Fruit peel incorporated alginate based magnetic hydrogel bio-composite beads for removal of hexavalent chromium

High adsorption capacity, reusability and sustainability are the most important features sought in the adsorbent preferences to be used in wastewater treatment. In this research work, magnetic composite beads prepared from fruit peels (nectarine and orange) and alginate (ALG) as biopolymers (NAF and OAF) were synthesized by dropping and pH-precipitation method as alternative adsorbents. By encapsulating the adsorbent using alginate and imparting magnetic properties, the separation of the adsorbent from water after the adsorption process has been simplified. Fourier transform infrared spectroscopy analysis (FTIR), scanning electron microscopy (SEM) analysis, energy-dispersive X-ray (EDX)-mapping and X-ray diffraction (XRD) analyses were performed to examine the surface chemical structure and surface morphological structure of these new synthesized biosorbents. The calculated maximum adsorption capacities were 224.3 mg/g for OAF and 256.5 mg/g for NAF at 298 K and pH =2.0. It was observed that the adsorption process for both adsorbents was endothermic and spontaneous. Moreover, the adsorptions of Cr (VI) onto both adsorbents followed the pseudo-second order model and fit the Langmuir isotherm model better. OAF and NAF were found to be reusable with stable adsorption capacity for at least five cycles. Overall, this study demonstrates the performance of OAF and NAF in the removal of Cr (VI) ions from aqueous solutions, thus highlighting the promising potential of these magnetic bio-based adsorbents for sustainable water treatment.

Synchronous bioremediation of vanadium(V) and chromium(VI) using straw in a continuous-flow reactor

Vanadium (V) and chromium (Cr) are key resources widely used in industrial production. However, mining causes V(V) and Cr(VI) contamination in groundwater, posing health and environmental risks. Straw is an important byproduct and considered waste, however, it could be a solid carbon source. Therefore, the feasibility of V(V) and Cr(VI) bioremediation in groundwater was determined using straw as the carbon source in this study. A continuous-flow reactor able to resist fluctuations in pollutant concentrations in groundwater was constructed. V(V) and Cr(VI) were completely removed (100%, 10-34 d) in the reactor, and the maximum Cr(VI) removal rate from effluent was 1.19 mg/(L·h) (34-64 d). After long-term reactor operation (114 d), the V(V) and Cr(VI) removal rates reached almost 100%. Moreover, the formation of humus and tryptophan contributed to V(V) and Cr(VI) bioremediation. The extracellular polymeric substance content increased from 108.28 to 113.98 mg/g VSS, and combined with V(V) and Cr(VI) to reduce their concentrations. Moreover, functional microbes associated with heavy metal removal (Bacillus and Pseudobacteroides) and straw decomposition (Paludibacter) were found. The findings of this study offer empirical evidence that support the utilization of straw for mitigating composite heavy metal pollution, thereby laying a foundation for its practical engineering applications.

A Comprehensive Review of Lab-Scale Studies on Removing Hexavalent Chromium from Aqueous Solutions by Using Unmodified and Modified Waste Biomass as Adsorbents

Anthropogenic activities and increasing human population has led to one of the major global problems of heavy metal contamination in ecosystems and to the generation of a huge amount of waste material biomass. Hexavalent chromium [Cr(VI)] is the major contaminant introduced by various industrial effluents and activities into the ecosystem. Cr(VI) is a known mutagen and carcinogen with numerous detrimental effects on the health of humans, plants, and animals, jeopardizing the balance of ecosystems. Therefore, the remediation of such a hazardous toxic metal pollutant from the environment is necessary. Various physical and chemical methods are available for the sequestration of toxic metals. However, adsorption is recognized as a more efficient technology for Cr(VI) remediation. Adsorption by utilizing waste material biomass as adsorbents is a sustainable approach in remediating hazardous pollutants, thus serving the dual purpose of remediating Cr(VI) and exploiting waste material biomass in an eco- friendly manner. Agricultural biomass, industrial residues, forest residues, and food waste are the primary waste material biomass that could be employed, with different strategies, for the efficient sequestration of toxic Cr(VI). This review focuses on the use of diverse waste biomass, such as industrial and agricultural by-products, for the effective remediation of Cr(VI) from aqueous solutions. The review also focuses on the operational conditions that improve Cr(VI) remediation, describes the efficacy of various biomass materials and modifications, and assesses the general sustainability of these approaches to reducing Cr(VI) pollution.

