals) was achieved by zinc/manganese-doped nickel ferrites (Ni1 - xMxFe2O4, where x = 0.00, 0.025, 0.10). Degradation of dye was achieved under natural solar light illumination. Degradation studies of dye were conducted under different parameters such as contact time-80 min, dye's concentration-5 mg/L, pH-7, and dosage of ferrites-15 mg. The adsorption of dye was studied using non-linear kinetics models (pseudo-first-order and pseudo-second-order) and isotherm models (Langmuir and Freundlich). The adsorption of dye followed pseudo-first-order kinetics (R2 = 0.99377) than second-order kinetics (R2 = 0.98063) and Langmuir isotherm model (R2 = 0.96095) than Freundlich model (R2 = 0.95962) with maximum adsorption efficiency of 29.62 mg/g. Doping of nickel ferrites caused an increase in the removal percentage of methylene blue dye (80 to 90%) and inorganic effluents (75 to 95% for lead and 47 to 82% for cadmium). In addition to this, band gap energy (2.43 to 3.26 eV) (UV-Vis spectroscopy), pore radius (65.2 to 74.8 A°), and specific surface area (16.45 to 27.95 m2/g) (BET analysis) were also increased. Generally, the results of the study revealed that synthesized nanoparticles can act as potential candidate for the removal of effluents from wastewater under optimum parameters along with recyclability, reusability, and separation under the influence of a magnetic field.

Impact of silver substitution on the structural, magnetic, optical, and antibacterial properties of cobalt ferrite

Silver-doped Cobalt Ferrite nanoparticles AgxCo1-xFe2O4 with concentrations (x = 0, 0.05, 0.1, 0.15) have been prepared using a hydrothermal technique. The XRD pattern confirms the formation of the spinel phase of CoFe2O4 and the presence of Ag ions in the spinel structure. The spinel phase AgxCo1-xFe2O4 nanoparticles are confirmed by FTIR analysis by the major bands formed at 874 and 651 cm-1, which represent the tetrahedral and octahedral sites. The analysis of optical properties reveals an increase in band gap energy with increasing concentration of the dopant. The energy band gap values depicted for prepared nanoparticles with concentrations x = 0, 0.05, 0.1, 0.15 are 3.58 eV, 3.08 eV, 2.93 eV, and 2.84 eV respectively. Replacement of the Co2+ ion with the nonmagnetic Ag2+ ion causes a change in saturation magnetization, with Ms values of 48.36, 29.06, 40.69, and 45.85 emu/g being recorded. The CoFe2O4 and Ag2+ CoFe2O4 nanoparticles were found to be effective against the Acinetobacter Lwoffii and Moraxella species, with a high inhibition zone value of x = 0.15 and 8 × 8 cm against bacteria. It is suggested that, by the above results, the synthesized material is suitable for memory storage devices and antibacterial activity.

BaTiO3/NixZn1−xFe2O4 (x = 0, 0.5, 1) Composites Synthesized by Thermal Decomposition: Magnetic, Dielectric and Ferroelectric Properties

To investigate the influence of spinel structure and sintering temperature on the functional properties of BaTiO3/NixZn1−xFe2O4 (x = 0, 0.5, 1), NiFe2O4, ZnFe2O4, and Ni0.5Zn0.5Fe2O4 were in situ prepared by thermal decomposition onto BaTiO3 surface from acetylacetonate precursors. As-prepared powders were additionally sintered at 1150 °C and 1300 °C. X-ray powder diffraction (XRPD) and scanning electron microscopy (SEM) coupled with electron dispersive spectroscopy (EDS) were used for the detailed examination of phase composition and morphology. The magnetic, dielectric, and ferroelectric properties were investigated. The optimal phase composition in the BaTiO3/NiFe2O4 composite, sintered at 1150 °C, resulted in a wide frequency range stability. Additionally, particular phase composition indicates favorable properties such as low conductivity and ideal-like hysteresis loop behavior. The favorable properties of BaTiO3/NiFe2O4 make this particular composite an ideal material choice for further studies on applications of multi-ferroic devices.

