Preparation and Properties of Thin-Film Composite Forward Osmosis Membranes Supported by Cellulose Triacetate Porous Substrate via a Nonsolvent-Thermally Induced Phase Separation Process

Preparation, Modification, and Application of Ethylene-Chlorotrifluoroethylene Copolymer Membranes

Ethylene-chlorotrifluoroethylene (ECTFE) was first commercialized by DuPont in 1974. Its unique chemical structure gives it high heat resistance, mechanical strength, and corrosion resistance. But also due to these properties, it is difficult to prepare a membrane from it by the nonsolvent-induced phase separation (NIPS) method. However, it can be prepared as a microfiltration membrane using the thermally induced phase separation (TIPS) method at certain temperatures and with the selection of suitable solvents, and the use of green solvents is receiving increasing attention from researchers. The surface wettability of ECTFE membranes usually needs to be modified before use to strengthen its performance to meet the application requirements, usually by graft modification and surface oxidation techniques. This paper provides an overview of the structure of ECTFE and its preparation and modification methods, as well as recent advances in its application areas and prospects for the future methods of preparing high-performance ECTFE membranes.

Development of Support Layers and Their Impact on the Performance of Thin Film Composite Membranes (TFC) for Water Treatment

Thin-film composite (TFC) membranes have gained significant attention as an appealing membrane technology due to their reversible fouling and potential cost-effectiveness. Previous studies have predominantly focused on improving the selective layers to enhance membrane performance. However, the importance of improving the support layers has been increasingly recognized. Therefore, in this review, preparation methods for the support layer, including the traditional phase inversion method and the electrospinning (ES) method, as well as the construction methods for the support layer with a polyamide (PA) layer, are analyzed. Furthermore, the effect of the support layers on the performance of the TFC membrane is presented. This review aims to encourage the exploration of suitable support membranes to enhance the performance of TFC membranes and extend their future applications.

Development and Industrial-Scale Fabrication of Next-Generation Low-Energy Membranes for Desalination

Spiral-wound modules have been the most common configuration of packing flat-sheet membranes since the early development of polyamide (PA) membranes for water treatment applications. Conventional spiral-wound modules (SWMs) for desalination applications typically consist of several leaf sets, with each leaf set comprising feed spacers, membranes, and a permeate carrier (PC) wrapped around a permeate-collecting tube. The membrane area that can be packed into a given module diameter is limited by the overall leaf set thickness, restricting module productivity for a given membrane permeability. We describe here a novel industrial-scale method for successfully coating the polysulfone (PSf) ultrafiltration (UF) support layer directly onto a permeate carrier, instead of conventional non-woven fabric, as a precursor to the polyamide TFC coating, resulting in twofold benefits: (a) drastically simplifying the membrane fabrication process by eliminating the use of non-woven fabric and (b) increasing the throughput of each membrane module by facilitating the packing of a larger membrane area in a standard module housing. By combining the permeate carrier and membrane into a single sheet, the need for the non-woven support layer was eliminated, leading to a significantly reduced leaf set thickness, enabling a much larger membrane area to be packed in a given volume, leading to lower energy consumption per cubic meter of produced water. Molecular-weight cutoff (MWCO) values in the range of 36–96 kDa were found to be dependent on PC thickness and material. Nevertheless, the reinforced membranes were successfully fabricated with a ~9% reduction in membrane leaf thickness compared to a conventional membrane. Preliminary trials of coating a thin-film composite PA layer resulted in defect-free reverse osmosis (RO) membranes with a salt rejection of 94% and a flux of 40 L m⁻² h⁻¹ when tested against a 2000 mg/L NaCl feed solution at an operating pressure of 15 bar. Results from the testing of the 1812 and 2514 elements validated the novel concept and paved the way for further improvements towards full-scale RO membranes with the potential to be the next low-energy workhorse of the water industry.