Biochar Nanoparticles over TiO2 Nanotube Arrays: A Green Co-Catalyst to Boost the Photocatalytic Degradation of Organic Pollutants

Methylene blue removal using modified poly(glycidyl methacrylate) as a low-cost sorbent in batch mode: kinetic and equilibrium studies

Industrial textile wastewater contains large amounts of cationic dye material. Therefore, a new adsorbent was synthesized as modified poly(glycidyl methacrylate) (mPGMA) with a fluorine group-containing compound 1,1,1,3,3,3-hexafluoro-2-propanol (HFIP). mPGMA was characterized by scanning electron microscopy (SEM) and Fourier transform infrared spectrometer (FTIR). The proposed adsorbent has been used to remove methylene blue (MB) from aqueous solutions by the adsorption process. In further experiments, the removal efficiency of adsorbent in both powder (˂600 μm) and granular form was compared from aqueous solutions by adsorption process. Furthermore, the effects of changing parameters such as adsorbent dosage, contact time, pH, temperature, and initial dye concentration on methylene blue adsorption were investigated. Also, Langmuir, Freundlich, and Temkin isotherms have been used to describe the equilibrium characteristics of adsorption. Finally, the experimental data fitted well by Langmuir isotherm with a maximum adsorption capacity of 17.5 mg g-1. The experimental data were applied to pseudo-first- and second-order models. The experimental results were better fitted for the pseudo-second-order model than the other model. Consequently, the experimental results showed that mPGMA is a suitable low-cost adsorbent with great potential benefit in removing methylene blue from aqueous solutions.

Empowering Adsorption and Photocatalytic Degradation of Ciprofloxacin on BiOI Composites: A Material-by-Design Investigation

Binary and ternary composites of BiOI with NH2-MIL-101(Fe) and a functionalized biochar were synthesized through an in situ approach, aimed at spurring the activity of the semiconductor as a photocatalyst for the removal of ciprofloxacin (CIP) from water. Experimental outcomes showed a drastic enhancement of the adsorption and the equilibrium (which increased from 39.31 mg g-1 of bare BiOI to 76.39 mg g-1 of the best ternary composite in 2 h time), while the kinetics of the process was not significantly changed. The photocatalytic performance was also significantly enhanced, and the complete removal of 10 ppm of CIP in 3 h reaction time was recorded under simulated solar light irradiation for the best catalyst of the investigated batch. Catalytic reactions supported by different materials obeyed different reaction orders, indicating the existence of different mechanisms. The use of scavengers for superoxide anion radicals, holes, and hydroxyl radicals showed that although all these species are involved in CIP photodegradation, the latter play the most crucial role, as also confirmed by carrying out the reaction at increasing pH conditions. A clear correlation between the reduction of BiOI crystallite sizes in the composites, as compared to the bare material, and the material performance as both adsorbers and photocatalyst was identified.

Dynamics of Diffusion- and Immobilization-Limited Photocatalytic Degradation of Dyes by Metal Oxide Nanoparticles in Binary or Ternary Solutions

Photocatalytic degradation employing metal oxides, such as TiO2 nanoparticles, as catalysts is an important technique for the removal of synthetic dyes from wastewater under light irradiation. The basic principles of photocatalysis of dyes, the effects of the intrinsic photoactivity of a catalyst, and the conventional non-fundamental factors are well established. Recently reported photocatalysis studies of dyes in single, binary, and ternary solute solutions opened up a new perspective on competitive photocatalytic degradation of the dyes. There has not been a review on the photocatalytic behavior of binary or ternary solutions of dyes. In this regard, this current review article summarizes the photocatalytic behavior of methylene, rhodamine B, and methyl orange in their binary or ternary solutions. This brief overview introduces the importance of the dynamics of immobilization and reactivity of the dyes, the vital roles of molecular conformation and functional groups on their diffusion onto the catalyst surface, and photocatalytic degradation, and provides an understanding of the simultaneous photocatalytic processes of multiple dyes in aqueous systems.