Green synthesis of iron nanoparticles and photocatalytic activity evaluation for the degradation of methylene blue dye

The present study focuses on iron nanoparticles (Fe NPs) biosynthesis, characterization and photocatalytic activity (PCA) appraisal for methylene blue dye degradation. A green rapid biogenic synthesis route was employed for synthesis of Fe NPs using banana peel extract. The synthesized Fe NPs was characterized by XRD (X-ray diffraction), SEM (scanning electron microscopy) and EDX (energy dispersive X-ray) techniques. These analysis confirmed the synthesis of zero valent Fe NPs with high crystallinity, purity and semi spherical in shape. The photocatalytic activity was assessed under ultra violet irradiation and under optimum conditions, 87% degradation of MB dye was obtained for 72 min of irradiation, which revealed promising catalytic efficiency of the Fe NPs. The result shows that photocatalytic activity of Fe NPs is promising and could possibly be used to treat dyes in industrial effluents and the use of green synthetic protocol is suggested due to its ecofriendly nature.

Kinetics of acid blue 40 dye degradation under solar light in the presence of CuO nanoparticles synthesized using Citrullus lanatus seeds extract

In view of eco-benign nature of green synthesis, in the present investigation, the CuO NPs are prepared using Citrullus lanatus seeds extract and photocatalytic degradation efficiency for Acid Blue 40 (AB-40) was evaluated. The CuO NPs were characterized by XRD (X-ray diffraction), SEM (scanning electron microscopy), EDX (energy dispersive X-ray), and FT-IR (Fourier transform infrared) techniques. The synthesized CuO NPs was in face centered monoclinic crystalline form with particle size in 40–60 nm range. The photocatalytic degradation potential of CuO NPs was assessed for acid blue 40 (AB-40) dye degradation and catalyst dose, concentration of dye, radiation exposure time and pH are considered for dye removal. The CuO NPs exhibited auspicious efficiency, an 84.89% dye removal was attained at optimal conditions and dye degradation followed BMG (Behnajady–Modirshahla–Ghanbery) kinetics model. Results revealed CuO NPs synthesized using C. lanatus seeds extract is photoactive catalyst and green route can be employed for CuO NPs fabrication for photocatalytic applications.

Biochar caged zirconium ferrite nanocomposites for the adsorptive removal of Reactive Blue 19 dye in a batch and column reactors and conditions optimizaton

Biochar caged zirconium ferrite (BC-ZrFe2O5) nanocomposites were fabricated and their adsorption capacity for Reactive Blue 19 (RB19) dye was evaluated in a fixed-bed column and batch sorption mode. The adsorption of dye onto BC-ZrFe2O5 NCs followed pseudo-second-order kinetics (R 2 = 0.998) and among isotherms, the experimental data was best fitted to Sips model as compared to Freundlich and Langmuir isotherms models. The influence of flow-rate (3–5 mL min−1), inlet RB19 dye concentration (20–100 mg L−1) and quantity of BC-ZrFe2O5 NCs (0.5–1.5 g) on fixed-bed sorption was elucidated by Box-Behnken experimental design. The saturation times (C t /C o  = 0.95) and breakthrough (C t /C o  = 0.05) were higher at lower flow-rates and higher dose of BC-ZrFe2O5 NCs. The saturation times decreased, but breakthrough was increased with the initial RB19 dye concentration. The treated volume was higher at low sorbent dose and influent concentration. Fractional bed utilization (FBU) increased with RB19 dye concentration and flow rates at low dose of BC-ZrFe2O5 NCs. Yan model was fitted best to breakthrough curves data as compared to Bohart-Adams and Thomas models. Results revealed that BC-ZrFe2O5 nanocomposite has promising adsorption efficiency and could be used for the adsorption of dyes from textile effluents.

