Paramagnetic Ionic Liquid/Metal Organic Framework Composites for CO2/CH4 and CO2/N2 Separations

Enhanced CO2 Capture through SAPO-34 Impregnated with Ionic Liquid

The concurrent utilization of an adsorbent and absorbent for carbon dioxide (CO2) adsorption with synergistic effects presents a promising technique for CO2 capture. Here, 1-butyl-3-methylimidazole acetate ([Bmim][Ac]), with a high affinity for CO2, and the molecular sieve SAPO-34 were selected. The impregnation method was used to composite the hybrid samples of [Bmim][Ac]/SAPO-34, and the pore structure and surface property of prepared samples were characterized. The quantity and kinetics of the sorbed CO2 for loaded samples were measured using thermogravimetric analysis. The study revealed that SAPO-34 could retain its pristine structure after [Bmim][Ac] loading. The CO2 uptake of the loaded sample was 1.879 mmol g-1 at 303 K and 1 bar, exhibiting a 20.6% rise compared to that of the pristine SAPO-34 recording 1.558 mmol g-1. The CO2 uptake kinetics of the loaded samples were also accelerated, and the apparent mass transfer resistance for CO2 sorption was significantly reduced by 11.2% compared with that of the pure [Bmim][Ac]. The differential scanning calorimetry method revealed that the loaded sample had a lower CO2 desorption heat than that of the pure [Bmim][Ac], and the CO2 desorption heat of the loaded samples was between 30.6 and 40.8 kJ mol-1. The samples exhibited good cyclic stability. This material displays great potential for CO2 capture applications, facilitating the reduction of greenhouse gas emissions.

A novel ionic liquid-entrapped MIL-101(Cr) framework with enhanced removal efficiency towards phosphate from aqueous solution

Developing adsorbent materials with high adsorptive dephosphorization (ADP) is significant for treating phosphate from aqueous solutions and eutrophic water. Herein, the MIL-101(Cr) framework was entrapped ionic liquid (IL) of 1-butyl-3-methylimidazoliumbromide ionic liquid ([C4mem]+[Br]-) using a ship-in-a-bottle approach to obtain novel adsorbents [C4mem]+[Br]-@MIL-101(Cr) contained varied IL contents, namely C4mem@MIL-101. The characterization results revealed that the formed [C4mem]+[Br]- molecules interacted with the MIL-101(Cr) frameworks, enhanced their stability, and offered additional adsorption sites. The batch adsorptions of phosphate showed that the optimized C4mem@MIL-101 adsorbent loaded with ~ 7% IL-based N content had the highest phosphate absorbing capacity of ~ 200 mg/g, outperforming the pristine MIL-101(Cr) and other adsorbents. The ADP efficiency was facilitated in the acidic media, where the phosphate ions of H2PO4- and HPO42- captured onto the C4mem@MIL-101 via several interactions, including electrostatic attraction, H-bonds, and chemical interactions. In the meantime, the coexisting anions diminished the phosphate adsorption because they competed with the pollutants at adsorption sites. Furthermore, phosphate treatment under the continuous fixed-bed conditions showed that 1 g of the polyvinyl alcohol (PVA)-mixed C4mem@MIL-101 pellets purified 25 l of water containing phosphate with a 1 mg/l concentration. The results suggest that the novel [C4mem]+[Br]-@MIL-101(Cr) structure had a high potential for treating phosphate in aqueous solutions.