Recent Progress in Photocatalytic Removal of Environmental Pollution Hazards in Water Using Nanostructured Materials

Water pollution has become a critical issue because of the Industrial Revolution, growing populations, extended droughts, and climate change. Therefore, advanced technologies for wastewater remediation are urgently needed. Water contaminants are generally classified as microorganisms and inorganic/organic pollutants. Inorganic pollutants are toxic and some of them are carcinogenic materials, such as cadmium, arsenic, chromium, cadmium, lead, and mercury. Organic pollutants are contained in various materials, including organic dyes, pesticides, personal care products, detergents, and industrial organic wastes. Nanostructured materials could be potential candidates for photocatalytic reduction and for photodegradation of organic pollutants in wastewater since they have unique physical, chemical, and optical properties. Enhanced photocatalytic performance of nanostructured semiconductors can be achieved using numerous techniques; nanostructured semiconductors can be doped with different species, transition metals, noble metals or nonmetals, or a luminescence agent. Furthermore, another technique to enhance the photocatalytic performance of nanostructured semiconductors is doping with materials that have a narrow band gap. Nanostructure modification, surface engineering, and heterojunction/homojunction production all take significant time and effort. In this review, I report on the synthesis and characterization of nanostructured materials, and we discuss the photocatalytic performance of these nanostructured materials in reducing environmental pollutants.

Biochar-microorganism interactions for organic pollutant remediation: Challenges and perspectives

Numerous harmful chemicals are introduced every year in the environment through anthropogenic and geological activities raising global concerns of their ecotoxicological effects and decontamination strategies. Biochar technology has been recognized as an important pillar for recycling of biomass, contributing to the carbon capture and bioenergy industries, and remediation of contaminated soil, sediments and water. This paper aims to critically review the application potential of biochar with a special focus on the synergistic and antagonistic effects on contaminant-degrading microorganisms in single and mixed-contaminated systems. Owing to the high specific surface area, porous structure, and compatible surface chemistry, biochar can support the proliferation and activity of contaminant-degrading microorganisms. A combination of biochar and microorganisms to remove a variety of contaminants has gained popularity in recent years alongside traditional chemical and physical remediation technologies. The microbial compatibility of biochar can be improved by optimizing the surface parameters so that toxic pollutant release is minimized, biofilm formation is encouraged, and microbial populations are enhanced. Biocompatible biochar thus shows potential in the bioremediation of organic contaminants by harboring microbial populations, releasing contaminant-degrading enzymes, and protecting beneficial microorganisms from immediate toxicity of surrounding contaminants. This review recommends that biochar-microorganism co-deployment holds a great potential for the removal of contaminants thereby reducing the risk of organic contaminants to human and environmental health.

Effective Removal of Methylene Blue by Surface Alteration of TiO2 with Ficus Carica Leaf Extract under Visible Light

The present study describes the use of a leaf extract from Ficus carica as a source of natural antioxidants for the surface alteration of bulk titanium dioxide (TiO₂) in two steps. First, the hydro-thermal treatment of the bulk TiO₂ material was carried out and followed by thermal annealing at 300 °C for 3 h in air. The role of the leaf extract of Ficus carica on the performance of the bulk TiO₂ material for the removal of methylene blue (MB) was also studied. Various analytical techniques such as powder X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) were used to explore the crystalline structure, morphology, and composition. The bulk TiO₂ material after the leaf-extract treatment exhibited mixed anatase and rutile phases, a flower-like morphology, and Ti, O, and C were its main elements. The average crystallite size was also calculated, and the obtained values for the bulk TiO₂ material, 18.11 nm, and the treated bulk TiO₂ material with various amounts, 5, 10, and 15 mL, of leaf extract were 16.4, 13.16, and 10.29 nm respectively. Moreover, Fourier-transform infrared spectroscopy validated the typical metal-oxygen bonds and strengthened the XRD results. The bulk TiO₂ material chemically treated with Ficus carica has shown outstanding activity towards the degradation of MB under sunlight. The 15 mL of Ficus carica extract significantly enhanced the photocatalytic activity of the bulk TiO₂ material towards the degradation of MB. The dye degradation efficiency was found to be 98.8%, which was experimentally proven by the Fourier Transform Infrared spectroscopoyy (FTIR) analysis. The obtained performance of the bulk TiO₂ material with Ficus carica revealed excellent surface modifying properties for poorly-performing photocatalysts towards the degradation of synthetic dyes when used in their pristine form. The presented approach suggests that Ficus carica could be of great interest for tuning the surface properties of materials, either in the form of nano-size or bulk-phase in a particular application.

