Diffusion Bonding and Transient Liquid Phase (TLP) Bonding of Type 304 and 316 Austenitic Stainless Steel—A Review of Similar and Dissimilar Material Joints

Diffusion Bonding 321-Grade Stainless Steel: Failure and Multimodal Characterization

Vacuum diffusion-bonded printed circuit heat exchangers are an attractive choice for the high-temperature, high-pressure demands of next-generation energy applications. However, early reports show that the high-temperature materials desired for these applications suffer from poor bond strengths due to precipitation at the bond line, preventing grain boundary migration. In this study, a diffusion bond of the high-temperature stainless steel grade 321H is investigated, and poor mechanical properties are found to be caused by Ti(C, N) precipitation at the bond line. Through in situ studies, it is found that Ti diffuses from the bulk to the mating surfaces at high temperatures. The Ti subsequently precipitates and, for the first time, an interaction between Ti(C, N) and Al/Mg-oxide precipitates at the bond line is observed, where Ti(C, N) nucleates on the oxides forming a core-shell structure. The results indicate that small amounts of particular alloying elements can greatly impact diffusion bond quality, prompting further research into the microstructural evolution that occurs during bonding conditions.

New Inhibitor Based on Hydrolyzed Keratin Peptides for Stainless Steel Corrosion in Physiological Serum: An Electrochemical and Thermodynamic Study

Reducing the impact of some biological fluids on bioimplants involves the control of surface characteristics by modeling the interface architecture and assembling ecofriendly thin films to retard corrosion. Therefore, a mixture of hydrolyzed keratin peptides (HKER) was investigated as a corrosion inhibitor for 304L stainless steel (SS) in physiological serum (PS), using electrochemical measurements associated with optical microscopy and atomic force microscopy (AFM). The tests, performed for various concentrations of the inhibitor at different temperatures, showed that the inhibition efficiency (IE) decreased with a rise in temperature and proportionally increased with the HKER concentration, reaching its maximum level, around 88%, at 25 °C, with a concentration of 40 g L-1 HKER in physiological serum. The experimental data best fitted the El-Awady adsorption model. The activation parameters (Ea, ∆Ha and ∆Sa) and the adsorption ones (∆Gads0, ∆Hads, ∆Sads) have highlighted a mixed action mechanism of HKER, revealing that physisorption prevails over chemisorption. AFM parameters, such as the average roughness (Ra), root-mean-square roughness (Rq) and maximum peak-to-valley height (Rp-v), confirmed HKER adsorption, indicating that a smoother surface of the 304L stainless steel was obtained when immersed in a PS-containing inhibitor, compared to the surface designed in blank solution, due to the development of a protective layer on the alloy surface.

Impact of Bonding Temperature on Microstructure, Mechanical, and Fracture Behaviors of TLP Bonded Joints of Al2219 with a Cu Interlayer

The present study aims at producing transient liquid phase (TLP) bonded Al2219 joints with pure Cu (copper) as an interlayer. The TLP bonding is carried out at the bonding temperatures in the range of 480 to 520 °C while keeping the bonding pressure (2 MPa) and time (30 min.) constant. Reaction layers are formed at the Al-Cu interface with a significant increase in diffusion depth with the increase in the bonding temperature. The microstructural investigations are carried out using scanning electron microscopy and energy-dispersive spectroscopy. X-ray diffraction study confirms the formation of CuAl₂, CuAl, and Cu₉Al₄ intermetallic compounds across the interface of the bonded specimens. An increase in microhardness is observed across the bonding zone with the increase in the bonding temperature, and a maximum hardness value of 723 Hv is obtained on the diffusion zone of the specimen bonded at 520 °C. Furthermore, the fractography study of the bonded specimens is carried out, and a maximum shear strength of 18.75 MPa is observed on the joints produced at 520 °C.

The Effect of Holding Time on Dissimilar Transient Liquid-Phase-Bonded Properties of Super-Ferritic Stainless Steel 446 to Martensitic Stainless Steel 410 Using a Nickel-Based Interlayer

The dissimilar joining of martensitic and ferritic stainless steels have been developed that needs corrosion resistance and enhanced mechanical properties. In this study, the transient liquid-phase bonding of martensitic stainless steel 410 and super-ferritic stainless steel 446 was conducted with a nickel-based amorphous interlayer (BNi-2) at constant temperature (1050 °C) and increasing times of 1, 15, 30, 45, and 60 min. For characterization of the TLP-bonded samples, optical microscopy and scanning emission microscopy equipped with energy-dispersive X-ray spectroscopy were used. To investigate the mechanical properties of TLP-bonded samples, the shear strength test method was used. Finally, the X-ray diffraction method was used for microstructural investigation and phase identification. The microstructural study showed that the microstructure of base metals changed: the martensitic structure transited to tempered martensite, including ferrite + cementite colonies, and the delta phase in super-ferritic stainless steel dissolved in the matrix. During the transient liquid-phase bonding, the aggregation of boron due to its diffusion to base metals resulted in the precipitation of a secondary phase, including iron-chromium-rich borides with blocky and needle-like morphologies at the interface of the molten interlayer and base metals. On the other hand, the segregation of boron in the bonding zone resulted from a low solubility limit, and the distribution coefficient has induced some destructive and brittle phases, such as nickel-rich (Ni₃B) and chromium-rich boride (CrB/Cr₂B). By increasing the time, significant amounts of boron have been diffused to a base metal, and diffusion-induced isothermal solidification has happened, such that the isothermal solidification of the assembly has been completed under the 1050 °C/60 min condition. The distribution of the hardness profile is relatively uniform at the bonding zone after completing isothermal solidification, except the diffusion-affected zone, which has a higher hardness. The shear strength test showed that increasing the holding time was effective in achieving the strength near the base metals such that the maximum shear strength of about 472 MPa was achieved.