Microstructural characterization and corrosion behaviour of ultrasound-assisted synthesis of Ni–xCo–yTiO2 nanocomposites in alkaline environments

Electroplated protective thin film is highly promising materials for advanced applications such as high corrosion resistance and energy conversion and storage. This work is to investigate the effect of Co content and TiO2 on the corrosion resistance of Ni–xCo–yTiO2 nanocomposites in alkaline media. The nanocrystalline Ni–xCo–yTiO2 composites were electroplated using the sulfate-gluconate bath containing the suspended TiO2 nanograins under ultrasound waves and mechanical stirring. The microstructure and corrosion behavior of the electroplated Ni–xCo–yTiO2 nanocomposites have been investigated via X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques. The XRD pattern of the electroplated Ni–Co matrices with 1–75% of cobalt arranged in face-centered cubic (FCC) system, while the electroplated Ni–Co matrices of further Co% more than 76% converted to hexagonal closed-package (HCP) crystal system. The surface of the Ni–xCo–yTiO2 nanocomposites after immersion in 1.0 M KOH electrolytes was investigated via SEM, atomic force microscopy and EDX. The results displayed that the rate of corrosion of the different composites decreased by combining Ni, Co and the inclusion of TiO2. The improved corrosion resistance of Ni–47Co–3.77TiO2 composites is due to the formation of Ni/Co oxy/hydroxide layer and rebelling effect of OH− by TiO2 sites, which reduces the attacking effect of OH−, O2, and H2O, and notably retards the overall corrosion processes.

State-of-art of silver and gold nanoparticles synthesis routes, characterization and applications: a review

To date, the noble metal-based nanoparticles have been used in every field of life. The Au and Ag nanoparticles (NPs) have been fabricated employing different techniques to tune the properties. In this study, the methodologies developed and adopted for the fabrication of Au and Ag have been discussed, which include physical, chemical and biological routes. The Au and Ag characteristics (morphology, size, shape) along with advantages and disadvantages are discussed. The Au and Ag NPs catalytic and biomedical applications are discussed. For the Ag and Au NPs characterization, SEM (scanning electron microscope), TEM (transmission electron microscope), FTIR (Fourier transform infra-red spectroscopy), XRD (X-rays diffraction) and DLS (dynamic light scattering) techniques are employed. The properties of Au and Ag NPs found dependent to synthesis approach, i.e., the size, shape and morphologies, which showed a promising Catalytic, drug delivery and antimicrobial agent applications. The review is a comprehensive study for the comparison of Au and Ag NPs synthesis, properties and applications in different fields.

Hydrothermal synthesis, characterization and photocatalytic activity of Mg doped MoS2

In this research work nanoparticles of Mg (0, 1, 2 and 3%) doped MoS2 are prepared by Hydrothermal method at 200 °C for 9 h. Scanning Electron Microscope (SEM) for surface morphology, Fourier Transform Infrared Spectroscopy (FTIR) for structural and chemical bonding and UV-visible spectroscopy for optical properties are used. SEM showed that sheet-like structure has changed into stone-like shaped when Mg has doped into MoS2. From FTIR, Mo–O, Mo=S, and H–O bond peaks are becoming dim and new chemical bonds S=O, Mo=O, Mg–O, CH and OH are forming with the increase of Mg doping. UV-visible spectroscopy showed that MoS2 has an indirect bandgap 2.21 eV. Band gap decreased from 1.84 to 1.82 eV when the Mg doping was increased from 1 to 2%, respectively. As Mg concentration was increased i.e. 3% then band gap increased to 1.88 eV. Photocatalytic activity (PCA) of undoped and Mg doped MoS2 is appraised by degrading rhodamine blue (RhB) and methylene blue (MB) dyes. The results showed that PCA (in presence of visible light) Mg doped MoS2 is greater than pure MoS2 which significantly increased the photocatalytic properties.

Highly photosensitized Mg4 Si6O15 (OH)2·6H2O@guar gum nanofibers for the removal of methylene blue under solar light irradiation

