Toolpath Planning and Generation for Multi-Stage Incremental Forming Based on Stretching Angle

Finite Element Simplifications and Simulation Reliability in Single Point Incremental Forming

Single point incremental forming (SPIF) is one of the most promising technologies for the manufacturing of sheet metal prototypes and parts in small quantities. Similar to other forming processes, the design of the SPIF process is a demanding task. Nowadays, the design process is usually performed using numerical simulations and virtual models. The modelling of the SPIF process faces several challenges, including extremely long computational times caused by long tool paths and the complexity of the problem. Path determination is also a demanding task. This paper presents a finite element (FE) analysis of an incrementally formed truncated pyramid compared to experimental validation. Focus was placed on a possible simplification of the FE process modelling and its impact on the reliability of the results obtained, especially on the geometric accuracy of the part and bottom pillowing effect. The FE modelling of SPIF process was performed with the software ABAQUS, while the experiment was performed on a conventional milling machine. Low-carbon steel DC04 was used. The results confirm that by implementing mass scaling and/or time scaling, the required calculation time can be significantly reduced without substantially affecting the pillowing accuracy. An innovative artificial neural network (ANN) approach was selected to find the optimal values of mesh size and mass scaling in term of minimal bottom pillowing error. However, care should be taken when increasing the element size, as it has a significant impact on the pillow effect at the bottom of the formed part. In the range of selected mass scaling and element size, the smallest geometrical error regarding the experimental part was obtained by mass scaling of 19.01 and tool velocity of 16.49 m/s at the mesh size of 1 × 1 mm. The obtained results enable significant reduction of the computational time and can be applied in the future for other incrementally formed shapes as well.

Research on the Negative Multistage Incremental Forming of Straight-Wall Parts Based on the Extrusion from the Forward and Reverse Side of the Sheet

Because the forming area involved in traditional reverse multistage incremental forming is only located inside the model, the sheet-metal thinning rate is relatively large. Particularly, the straight-wall parts with a narrow internal space cannot be formed using traditional multistage incremental forming. Therefore, a negative multistage incremental forming that extrudes the sheet from the forward and the reverse side of the straight-wall part is proposed in this paper. In this method, firstly, the auxiliary surface is generated to divide the straight-wall part model into three forming regions; secondly, the first- and second-stage forming are carried out from the forward side of the straight-wall part with support, respectively; Thirdly, the third-stage forming is carried out from the forward side of the straight-wall part without support. The software system for auxiliary-surface generation, the straight-wall parts partition, each intermediate-stage-forming model, and each stage-forming toolpath generation was developed by using C++, VC++, and OpenGL library. In order to verify the feasibility of the proposed method in this paper, the forming experiments of a 1060 aluminum sheet were conducted using traditional reverse multistage forming and the proposed method in this paper, and the forming effects were compared and analyzed. The results show that compared with traditional reverse multistage incremental forming with forward-side extrusion, the multistage incremental forming method with the forward and the reverse-sided extrusion proposed in this paper can increase the area of the sheet participating in the deformation and avoid the problem of excessive thinning of sheet thickness, especially suitable for the straight-wall part model with narrow internal space.

Recent Developments and Future Challenges in Incremental Sheet Forming of Aluminium and Aluminium Alloy Sheets

Due to a favourable strength-to-density ratio, aluminium and its alloys are increasingly used in the automotive, aviation and space industries for the fabrication of skins and other structural elements. This article explores the opportunities for and limitations of using Single- and Two Point Incremental Sheet Forming techniques to form sheets from aluminium and its alloys. Incremental Sheet Forming (ISF) methods are designed to increase the efficiency of processing in low- and medium-batch production because (i) it does not require the production of a matrix and (ii) the forming time is much higher than in conventional methods of sheet metal forming. The tool in the form of a rotating mandrel gradually sinks into the sheet, thus leading to an increase in the degree of deformation of the material. This article provides an overview of the published results of research on the influence of the parameters of the ISF process (feed rate, tool rotational speed, step size), tool path strategy, friction conditions and process temperature on the formability and surface quality of the workpieces. This study summarises the latest development trends in experimental research on, and computer simulation using, the finite element method of ISF processes conducted in cold forming conditions and at elevated temperature. Possible directions for further research are also identified.