Experimental Bioactive Glass-Containing Composites and Commercial Restorative Materials: Anti-Demineralizing Protection of Dentin

The Effect of Different pH and Temperature Values on Ca2+, F-, PO43-, OH-, Si, and Sr2+ Release from Different Bioactive Restorative Dental Materials: An In Vitro Study

Bioactive restorative materials are crucial for promoting remineralization and protecting dental tissues through ion release. This study examines how pH and temperature influence the short- and long-term ion (F-, Ca2+, Sr2+, OH-, Si, and PO43-) release from seven commercial materials: Cention Forte Filling Material, Cention Primer, Stela Self Cure, Riva Light Cure HV, Riva Self Cure, Equia Forte HT Fil, and Fuji IX GP Fast. Disks were prepared according to the manufacturers' instructions; immersed in buffer solutions at pH 4.8, 6.8, and 8.8; and stored at 37 °C and 44 °C. Ion release was measured after 1, 7, and 28 days using ion chromatography and mass spectrometry. Results revealed that ion release was significantly affected by pH, temperature, and exposure time. The highest fluoride (40.14 ± 0.32 mg/L) and calcium (74.23 ± 0.37 mg/L) releases were observed in Riva Light Cure at pH 4.8 and 44 °C after 28 days, with the highest strontium release (5.87 ± 0.06 mg/L) occurring under the same conditions. In contrast, silicon release peaked in Cention Forte Filling (31.72 ± 0.68 mg/L) at pH 4.8 and 37 °C. These findings highlight the impact of environmental factors on material performance, assisting clinicians in selecting optimal restorative materials for long-term dental health.

Effect of customized bioactive glass in experimental composites on dentin bond strength after 12 months of aging

OBJECTIVES

This study aimed to investigate the effect of a customized low-sodium bioactive glass (BG) fillers in experimental resin composites on their bond strength to dentin after 12 months of artificial aging. Specifically, it evaluated whether the bond strength was affected by different BG concentrations (0, 10, 20, 40 wt%) and artificial aging durations (1, 6, and 12 months).

MATERIALS AND METHODS

Experimental composites were prepared with 10, 20, and 40 wt% of a customized low-sodium fluoride-containing BG. The experimental composite with 0 wt% BG was used as a control, while Beautifil II (Shofu) was used as an external reference material. A universal adhesive system was applied to dentin substrates and composite build-ups were made. Bond strength was measured using a macro-shear bond strength test, and Weibull statistics were used to assess the reliability of the materials. Failure modes were analyzed to evaluate the type of the fracture.

RESULTS

After 12 months, the bond strength of all experimental composites remained stable and comparable to the control material, with statistically significant improvements between 6 and 12 months for all experimental materials. The bond strength was statistically similar across materials, except at the 12-month point, where the 20 wt% BG-composite showed significantly higher bond strength than the 40 wt% BG-composite. The frequency of mixed failures in composite increased after 12 months, particularly in experimental composites containing higher BG content.

CONCLUSIONS

The incorporation of a customized low- sodium BG into resin composites did not negatively impact their bond strength to dentin over 12 months. Instead, bond strength improved over time, and the composites remained mechanically stable, although a higher incidence of mixed failures was observed with increased BG content.

CLINICAL RELEVANCE

The customized low-sodium BG demonstrated stable bond strength over the 12-month period, offering a promising option for functional fillers in restorative composites without compromising the longevity of the adhesive-dentin interface.

Limitations, challenges and prospective solutions for bioactive glasses-based nanocomposites for dental applications: A critical review

Several nanomaterials have been recently used to overcome various challenges in the dental domain. Bioactive glasses, a class of bioceramics, with their outstanding properties including but not limited to their strong biocompatibility, antibacterial characteristics, and bioactivity inside the body's internal milieu have made them valuable biomaterials in a variety of dental domains. The utilization of nanomaterials has improved the performance of teeth, and the incorporation of bioactive glasses has the field of dentistry at an unsurpassed level in different categories such as esthetic and restorative dentistry, periodontics and dental implants, orthodontics, and endodontics. The current study discusses the most recent developments of the bioactive glasses' creation and implementation for dental applications, as well as the challenges and opportunities still facing the field. This work provides an overview of the current obstacles and potential future prospects for bioactive glasses-based nanocomposites to improve their dental uses. It also emphasizes the great potential synergistic effects of bioactive glasses used with other nanomaterials for dental applications.