In the present investigation, photosensitized nanofibers (NFs) based on guar gum (GG)/poly(vinyl alcohol) (PVA)/Mg4Si6O15(OH)2·6H2O (SP) (modified by 1, 4-diamminobutane [DAB]) was fabricated by electrospinning approach and same was used for the degradation of dye under solar light irradiation. For electrospinning of NFs, the acceleration voltage, nozzle flow rate and collector distance levels of 19,000 KV, 0.5 mL/h and 3 cm were optimum conditions along with 7% (w/v) blend of GG/PVA (1.4:5.6 wt/wt) and 0.01 g modified Mg4Si6O15(OH)2·6H2O. The exfoliation, intercalation and clay organophilization in GG/PVA/Mg4Si6O15(OH)2·6H2O (GG/PVA/SP) NFs were examined by FTIR analysis. The photocatalytic activity (PCA) of NF was studied under the solar light irradiation for methylene blue (MB) dye degradation. The photosensitized GG/PVA/SP2 (G3) showed promising PCA under visible light and G3 furnished higher degradation of MB dye (99.1%) within 10 min of irradiation. Results revealed that GG/PVA/SP based NFs are highly active under solar light, which can be applied for the treatment of wastewater.

Kinetics and Equilibrium of Radioactive Metal Adsorption onto Sugarcane Bagasse Waste: Comparison of Batch and Column Adsorption Modes

Sugarcane bagasse waste biomass (SBWB) efficacy for the adsorption of Zr(IV) was investigated in batch and column modes. The process variables i.e. pH 1–4 (A), adsorbent dosage 0.0–0.3 g (B), and Zr(IV) ions initial concentration 25–200 mg/L (C) were studied. The experiments were run under central composite design (CCD) and data was analysed by response surface methodology (RSM) methodology. The factor A, B, C, AB interaction and square factor A2, C2 affected the Zr(IV) ions adsorption onto SBWB. The quadratic model fitted well to the adsorption data with high R2 values. The effect of bed height, flow rate and Zr(IV) ions initial concentration was also studied for column mode adsorption and efficiency was evaluated by breakthrough curves as well as Bed Depth Service and Thomas models. Bed height and Zr(IV) ions initial concentration enhanced the adsorption of capacity of Zr(IV) ions, whereas flow rate reduced the column efficiency.

Synthesis and characterization of magnetically separable La1−x Bi x Cr1−y Fe y O3 and photocatalytic activity evaluation under visible light

A series of Bi and Fe doped La1−x Bi x Cr1−y Fe y O3 (x = 0.00–0.10 and y = 0.02–0.12) perovskites were fabricated through a facile microemulsion method and were characterized by XRD, DC electrical-resistivity, dielectric, VSM, and UV–Visible measurements. Orthorhombic phase of synthesized substituted chromite nanocrystallite was confirmed by powdered XRD analysis with crystallite size in 47.8–32.9 nm range. DC electrical resistivity was observed to increase from 1.70–39.99 × 108 Ω-cm. Dielectric parameters analyzed in frequency range of 20 kHz–20 MHz were decreased, while magnetic parameters were observed to increase with the increase in dopant (Bi+3 and Fe+3) concentration. Whereas coercivity values was low (narrow hysteresis loop), which indicate the soft ferromagnetic of the prepared material materials which are quite useful to employ in storage devices and electronics. Moreover, La1−x Bi x Cr1−y Fe y O3 degraded 90.80% Rhodamine B dye under visible light irradiation within 55 min. The increase in electrical resistivity, while decrease in dielectric parameters was also observed with increase in dopant concentration, ferromagnetic nature and excellent photocatalytic properties make this material suitable for high frequency energy devices, microwave appliances as well as an excellent magnetically separable photocatalyst for the purification of contaminated wastewater.

ZnO, CuO and Fe2O3 green synthesis for the adsorptive removal of direct golden yellow dye adsorption: kinetics, equilibrium and thermodynamics studies

In the present investigation, ZnO, CuO and Fe2O3 were prepared via green route and utilized for the sequestration of DGY (Direct Golden Yellow) dye. Affecting variables i.e., temperature, contact time, adsorbent dose and pH were optimized for maximum sequestration of dye from aqueous medium. The pH 2, adsorbent dose 0.1 g/50 mL dye solution, temperature 30 °C and 50 mg/L dye initial concentration were best levels for efficient dye adsorption and equilibrium was attained in 30 min reaction time. The dye sequestration on to ZnO, CuO and Fe2O3 was an exothermic process. Freundlich and Temkin adsorption isotherms explained well the dye adsorption onto nanoadsorbents and dye adsorption followed pseudo first order kinetic model. Effect of electrolytes and heavy metal ions was also investigated and both affected the adsorption process significantly. In the presences of surfactant/detergent, the removal of dye was reduced and 0.5 N NaOH efficiently desorbed the dye from nanoadsorbents. Findings depicted that the nanoadsorbents are effectual for the sequestration of DGY dye, which can be employed for the remediation of textile effluents.

