A Review of Transition Metal Sulfides as Counter Electrodes for Dye-Sensitized and Quantum Dot-Sensitized Solar Cells

A Numerical Simulation Study of the Impact of Kesterites Hole Transport Materials in Quantum Dot-Sensitized Solar Cells Using SCAPS-1D

Energy generation and storage are critical challenges for developing economies due to rising populations and limited access to clean energy resources. Fossil fuels, commonly used for energy production, are costly and contribute to environmental pollution through greenhouse gas emissions. Quantum dot-sensitized solar cells (QDSSCs) offer a promising alternative due to their stability, low cost, and high-power conversion efficiency (PCE) compared to other third-generation solar cells. Kesterite materials, known for their excellent optoelectronic properties and chemical stability, have gained attention for their potential as hole transport layer (HTL) materials in solar cells. In this study, the SCAPS-1D numerical simulator was used to analyze a solar cell with the configuration FTO/TiO2/MoS2/HTL/Ag. The electron transport layer (ETL) used was titanium dioxide (TiO2), while Cu2FeSnS4 (CFTS), Cu2ZnSnS4 (CZTSe), Cu2NiSnS4 (CNTS), and Cu2ZnSnSe4 (CZTSSe) kesterite materials were evaluated as HTLs. MoS2 quantum dot served as the absorber, with FTO as the anode and silver as the back metal contact. The CFTS material outperformed the others, yielding a PCE of 25.86%, a fill factor (FF) of 38.79%, a short-circuit current density (JSC) of 34.52 mA cm-2, and an open-circuit voltage (VOC) of 1.93 V. This study contributes to the advancement of high-performance QDSSCs.

Chalcogenides in Perovskite Solar Cells with a Carbon Electrode: State of the Art and Future Prospects

Perovskite solar cells (PSCs) have been on the forefront of advanced research for over a decade, achieving constantly increasing power conversion efficiencies (PCEs), while their route towards commercialization is currently under intensive progress. Towards this target, there has been a turn to PSCs that employ a carbon electrode (C-PSCs) for the elimination of metal back contacts, which increase the cost of corresponding devices while at the same time have a severe impact on their stability. Chalcogenides are chemical compounds that contain at least one chalcogen element, typically sulfur (S), selenium (Se), or tellurium (Te), combined with one metallic element. They possess semiconducting properties and have been proven to have beneficial effects when incorporated in a variety of solar cell types, including dye sensitized solar cells (DSSCs), quantum dot sensitized solar cells (QDSSCs), and Organic Solar Cells (OSCs), either as interlayers or added in the active layers. Currently, an increasing number of studies have highlighted their potential for achieving high-performing and stable PSCs. In this review, the most promising results of the latest studies regarding the implementation of chalcogenides in PSCs with a carbon electrode are presented and discussed, merging two research trends that are currently on the spotlight of solar cell technology.

Facile preparation of a CoNiS/CF electrode by SILAR for a high sensitivity non-enzymatic glucose sensor

The nanomaterials for non-enzymatic electrochemical sensors are usually pre-synthesized and coated onto electrodes by ex situ methods. In this work, amorphous cobalt-nickel sulfide (CoNiS) nanoparticles were facilely prepared on copper foam (CF) by the in situ successive ionic layer adsorption and reaction (SILAR) method, and as-prepared CoNiS/CF was studied as an electrode for non-enzymatic glucose sensing. It was analyzed by field emission scanning electron microscopy (FESEM), energy dispersive X-ray analysis (EDAX) and X-ray photoelectron spectroscopy (XPS). The electrochemical performance was investigated by cyclic voltammetry (CV) and chronoamperometry (CA). This binary sulfide electrode showed better performance toward glucose oxidation compared to the corresponding single sulfide and showed a wide linear range of 0.005 to 3.47 mM, a high sensitivity of 2298.7 μA mM-1 cm-2 and a low detection limit of 2.0 μM. The sensor exhibited high sensitivity and good repeatability and stability and was able to detect glucose in an actual sample. This work provides a simple and fast in situ electrode preparation method for a high-sensitivity glucose sensor.

Efficient One-Step Synthesis of a Pt-Free Zn0.76Co0.24S Counter Electrode for Dye-Sensitized Solar Cells and Its Versatile Application in Photoelectrochromic Devices

In this study, we synthesized a ternary transition metal sulfide, Zn0.76Co0.24S (ZCS-CE), using a one-step solvothermal method and explored its potential as a Pt-free counter electrode for dye-sensitized solar cells (DSSCs). Comprehensive investigations were conducted to characterize the structural, morphological, compositional, and electronic properties of the ZCS-CE electrode. These analyses utilized a range of techniques, including X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy. The electrocatalytic performance of ZCS-CE for the reduction of I3- species in a symmetrical cell configuration was evaluated through electrochemical impedance spectroscopy and cyclic voltammetry. Our findings reveal that ZCS-CE displayed superior electrocatalytic activity and stability when compared to platinum in I-/I3- electrolyte systems. Furthermore, ZCS-CE-based DSSCs achieved power conversion efficiencies on par with their Pt-based counterparts. Additionally, we expanded the applicability of this material by successfully powering an electrochromic cell with ZCS-CE-based DSSCs. This work underscores the versatility of ZCS-CE and establishes it as an economically viable and environmentally friendly alternative to Pt-based counter electrodes in DSSCs and other applications requiring outstanding electrocatalytic performance.