Applications of smart materials in minimally invasive dentistry - some research and clinical perspectives

OBJECTIVES

Dental caries is one of the most prevalent bacteria-induced non-communicable diseases globally. It is known to be the top oral health burden in both developing and developed nations. There is substantial literature on the disease process and there is still debate on the extent of caries removal needed and the adequacy of the materials available to restore the lost tooth structure. The current review discusses the disease process together with the contemporary management of the carious lesion and also presents substantial evidence on novel materials and techniques that make minimally invasive dentistry predictable.

METHODS

The written work presented shows the most relevant literature for the management of dental caries focusing on novel materials used in minimally invasive dentistry.

RESULTS

There is still much to learn about specific antimicrobial and caries prevention mechanisms of novel materials. Materials that respond to a single or a few stimuli remain "weakly intelligent" in the face of the complex microenvironment in the oral cavity. Engineered systems that combine artificial intelligence and chemical engineering, are expected to possess higher intelligence, self-healing capabilities as well as environmental adaptability, and may be future promising research directions.

SIGNIFICANCE

The targeted approach in managing dental caries will hopefully have a better clinical outcome. The strategies discussed are alternatives to the contemporary approach and will improve the clinical management.

Environmental implications of dental restorative materials on the zebrafish Danio rerio: Are dental chair drainage systems an emerging environmental threat?

This study aimed to evaluate the environmental impact of dental materials: commercial composite Tetric EvoCeram®, glass ionomer Equia Forte® HT Fil, laboratory-prepared composite, alkasite Cention® Forte, amalgam Amalcap® Plus, and samples from dental chair drainage systems (DCDS). Methacrylate monomers were detected in the eluates of experimental and commercials composites, and alkasite. In DCDS samples solely mercury was found at concentrations of 0.08-1.86 μg/L. The experimental composite (48 h incubation) exhibited the highest toxicity on zebrafish Danio rerio (LC50=0.70 g/L), followed by amalgam (LC50=8.27 g/L) < Tetric EvoCeram® (LC50=10.94 g/L) < Equia Forte® HT Fil (LC50=24.84 g/L) < Cention® Forte (LC50=32.22 g/L). Exposure of zebrafish to DCDS samples resulted in decreased larval body length and increased occurrences of edema and blood accumulation. The results obtained highlight the need for additional monitoring and further research on the release of unreacted monomers and mercury from dental materials and their environmental impact.

Is Cention-N comparable to other direct dental restorative materials? A systematic review with network meta-analysis of in vitro studies

OBJECTIVES

To compare the performance of Cention-N® with direct restorative materials used at the daily practice (e.g., resin-based composites/RBC, glass ionomer cements/GIC, bioactive resins, silver amalgam) via a systematic review study.

METHODS

The review followed the PRISMA-NMA recommendations, and the protocol of the review was published at osf.io/ybde8. The search was conducted in PubMed/MEDLINE, Scopus, Web of Science, Embase, Lilacs, and SciELO databases, as well as in the grey literature (Open Grey, Proquest, and Periódicos CAPES). Studies with an in vitro experimental design evaluating the characteristics and properties of Cention-N in comparison to other restorative materials were included. The risk of bias of included studies was assessed using the RoBDEMAT tool, and meta-analyses were conducted using Review Manager 5.4 and MetaInsight V3 tools.

RESULTS

A total of 85 studies were included in the review, from which 79 were meta-analyzed. Several characteristics of direct restorative materials were analyzed, including physical (color change, degree of conversion, hardness, microleakage, polymerization rate, roughness, water solubility, water sorption), mechanical (bond strength to dentin, compressive strength, diametral tensile strength, flexural modulus, flexural strength, load-to-fracture, wear), and biological (alkalinizing effect, antibacterial activity, calcium and fluoride release) properties.