Rapid adsorptive removal of chromium from wastewater using walnut-derived biosorbents

Contamination of water resources by industrial effluents containing heavy metal ions and management of solid waste from agricultural and food industries is a serious issue. This study presents the valorization of waste walnut shells as an effective and environment-friendly biosorbent for sequestrating Cr(VI) from aqueous media. The native walnut shell powder (NWP) was chemically modified with alkali (AWP) and citric acid (CWP) to obtain modified biosorbents with abundant availability of pores as active centers, as confirmed by BET analysis. During batch adsorption studies, the process parameters for Cr(VI) adsorption were optimized at pH 2.0. The adsorption data were fitted to isotherm and kinetic models to compute various adsorption parameters. The adsorption pattern of Cr(VI) was well explained by the Langmuir model suggesting the adsorbate monolayer formation on the surface of the biosorbents. The maximum adsorption capacity, q_m, for Cr(VI) was achieved for CWP (75.26 mg/g), followed by AWP (69.56 mg/g) and NWP (64.82 mg/g). Treatment with sodium hydroxide and citric acid improved the adsorption efficiency of the biosorbent by 4.5 and 8.2%, respectively. The endothermic and spontaneous adsorption was observed to trail the pseudo-second-order kinetics under optimized process parameters. Thus, the chemically modified walnut shell powder can be an eco-friendly adsorbent for Cr(VI) from aqueous solutions.

Paracetamol and amoxicillin adsorptive removal from aqueous solution using phosphoric acid activated-carbon

Charcoal-based materials have attracted much attention for the removal of pharmaceutical agents. The charcoal-based carbon materials have green synthetic routes, high surface area, numerous active site with active functional groups available for physico-chemical interactions with adsorbate for surface-adsorptive removal of toxins. In this study, acid treated activated carbon was developed from the peach seeds using thermal pyrolysis approach. Phosphoric acid activated carbon (PAC) was further modified by HNO3 and employed as an adsorbent for the removal of amoxicillin and paracetamol and process variables were optimized for enhanced removal of amoxicillin and paracetamol. The adsorption of pharmaceutical agents was significantly affected by temperature, pH and reaction time. The amoxicillin and paracetamol sorption process onto PCA followed a pseudo second order kinetics and Langmuir isotherm model with a maximum removal capacity of 51.8 mg/g and 51.1 mg/g, respectively. The results revealed that acid activated carbon has promising efficiency for the removal of amoxicillin and paracetamol from aqueous medium and peach seeds derived PCA could be employed for the removal of these pharmaceutical agents from effluents and PAC is also extendable for the removal of other drugs from pharmaceutical wastewater streams.

Kinetic studies and conditions optimizations for the removal of direct red 80 dye from wastewater using cotton calyx and iron oxide composite

This study focusses on the adsorption efficiency of cotton pod (Gossypium arboreum) for biosorption of direct red (DR) 80 dye. The effect of dye concentration, pH, shaking time, adsorbent dose and temperature was considered to evaluate the adsorption efficiency of the cheapest raw material on the removal of dye. Various concentrations (10–50 ppm) were examined and maximum percentage removal of the adsorbent was obtained at pH 1 with adsorbent dose of 0.9 g and shaking time of 60 min. To enhance the adsorption efficiency of the adsorbent, the cotton calyx was treated with FeSO4.7H2O and investigated the removal of the raw adsorbent and the composite. It was examined that the removal efficiency of the composite is more than that of raw adsorbent. The composite was more efficient as dye removal reached up to 97%. FTIR of the composite shows an additional peak at 650 cm−1 for presence of Fe-O group and confirmation of composite formation. SEM micrograph showed that the particles in composite are more packed compared to the raw adsorbent. Mathematical models were applied and kinetic studies also have been done to provide better results regarding to the experimental data. It is concluded that the prepared adsorbent could be used as a tool for the removal of toxic pollutants from textile wastewater.