Rice Straw as Green Waste in a HTiO2@AC/SiO2 Nanocomposite Synthesized as an Adsorbent and Photocatalytic Material for Chlorpyrifos Removal from Aqueous Solution

A nano-HTiO2@activated carbon-amorphous silica nanocomposite catalyst (HTiO2@AC/SiO2) is utilized to photo breakdown catalytically and adsorb chlorpyrifos insecticide. SEM, TEM, and X-ray diffraction were used to examine HTiO2@AC/SiO2, synthesized through sol–gel synthesis. With an average size of 7–9 nm, the crystallized form of HTiO2 is the most common form found. At varied pH, catalyst doses, agitation speed, initial pesticide concentrations, contact periods, and temperatures, HTiO2@AC/SiO2 was examined for efficiency under visible light and in darkness. Because of the pseudo-second-order kinetics observed for chlorpyrifos, chemisorption is believed to dominate the adsorption process, as indicated by an estimated activation energy of 182.769 kJ/mol, which indicates that chemisorption dominates the adsorption process in this study. The maximal adsorption capacity of chlorpyrifos is 462.6 mg g−1, according to the Langmuir isotherms, which infer this value. When exposed to visible light, the adsorption capacity of HTiO2@AC/SiO2 increased somewhat as the temperature rose (283 k 323 k 373 k), indicating an exothermic change in Gibbs free energy during the process (−1.8 kJ/mol), enthalpy change (−6.02 kJ/mol), and entropy change (0.014 J/mol K), respectively, at 298.15 K. Negative (ΔS) describes a process with decreased unpredictability and suggests spontaneous adsorption. HTiO2@AC/SiO2 may be a promising material.

A Review of the Removal of Dyestuffs from Effluents onto Biochar

The study provides a review of various applications of biomass-derived biochars, waste-derived biochars, and modified biochars as adsorbent materials for removing dyestuff from process effluents. Processing significant amounts of dye effluent discharges into receiving waters can supply major benefits to countries which are affected by the water crisis and anticipated future stress in many areas in the world. When compared to most conventional adsorbents, biochars can provide an economically attractive solution. In comparison to many other textile effluent treatment processes, adsorption technology provides an economic, easily managed, and highly effective treatment option. Several tabulated data values are provided that summarize the main characteristics of various biochar adsorbents according to their ability to remove dyestuffs from wastewaters.

Exploring the Adsorption of Pb on Microalgae-Derived Biochar: A Versatile Material for Environmental Remediation and Electroanalytical Applications

Biochar, a carbon material obtained by pyrolysis of biomasses, is increasingly applied in environmental remediation and sensing thanks to its functional properties, cost-effectiveness and eco-friendliness. The adsorption capacity of biochar, strictly dependent on its specific surface area, heteroatom doping and surface functional groups, is crucial for these applications. Here, biochar produced at low temperature (350 °C) from a marine microalga (Nannochloropsis sp.) is proposed as an efficient adsorbent of lead (II) ions in aqueous solution; this production strategy promotes the natural self-doping of biochar without requiring harsh conditions. The kinetics and thermodynamics of the adsorption process, as well as the effect of pH, ionic strength and dissolved organic matter on the adsorption efficiency were systematically assessed. The microalgae-derived biochar shows superior adsorption performances compared to a nutshell-derived one (used as a reference of lignocellulosic feedstocks) under all the tested conditions. The microalgae-derived biochar was finally used to decorate screen-printed carbon electrodes to improve the electroanalytical performances towards the voltammetric detection of lead (II) ions. A two-fold increase in sensitivity was obtained compared to the unmodified electrode thanks to the enhanced electron transfer and adsorption properties provided by biochar. These results highlight the potentialities of microalgae-derived biochar for environmental and sensing applications.