SIGNIFICANCE

Cention-N presented similar physico-mechanical properties compared to RBCs, but a stronger behavior than GICs. Despite the Alkasite nature of Cention-N, GICs may still demonstrate the greatest fluoride releasing ability from all direct restorative materials. This review confirmed the adequate behavior of Cention-N when compared to several other more traditionally used materials, confirming its applicability for the permanent restoration of decayed or fractured teeth.

Marginal integrity of prototype bioactive glass-doped resin composites in class II cavities

OBJECTIVES

This in vitro study examined the marginal integrity of experimental composite materials doped with bioactive glass (BG).

MATERIALS AND METHODS

Class-II MOD cavities were prepared and restored with one of the following composite materials: a commercial composite material as a reference (Filtek Supreme XTE), an experimental composite doped with BG 45S5 (C-20), and an experimental composite doped with a fluoride-containing BG (F-20). Six experimental groups (n = 8) were used, as each of the three composites was applied with (+) or without (-) a universal adhesive (Adper Scotchbond Multipurpose). All specimens were subjected to thermocycling (10,000 x, 5-55 °C) and then additionally stored in artificial saliva for eight weeks. Scanning electron micrographs of the mesial and the distal box were taken at three time points (initial, after thermocycling, and after eight weeks of storage in artificial saliva). The margins were classified as "continuous" and "non-continuous" and the percentage of continuous margins (PCM) was statistically analyzed (α = 0.05).

RESULTS

In most experimental groups, thermocycling led to a significant decrease in PCM, while the additional 8-week aging had no significant effect. F-20 + performed significantly better (p = 0.005) after 8 weeks storage in artificial saliva than the reference material with adhesive, while no statistically significant differences were observed at the other two time points. C-20 + exhibited significantly better PCM than the reference material with adhesive after thermocycling (p = 0.026) and after 8 weeks (p = 0.003).

CONCLUSIONS

Overall, the experimental composites with BG showed at least as good marginal adaptation as the commercial reference, with an indication of possible re-sealing of marginal gaps.

CLINICAL RELEVANCE

Maintaining or improving the marginal integrity of composite restorations is important to prevent microleakage and its likely consequences such as pulp irritation and secondary caries.

Mechanical Properties of Alkasite Material with Different Curing Modes and Simulated Aging Conditions

This study aimed to evaluate the micro-mechanical and macro-mechanical properties of self-cured and light-cured alkasite and to investigate how accelerated degradation in acidic, alkaline, and ethanol solutions affects the macro-mechanical properties of self-cured and light-cured alkasite. The specimens of the alkasite material (Cention Forte, Ivoclar Vivadent) were prepared according to the following three curing modes: (1) light-cured immediately, (2) light-cured after a 5-min delay, and (3) self-cured. Microhardness was tested before and after immersion in absolute ethanol to indirectly determine crosslink density, while flexural strength and flexural modulus were measured using a three-point bending test after accelerated aging in the following solutions: (1) lactic acid solution (pH = 4.0), (2) NaOH solution (pH = 13.0), (3) phosphate-buffered saline solution (pH = 7.4), and (4) 75% ethanol solution. The data were statistically analyzed using a two-way ANOVA and Tukey post hoc test. The results showed that the microhardness, flexural strength, and flexural modulus were significantly lower in self-cured specimens compared to light-cured specimens. A 5-min delay between the extrusion of the material from the capsule and light curing had no significant effect on any of the measured properties. A significant effect of the accelerated aging solutions on macro-mechanical properties was observed, with ethanol and alkaline solutions having a particularly detrimental effect. In conclusion, light curing was preferable to self-curing, as it resulted in significantly better micro- and macro-mechanical properties, while a 5-min delay between mixing the capsule and light curing had no negative effects.

POSS hybrid bioactive glass dental composite resin materials: Synthesis and analysis

INTRODUCTION

This study create a dental composite by hybirding polyhedral oligo-sesquioxide nano monomers and bioactive glass BG 45S5.