Preparation of Polyimide/Ionic Liquid Hybrid Membrane for CO2/CH4 Separation

Imidazole ionic liquids (ILs) have good affinity and good solubility for carbon dioxide (CO2). Such ionic liquids, combined with polyimide membrane materials, can solve the problem that, today, CO2 is difficult to separate and recover. In this study, the ionic liquid (IL) of 1-ethyl-3-methylimidazolium tetrafluoroborate (IL1), 1-pentyl-3-methylimidazolium tetrafluoroborate (IL2), 1-octyl-3-methylimidazolium tetrafluoroborate (IL3), and 1-dodecylimidazolium tetrafluoroborate (IL4) with different contents were added to a polyimide matrix, and a series of polyimide membranes blended with ionic liquid were prepared using a high-speed mixer. The mechanical properties and gas separation permeability of the membranes were investigated. Among them, the selectivity of the PI/IL3 membrane for CO2/CH4 was 180.55, which was 2.5 times higher than the PI membrane, and its CO2 permeability was 16.25 Barrer, which exceeded the Robeson curve in 2008; the separation performance of the membrane was the best in this work.

Synthesis, Characterization, and Magnetic Properties of Lanthanide-Containing Paramagnetic Ionic Liquids: An Evan's NMR Study

The present study focuses on the synthesis and characterization of lanthanide-containing paramagnetic ionic liquids (ILs), [CnC1Im]3[MCl3X3] (n = 4, 6, and 8; M = Gd, Dy, and Ho; X = Br and Cl), derived from 1-alkyl-3-methylimidazolium anions. These paramagnetic ILs exhibit low vapor pressure, high thermal stability, physiochemical stability, and tunability, along with significant magnetic susceptibility, making them of interest in advanced material applications that may take advantage of neat liquids with magnetic susceptibility. Structural and physical properties were determined using FTIR, 1H NMR, DSC, and TGA. The room temperature density and viscosity of the iron paramagnetic ILs were also reported. Accompanying this report of paramagnetic IL products, we reintroduce and highlight Evan's NMR technique, an accessible magnetic susceptibility measurement technique that can utilize any available proton NMR to characterize the magnetic susceptibility of ILs. This work demonstrates the robustness of Evan's technique by demonstrating the ability to account for the IL water content, a common issue for hygroscopic materials, during the measurement of magnetic susceptibility. A detailed comparison of the ILs is presented, with dysprosium- and holmium-containing paramagnetic ILs exhibiting the highest magnetic susceptibility reported for mononuclear ILs reported to date. These materials have been studied with an eye on applications for mass transfer, eventually seeking to optimize magnetic susceptibility and viscosity using magnetic field gradients to move paramagnetic ILs carrying solute or heat. The study of paramagnetic ILs is important not only for understanding the magnetic properties of these materials but also for potential applications in areas such as magnetic resonance imaging, biomedicine, environmental remediation, and mass transfer. These unique materials have the potential to bring about new advances and technologies in the fields of materials science and analytical chemistry.

Ionic Liquids Functionalized MOFs for Adsorption

Metal-organic frameworks (MOFs) and ionic liquids (ILs) represent promising materials for adsorption separation. ILs incorporated into MOF materials (denoted as IL/MOF composites) have been developed, and IL/MOF composites combine the advantages of MOFs and ILs to achieve enhanced performance in the adsorption-based separation of fluid mixtures. The designed different ILs are introduced into the various MOFs to tailor their functional properties, which affect the optimal adsorptive separation performance. In this Perspective, the rational fabrication of IL/MOF composites is presented, and their functional properties are demonstrated. This paper provides a critical overview of an emergent class of materials termed IL/MOF composites as well as the recent advances in the applications of IL/MOF composites as adsorbents or membranes in fluid separation. Furthermore, the applications of IL/MOF in adsorptive gas separations (CO2 capture from flue gas, natural gas purification, separation of acetylene and ethylene, indoor pollutants removal) and liquid separations (separation of bioactive components, organic-contaminant removal, adsorptive desulfurization, radionuclide removal) are discussed. Finally, the existing challenges of IL/MOF are highlighted, and an appropriate design strategy direction for the effective exploration of new IL/MOF adsorptive materials is proposed.

