Synthesis and Application of LTA Zeolite for the Removal of Inorganic and Organic Hazardous Substances from Water: A Review

Industrialization and human activities have caused significant environmental challenges, with water pollution posing severe risks to human health. This underscores the urgent need for effective water treatment solutions. Zeolites, known for their high specific surface area and stability, have gained increasing attention as adsorbents for water treatment. Among zeolites, LTA varieties stand out due to their low Si/Al ratio, which enhances ion-exchange capacity, and their cost-effectiveness. This review focuses on the synthesis of low-silica LTA zeolites, particularly zeolite A, using natural materials and solid wastes without relying on organic-structure-directing agents (OSDAs). Common pretreatment processes for such synthesis are also highlighted. The review further explores the applications of LTA zeolites in water treatment, emphasizing their exceptional performance in adsorbing inorganic and organic pollutants. In particular, LTA zeolites are highly effective at removing inorganic cation pollutants through ion exchange. An updated ion-exchange selectivity order, based on previous studies, is provided to support these findings. Overall, this review aims to guide future research and development in water treatment technologies.

Biogenic engineered zinc oxide nanoparticle for sulfur black dye removal from contaminated wastewater: comparative optimization, simulation modeling, and isotherms

This research work aimed to isolate and culture the bacterium Bacillus paramycoides for biogenic fabrication of zinc oxide nanoparticles, specifically ZnO and ZnO-ME nanoparticles (nanoparticles fabricated from bacterial extracts only - ZnO, and from bacterial cell mass including extract - ZnO-ME). SEM investigation revealed the spherical-shaped NPs with 22.33 and 39 nm in size for ZnO and ZnO-ME, respectively. The Brunauer, Emmett, and Teller (BET) studies revealed mesoporous structure with pore diameters of 13.839 and 13.88 nm and surface area of 7.617 and 33.635 m2/gm for ZnO and ZnO-ME, respectively. Various parameters for the adsorption of sulfur black dye onto both ZnO and ZnO-ME were screened and optimized using Plackett-Burman Design (PBD), Full Factorial Design (FFD) and Central Composite Design (CCD). The results of the optimization modeling study revealed that FFD yielded the most predictable and best-fitting results among all the models studied, with R2 values of 0.998 for ZnO and 0.993 for ZnO-ME. Notably, ZnO-ME exhibited a greater dye removal efficiency 80% than ZnO i.e., 71%, it may be due to the presence of amorphous carbon on the surface of ZnO-ME. Among the various isothermal models, the Freundlich model displayed the strongest correlation with the dye removal data, confirming the multilayer adsorption of dye on both nanoparticles and supporting physisorption. Therefore, ZnO and ZnO-ME nanoparticles have been proven as potential tools for mitigating environmental impacts associated with dye-containing wastewater.

Clay-polymer nanocomposites for effective water treatment: opportunities, challenges, and future prospects

The metal intoxication and its associated adverse effects to humans have led to the research for development of water treatment technologies from pollution hazards. Therefore, development of cheaper water remediation technologies is more urgent than ever. Clays and clay minerals are naturally occurring, inexpensive, non-toxic materials possessing interesting chemical and physical properties. As a result of interesting surface properties, these have been developed as efficient absorbent in water remediation. Recently, clay-polymer nanocomposites have provided a cost-effective technological platform for removing contaminants from water. Covering research advancements from past 25 years, this review highlights the developments in clay-polymer nanocomposites and their advanced technical applications are evaluated with respect to the background and issues in remediation of toxic metals and organic compounds from water. The extensive analysis of literature survey of more than two decades suggests that future work need to highlight on advancement of green and cost-effective technologies. The development of understanding of the interaction and exchange between toxin and clay-polymer composites would provide new assembly methods of nanocomposites with functional molecules or nanomaterials need to be extended to increase the detection and extraction limit to parts per trillion.

