Nanostructured Ni Based Anode and Cathode for Alkaline Water Electrolyzers

Pd-Co-Based Electrodes for Hydrogen Production by Water Splitting in Acidic Media

To realize the benefits of a hydrogen economy, hydrogen must be produced cleanly, efficiently and affordably from renewable resources and, preferentially, close to the end-users. The goal is a sustainable cycle of hydrogen production and use: in the first stage of the cycle, hydrogen is produced from renewable resources and then used to feed a fuel cell. This cycle produces no pollution and no greenhouse gases. In this context, the development of electrolyzers producing high-purity hydrogen with a high efficiency and low cost is of great importance. Electrode materials play a fundamental role in influencing electrolyzer performances; consequently, in recent years considerable efforts have been made to obtain highly efficient and inexpensive catalyst materials. To reach both goals, we have developed electrodes based on Pd-Co alloys to be potentially used in the PEMEL electrolyzer. In fact, the Pd-Co alloy is a valid alternative to Pt for hydrogen evolution. The alloys were electrodeposited using two different types of support: carbon paper, to fabricate a porous structure, and anodic alumina membrane, to obtain regular arrays of nanowires. The goal was to obtain electrodes with very large active surface areas and a small amount of material. The research demonstrates that the electrochemical method is an ideal technique to obtain materials with good performances for the hydrogen evolution reaction. The Pd-Co alloy composition can be controlled by adjusting electrodeposition parameters (bath composition, current density and deposition time). The main results concerning the fabrication process and the characterization are presented and the performance in acid conditions is discussed.

Nickel-Based Electrocatalysts for Water Electrolysis

Currently, hydrogen production is based on the reforming process, leading to the emission of pollutants; therefore, a substitute production method is imminently required. Water electrolysis is an ideal alternative for large-scale hydrogen production, as it does not produce any carbon-based pollutant byproducts. The production of green hydrogen from water electrolysis using intermittent sources (e.g., solar and eolic sources) would facilitate clean energy storage. However, the electrocatalysts currently required for water electrolysis are noble metals, making this potential option expensive and inaccessible for industrial applications. Therefore, there is a need to develop electrocatalysts based on earth-abundant and low-cost metals. Nickel-based electrocatalysts are a fitting alternative because they are economically accessible. Extensive research has focused on developing nickel-based electrocatalysts for hydrogen and oxygen evolution. Theoretical and experimental work have addressed the elucidation of these electrochemical processes and the role of heteroatoms, structure, and morphology. Even though some works tend to be contradictory, they have lit up the path for the development of efficient nickel-based electrocatalysts. For these reasons, a review of recent progress is presented herein.

Copper nanowire array as highly selective electrochemical sensor of nitrate ions in water

Contamination of water with nitrate ions is a significant problem that affects many areas of the world. For this reason, European legislation has set the maximum permissible concentration of nitrates in drinking water at 44 mg/L. Thus, it is clear that a continuous monitoring of nitrate ions is of high technological interest but it must be rapid, easy to perform and directly performable in situ. In this work we have developed a nanostructured sensor based on array of copper nanowires obtained with the simple method of galvanic deposition. The nanostructured sensors have a very short response time with a detection limit less than 10 μM. Different interfering species were tested finding a negligible effect except for the chloride ions. However, this problem has been solved by removing chloride ions from the water through a simple precipitation of chloride compounds with low solubility. Nanostructured sensors were also used to analyze real water samples (rain, river and drinking water). In the case of drinking water, we have measured a concentration of nitrate ions very close to the that measured by conventional laboratory techniques.

Green Synthetic Fuels: Renewable Routes for the Conversion of Non-Fossil Feedstocks into Gaseous Fuels and Their End Uses

Innovative renewable routes are potentially able to sustain the transition to a decarbonized energy economy. Green synthetic fuels, including hydrogen and natural gas, are considered viable alternatives to fossil fuels. Indeed, they play a fundamental role in those sectors that are difficult to electrify (e.g., road mobility or high-heat industrial processes), are capable of mitigating problems related to flexibility and instantaneous balance of the electric grid, are suitable for large-size and long-term storage and can be transported through the gas network. This article is an overview of the overall supply chain, including production, transport, storage and end uses. Available fuel conversion technologies use renewable energy for the catalytic conversion of non-fossil feedstocks into hydrogen and syngas. We will show how relevant technologies involve thermochemical, electrochemical and photochemical processes. The syngas quality can be improved by catalytic CO and CO2 methanation reactions for the generation of synthetic natural gas. Finally, the produced gaseous fuels could follow several pathways for transport and lead to different final uses. Therefore, storage alternatives and gas interchangeability requirements for the safe injection of green fuels in the natural gas network and fuel cells are outlined. Nevertheless, the effects of gas quality on combustion emissions and safety are considered.