Oxygen Reduction Reaction and Hydrogen Evolution Reaction Catalyzed by Pd–Ru Nanoparticles Encapsulated in Porous Carbon Nanosheets

Enhanced durability of Pd/CeO2-C via metal-support interaction for oxygen reduction reaction

It is a challenge to improve the long-term durability of Pd-based electrocatalysts for oxygen reduction reaction (ORR) in fuel cells. Herein, Pd/CeO2-C-T (T= 800 °C, 900 °C and 1000 °C) hybrid catalysts with metal-support interaction are prepared from Ce-based metal organic framework precursor. Abundant tiny CeO2nanoclusters are produced to form nanorod structures with uniformly distributed carbon through a calcination process. Meanwhile, both carbon and CeO2nanoclusters have good contact with the following deposited surfactant-free Pd nanoclusters. Benefited from the large specific surface area, good conductivity and structure integrity, Pd/CeO2-C-900 exhibits the best electrocatalytic ORR performance: onset potential of 0.968 V and half-wave potential of 0.857 V, outperforming those obtained on Pd/C counterpart. In addition, the half-wave potential only shifts 7 mV after 6000 cycles of accelerated durability testing, demonstrating robust durability.

Electrocatalytic Properties of Quasi-2D Oxides LaSrMn0.5M0.5O4 (M = Co, Ni, Cu, and Zn) for Hydrogen and Oxygen Evolution Reactions

Designing cost-effective and highly efficient electrocatalysts for water splitting is a significant challenge. We have systematically investigated a series of quasi-2D oxides, LaSrMn0.5M0.5O4 (M = Co, Ni, Cu, Zn), to enhance the electrocatalytic properties of the two half-reactions of water-splitting, namely oxygen and hydrogen evolution reactions (OER and HER). The four materials are isostructural, as confirmed by Rietveld refinements with X-ray diffraction. The oxygen contents and metal valence states were determined by iodometric titrations and X-ray photoelectron spectroscopy. Electrical conductivity measurements in a wide range of temperatures revealed semiconducting behavior for all four materials. Electrocatalytic properties were studied for both half-reactions of water-splitting, namely, oxygen-evolution and hydrogen-evolution reactions (OER and HER). For the four materials, the trends in both OER and HER were the same, which also matched the trend in electrical conductivities. Among them, LaSrMn0.5Co0.5O4 showed the best bifunctional electrocatalytic activity for both OER and HER, which may be attributed to its higher electrical conductivity and favorable electron configuration.

Electrocatalytic Oxygen Reduction Reaction by the Pd/Fe-N-C Catalyst and Application in a Zn–Air Battery

Developing a non-platinum catalyst that effectively catalyzes the oxygen reduction reaction (ORR) is highly significant for metal–air batteries. Metal and nitrogen co-doped carbons (M-N-Cs) have emerged as alternative candidates to platinum. In this work, dual-metal Pd/Fe-N-C electrocatalysts were synthesized by the one-step pyrolysis of phytic acid, melamine, and Pd/Fe-based salts. The Pd/Fe-N-C catalyst exhibited a good catalytic ability during the ORR process and outperformed the commercial Pt/C catalyst as regards mass activity, catalytic stability, and methanol tolerance. It was found that Pd-Nx is the active center, and the synergistic effect from the Fe component introduction endowed the Pd/Fe-N-C with an excellent catalytic performance towards the ORR. When assembled into a Zn–air battery, its specific capacity was ~775 mAh gZn−1. Meanwhile, the peak power density could reach 3.85 W mgPd−1, i.e., 3.4 times that of the commercial Pt/C catalyst (1.13 W mgPt−1). This implies that the Pd/Fe-N-C catalyst has potential applications in metal–air batteries.

Ordered micropattern arrays fabricated by lung-derived dECM hydrogels for chemotherapeutic drug screening

AIMS

This study aims to evaluate ECM-coated micropattern arrays derived from decellularization of native porcine lungs as a novel three-dimensional cell culture platform.

METHODS

ECM derived from decellularization of native porcine lungs was exploited to prepare hydrogels. Then, dECM-coated micropattern arrays were fabricated at four different diameters (50, 100, 150 and 200 ​μm) using polydimethylsiloxane (PDMS). Two lung cancer cell lines, A549 and H1299, were tested on a dECM-coated micropattern array as a novel culture platform for cell adhesion, distribution, proliferation, viability, phenotype expression, and drug screening to evaluate the cytotoxicity of paclitaxel, doxorubicin and cisplatin.