METHODS

Make an experimental composite resin material with a 60 % filler content overall by substituting 20 % of the filler with BG 45S5. The experimental resins are grouped and named P0, P2, P4, P6 and P8 based on the reactive nanomonomer methacrylic acid-based multifaceted oligomeric sesquisiloxane (POSS) added by 2 %-8 % in the resin matrix portion of each group. Utilize a universal testing machine to analyze and compare the mechanical properties of these, then perform Fourier infrared spectrum analysis, double bond conversion analysis, and scanning electron microscope analysis. Based on this, after soaking the experimental materials artificial saliva solution or lactic acid solution for a while, the pH changes of the solution, the release of Ca2+ and PO43- ions, and the precipitation of apatite on the resin material's surface were tested and analyzed. Cell viability tests were used to assess sample cell viability and quantify the cytotoxicity of biological cells. The independent sample t-test was used to examine the group comparisons, and a difference was considered statistically significant at P<0.05.

RESULTS

Outstanding mechanical and the double bond conversion are demonstrated by the nanocomposites when the POSS concentration hits 4 wt%. Agglomeration will cause the performance to deteriorate if the concentration beyond this threshold. In the P4 group, the double bond conversion, CS, and FS rose by a large margin, respectively, in comparison to the blank control group P0. Thankfully, the data demonstrate that adding POSS increases adhesive ability when compared to the blank group P0, however, there is no discernible difference between the other experimental groups. The acid neutralization capacity of the P4 group is essentially the same as that of the control group (P0). Ca2+ and PO43- ions are released in significant amounts following treatment with lactic acid solution, although this tendency is clearly less pronounced in artificial saliva. SEM and EDX data indicate that when the experimental resin is soaked in lactic acid solution and artificial saliva, apatite precipitation will happen on its surface. The results of the cell viability test indicated that there was no statistically significant difference between the experimental groups, and the viability of the cells increased after 24hours and 48 hours.

CONCLUSIONS

POSS was included into the composite resin along with 20% bioactive glass as a filler. When the proportion of POSS is less than 4%, the indices of composite resin materials rise in a dose-dependent way. When this value is surpassed, performance begins to deteriorate. The inclusion of POSS has no influence on the biological activity of the composites, which means that the hybrid composite resin is capable of acid neutralization, ion release, and apatite precipitation.

CLINICAL SIGNIFICANCE

The experimental composite resin can be used as an intelligent material in clinical treatment. It has the clinical application potential of preventing demineralization of tooth hard tissue, promoting remineralization, and improving edge sealing through apatite precipitation.

Comparative study of two bioactive dental materials

OBJECTIVES

New bioactive materials were introduced to not only restore the lost dental hard tissue but also to release fluoride that inhibits demineralization and occurrence of secondary caries. The current study thus aims to assess Fluoride release as well as the mechanical and physical properties of two new commercially available bioactive restorative materials.

METHODS

Two materials, Cention® Forte (CF) (Ivoclar Vivadent), Surefil one™ (SO) (Denstply Sirona), were evaluated in terms of fracture toughness (FT), flexural strength (FS), flexural modulus (FM) (ISO 4049), compressive strength (CS), and Vickers hardness (VH). In addition, thermogravimetric analysis (TGA) was performed, as well as pH measurements and quantification of Fluoride release after immersion in distilled water at times of 0, 7, 14 and 21 days. The sealing ability was evaluated using silver nitrate dye penetration on natural teeth. Finally, Energy-Dispersive X-Ray Spectroscopy (EDX) was used to investigate the surface composition of the two studied material surfaces. The data were statistically analyzed using Independent T-Tests; the chosen significance level was α = 0.05.

RESULTS

CF had significantly higher FT values compared to SO (p = 0.001). Also the FS results showed that CF had significantly higher values (90.11 MPa), followed by SO (22.15 MPa). The CS values showed the same order with significantly higher values for CF (231.79 MPa). While the FM and VH showed the reverse order with SO having significantly higher values than CF. pH measurements showed that CF evolved towards significantly higher pH values after 3 weeks in distilled water, while thermal properties showed more stability and higher resistance to degradation for CF compared to SO. The silver nitrate penetration results showed significantly better sealing ability for CF compared to the self-adhesive SO. Finally, EDX surface analysis results were consistent with the release profiles and confirmed the composition of the two tested materials.