The Joining of Copper to Stainless Steel by Solid-State Welding Processes: A Review

Joining immiscible materials such as copper and stainless steel together is a significant concern due to distinct mechanical and metallurgical properties across the joint line, such as melting points, the coefficient of linear thermal expansion, and thermal conductivity. The joint properties of copper to stainless steel welds are in great demand for various mechanical components of the international thermonuclear experimental reactor, ultra-high vacuum system, plan wave linear-accelerator or linac structure, and heat exchanger. These dissimilar-metals joints offer excellent flexibility in design and production, leading to a robust structure for many cutting-edge applications. Hence, the present article reviews the copper to stainless steel joining mechanism under different solid-state processing conditions. The present understanding says that defect-free strong joints between the dissimilar metals are systematically possible. Apart from this understanding, the authors have identified and highlighted the gaps in the research exploration to date. Moreover, a sustainable methodology to achieve a desirable weld of copper to stainless steel depends on favorable processing conditions.

Mechanical Performance and Corrosion Behaviour of Diffusion-Bonded A5083 Aluminium and A36 Mild Steel with Gallium Interlayer

This article investigated the mechanical performance and corrosion behaviour of a diffusion-bonded A5083 aluminium/A36 mild steel dissimilar joint with a Gallium (Ga) interlayer. The bonding parameters were the bonding temperature (525 and 550 °C), holding time (60 and 120 min) and surface roughness (800 and 1200 grit). Property characterisation was achieved using Scanning Electron Microscopy (SEM), Energy Dispersive X-ray (EDX) analysis, Vickers microhardness tester, Izod impact tester and potentiodynamic polarisation testing. The results revealed that the significance of the bonding parameters was in the order bonding temperature > surface roughness > holding time. Increasing the bonding temperature resulted in an increase in the impact strength and a corresponding reduction in the corrosion rate and microhardness. However, increasing the grit size decreased the microhardness and a corresponding increase in the impact strength and corrosion rate. The impact strength and corrosion rate decreased with the increasing holding time while the microhardness followed a reverse trend. It was also discovered that incorporating the Ga interlayer resulted in a 67.9% improvement in the degradation rate.

Nondestructive Testing of Local Incomplete Brazing Defect in Stainless Steel Core Panel Using Pulsed Eddy Current

Stainless steel core panel is a novel structure for fast modular building, but its brazing foils are susceptible to defects due to the difficulty of precisely controlling the brazing process. An automated, nondestructive testing technique is highly desirable for quick inspection of the brazing defects buried in the stainless-steel core panel. In this paper, pulsed eddy current testing (PECT) was employed to inspect local incomplete brazing defects. Finite element simulation and experiment verification were conducted to investigate the feasibility and effectiveness of the proposed method. The peak value of the PECT signal was found to be sensitive to the presence of the defect. With the aid of an industrial robotic arm, line and two-dimensional scans were performed of the PECT probe above the panel specimen. The prefabricated incomplete brazing foil was successfully imaged as a notched ring, whose opening coincides with the physical length of the missing brazing. The proposed method shows potential to serve as an effective tool for in-line or off-line automated nondestructive testing of the brazing defects in stainless steel core panels.

Optimization of Vacuum Brazing Process Parameters in Ti-6Al-4V Alloy

In this study, the optimal parameters of the vacuum brazing titanium alloy Ti-6Al-4V with TiCuNi filler (30 μm-thick metal foil) were investigated by the Taguchi method. The microstructures, microhardness, and fractographs of the titanium brazed joints produced by these optimal parameters were also analyzed. The results of this study demonstrate that for the best tensile strength, the optimal combination of process parameters is: 890 °C soaking temperature, 60 min soaking time, 975 °C brazing temperature, and 45 min brazing time. The tensile strength obtained by welding with the optimal parameters was found to be 1265 MPa. A small error of 0.24% between experimental and predicted values confirmed the validity of the combined optimized parameters. Finally, from the means of variance analysis (ANOVA), out of the four factors, the highest contribution to the optimal parameters was found to be the brazing time, accounting for 47.3%. The base material of vacuum brazing (VB) weldment is mainly composed of white granular α titanium, slender β titanium, and layered structures that are interlaced by α and β. The weld bead, composed of Ti-15Cu-15Ni, contains many slender needle-shaped Widmanstätten structures. This structure is associated with higher strength and lower ductility. The weld bead hardness of the vacuum brazed parts is higher than that of laser beam weldment and gas tungsten arc weldment. This study demonstrates the feasibility of the Taguchi method for obtaining the optimal process parameters of titanium vacuum brazed joints.