Integrating Molecular Simulations with Machine Learning Guides in the Design and Synthesis of [BMIM][BF4]/MOF Composites for CO2/N2 Separation

Considering the existence of a large number and variety of metal-organic frameworks (MOFs) and ionic liquids (ILs), assessing the gas separation potential of all possible IL/MOF composites by purely experimental methods is not practical. In this work, we combined molecular simulations and machine learning (ML) algorithms to computationally design an IL/MOF composite. Molecular simulations were first performed to screen approximately 1000 different composites of 1-n-butyl-3-methylimidazolium tetrafluoroborate ([BMIM][BF₄]) with a large variety of MOFs for CO₂ and N₂ adsorption. The results of simulations were used to develop ML models that can accurately predict the adsorption and separation performances of [BMIM][BF₄]/MOF composites. The most important features that affect the CO₂/N₂ selectivity of composites were extracted from ML and utilized to computationally generate an IL/MOF composite, [BMIM][BF₄]/UiO-66, which was not present in the original material data set. This composite was finally synthesized, characterized, and tested for CO₂/N₂ separation. Experimentally measured CO₂/N₂ selectivity of the [BMIM][BF₄]/UiO-66 composite matched well with the selectivity predicted by the ML model, and it was found to be comparable, if not higher than that of all previously synthesized [BMIM][BF₄]/MOF composites reported in the literature. Our proposed approach of combining molecular simulations with ML models will be highly useful to accurately predict the CO₂/N₂ separation performances of any [BMIM][BF₄]/MOF composite within seconds compared to the extensive time and effort requirements of purely experimental methods.

Chemical similarity of dialkyl carbonates and carbon dioxide opens an avenue for novel greenhouse gas scavengers: cheap recycling and low volatility via experiments and simulations

Global warming linked to the industrial emissions of greenhouse gases may be the end of mankind unless it is adequately and timely handled. To prevent irreversible changes to the climate of the Earth, numerous research groups are striving to develop robust CO₂ sorbents. Dialkyl carbonates (DACs) and CO₂ exhibit obvious chemical similarities in their structure and properties. The degrees of oxidation of all atoms composing DACs and CO₂ are identical resulting in very similar nucleophilicities and electrophilicities of all interaction centers. While both compounds possess relatively high partial atomic charges on their polar moieties, the molecular geometries prevent tight binding of the head groups. The computed DAC-DAC binding energies are ∼40 kJ mol^-1, whereas the effect of the alkyl chain length is marginal. The phase transition points and shear viscosities of DACs are very low. We herein hypothesize and numerically rationalize that DACs represent noteworthy physical sorbents for CO₂ thanks to the similar sorbent-CO₂ and sorbent-sorbent interaction energies. By reporting in silico-derived sorption thermodynamics at various conditions, spectral and structural properties, and experimentally derived CO₂ capacities and recyclabilities, we highlight the mutual affinity of DACs and CO₂. Indeed, the experimentally determined CO₂ sorption capacity of 0.88 mol% (diethyl carbonate) at 278.15 K and 30 bar is competitive. The unprecedentedly low DAC-CO₂ binding energies, ∼14 kJ mol^-1, suggest a low-cost desorption process and outstanding recyclability of the sorbent. We also note that DACs possessing long alkyl chains (butyl, hexyl, octyl) exhibit negligible volatilities, while preserving the liquid aggregate state over a practically important temperature range. The reported results may foster the development of a new class of CO₂ scavengers with possibly quite peculiar characteristics.

Incorporated Metal–Organic Framework Hybrid Materials for Gas Separation, Catalysis and Wastewater Treatment