RESULTS

The ECM derived from decellularization of native porcine lungs supported cell adhesion, distribution, viability and proliferation better than collagen I and Matrigel as the coated matrix on the surface. Moreover, the optimal diameter of the micropattern arrays was 100-150 ​μm, as determined by measuring the morphology, viability, proliferation and phenotype of the cancer cell spheroids. Cell spheroids of A549 and H1299 on dECM-coated micropattern arrays showed chemoresistance to anticancer drugs compared to that of the monolayer. The different distributions of HIF-1α, MCL-1 (in the center) and Ki-67 and MRP2 (in the periphery) of the spheroids demonstrated the good establishment of basal-lateral polarity and explained the chemoresistance phenomenon of spheroids.

CONCLUSIONS

This novel three-dimensional cell culture platform is stable and reliable for anticancer drug testing. Drug screening in dECM-coated micropattern arrays provides a powerful alternative to existing methods for drug testing and metabolic profiling in the drug discovery process.

Engineering Gold Nanostructures for Cancer Treatment: Spherical Nanoparticles, Nanorods, and Atomically Precise Nanoclusters

Cancer is a major global health issue and is a leading cause of mortality. It has been documented that various conventional treatments can be enhanced by incorporation with nanomaterials. Thanks to their rich optical properties, excellent biocompatibility, and tunable chemical reactivities, gold nanostructures have been gaining more and more research attention for cancer treatment in recent decades. In this review, we first summarize the recent progress in employing three typical gold nanostructures, namely spherical Au nanoparticles, Au nanorods, and atomically precise Au nanoclusters, for cancer diagnostics and therapeutics. Following that, the challenges and the future perspectives of this field are discussed. Finally, a brief conclusion is summarized at the end.

Bayesian Optimization of High-Entropy Alloy Compositions for Electrocatalytic Oxygen Reduction*

Active, selective and stable catalysts are imperative for sustainable energy conversion, and engineering materials with such properties are highly desired. High‐entropy alloys (HEAs) offer a vast compositional space for tuning such properties. Too vast, however, to traverse without the proper tools. Here, we report the use of Bayesian optimization on a model based on density functional theory (DFT) to predict the most active compositions for the electrochemical oxygen reduction reaction (ORR) with the least possible number of sampled compositions for the two HEAs Ag‐Ir‐Pd‐Pt‐Ru and Ir‐Pd‐Pt‐Rh‐Ru. The discovered optima are then scrutinized with DFT and subjected to experimental validation where optimal catalytic activities are verified for Ag–Pd, Ir–Pt, and Pd–Ru binary alloys. This study offers insight into the number of experiments needed for optimizing the vast compositional space of multimetallic alloys which has been determined to be on the order of 50 for ORR on these HEAs.

Nitrogen-Doped Reduced Graphene Oxide Supported Pd4.7Ru Nanoparticles Electrocatalyst for Oxygen Reduction Reaction

It is imperative to design an inexpensive, active, and durable electrocatalyst in oxygen reduction reaction (ORR) to replace carbon black supported Pt (Pt/CB). In this work, we synthesized Pd_4.7Ru nanoparticles on nitrogen-doped reduced graphene oxide (Pd_4.7Ru NPs/NrGO) by a facile microwave-assisted method. Nitrogen atoms were introduced into the graphene by thermal reduction with NH₃ gas and several nitrogen atoms, such as pyrrolic, graphitic, and pyridinic N, found by X-ray photoelectron spectroscopy. Pyridinic nitrogen atoms acted as efficient particle anchoring sites, making strong bonding with Pd_4.7Ru NPs. Additionally, carbon atoms bonding with pyridinic N facilitated the adsorption of O₂ as Lewis bases. The uniformly distributed ~2.4 nm of Pd_4.7Ru NPs on the NrGO was confirmed by transmission electron microscopy. The optimal composition between Pd and Ru is 4.7:1, reaching −6.33 mA/cm² at 0.3 V_RHE for the best ORR activity among all measured catalysts. Furthermore, accelerated degradation test by electrochemical measurements proved its high durability, maintaining its initial current density up to 98.3% at 0.3 V_RHE and 93.7% at 0.75 V_RHE, whereas other catalysts remained below 90% at all potentials. These outcomes are considered that the doped nitrogen atoms bond with the NPs stably, and their electron-rich states facilitate the interaction with the reactants on the surface. In conclusion, the catalyst can be applied to the fuel cell system, overcoming the high cost, activity, and durability issues.