SIGNIFICANCE

Both materials, demonstrated enhanced Fluoride release ability, and hence good remineralisation potential in vitro that could prevent recurrent carious lesions in vivo. The composition based on acrylic polymerization showed better mechanical resistance to bending and fracture, and higher sealing ability than those based on acid base reaction.

Water-Induced Changes in Experimental Resin Composites Functionalized with Conventional (45S5) and Customized Bioactive Glass

The aim of the study was to evaluate microhardness, mass changes during 1-year water immersion, water sorption/solubility, and calcium phosphate precipitation of experimental composites functionalized with 5-40 wt% of two types of bioactive glass (BG): 45S5 or a customized low-sodium fluoride-containing formulation. Vickers microhardness was evaluated after simulated aging (water storage and thermocycling), water sorption and solubility were tested according to ISO 4049, and calcium phosphate precipitation was studied by scanning electron microscopy, energy dispersive X-ray spectroscopy, and Fourier-transform infrared spectroscopy. For the composites containing BG 45S5, a significant reduction in microhardness was observed with increasing BG amount. In contrast, 5 wt% of the customized BG resulted in statistically similar microhardness to the control material, while higher BG amounts (20 and 40 wt%) resulted in a significant improvement in microhardness. Water sorption was more pronounced for composites containing BG 45S5, increasing 7-fold compared to the control material, while the corresponding increase for the customized BG was only 2-fold. Solubility increased with higher amounts of BG, with an abrupt increase at 20 and 40 wt% of BG 45S5. Calcium phosphate was precipitated by all composites with BG amounts of 10 wt% or more. The improved properties of the composites functionalized with the customized BG indicate better mechanical, chemical, and dimensional stability without compromising the potential for calcium phosphate precipitation.

Effects of an orthodontic primer containing amorphous fluorinated calcium phosphate nanoparticles on enamel white spot lesions

OBJECTIVES

The study investigated the effects of an orthodontic primer containing amorphous fluorinated calcium phosphate (AFCP) nanoparticles on enamel white spot lesions (WSLs).

MATERIALS AND METHODS

The AFCP nanoparticles were prepared and incorporated into Transbond XT Primer. Thirty-two human enamel slices were highly polished and randomly divided into four groups: no part covered (control), half covered with a primer containing 0 wt%, 25 wt%, and 35 wt% AFCP. Subsequently, samples were challenged by a modified pH-cycling and characterized by color measurement, micro-computed tomography, and scanning electron microscope (SEM). The bonding properties of the primers containing AFCP were assessed using shear bond strength test, and the mouse fibroblasts (L929) were employed to evaluate the cytotoxicity.

RESULTS

When the enamel was challenged by pH cycling, 25 wt% and 35 wt% AFCP groups exhibited less color change (ΔE) and less mineral loss than the control and 0 wt% AFCP groups. The SEM images showed that the original microstructural integrity and mineral deposition rate of the enamel surface were better in the 25 wt% and 35 wt% AFCP groups. In particular, the 35 wt% AFCP group exhibited the best performance after 3 weeks of pH cycling. The shear bond strength and cell viability revealed no significant difference among the tested groups (P > 0.05).

CONCLUSION

Using the primer containing 35 wt% AFCP might be a promising strategy for preventing the occurrence and development of WSLs during orthodontic treatment.

Bioactivity Potential of Bioceramic-Based Root Canal Sealers: A Scoping Review

INTRODUCTION

Bioceramic-based root canal sealers are novel materials with a bioactivity potential that stands out compared with conventional root canal sealers. However, the term bioactivity may be overused and is often misunderstood. Hence, the objective of this study was to synthesize and map key concepts related to the bioactivity analysis of bioceramic-based root canal sealers.

METHODS

The present scoping review is reported in accordance with the PRISMA-ScR Statement and is registered in the Open Science Framework. Two blinded reviewers carried out a comprehensive search in six databases up to January 10th, 2022: MEDLINE, Scopus, Embase, Web of Science, Cochrane Library, and Lilacs/BBO. Eligibility was considered for in vitro and in vivo studies that evaluated the bioactivity potential of bioceramic-based root canal sealers.