The special features of metal–organic frameworks (MOFs), namely, tunable porosity, exceptional structure, high surface area and high adsorption capability enable them to be widely studied in many applications including carbon capture and storage (CCS), biomedical engineering, catalysis and pollutant treatment. Despite these remarkable properties, MOFs are known to be moisture-sensitive, hardly recyclable and expensive in fabrication cost which limits their breakthrough performance in more efficient uses. Recently, extensive studies have been devoted to counter those shortcomings by embedding MOFs with support materials using various series of synthetic designs to yield incorporated MOF hybrid materials to counter their limitations. In view of this interest, this review summarizes the latest developments of incorporated MOFs with various materials, namely, ionic liquids (ILs), membranes and metal species. Pre-synthetic and post-synthetic synthesis methods are also discussed. This review also aims to highlight the factors associated with incorporated MOF performance such as materials selection and mass ratio which could have favorable effects in gas separation, catalysis and wastewater treatment applications. The data indicate that incorporated MOF hybrid materials exhibit exceptional properties including excellent robustness and stability. Correspondingly, in comparison to pristine MOFs, incorporated MOF hybrid materials significantly improve, among others, the gas selectivity, catalyst activity and dye removal efficiency in gas separation, catalysis and wastewater treatment, respectively. In addition, the challenge related to the utilization of this newly incorporated material is mentioned.

Effect of Thiouronium-Based Ionic Liquids on the Formation and Growth of CO2 (sI) and THF (sII) Hydrates

In this manuscript, two thiouronium-based ionic liquids (ILs), namely 2-ethylthiouronium bromide [C₂th][Br] and 2-(hydroxyethyl)thiouronium bromide [C₂OHth][Br], were tested at different concentrations (1 and 10 wt%) for their ability to affect CO₂ (sI) and tetrahydrofuran (THF) (sII) hydrate formation and growth. Two different methods were selected to perform a thermodynamic and kinetic screening of the CO₂ hydrates using a rocking cell apparatus: (i) an isochoric pressure search method to map the hydrate phase behavior and (ii) a constant ramping method to obtain the hydrate formation and dissociation onset temperatures. A THF hydrate crystal growth method was also used to determine the effectiveness of the ILs in altering the growth of type sII hydrates at atmospheric pressure. Hydrate–liquid–vapor equilibrium measurements revealed that both ILs act as thermodynamic inhibitors at 10 wt% and suppress the CO₂ hydrate equilibria ~1.2 °C. The constant ramping methodology provides interesting results and reveals that [C₂OHth][Br] suppresses the nucleation onset temperature and delays the decomposition onset temperatures of CO₂ hydrates at 1 wt%, whereas suppression by [C₂th][Br] was not statistically significant. Normalized pressure plots indicate that the presence of the ILs slowed down the growth as well as the decomposition rates of CO₂ hydrates due to the lower quantity of hydrate formed in the presence of 1 wt% ILs. The ILs were also found to be effective in inhibiting the growth of type sII THF hydrates without affecting their morphology. Therefore, the studied thiouronium ILs can be used as potential dual-function hydrate inhibitors. This work also emphasizes the importance of the methods and conditions used to screen an additive for altering hydrate formation and growth.

Unveiling the Temperature Influence on the Sorptive Behaviour of ZIF-8 Composite Materials Impregnated with [CnMIM][B(CN)4] Ionic Liquids

Composite sorbent materials (IL@MOF) with a metal-organic framework (MOF) ZIF-8 and [B(CN)4]−-based ionic liquids (ILs) were produced for the first time. Characterization results indicate the successful IL impregnation and conservation of the ZIF-8 crystalline structure and morphology. The data collected from the nitrogen (N2) physisorption at 77 K suggest that these IL@ZIF-8 materials are nonporous as their textural properties, such as BET specific surface area and total pore volume, are negligible. However, CO2, CH4, and N2 adsorption/desorption measurements in the IL@ZIF-8 composites at 303 and 273 K contradict the N2 data at 77 K, given that the obtained isotherms are Type I, typical of (micro)porous materials. Their gas adsorption capacity and ultramicroporous volume are in the same order of magnitude as the pristine microporous ZIF-8. The case study [C6MIM][B(CN)4] IL revealed a high affinity to both CO2 and CH4. This compromised the selectivity performance of its respective composite when compared with pristine ZIF-8. This work highlights the importance of accurate experimental gas adsorption/desorption equilibrium measurements to characterize the adsorption uptake and the porous nature of adsorbent materials.