Zeolite 13X incorporated with Zn-Ce oxide nanocatalyst for removal of Reactive Red 120 dye: RSM-based approach

In this study, the photocatalytic removal of Reactive Red 120 (RR120) dye was examined using zeolite 13X incorporated with Zn-Ce under UV irradiation. The synthesis of Zn-Ce nanoparticles incorporated with zeolite 13X was conducted through the co-precipitation method, and the features of the prepared nanocatalyst were analyzed using various techniques. The SEM and BET analyses indicated successful incorporation of ZnO-Ce oxides on the surface of zeolite 13X and a specific surface area of 359.39 m2/gm, respectively. Further, the average size of crystal grains was 28 nm. The response surface methodology (RSM) approach was employed to optimize operating parameters. The quadratic model suggested by the RSM approach, characterized by a high regression coefficient (R2 = 0.9632), indicates a high level of reliability. Moreover, under optimal conditions (catalyst loading of 4 mg, pH of 3, H2O2 amount of 0.2 mL, UV power of 25 W, and reaction time of 60 min), the highest RR120 dye removal percentage was 99.97%. Kinetic data indicated an increase in the reaction rate constant from 0.0631 to 0.1796 min-1. The zeolite 13X incorporated with Zn-Ce photocatalyst exhibited excellent stability over 5 cycles, with only a 5.50% decrease in RR120 dye removal yield. This study demonstrates the promising potential of zeolite 13X incorporated with Zn-Ce nanoparticles for the removal of RR120 dye from aqueous suspension.

Enhanced photocatalytic performance of milkvetch-derived biochar via ZnO-Ce nanoparticle decoration for reactive blue 19 dye removal

In this research, the photocatalytic removal of reactive blue 19 (RB19) dye is investigated employing zinc oxide/cerium (ZnO@Ce) nanoparticles decorated with biochar under LED irradiation. Synthesis of ZnO@Ce nanoparticles decorated with biochar was performed utilizing the co-precipitation procedure and, then, the texture and morphology of the fabricated nanocomposite were analyzed using energy dispersive X-ray (EDX), field emission scanning electron microscopy (FE-SEM), X-ray powder diffraction (XRD), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), and Fourier transform infrared (FTIR) spectroscopy techniques. Moreover, FE-SEM images demonstrate that ZnO-Ce nanoparticles were successfully decorated on the surface of biochar. The specific surface areas of biochar and biochar/ZnO-Ce were 519.75 and 636.52 m2/g, respectively. To achieve the maximum yield in the removal of RB19 dye, the effects of operating variables including dye concentration, LED lamp power, biochar@ZnO-Ce catalyst dose, pH and H2O2 dose were explored. Besides, the maximum percentage of RB19 dye removal was 96.47% under optimal conditions, i.e. catalyst dosage of 100 mg, H2O2 dosage of 1 mL, pH of 9, initial dye concentration of 5 ppm, LED power of 50 W, and reaction time of 140 min. Furthermore, the kinetic analysis reveals that the removal of RB19 dye follows the pseudo-first order kinetic model, with calculated values of a reaction rate constant of 0.045 min-1 and a correlation coefficient of R2 = 0.99, respectively. Moreover, the reusability and recyclability of biochar@ZnO/Ce nanocatalyst was promising over five runs, with only a 6.08% decrease in RB19 dye removal efficiency. Therefore, it can be concluded that the biochar @ZnO/Ce photocatalyst can be promisingly applied for the removal of azo dyes in aqueous solutions.

Zinc oxide nanoparticles adsorb emerging pollutants (glyphosate pesticide) from aqueous solutions

The present study captures the precipitation synthesis of zinc nanoparticles and modification with alumina and oleic acid. The crystalline size evaluated from the XRD profile of the zinc oxide nanoparticles was 18.05 nm but was reduced to 14.20 and 14.50 nm upon modification with oleic acid and alumina. The XRD spectra also showed evidence of the amorphous nature of zinc oxide nanoparticles and subsequent enhancement upon modification. A porous appearance was observed in the SEM instrumentation but seems to be enhanced by modification. The FTIR absorption spectra of the nanoparticles showed a peak associated with ZnO vibration around 449 cm, but the enhanced intensity was observed due to modification. The prepared ZnO-NPs and the modified samples were good materials for the adsorption removal of glyphosate from water, recording efficiencies above 94% at neutral pH and showing a possible incremental trend with an enhanced period of contact and adsorbent dosage. The adsorbents showed maximum capacity that ranged from 82.85 to 82. 97 mg/g. The adsorption models of Freundlich, Temkin, Dubinin-Radushkevich and BET showed excellent fitness. Results from computational results complemented experimental data and were used to identify the sites for adsorption and characteristics of molecular descriptors for the systems.