RESULTS

A total of 53 studies were included in the qualitative synthesis. In vitro bioactivity was evaluated through the mineralization potential, formation of carbonated apatite on the surface, and the gene expression related to proteins involved in the mineralization process. Meanwhile, for in vivo studies, staining techniques associated with immunohistochemical tests were mainly used to detect mineralization on the material-host tissue interface.

CONCLUSIONS

According to the methodology used, the most prevalent methods to assess bioactivity in acellular form were the immersion of the material in Hank's balanced salt solution, followed by surface observation with scanning electron microscopy and energy dispersive X-ray. In cell cultures, the chosen method was usually Alizarin Red staining, followed by the evaluation of alkaline phosphatase enzymatic activity and the use of molecular biology tests.

A Narrative Review of Bioactive Glass-Loaded Dental Resin Composites

This review aims to provide a comprehensive analysis of the characterizations of bioactive glass (BAG)-loaded dental resin-based composite materials. Online databases (Web of Science, PubMed, and Science Direct) were used to collect data published from January 2011 to January 2022. Only BAG-containing resin adhesive and resin restorative composites are discussed in this narrative review. BAG-loaded resin composites exhibit excellent mineralization ability reflecting enhanced ion release, pH elevation, and apatite formation, especially regarding high BAG loading. This aids the anti-demineralization and remineralization of teeth. Furthermore, BAG-loaded resin composites demonstrated in vitro biocompatibility and antibacterial performance. It has been suggested that BAG fillers with small particle sizes and no more than 20 wt% in terms of loading amount should be used to guarantee the appropriate mechanical properties of resin composites. However, most of these studies focused on one or some aspects using different resin systems, BAG types, and BAG amounts. As such, this makes the comparison difficult, and it is essential to find an optimal balance between different properties. BAG-loaded resin composites can be regarded as bioactive materials, which present major benefits in dentistry, especially their capability in the bacterial inhibition, cell biocompatibility, anti-demineralization, and remineralization of teeth.

Using Copper-Doped Mesoporous Bioactive Glass Nanospheres to Impart Anti-Bacterial Properties to Dental Composites

Experimental dental resin composites containing copper-doped mesoporous bioactive glass nanospheres (Cu-MBGN) were developed to impart anti-bacterial properties. Increasing amounts of Cu-MBGN (0, 1, 5 and 10 wt%) were added to the BisGMA/TEGDMA resin matrix containing micro- and nano-fillers of inert glass, keeping the resin/filler ratio constant. Surface micromorphology and elemental analysis were performed to evaluate the homogeneous distribution of filler particles. The study investigated the effects of Cu-MBGN on the degree of conversion, polymerization shrinkage, porosity, ion release and anti-bacterial activity on S. mutans and A. naeslundii. Experimental materials containing Cu-MBGN showed a dose-dependent Cu release with an initial burst and a further increase after 28 days. The composite containing 10% Cu-MBGN had the best anti-bacterial effect on S. mutans, as evidenced by the lowest adherence of free-floating bacteria and biofilm formation. In contrast, the 45S5-containing materials had the highest S. mutans adherence. Ca release was highest in the bioactive control containing 15% 45S5, which correlated with the highest number of open porosities on the surface. Polymerization shrinkage was similar for all tested materials, ranging from 3.8 to 4.2%, while the degree of conversion was lower for Cu-MBGN materials. Cu-MBGN composites showed better anti-bacterial properties than composites with 45S5 BG.