Physicochemical Properties of Biochar Produced from Goldenrod Plants

Torrefaction is one of the methods of thermal treatment of biomass, which allows obtaining a product of better quality in the form of biochar. The aim of the paper was to analyze the possibility of using goldenrod (Solidago canadensis, Solidago gigantea) for the production of biochar. The torrefaction process involved the vegetative and generative parts as well as the whole plant at temperatures of 250 °C and 275 °C, for 3 h. Next, the physicochemical properties of the raw material and biochar were determined, namely moisture content, ash content, volatile matter content, calorific value, and heat of combustion. The bulk density of raw biomass and biochar was also determined. It was found that after biomass torrefaction, the ash content, calorific value, and heat of combustion increased, while volatile matter content decreased. It has been observed that in both the case of raw biomass and biochar, the plant species and the sampled parts have a significant impact on the ash content, volatile matter content, calorific value, and heat of combustion.

Removing the Oxamyl from Aqueous Solution by a Green Synthesized HTiO2@AC/SiO2 Nanocomposite: Combined Effects of Adsorption and Photocatalysis

The photocatalytic degradation and adsorption of the oxamyl pesticide utilizing a nano-HTiO2@activated carbon-amorphous silica nanocomposite catalyst (HTiO2@AC/SiO2). Sol-gel Synthesis was used to produce HTiO2@AC/SiO2, which was examined using Scanning Electron Microscopy, Transmission Electron Microscopy, and an X-ray diffractometer. The analyses confirmed that HTiO2 is mainly present in its crystalline form at a size of 7–9 nm. The efficiency of HTiO2@AC/SiO2 was assessed at various pHs, catalyst doses, agitating intensities, initial pesticide concentrations, contact times, and temperatures under visible light and in darkness. Oxamyl adsorption kinetics followed a pseudo-second-order kinetic model, suggesting that the adsorption process is dominated by chemisorption, as supported by a calculated activation energy of −182.769 kJ/mol. The oxamyl adsorption is compatible with Langmuir and Freundlich isotherms, suggesting a maximum adsorption capacity of 312.76 mg g−1. The adsorption capacity increased slightly with increasing temperature (283 K < 323 K < 373 K), suggesting an exothermic process with the Gibbs free energy change ΔG, enthalpy change ΔH, and entropy change ΔS°, being –3.17 kJ/mol, −8.85 kJ/mol, and −0.019 J/mol K, respectively, at 310 K for HTiO2@AC/SiO2 under visible light. This indicates spontaneous adsorption, and negative (ΔS) explain a decreased randomness process. HTiO2@AC/SiO2 would be a promising material.

Solvothermal Synthesis of ZnO Nanoparticles for Photocatalytic Degradation of Methyl Orange and p-Nitrophenol

The photocatalytic degradation of organic pollutants is an effective method of controlling environmental pollution. ZnO nanoparticles (ZnO NPs) were prepared by the solvothermal method and characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and UV–visible diffuse reflectance spectroscopy (UV–Vis DRS). The results showed that the ZnO NPs had a uniform size of 25–40 nm, hexagonal wurtzite structure, and a band gap of 2.99 eV. The photocatalytic degradation of methyl orange (MO) and p-nitrophenol (PNP) was used as a model reaction to evaluate the photocatalytic activity of ZnO NPs. The photocatalytic degradation rates (pseudo-first-order kinetics) of MO and PNP were 92% (0.0128 min−1) and 56.2% (0.0042 min−1), respectively, with a 25 W ultraviolet lamp, MO/PNP concentration = 20 mg/L, ZnO NPs dose = 1.5 g/L, and time = 180 min. The photocatalytic mechanism of ZnO NPs and degradation pathways of MO and PNP were also proposed. The results provide valuable information and guidance for the treatment of wastewater via photocatalytic methods.

Preparation of TiO2/Black Talc Composite Photocatalyst and the Research on Its Adsorption-Degradation Coupling Effects

In this paper, a TiO₂/black talc composite photocatalyst was prepared by the sol-gel method using TBOT as titanium source and black talc as carrier. Rhodamine B was used as the targeted pollutant to study the adsorption role of carbon in black talc. The results showed that with the adsorption-degradation cycles, the illumination time can be reduced by 40%. The adsorption rate and degradation rate of the composite photocatalyst was also increased. The degradation rate of Rhodamine B reached more than 95%, which fully shows the synergistic effect between TiO₂ nanoparticles and black talc. In this way, the adsorption-degradation coupling of the photocatalyst could be realized.