Low content Ru-incorporated Pd nanowires for bifunctional electrocatalysis

This paper reports the facile synthesis and characterization of carbon supported Pd nanowires with low Ru contents (nRuPd/C). An anti-galvanic replacement reaction involving the reduction of Ru(iii) ions by nanoporous Pd nanowires to form nRuPd alloy nanowires was observed. A series of nRuPd/C materials with various Ru/Pd ratios were prepared by the spontaneous deposition of a Ru cluster on a Pd nanowire core using different Ru precursor concentrations (RuCl₃ = 0.5, 1.0, 5.0 mM). The successful formation of low content Ru-incorporated Pd nanowires without individual Ru clusters were confirmed using physicochemical characterization. The electrocatalytic activity of the nRuPd/C for the oxygen reduction reaction (ORR) and hydrogen evolution reaction (HER) in alkaline media was measured by RDE polarization experiments. The electrocatalytic activity varied greatly depending on the Ru content on the Pd nanowires. Among the catalysts, the prepared Pd nanowires incorporated with a very small amount of Ru (ca. 1.4 wt%) exhibited excellent electrocatalytic activity toward the ORR and HER: positive ORR/HER onset and E_1/2 potentials, higher n value, and lower Tafel slope.

The catalytic activity of Pd nanowires with low Ru contents showed superior bifunctional electrocatalytic performance towards both ORR and HER compared to the benchmarking Pt/C.

A strategy for preparing high-efficiency and economical catalytic electrodes toward overall water splitting

Electrolyzing water technology to prepare high-purity hydrogen is currently an important field in energy development. However, the preparation of efficient, stable, and inexpensive hydrogen production technology from electrolyzed water is a major problem in hydrogen energy production. The key technology for hydrogen production from water electrolysis is to prepare highly efficient catalytic, stable and durable electrodes, which are used to reduce the overpotential of the hydrogen evolution reaction and the oxygen evolution reaction of electrolyzed water. The main strategies for preparing catalytic electrodes include: (i) choosing cheap, large specific surface area and stable base materials, (ii) modulating the intrinsic activity of the catalytic material through elemental doping and lattice changes, and (iii) adjusting the morphology and structure to increase the catalytic activity. Based on these findings, herein, we review the recent work in the field of hydrogen production by water electrolysis, introduce the preparation of catalytic electrodes based on nickel foam, carbon cloth and new flexible materials, and summarize the catalytic performance of metal oxides, phosphides, sulfides and nitrides in the hydrogen evolution and oxygen evolution reactions. Secondly, parameters such as the overpotential, Tafel slope, active site, turnover frequency, and stability are used as indicators to measure the performance of catalytic electrode materials. Finally, taking the material cost of the catalytic electrode as a reference, the successful preparations are comprehensively compared. The overall aim is to shed some light on the exploration of high-efficiency and economical electrodes in energy chemistry and also demonstrate that there is still room for discovering new combinations of electrodes including base materials, composition lattice changes and morphologies.

Proposing an unbiased oxygen reduction reaction onset potential determination by using a Savitzky-Golay differentiation procedure

For proper and fair comparison of the performance of Oxygen reduction reaction (ORR) electrocatalysts an un-biased method to determine an onset potential value is needed. Here we report an easy mathematical approach based on the second derivative of linear sweep voltammetry curves, referred to as a second order discrete differentiation method (SODDM) that allows to accurately provide the onset potential. Analysis of the published results showed that the reported values might be affected by an intrinsic human error associated with the application of the most common approaches addressed as a tangent method or those relaying on a visual estimation of the onset potential based on the shape of a linear scan voltammetry (LSV) curve. We have also demonstrated that by using SODDM, electrochemical data collected on different instruments by different researchers leads to comparable results in terms of the ORR onset potential values.

Boosting the electrocatalytic activity of Pd/C by Cu alloying: Insight on Pd/Cu composition and reaction pathway

Tuning composition of Pd-based bimetallic electrocatalysts of high stability and durability is of great importance in energy-related reactions. This study reports the remarkable electrocatalytic performance of carbon-supported bimetallic Pd-Cu alloy nanoparticles (NPs) towards formic acid oxidation (FAO) and oxygen reduction reaction (ORR). Among various bimetallic compositions, Pd₃Cu/C alloy NPs exhibits the best FAO and ORR activity. During FAO reaction, Pd₃Cu/C alloy NPs exhibits a peak with a current density of 28.33 mA cm^-2 and a potential of 0.2 V (vs. Ag/AgCl) which is higher than that of the other PdCu compositions and standard 20 wt% Pd/C catalyst. Meanwhile, the onset potential (-0.09 V), half-wave potential (-0.18 V), limiting current density at 1600 rpm (-4.9 mA cm^-2) and Tafel slope (64 mV dec^-1) values of Pd₃Cu/C alloy NPs validate its superiority over the conventional 20 wt% Pt/C catalyst for ORR. Experimental and DFT studies have confirmed that the enhanced activity can be attributed to the electronic effect that arises after Cu alloying which causes a downshift of Pd d-band center and structural effect that produces highly dispersed NPs over the carbon matrix with high electrochemically active surface area.