Extraction of silica from fly-ash and fabrication of silica-clay composite for dye removal and kinetic studies

A facile and green approach to extract silica from the coal fly-ash waste is extremely critical for environmental sustainability and economically suitable. In this study, we have used acid-alkali coupled approach to improvised the proficiency of the extraction process. The sodium hydroxide (NaOH) soaking results the formation of the sodium silicate (Na2SiO3) solution then pure silica was obtained by heating at high temperature; this coupled route-way results better yield of silica (SiO2) which is ∼ 40 g. The efficiency of pure silica is not enough to remove toxic effluents from the aqueous media. A highly versatile approach of composite formation was adopted to fabricate silica-clay composite using kaolinite-clay and extracted silica. Both materials, extracted silica and its silica-clay composite were analyzed using scanning electron microscopy (SEM), energy dispersive X-ray (EDX) method, X-ray diffraction technique (XRD) and Fourier transform infra-red spectroscopy (FTIR). The silica-clay composite showed plate-tubular like morphology with enormous binding sites available for the sorption pollutants like organic dyes. It has shown excellent sorption of methylene blue (MB) efficiency of 131.5 mg/g, while silica furnished the sorption of 70.5 mg/g. Results revealed that the synthesized material could probably have better potential for dye removal from industrial effluents.

Ultrasonic supported dye removal by a novel biomass

Sumac Leaves (Rhus Coriaria L), were used as a possible adsorbent of Basic Blue 3 (BB3) removal. The main affecting parameters on adsorption such as concentration, pH and temperature were investigated. Adsorption equilibrium was reached in 30 min. The ultrasonic effect was also enhanced the dyestuff removal. Adsorption capacity was rised from 0.566 to 1.826 mg/g, as rising the concentration from 4 μg/mL to 10 μg/mL. Several isotherm models including Langmuir, Freundlich and Temkin were applied for explaining the adsorption mechanism. Temkin and Langmuir isotherm models describe the system well. Pseudo first order, pseudo second order and intra particle kinetics were evaluated. Pseudo second order diffusion model supports the adsoprption and also intra particle diffusion plays an important role for BB3 removal. Thermodynamics of the adsorption were commented. −2219.5 J/mol of Gibbs energy showed us a spontaneous and physical adsorption.

Adsorption kinetics for the removal of toxic Congo red dye by polyaniline and citrus leaves as effective adsorbents

This study focusses on the synthesis of polyaniline (PANI) and polyaniline base adsorbent utilizing Citrus limon leaves (CL) powder. The polyaniline base adsorbent with C. limon was synthesized using the same process as polyaniline synthesis, but with the addition of leaves powder. PANI and PANI based adsorbent with C. limon leaves powder (PANI/CL) were characterized by Fourier Transform Infra-Red (FTIR), UV-Visible spectroscopy and Scanning Electron Microscopy (SEM). This synthesized material was employed for the removal of congo red (CR) dye from industrial wastewater. Furthermore, the Langmuir, Temkin and Freundlich isotherms were also applied to evaluate experimental results. PANI is an efficient adsorbent for CR removal with 71.9 mg/g, while PANI/CL is an efficient adsorbent with 80 mg/g removal of dye according to a comparison of maximal adsorption capabilities. The data concludes that the prepared adsorbents could possibly be employed for the removal of toxic dyes from industrial effluents at large scale and ultimately could help in improving the environment.