Polarization Controlled Assembly of Ultrathin Thiorphan Nanostructures on ZnO Surface Facets

Despite the importance of thiorphan as a small molecule with vital biological roles, its interactions with zinc oxide (ZnO) nanomaterials that are prospective in drug delivery and theranostic applications have not yet been sufficiently explored. Here the impact of surface polarity of different ZnO facets on thiorphan adsorption is studied both experimentally by atomic force microscopy (AFM) and angle resolved X-ray photoelectron spectroscopy (XPS) and theoretically by force field molecular dynamics (FFMD) and density functional tight binding simulations (DFTB). Polar ZnO surfaces cause the formation of thiorphan nanodots, where the size of the nanodots depends on the direction of dipoles: small (4 nm) nanodots are formed on Zn-face ZnO, while large (25 nm) nanodots are formed on O-face ZnO. Nonpolar ZnO surfaces cause self-assembly into layered nanoislands with characteristic 4 nm layer thickness, which subsequently merge into rigid nanolayers. The self-assembly is shown to be controlled solely by the effect of surface dipole electric field orientation and magnitude, whereas effects of surface chemistry or solution are negligible. The results thus also show a way for controlling the assembly of thiorphan and other molecular nanomaterials for diverse applications.

Facile synthesis of biopolymer decorated magnetic coreshells for enhanced removal of xenobiotic azo dyes through experimental modelling

Since contamination of xenobiotics in water bodies has become a global issue, their removal is gaining ample attention lately. In the present study, nZVI was synthesized using chitosan for removal of two such xenobitic dyes, Bromocresol green and (BCG) and Brilliant blue (BB), which have high prevalence in freshwater and wastewater matrices. nZVI functionalization prevents nanoparticle aggregation and oxidation, enhancing the removal of BCG and BB with an efficiency of 84.96% and 86.21%, respectively. XRD, FESEM, EDS, and FTIR have been employed to investigate the morphology, elemental composition, and functional groups of chitosan-modified nanoscale-zerovalent iron (CS@nZVI). RSM-CCD model was utilized to assess the combined effect of five independent variables and determine the best condition for maximum dye removal. The interactions between adsorbent dose (2-4 mg), pH (4-8), time (20-40 min), temperature (35-65 0C), and initial dye concentration (40-60 mg/L) was modeled to study the response, i.e., dye removal percentage. The reaction fitted well with Langmuir isotherm and pseudo-first-order kinetics, with a maximum qe value of 426.97 and 452.4 mg/g for BCG and BB, respectively. Thermodynamic analysis revealed the adsorption was spontaneous, and endothermic in nature. Moreover, CS@nZVI could be used up to five cycles of dye removal with remarkable potential for real water samples.

Influence of adding zeolite loaded with different charges to semen extender on sperm quality in rabbits after cryopreservation

The aim of the present study was to investigate the effect of supplementing rabbit semen extender with zeolite loaded with different charges (Z⁺ or Z^-, Z^±) on sperm cryopreservation. Semen was collected from six healthy, fertile New Zealand rabbit bucks using an artificial vagina. The collected ejaculates were pooled and diluted with a tris-yolk fructose (TYF) extender supplemented with Z^± (+16, +12, +8, -16, -12, and -8) at a concentration of 1% for a final sperm concentration of 25 × 10⁶ sperm cells/mL. The diluted semen samples were then cryopreserved in 0.25 mL straws and stored in liquid nitrogen for 1 month. To evaluate sperm quality, we examined sperm progressive motility, vitality, morphological abnormalities, and plasma membrane integrity. In addition, apoptotic rates were determined using flow cytometry and by examining sperm ultrastructure under a transmission electron microscope (TEM). Moreover, total antioxidant capacity and markers of lipid peroxidation were measured in the extender after thawing. Addition of Z^± had a positive effect on progressive motility, vitality, and membrane integrity after an equilibration period and post-thawing as compared with the controls (P < 0.05). Z^± supplementation, particularly with a strong negative charge, also decreased the percentages of apoptotic and necrotic sperm cells compared to controls (P < 0.05), as shown both by flow cytometry and TEM. This was not associated with any marked effects on the oxidative biomarkers in the extender. In conclusion, addition of Z^± to semen extender improved post-thawing sperm quality by improving sperm characteristics, decreasing apoptosis, and minimizing sperm damage during cryopreservation.