Improved Flexural Properties of Experimental Resin Composites Functionalized with a Customized Low-Sodium Bioactive Glass

This study evaluated the flexural properties of an experimental composite series functionalized with 5-40 wt% of a low-Na F-containing bioactive glass (F-series) and compared it to another experimental composite series containing the same amounts of the conventional bioactive glass 45S5 (C-series). Flexural strength and modulus were evaluated using a three-point bending test. Degree of conversion was measured using Fourier-transform infrared spectroscopy. Weibull analysis was performed to evaluate material reliability. The control material with 0 wt% of bioactive glass demonstrated flexural strength values of 105.1-126.8 MPa). In the C-series, flexural strength ranged between 17.1 and 121.5 MPa and was considerably more diminished by the increasing amounts of bioactive glass than flexural strength in the F-series (83.8-130.2 MPa). Analogously, flexural modulus in the C-series (0.56-6.66 GPa) was more reduced by the increase in bioactive glass amount than in the F-series (5.24-7.56 GPa). The ISO-recommended "minimum acceptable" flexural strength for restorative resin composites of 80 MPa was achieved for all materials in the F-series, while in the C-series, the materials with higher bioactive glass amounts (20 and 40 wt%) failed to meet the requirement of 80 MPa. The degree of conversion in the F-series was statistically similar or higher compared to that of the control composite with no bioactive glass, while the C-series showed a declining degree of conversion with increasing bioactive glass amounts. In summary, the negative effect of the addition of bioactive glass on mechanical properties was notably less pronounced for the customized bioactive glass than for the bioactive glass 45S5; additionally, mechanical properties of the composites functionalized with the customized bioactive glass were significantly less diminished by artificial aging. Hence, the customized bioactive glass investigated in the present study represents a promising candidate for functionalizing ion-releasing resin composites.

Effect of adhesive coating on calcium, phosphate, and fluoride release from experimental and commercial remineralizing dental restorative materials

This study investigated the potential of adhesive coating for hindering the reactivity of ion-releasing dental restorative materials. Experimental composites were prepared by replacing 10 or 20 wt% of reinforcing fillers with two types of bioactive glass. A glass ionomer, a giomer, and an alkasite were used as representatives of commercial ion-releasing materials. Restorative material specimens were coated with an etch-and-rinse adhesive, 1-step self-etch adhesive, 2-step self-etch adhesive, or left uncoated. The specimens were immersed in a lactic acid solution and ion concentrations were measured in 4 days intervals for 32 days (atomic absorption spectrometry for calcium, UV–Vis spectrometry for phosphate, ion-selective electrode for fluoride, and pH-meter for pH values). The adhesive coating reduced ion release between 0.3 and 307 times, in a significantly material- and adhesive-dependent manner. Fluoride release was most highly impaired, with the reduction of up to 307 times, followed by phosphate and calcium release, which were reduced up to 90 and 45 times, respectively. The effect of different adhesive systems was most pronounced for phosphate release, with the following rankings: uncoated ≥ 2-step self-etch adhesive ≥ 1-step self-etch adhesive ≥ etch-and-rinse adhesive. The differences among adhesives were less pronounced for calcium and fluoride. It was concluded that the resinous adhesive layer can act as a barrier for ion release and diminish the beneficial effects of remineralizing restorative materials.

Long-Term Assessment of Contemporary Ion-Releasing Restorative Dental Materials

The objective was to evaluate new commercially available ion-releasing restorative materials and compare them to established anti-cariogenic materials. Four materials were tested: alkasite Cention (Ivoclar Vivadent) in self-cure or light-cure mode, giomer Beautifil II (Shofu), conventional glass-ionomer Fuji IX (GC), and resin composite Tetric EvoCeram (Ivoclar Vivadent) as a control. Flexural strength, flexural modulus, and Weibull modulus were measured one day, three months, and after three months with accelerated aging in ethanol. Water sorption and solubility were evaluated for up to one year. Degree of conversion was measured during 120 min for self-cured and light-cured Cention. In this study, Beautifil II was the ion-releasing material with the highest flexural strength and modulus and with the best resistance to aging. Alkasite Cention showed superior mechanical properties to Fuji IX. Weibull analysis showed that the glass-ionomer had the least reliable distribution of mechanical properties with the highest water sorption. The solubility of self-cured alkasite exceeded the permissible values according to ISO 4049. Degree of conversion of light-cured Cention was higher than in self-cure mode. The use of alkasite Cention is recommended only in the light-cure mode.