Microwave assisted green synthesis of ZnO nanoparticles using Rumex dentatus leaf extract: photocatalytic and antibacterial potential evaluation

In the present study, biological method was opted to synthesize ZnO NPs from Rumex dentatus plant. 0.1 M solution of zinc nitrate hexahydrate is mixed with the aqueous solution of R. dentatus plant leaves extract. The proportion of each solution was 1:1. Extract of plant leaves act as reducing agent. Firstly, the color changed from dark green to brown was observed and precipitates of light brown color appeared. Characterization of produced ZnO NPs was done using UV–Visible spectroscopy, scanning electron microscopy (SEM), energy dispersive X-rays (EDX) and X-ray diffraction (XRD) spectroscopy. The prepared ZnO NPS shows maximum absorption at 373 nm, in UV–Visible range. The shape of synthesized ZnO NPs is displayed by SEM. XRD analysis explains the average size of NPs is 6.19 nm. EDX tells about the percentage composition of synthesized ZnO NPs. Antibacterial analysis declared the NPs as good antibacterial agents. Photocatalytic activity of ZnO NPs was done using methyl orange dye. It was concluded that ZnO NPs can degrade toxic pollutants especially dyes.

Catalytic degradation of MO and MB dyes under solar and UV light irradiation using ZnO fabricated using Syzygium Cumini leaf extract

Zinc oxide nanoparticles (ZnO NPs) were fabricated using Syzygium cumini leave extract as a reducing and capping agent. The ZnO NPs were characterized using various techniques including scanning electron microscopy, UV-Visible and energy dispersive X-ray (EDX) techniques. The ZnO nanoparticles size was in 0.2–1 µm range and spherical in shape. Photocatalytic efficiency of ZnO NPs for the removal of MB (methylene blue) and MO (methyl orange) was investigated under solar and UV light expire. Photocatalytic efficiency of ZnO NPs was promising, which was found to be high under UV irradiation versus solar light. The ZnO NPs was confirmed as appropriate photocatalytic agent with significant potential for the removal of dye from wastewater.

Hydrothermal synthesis, characterization and photocatalytic activity of Mg doped MoS2

In this research work nanoparticles of Mg (0, 1, 2 and 3%) doped MoS2 are prepared by Hydrothermal method at 200 °C for 9 h. Scanning Electron Microscope (SEM) for surface morphology, Fourier Transform Infrared Spectroscopy (FTIR) for structural and chemical bonding and UV-visible spectroscopy for optical properties are used. SEM showed that sheet-like structure has changed into stone-like shaped when Mg has doped into MoS2. From FTIR, Mo–O, Mo=S, and H–O bond peaks are becoming dim and new chemical bonds S=O, Mo=O, Mg–O, CH and OH are forming with the increase of Mg doping. UV-visible spectroscopy showed that MoS2 has an indirect bandgap 2.21 eV. Band gap decreased from 1.84 to 1.82 eV when the Mg doping was increased from 1 to 2%, respectively. As Mg concentration was increased i.e. 3% then band gap increased to 1.88 eV. Photocatalytic activity (PCA) of undoped and Mg doped MoS2 is appraised by degrading rhodamine blue (RhB) and methylene blue (MB) dyes. The results showed that PCA (in presence of visible light) Mg doped MoS2 is greater than pure MoS2 which significantly increased the photocatalytic properties.

Greener approach to substitute chemical reduction clearing process for fabric dyed with Foron Blue E-BL 150, Foron Rubine RD-GFL and Foron Brilliant Yellow S-6GL using indigenous resources