Top 10 Cited Papers in the Section “Electrocatalysis”

This editorial is dealing with the most cited papers published in the years 2018–2019 in the section “Electrocatalysis” of the journal Catalysts [...]

MOF-Derived CuPt/NC Electrocatalyst for Oxygen Reduction Reaction

Metal-organic frameworks (MOFs) have been at the center stage of material science in the recent past because of their structural properties and wide applications in catalysis. MOFs have also been used as hard templates for the preparation of catalysts. In this study, highly active CuPt/NC electrocatalyst was synthesized by pyrolyzing Cu-tpa MOF along with Pt precursor under flowing Ar-H2 atmosphere. The catalyst was characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and X-ray powder diffraction (XRD). Rotating disk electrode study was performed to determine the oxygen reduction reaction (ORR) activity for CuPt/NC in 0.1 M HClO4 at different revolutions per minute (400, 800, 1200, and 1600) and it was also compared with commercial Pt/C catalyst. Further the ORR performance was evaluated by K-L plots and Tafel slope. CuPt/NC shows excellent ORR performance with onset potential of 0.9 V (vs. RHE), which is comparable with commercial Pt/C. The ORR activity of CuPt/NC is demonstrated as an efficient electrocatalyst for fuel cell.

Metallic Glass Films with Nanostructured Periodic Density Fluctuations Supported on Si/SiO2 as an Efficient Hydrogen Sorber

Nanostructured metallic glass films (NMGF) can exhibit surface and intrinsic effects that give rise to unique physical and chemical properties. Here, a facile synthesis and electrochemical, structural, and morphologic characterization of Pd-Au-Si based MGs of approximately 50 nm thickness supported on Si/SiO₂ is reported. Impressively, the maximum total hydrogen charge stored in the Pd-Au-Si nanofilm is equal to that in polycrystalline Pd films with 1 μm thickness in 0.1 m H₂ SO₄ electrolyte. The same NMGF has a volumetric desorption charge that is more than eight times and 25 % higher than that of polycrystalline PdNF and Pd-Cu-Si NMGF with the same thickness supported on Si/SiO₂ , respectively. A significant number of nanovoids originating from PdH_x crystals, and an increase in the average interatomic spacing is detected in Pd-Au-Si NMGF by high-resolution TEM. Such a high amount of hydrogen sorption is linked to the unique density fluctuations without any chemical segregation exclusively observed for this NMGF.

Dopamine Assisted One-Step Pyrolysis of Glucose for the Preparation of Porous Carbon with A High Surface Area

Herein, a facile dopamine assisted one-pot synthesis approach is proposed for the preparation of porous carbon with a specific surface area (SSA) up to 2593 m²/g through the direct pyrolysis of a mixture of glucose, NH₄Cl, and dopamine hydrochloride (DAH). The glucose is adopted as the carbon source and foaming agent, NH₄Cl is used as the blowing agent, and DAH is served as collaborative carbon precursor as well as the nitrogen source for the first time. The effect of dopamine on the component, structure, and SSA of the as-prepared porous carbon materials are systematically studied. The moderate addition of dopamine, which influences the condensation and polymerization of glucose, matches better with ammonium salt decomposition. The SSA of porous carbon increases first and then decreases with the increasing amount of dopamine. In our case, the porous carbon produced with 5 wt% dopamine (PC-5) achieves the maximum SSA of up to 2593 m²/g. Accordingly, it also shows the greatest electrochemical performance. The PC-5 shows a capacitance of 96.7 F/g calculated from the discharge curve at 1 A/g. It also has a good capacitive rate capacity, the specific capacitance can still maintain 80%, even at a high current density of 10 A/g. Moreover, PC-5 exhibits a good cycling stability of 98.1% capacitive retention after 1000 cycles. The proposed method may show promising prospects for preparing porous carbon materials as advanced energy storage materials, storage, and catalyst supports.