Efficient adsorption of chlorpyrifos onto modified activated carbon by gamma irradiation; a plausible adsorption mechanism

Commercial Granulated Active Carbon (GAC) has been modified using 10 Gy dose Gamma irradiation (GAC10 Gy) for increasing its ability of air purification. Both, the raw and treated samples were applied for removing Chlorpyrifos pesticide (CPF) from ambient midair. Physicochemical properties of the two materials were characterized by Fourier Transform Infrared (FT-IR) and Raman spectroscopy. The phase formation and microstructure were monitored using X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), supported with Energy-Dispersive X-ray (EDX). The Surface area measurement was detected using BET particle size prosometry. Obtained outcomes showed that, the maximum adsorption capacity, given by Langmuir equations, was greatly increased from 172.712 to 272.480 mg/g for GAC and GAC10 Gy, respectively, with high selectivity. The overall removal efficiency of GAC10 Gy was notably comparable to that of the original GAC-sorbent. The present study indicated that, gamma irradiation could be a promising technique for treating GAC and turned it more active in eliminating the pesticides pollutants from surrounding air. The data of equilibrium has been analyzed by Langmuir and Freundlich models, that were considerably better suited for the investigated materials than other models. The process kinetics of CPF adsorbed onto both tested carbon versions were found to obey the pseudo first order at all concentrations with an exception at 70 mg/l using GAC, where, the spontaneous exothermic adsorption of Chlorpyrifos is a strong function for the pseudo-first order (PFO) and pseudo second order (PSO) kinetics.

One-pot synthesis of zinc oxide nanoparticles via chemical precipitation for bromophenol blue adsorption and the antifungal activity against filamentous fungi

In this research, zinc oxide nanoparticles (ZnONPs) were prepared via a facile one-pot chemical precipitation approach and applied in the adsorption of bromophenol blue (BRB) and as antifungal agents against the filamentous fungi and plant pathogens; Alternaria alternata CGJM3078, Alternaria alternata CGJM3006 and Fusarium verticilliodes CGJM3823. The ZnONPs were characterized by the UV-Vis, FTIR, XRD, TGA, BET, SEM, TEM, and EDX techniques, which showed efficient synthesis. The characteristics ZnO UV-Vis absorption band was observed at 375 nm, while the XRD showed an average ZnONPs crystalline size of 47.2 nm. The SEM and TEM images showed an irregular shaped and aggregated porous structure of 65.3 nm average-sized ZnONPs. The TGA showed 22.9% weight loss at 800 °C indicating the high thermal stability of ZnONPs, while BET analysis revealed a surface area, pore volume and pore diameter of 9.259 m2/g, 0.03745 cm3/g and 9.87 nm respectively. The Freundlich, pseudo-second-order, and intra-particle diffusion models showed R2 > 0.9494 and SSE < 0.7412, thus, exhibited the best fit to the isotherm and kinetics models. Thermodynamics revealed feasible, endothermic, random, and spontaneous adsorption of BRB onto the synthesized ZnONPs. The antifungal assay conducted depicts strong antifungal activities against all three tested fungi. Noticeably, ZnONPs (0.002-5 mg/mL) showed maximum activities with the largest zone of inhibition against A. alternata CGJM 3006 from 25.09 to 36.28 mm. This was followed by the strain F. verticilliodes CGJM 3823 (range from 23.77 to 34.77 mm) > A. alternata CGJM3078 (range from 22.73 to 30.63 mm) in comparison to Bleach 5% (positive control). Additionally a model was proposed based on the possible underlying mechanisms for the antifungal effect. This research demonstrated the potent use of ZnONPs for the adsorption of BRB and as effective antifungal agents.

Biogenic and chemically synthesized Solanum tuberosum peel-silver nanoparticle hybrid for the ultrasonic aided adsorption of bromophenol blue dye

This work was aimed at the synthesis of a hybrid (STpe-AgNP), obtained by impregnation of silver nanoparticles (AgNP) onto Solanum tuberosum peel (STpe), for the ultrasonic assisted adsorption of bromophenol blue (BB) dye. SEM, FTIR, XRD, EDX, TGA and BET techniques were used to characterize the adsorbents. The XRD, SEM and EDX confirmed successful impregnation of AgNPs onto STpe to form the hybrid. The AgNPs impregnated onto the hybrid were found to be water stable at various pH values of 2.0-9.0. Chi-square (χ2 < 0.024) and linear regression (R2 > 0.996) showed that the Freundlich model was best fitted among the isotherm models, corroborated by the oriented site model. Kinetic analysis conformed to the intraparticle diffusion and pseudo-first-order rate equations, while thermodynamics displayed a physical, spontaneous and endothermic adsorption process. The presence of competing Pb(II), Ni(II), Cd(II) and Zn(II) metal ions in solution interfered with the adsorption of BB onto the biosorbents. In terms of reusability, STpe and STpe-AgNP showed BB desorption of 91.3% and 88.5% respectively, using NaOH as eluent. Ultra-sonication significantly enhanced the adsorption of BB by both adsorbents, but the impregnation of AgNPs only slightly improved adsorption of the dye from the simulated wastewater. This study also illustrated that pristine STpe biomass waste is a cheap viable option for the decontamination of BB from water.