Structural, electric and dielectric properties of perovskite based nanoparticles for energy applications

A nanocomposite electrode, obtained by combining two high performance perovskite materials, such as lanthanum strontium cobalt ferrite, La0.6Sr0.4Co0.2Fe0.8O3−δ (LSCF) and gadolinium doped ceria, Ce0.85Gd0.15O1.5 (GDC), were investigated as a promising cathode for moderate temperature solid oxide fuel cells (SOFCs). The synthesized material has good conductivity and catalytic performance. The purpose of this synthesis was to prepare a stable and highly performing nanocomposite cathode material. In this research work, LSCF and GDC were separately synthesized by co-precipitation and solid-state reaction method to gain a homogeneous perovskite phase. Varying concentrations of LSCF–GDC composite with GDC (10 wt.%, 20 wt.% and 30 wt.%) were synthesized followed by calcination at 600 °C to remove water content and to achieve an adequate porous structure for oxygen absorption and desorption. These fabricated LSCF, GDC, and the nanocomposite specimens were characterized for microstructure, particle size etc. via. X-ray diffraction method (XRD), scanning electron microscope (SEM) and the laser particle size analyzer. This procedural approach helps to expand new methods for generating bi-functional duel nano-sized perovskites with great performance and stability which can be utilized for advancement of renewable energy sectors especially for rechargeable fuel batteries.

Structural, electric and dielectric properties of perovskite based nanoparticles for energy applications

A nanocomposite electrode, obtained by combining two high performance perovskite materials, such as lanthanum strontium cobalt ferrite, La0.6Sr0.4Co0.2Fe0.8O3−δ (LSCF) and gadolinium doped ceria, Ce0.85Gd0.15O1.5 (GDC), were investigated as a promising cathode for moderate temperature solid oxide fuel cells (SOFCs). The synthesized material has good conductivity and catalytic performance. The purpose of this synthesis was to prepare a stable and highly performing nanocomposite cathode material. In this research work, LSCF and GDC were separately synthesized by co-precipitation and solid-state reaction method to gain a homogeneous perovskite phase. Varying concentrations of LSCF–GDC composite with GDC (10 wt.%, 20 wt.% and 30 wt.%) were synthesized followed by calcination at 600 °C to remove water content and to achieve an adequate porous structure for oxygen absorption and desorption. These fabricated LSCF, GDC, and the nanocomposite specimens were characterized for microstructure, particle size etc. via. X-ray diffraction method (XRD), scanning electron microscope (SEM) and the laser particle size analyzer. This procedural approach helps to expand new methods for generating bi-functional duel nano-sized perovskites with great performance and stability which can be utilized for advancement of renewable energy sectors especially for rechargeable fuel batteries.

Comprehensive facts on dynamic antimicrobial properties of polysaccharides and biomolecules-silver nanoparticle conjugate

Based on progress for the green synthesis of nanoparticle (NPs), the mushrooms have also been utilized extensively for the biogenic synthesis of NPs. In recent years, silver NPs have been fabricated using mushrooms. The antimicrobial drugs are efficient to control the infectious diseases, but due to widespread of drugs, microbes became resistant to drugs, which demands develop of new bioactive agents. The silver NPs have been recognized as efficient broad spectrum antimicrobial agents, which have been fabricated using polysaccharides from mushrooms as reducing and capping agent. This review focused on the comprehensive study that deals silver NPs polysaccharides from Pleurotus mushroom, their synthesis mechanism, action mechanism of silver NPs and their characterization using advanced techniques i.e., ultraviolet-visible (UV-Vis), dynamic light scattering, Fourier transformation infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), transmission electron microscopy (TEM) and XRD. The Pleurotus mushroom showed promising efficiency for the biogenic synthesis of polysaccharides‑silver NPS and as-prepared NPs showed excellent antimicrobial activity.