The Effect of a Green Smoothie on Microhardness, Profile Roughness and Color Change of Dental Restorative Materials

Acidic drinks are known to exert negative effects on the surface properties of dental restorative materials. However, the effect of increasingly popular green smoothie drinks has not been addressed so far. The present study investigated the effect of cyclic immersions (5 min daily over 30 days) in a green smoothie drink on the surface properties of contemporary dental restorative materials, including resin composites, an alkasite, and a glass hybrid. Vickers microhardness, profile roughness, and perceptible color change in the CIE L* a* b* color space were evaluated as clinically relevant properties of the material surface. After 30-day green smoothie immersion, microhardness values either decreased by 8–28% (for resin composites) or increased by up to 91% (for glass hybrid). The increase in profile roughness (Ra parameter) of smoothie-immersed specimens was 7–26 times higher compared to the control group. The perceptible color change (ΔE*) in the smoothie group was 3–8 times higher compared to the control group. Overall, this study demonstrated that daily exposure of dental restorations made from resin composites, alkasites, and glass hybrid materials to a green smoothie drink can significantly accelerate material degradation, which is reflected as surface softening, as well as higher roughness and higher perceptible color change.

Ion release and hydroxyapatite precipitation of resin composites functionalized with two types of bioactive glass

OBJECTIVES

To prepare experimental composites with bioactive glass (BG) and investigate their release of calcium (Ca), phosphate (PO₄), and fluoride (F), as well as pH changes and apatite precipitation after immersion.

METHODS

Experimental composites were prepared with 0, 10, or 20 wt% of either BG 45S5 or a customized low-Na F-containing BG. Three commercial ion-releasing materials were used for reference. Material specimens were immersed in lactic acid (pH = 4.0) and artificial saliva (pH = 6.4). Ion concentrations (atomic absorption spectrometry for Ca, UV-vis spectrometry for PO₄, and ion-selective electrode for F) and pH were measured after 4, 8, 12, 16, 20, 24, 28, and 32 days. After immersion, composite specimens were analyzed using scanning electron microscopy (SEM) and Fourier-transform infrared (FTIR) spectroscopy.

RESULTS

Material-dependent concentrations of Ca, PO₄, and F were measured in the lactic acid solution, while a decrease of Ca and PO₄ concentrations was observed in artificial saliva. The uptake of ions from artificial saliva indicates their precipitation on specimen surfaces, which was supported by the results of SEM and FTIR investigations. In experimental composites functionalized with both bioactive glass types and a commercial "alkasite" material, apatite was precipitated not only in artificial saliva but also in the lactic acid solution.

CONCLUSIONS

Experimental BG-containing composites and selected commercial restorative materials demonstrated the potential for releasing multiple ion types and increasing pH.

CLINICAL SIGNIFICANCE

The observed effects can be beneficial for preventing demineralization and promoting remineralization of dental hard tissues, while apatite precipitation can additionally help in sealing marginal discontinuities.

Comparison of the effect of preheating on the flexural strength of giomer and nanohybrid composite resin

Background. Considering the increased use of preheating and novel resin-based materials to restore teeth, the present study investigated the impact of preheating on the flexural strength of a giomer and compared it with a nanohybrid composite resin. Methods. Two restorative materials (Beautifil II giomer and Alpha III nanohybrid composite resin) were used. Thirty rod-shaped samples (adding up to 60 samples) were prepared from the materials above and divided into two subgroups: with and without preheating (n=15). Before sample preparation, the giomer and nanohybrid composite resin tubes were preheated at 68ºC for 15 minutes in the preheating subgroups. In the subgroups without preheating, the tubes were kept in a room at 25ºC. Then the flexural strength was compared between the two groups with two-way ANOVA at a significance level of P<0.05. Results. The results showed significantly higher flexural strength in the preheated subgroups than in the non-preheated subgroups (P<0.001). In addition, the mean flexural strength values were significantly higher in the giomer groups than in the nanohybrid composite resin groups (P<0.001). Conclusion. Preheating increased the studied materials' flexural strengths significantly. The flexural strength of the giomer restorative material was higher than that of the nanohybrid composite resin, irrespective of preheating.