Enhanced photocatalytic activity of Ag-coated ZnO nanorods for the degradation of methylene blue

Worldwide water pollution is a serious issue, which needs special attention. Among these pollutants, methylene blue (MB) is dangerous for aquatic life as well as for human beings. Researchers are trying their best to degrade the various pollutants found in water. In the present work, we synthesized ZnO nanorods (NRDs) by one-step hydrothermal method. The synthesized samples were then characterized with the help of X-ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). ZnO nanostructures were composed of rod-shaped NRDs with flat edges and were highly crystalline with hexagonal shaped morphology. UV/Visible spectroscopy was carried out to investigate the optical properties, which shows the absorption in UV range and highly transmittance in the visible range. Finally, the photocatalytic activity was performed for the degradation of MB. The results show that MB was not fully degraded by bare ZnO NRDs. After all, we coated Ag NPs on the surfaces of ZnO NRDs through the simple solution-based method. The UV/Visible data reveal absorption in the UV as well as in the visible range due to the surface plasmonic effect of Ag NPs. Hybrid Ag-coated ZnO NRDs successfully degraded MB within 60 min. Therefore, we found that Ag-coated ZnO NRDs show good photocatalytic properties as compared to uncoated ZnO NRDs.

Dependence of the electrical properties of Cu-doped ZnO nanoparticles decorated by Ag atoms

Silver decorated copper doped zinc oxide nanoparticles (Ag@Cu-ZnO) were successfully prepared via sol gel method. X-ray diffraction analysis revealed ZnO wurtzite crystalline structure with the existence of minor peaks attributed to Cu and Ag. The presence of Cu and Ag in addition to ZnO lattice was supplementary verified by EDS data while the shift in the FTIR band confirmed the Cu incorporation within the ZnO host lattice. Both SEM and XRD revealed an increase in particle size with Ag loading. At different frequencies, electrical measurements demonstrated a decrement in the dielectric constant, dielectric loss and AC conductivity with the increment of Ag content. Meanwhile, the Nyquist plots of the impedance measurement showed a single semicircle arc indicating the predominance of grain boundary resistance. This study elucidated the great influence of Ag on Cu-doped ZnO nanoparticles’ structural, dielectric constant and electrical conductivity which make it a promising candidate for catalytic, photocatalytic and adsorption applications.

Dependence of the electrical properties of Cu-doped ZnO nanoparticles decorated by Ag atoms

Silver decorated copper doped zinc oxide nanoparticles (Ag@Cu-ZnO) were successfully prepared via sol gel method. X-ray diffraction analysis revealed ZnO wurtzite crystalline structure with the existence of minor peaks attributed to Cu and Ag. The presence of Cu and Ag in addition to ZnO lattice was supplementary verified by EDS data while the shift in the FTIR band confirmed the Cu incorporation within the ZnO host lattice. Both SEM and XRD revealed an increase in particle size with Ag loading. At different frequencies, electrical measurements demonstrated a decrement in the dielectric constant, dielectric loss and AC conductivity with the increment of Ag content. Meanwhile, the Nyquist plots of the impedance measurement showed a single semicircle arc indicating the predominance of grain boundary resistance. This study elucidated the great influence of Ag on Cu-doped ZnO nanoparticles’ structural, dielectric constant and electrical conductivity which make it a promising candidate for catalytic, photocatalytic and adsorption applications.

ZnO–TiO2: Synthesis, Characterization and Evaluation of Photo Catalytic Activity towards Degradation of Methyl Orange

Here in, we report the synthesis and characterization of ZnO–TiO2 composite as a potential photo catalyst for photo degradation of methyl orange under UV irradiation. ZnO–TiO2 with 1:1 ratio was synthesized via wet incipient impregnation method using TiO2 and Zn(NO3)2 ⋅ 6H2O as precursor material and the prepared composite was characterized by XRD, EDX and SEM. The synthesized composite was employed as photo catalyst for photo degradation of methyl orange. The photo degradation results showed that ZnO–TiO2 exhibited better catalytic performance than ZnO and TiO2 alone. The methyl orange photo degradation efficiency was determined to be 98, 75 and 60% over ZnO–TiO2, ZnO and TiO2 respectively using 50 mL solution of 100 mg/L at 40 °C for 120 min. The ZnO–TiO2 catalyzed photo degradation of methyl orange followed pseudo-first-order kinetic in terms of Langmuir–Hinshelwood mechanism.