Metallurgical Processing Strategies for Metals Recovery from Industrial Slags

Slag produced as a byproduct in industrial processes, contains considerable metals contents, which need to be recovered to avoid environmental contamination. In present review, the types, applications, recovery of metals from slag and their hazardous effects have been discussed. Gravimetric, magnetic, floatation, pyrometallurgical and hydrometallurgical treatments are discussed for processing of charge chrome, steel, copper smelter, brass smelter, tin, incineration, ferrochrome and silico-manganese slags for the extraction of various metal ions (Mg, Cu, Zn, Pb, Cd, Ni, Co, Mn, Fe, As, Cr, Al, Nb, Ag, Au, Nb, Ta, Cu, Co, Ni, Fe, V, Cr). The possibility of biometallurgical processing of slags is also evaluated. Merits and demerits of extraction and purification techniques are highlighted with possible suggestions and possibility of integrated leaching techniques is also discussed.

Sol–Gel Synthesis of Mesoporous Silica–Iron Composite: Kinetics, Equilibrium and Thermodynamics Studies for the Adsorption of Turquoise-Blue X-GB Dye

Mesoporous silica (MPS) and MPS-Fe composite was prepared via sol–gel technique and characterized by BET, FTIR, XRD, SEM and pZc. The MPS and MPS-Fe adsorption efficiencies were evaluated for a cationic dye Turquoise-blue X-GB. The MPS-Fe composite showed pore size and BET values of 9.52 nm and 309 m2/g, respectively. XRD and SEM analysis revealed the amorphous nature and uniform distribution of spherical partciles with average particle size of 50 nm of MPS-Fe composite. The points of zero (pZc) charge found to be 2.3 and 6.3 for MPS and MPS-Fe, respectively. The MPS and MPS-Fe showed promising efficiency for the adsorption of Turquoise-blue X-GB as a function of medium pH, contact time, dye initial concentration and temperature. Among, Freundlich, Langmuir, Harkins–Jura, Temkin, Doubinin–Radushkevich isotherms, the Turquoise-blue X-GB followed Langmuir isothermal model with adsorption capacities of 83.34 mg/g and 74.07 mg/g for MPS and MPS-Fe composite, respectively. Among kinetics models, pseudo second order kinetic model fitted to the dye adsorption with R2 values of 0.998 and 0.988 for MPS and MPS-Fe composite, respectively. The negative values of enthalpy (ΔH) and free energy (ΔG) revealed exothermic and spontaneous adsorption of dye at room temperature. Results revealed that MPS and MPS-Fe composite have promising potential for Turquoise-blue X-GB dye adsorption and could possibly be extended for the adsorption of dyes from textile effluents.

Effect of Hydrothermal Reaction Time on Electrical, Structural and Magnetic Properties of Cobalt Ferrite

Cobalt ferrite was synthesized by hydrothermal route in order to investigate the effect of hydrothermal reaction time on structural, magnetic and dielectric properties. The synthesized cobalt ferrite was characterized by X-ray diffraction, Fourier transform infrared and Vibrating-Sample Magnetometer (VMS). XRD data analysis confirmed the formation of cubic inverse spinel ferrite for complete time series as the high intensity peak corresponds to cubic normal spinel structure. The ionic radii, cation distribution among tetrahedral and octahedral sites, lattice parameters, X-ray density, bond lengths were also investigated cobalt ferrite prepared at different hydrothermal reaction time. The crystallite size was found to be in the range of 11.79–32.78 nm. Tolerance factor was near unity that also confirms the formation of cubic ferrites. VSM studies revealed the magnetic nature of cobalt ferrite. The coercivity (1076.3Oe) was observed for a sample treated for 11 h. The squareness ratio was 0.56 that is close to 0.5 which shows uniaxial anisotropy in cobalt ferrite. Frequency dependent dielectric properties i.e. dielectric constant, AC conductivity, tangent loss and AC resistivity are calculated with the help of Impedance Analyzer. Intrinsic cation vibration of cubic spinel ferrites are confirmed from FTIR analysis in the range of 400–4000 cm−1. In view of enhanced properties, this technique could possibly be used for the synthesis of cobalt ferrite for different applications.