Fabric dyed with disperse dyes followed a reduction clearing process (RCP)/chemical clearing process (CCP) to remove the unfixed dye from the fabric. In the clearing process, unfixed dyes and chemicals are discharged into streams. To combat this issue, an environment friendly approaches is explored that is a biological clearing using indigenous fungal strains of white-rot fungi (Pleurotus ostreatus and Ganoderma lucidum). In this context, fabrics dyed with three disperse dyes (Foron Blue E-BL 150, Foron Rubine RD-GFL and Foron Brilliant Yellow S-6GL) were considered. The fabric cleared with biological clearing process improved the quality of fabric versus chemically cleared fabric and among the tested strains, G. lucidum showed higher efficiency for color strength improvement. However, no significant difference in tensile and tear strength of all fabric samples was observed. The quality of effluents in clearing reduction process for three dyes was assessed and it was observed that water quality parameters including chemical oxygen demand (COD), total organic carbon (TOC), biological oxygen demand (BOD), total suspended solids (TSS), pH, dissolved oxygen (DO) and total dissolved solids (TDS) improved significantly and results revealed that the biological clearing approach can substitute chemical reduction clearing process for fabric dyed with dyes, which is greener and eco-friendly versus conventional processes to avoid unfixed dyes discharge in to water bodies.

Kinetics, equilibrium and thermodynamics of dyes adsorption onto modified chitosan: a review

In view of promising sorption capacity, stability, biodegradability, cost-effectiveness, environmental friendly nature, regeneration and recycling ability, the chitosan (CS) based adsorbents are highly efficient for the sequestration of dyes. Since CS offers variable chemical structures and CS have been modified by incorporating different moieties. The CS composites with unique properties have been employed successfully for dye adsorption with reasonably high adsorption capacity versus other similar adsorbents. Modifications of CS were promising for the preparation of composites that are extensively studied for their adsorption capacities for various dyes. This review highlights the CS and its modification and their applications for the adsorption of dyes. The removal capacities of CS-based adsorbents, equilibrium modeling, kinetics studies and the thermodynamic characteristics are reported. Moreover, the FTIR, BET, SEM, TGA and XRD were employed for the characterization of CS modified adsorbents are also discussed. Results revealed that the modified CS is highly efficient and can be employed for the sequestration of dyes from effluents.

Kinetics, equilibrium and thermodynamics of dyes adsorption onto modified chitosan: a review

In view of promising sorption capacity, stability, biodegradability, cost-effectiveness, environmental friendly nature, regeneration and recycling ability, the chitosan (CS) based adsorbents are highly efficient for the sequestration of dyes. Since CS offers variable chemical structures and CS have been modified by incorporating different moieties. The CS composites with unique properties have been employed successfully for dye adsorption with reasonably high adsorption capacity versus other similar adsorbents. Modifications of CS were promising for the preparation of composites that are extensively studied for their adsorption capacities for various dyes. This review highlights the CS and its modification and their applications for the adsorption of dyes. The removal capacities of CS-based adsorbents, equilibrium modeling, kinetics studies and the thermodynamic characteristics are reported. Moreover, the FTIR, BET, SEM, TGA and XRD were employed for the characterization of CS modified adsorbents are also discussed. Results revealed that the modified CS is highly efficient and can be employed for the sequestration of dyes from effluents.

ZnO, CuO and Fe2O3 green synthesis for the adsorptive removal of direct golden yellow dye adsorption: kinetics, equilibrium and thermodynamics studies

In the present investigation, ZnO, CuO and Fe2O3 were prepared via green route and utilized for the sequestration of DGY (Direct Golden Yellow) dye. Affecting variables i.e., temperature, contact time, adsorbent dose and pH were optimized for maximum sequestration of dye from aqueous medium. The pH 2, adsorbent dose 0.1 g/50 mL dye solution, temperature 30 °C and 50 mg/L dye initial concentration were best levels for efficient dye adsorption and equilibrium was attained in 30 min reaction time. The dye sequestration on to ZnO, CuO and Fe2O3 was an exothermic process. Freundlich and Temkin adsorption isotherms explained well the dye adsorption onto nanoadsorbents and dye adsorption followed pseudo first order kinetic model. Effect of electrolytes and heavy metal ions was also investigated and both affected the adsorption process significantly. In the presences of surfactant/detergent, the removal of dye was reduced and 0.5 N NaOH efficiently desorbed the dye from nanoadsorbents. Findings depicted that the nanoadsorbents are effectual for the sequestration of DGY dye, which can be employed for the remediation of textile effluents.