A comparison study on Acid Red 119 dye removal using two different types of waterworks sludge

Bioremediation of Textile Industrial Effluents Using Nutraceutical Industrial Spent: Laboratory-Scale Demonstration of Circular Economy

This research reports the first-ever study on abundantly available, environmentally friendly, low-cost and ready-for-use Nutraceutical Industrial Cumin Seed Spent (NICUS) as an innovative adsorbent for bioremediation of a bisazo Acid Red 119 (AR119) dye, a probable mutagen from textile industrial effluents (TIEs). The experiment at the laboratory scale is designed to suit the concepts of sustainability and valorisation under the domain of circular economy. The experimental qe value obtained was 96.00 mg g−1. The optimised conditions of parameters are as follows: pH of 2; adsorption time, 210 min; adsorbent dosage, 0.300 g L−1; particle size, 175 µM; initial dye concentration, 950 mg L−1; orbital shaking, 165 rpm and temperature, 50 °C, producing an impressive value of 748 mg of dye adsorbing on 1 g of dry NICUS. The adsorption capacity of NICUS obtained from the quadratic model developed for process optimisation gave values of 748 mg g−1. As a prelude to commercialisation, five variables that affect the adsorption process were experimentally studied. For the feasibility and efficiency of the process, a two-level fractional factorial experimental design (FFED) was applied to identify variables that influence the adsorption capacity of NICUS. The identified variables were applied to scale experiments by three orders. Nine isotherm models were used to analyse the adsorption equilibrium data. The Vieth–Sladek adsorption isotherm model was found to be the best fit. The pseudo-second-order reaction was the appropriate mechanism for the overall rate of the adsorption process. Mechanistic studies related to mass transfer phenomena were more likely to be dominant over the diffusion process. Techniques such as SEM, FTIR and CHN analysis were used to characterise NICUS. The dye-adsorbed NICUS obtained as “sludge” was used as a reinforcing material for the fabrication of composites using plastic waste. The physicomechanical and chemical properties of thermoplastic and thermoset composite using dye-adsorbed NICUS were evaluated and compared with NICUS composites. Prospects of integrating Small and Medium Enterprises (SMEs) into the circular economy of Nutraceutical Industrial Spent (NIS) are discussed.

Sustainable removal of anodized aluminum dye by groundwater treatment waste: experimental and modeling

Groundwater treatment waste (GWTW), as an environmentally friendly renewable nanomaterial, was implemented for the removal of anodized aluminum dye Sanodure Green (SG) from aqueous solutions. The capability of the SG metal complex dye removal was assessed by measuring solution decoloration and chromium elimination degree. GWTW was characterized using FTIR, SEM, EDX, TEM, XPS and surface area measurements. Kinetic curves were obtained by changing initial dye concentration, pH, temperature and adsorbent dose. Kinetic studies showed that up to 90 % of SG dye was removed within a contact time of 20 min. The adsorption of the dye was favourable at 293 K temperature in the acidic pH region (pH 1.5-2.0) with maximum adsorption capacity 185 mg g^-1. Langmuir-Freundlich isotherm model as well as hyperbolic tangent, diffusion-chemisorption and Elovich kinetic models accurately describe the dye removal process. The calculated thermodynamic parameters confirmed that SG dye removal occurred spontaneously and exothermically. The magnitude of enthalpy change (ΔH^° = -35.80 kJ mol^-1) was in agreement with the electrostatic interaction. The adsorption potential of GWTW for SG dye removal was also evaluated using a real wastewater produced after dyeing of anodized aluminum.

Application of response surface methodology in physicochemical removal of dyes from wastewater: A critical review

Response surface methodology (RSM) is a powerful tool in designing the experiments and optimizing different environmental processes. However, when it comes to wastewater treatment and specifically dye-containing wastewater, two questions arise; "Is RSM being used correctly?" and "Are all capabilities of RSM being exploited properly?". The current review paper aims to answer these questions by scrutinizing different physicochemical processes that utilized RSM in dye removal. The literature that applied RSM to adsorption, advanced oxidation processes, coagulation/flocculation and electrocoagulation processes were critically reviewed in this paper. The common errors in applying RSM to physicochemical removal of dyes are identified and some suggestions are made for future studies.

Comparison of photocatalytic degradation of dyes in relation to their structure

The photocatalytic degradation of a series of six acid dyes (Direct Red 80, Direct Red 81, Direct Red 23, Direct Violet 51, Direct Yellow 27, and Direct Yellow 50) has been tested compared in terms of color removal, mineralization, and toxicity (Lactuca sativa L. test) after photocatalysis on immobilized titanium dioxide. The dyes were examined at their natural pH and after hydrolysis at pH 12. Results show that hydrolysis decreases strongly the efficiency of color removal, that full mineralization takes much longer reaction time than color removal, and that toxicity is only very partially reduced. Some structural parameters, related to the structure and the topology of the dye molecules, could be correlated with the apparent color removal rates at natural pH.

A review on chemical coagulation/flocculation technologies for removal of colour from textile wastewaters

Textile industry is one of the most chemically intensive industries on the earth and the major polluter of potable water. It generates huge quantities of complex chemical substances as a part of unused materials including dyes in the form of wastewater during various stages of textile processing. The direct discharge of this wastewater into environment affects its ecological status by causing various undesirable changes. As environmental protection becomes a global concern, industries are finding novel solutions for developing technologies that can diminish the environmental damage. However, colour removal from textile wastewater by means of cheaper and environmental friendly technologies is still a major challenge. In this manuscript, several options of decolourisation of textile wastewater by chemical means have been reviewed. Based on the present review, some novel pre-hydrolysed coagulants such as Polyaluminium chloride (PACl), Polyaluminium ferric chloride (PAFCl), Polyferrous sulphate (PFS) and Polyferric chloride (PFCl) have been found to be more effective and suggested for decolourisation of the textile wastewater. Moreover, use of natural coagulants for textile wastewater treatment has also been emphasised and encouraged as the viable alternative because of their eco-friendly nature.

Post-treatment of anaerobically degraded azo dye Acid Red 18 using aerobic moving bed biofilm process: enhanced removal of aromatic amines

The application of aerobic moving bed biofilm process as post-treatment of anaerobically degraded azo dye Acid Red 18 was investigated in this study. The main objective of this work was to enhance removal of anaerobically formed the dye aromatic metabolites. Three separate sequential treatment systems were operated with different initial dye concentrations of 100, 500 and 1000 mg/L. Each treatment system consisted of an anaerobic sequencing batch reactor (An-SBR) followed by an aerobic moving bed sequencing batch biofilm reactor (MB-SBBR). Up to 98% of the dye decolorization and more than 80% of the COD removal occurred anaerobically. The obtained results suggested no significant difference in COD removal as well as the dye decolorization efficiency using three An-SBRs receiving different initial dye concentrations. Monitoring the dye metabolites through HPLC suggested that more than 80% of anaerobically formed 1-naphthylamine-4-sulfonate was completely removed in the aerobic biofilm reactors. Based on COD analysis results, at least 65-72% of the dye total metabolites were mineralized during the applied treatment systems. According to the measured biofilm mass and also based on respiration-inhibition test results, increasing the initial dye concentration inhibited the growth and final mass of the attached-growth biofilm in MB-SBBRs.