Extensively amino-functionalized graphene captures carbon dioxide

Amino-functionalized graphene demonstrates certain potential to fix carbon dioxide.

Impact of Ionic Liquid Structure and Loading on Gas Sorption and Permeation for ZIF-8-Based Composites and Mixed Matrix Membranes

Carbon dioxide (CO2) capture has become of great importance for industrial processes due to the adverse environmental effects of gas emissions. Mixed matrix membranes (MMMs) have been studied as an alternative to traditional technologies, especially due to their potential to overcome the practical limitations of conventional polymeric and inorganic membranes. In this work, the effect of using different ionic liquids (ILs) with the stable metal-organic framework (MOF) ZIF-8 was evaluated. Several IL@ZIF-8 composites and IL@ZIF-8 MMMs were prepared to improve the selective CO2 sorption and permeation over other gases such as methane (CH4) and nitrogen (N2). Different ILs and two distinct loadings were prepared to study not only the effect of IL concentration, but also the impact of the IL structure and affinity towards a specific gas mixture separation. Single gas sorption studies showed an improvement in CO2/CH4 and CO2/N2 selectivities, compared with the ones for the pristine ZIF-8, increasing with IL loading. In addition, the prepared IL@ZIF-8 MMMs showed improved CO2 selective behavior and mechanical strength with respect to ZIF-8 MMMs, with a strong dependence on the intrinsic IL CO2 selectivity. Therefore, the selection of high affinity ILs can lead to the improvement of CO2 selective separation for IL@ZIF-8 MMMs.

Adsorption of Carbon Dioxide, Methane, and Nitrogen on Zn(dcpa) Metal-Organic Framework

Adsorption-based processes using metal-organic frameworks (MOFs) are a promising option for carbon dioxide (CO2) capture from flue gases and biogas upgrading to biomethane. Here, the adsorption of CO2, methane (CH4), and nitrogen (N2) on Zn(dcpa) MOF (dcpa (2,6-dichlorophenylacetate)) is reported. The characterization of the MOF by powder X-ray diffraction (PXRD), thermogravimetric analysis (TGA), and N2 physisorption at 77 K shows that it is stable up to 650 K, and confirms previous observations suggesting framework flexibility upon exposure to guest molecules. The adsorption equilibrium isotherms of the pure components (CO2, CH4, and N2), measured at 273–323 K, and up to 35 bar, are Langmuirian, except for that of CO2 at 273 K, which exhibits a stepwise shape with hysteresis. The latter is accurately interpreted in terms of the osmotic thermodynamic theory, with further refinement by assuming that the free energy difference between the two metastable structures of Zn(dcpa) is a normally distributed variable due to the existence of different crystal sizes and defects in a real sample. The ideal selectivities of the equimolar mixtures of CO2/N2 and CO2/CH4 at 1 bar and 303 K are 12.8 and 2.9, respectively, which are large enough for Zn(dcpa) to be usable in pressure swing adsorption.

Rethinking the Applications of Ionic Liquids and Deep Eutectic Solvents in Innovative Nano-Sorbents

With the development of green chemistry and nano materials, new alternatives to traditional volatile solvents are one of many important hotspots in the field of nano materials. Ionic liquids (ILs) and deep eutectic solvents (DESs) as excellent alternative solvents are being applied in the innovation of nano-sorbents, including nanoparticles, nanogels, and nanofluid. ILs and DESs are often used as carriers/modifiers/dispersers of nano-sorbents to enhance the adsorption capacity and selectivity in the extraction procedure. Various extraction technologies, such as solid-phase extraction, solid-phase microextraction, micro-solid phase extraction, hollow fiber liquid phase microextraction, and magnetic solid-phase extraction, have also been promoted by them to achieve rapid development. This paper focused on the latest development of nano-sorbents based on ILs and DESs. The problems and bottlenecks encountered were analyzed in order to provide meaningful and valuable references for the related research and thus promote further development and application of alternative solvents-assisted nano-sorbents.