Microstructure and Texture Evolution in Low Carbon and Low Alloy Steel during Warm Deformation

Warm compression tests were carried out on low carbon and low alloy steel at temperatures of 600−850 °C and stain rates of 0.01−10 s−1. The evolution of microstructure and texture was studied using a scanning electron microscope and electron backscattered diffraction. The results indicated that cementite spheroidization occurred and greatly reduced at 750 °C due to a phase transformation. Dynamic recrystallization led to a transition from {112}<110> texture to {111}<112> texture. Below 800 °C, the intensity and variation of texture with deformation temperature is more significant than that above 800 °C. The contents of the {111}<110> texture and {111}<112> texture were equivalent above 800 °C, resulting in the better uniformity of γ-fiber texture. Nucleation of <110>//ND-oriented grains increased, leading to the strengthening of <110>//ND texture. Microstructure analysis revealed that the uniform and refined grains can be obtained after deformation at 800 °C and 850 °C. The texture variation reflected the fact that 800 °C was the critical value for temperature sensitivity of warm deformation. At a large strain rate, the lowest dislocation density appeared after deformation at 800 °C. Therefore, 800 °C is a suitable temperature for the warm forming application, where the investigated material is easy to deform and evolves into a uniform and refined microstructure.

Corrosion and Microstructural Investigation on Additively Manufactured 316L Stainless Steel: Experimental and Statistical Approach

The use of metal additive manufacturing (AM) has strongly increased in the industry during the last years. More specifically, selective laser melting (SLM) is one of the most used techniques due to its numerous advantages compared to conventional processing methods. The purpose of this study is to investigate the effects of process parameters on the microstructural and corrosion properties of the additively manufactured AISI 316L stainless steel. Porosity, surface roughness, hardness, and grain size were studied for specimens produced with energy densities ranging from 51.17 to 173.91 J/mm³ that resulted from different combinations of processing parameters. Using experimental results and applying the Taguchi model, 99.38 J/mm³ was determined as the optimal energy density needed to produce samples with almost no porosity. The following analysis of variance ANOVA confirmed the scanning speed as the most influential factor in reducing the porosity percentage, which had a 74.9% contribution, followed by the position along the building direction with 22.8%, and finally, the laser energy with 2.3%. The influence on corrosion resistance was obtained by performing cyclic potentiodynamic polarization tests (CPP) in a 3.5 wt % NaCl solution at room temperature for different energy densities and positions (Z axis). The corrosion properties of the AM samples were studied and compared to those obtained from the traditionally manufactured samples. The corrosion resistance of the samples worsened with the increase in the percentage of porosity. The process parameters have consequently been optimized and the database has been extended to improve the quality of the AM-produced parts in which microstructural heterogeneities were observed along the building direction.

Chemical Cleaning of Magnetite Deposits on the Flow Mini-Channels of a Printed Circuit Heat Exchanger in an EDTA-Based Solution

The dissolution behavior of magnetite deposited on flow mini-channel surfaces within a printed circuit heat exchanger (PCHE) and the corrosion behavior of a STS 316L PCHE material were investigated in an ethylendiaminetetraacetic acid (EDTA)-based chemical cleaning solution at 93 °C. The fouling in the PCHE was simulated using a water-steam circulation loop system. Most of the magnetite deposits were rapidly dissolved in the early stage of the circulation chemical cleaning. An empirical equation for estimating the dissolution percentage was derived as a function of cleaning time. The PCHE material showed excellent corrosion resistance during the chemical cleaning tests. These results indicate the fouling layers in the PCHEs can be removed efficiently by the chemical cleaning process without concern about base metal corrosion.

Frictional Behavior and Mechanical Performance of Al Reinforced with SiC via Novel Flake Powder Metallurgy

This paper targets developing new low-cost sustainable materials. To achieve this objective, aluminum was utilized as base material for metal matrix nanocomposites (MMNC). Three routes of advanced manufacturing techniques were designed and implemented. Flake powder metallurgy as a reliable method to synthesis nanocomposites powder was employed. By reinforcing aluminium with SiC and using a similar amount of both constitutes, three metal matrix nanocomposites (MMNCs) with different properties were produced. The ball milled powder were characterized using filed emission scanning electron microscope (FE-SEM) to analyze the morphology of the powder. Different investigations and analysis were conducted on the produced samples. These include X-ray diffraction (XRD) analysis, density and porosity, mechanical properties, and frictional performance. The obtained results include relative density, Young’s modulus, compressive yield strength, elongation, toughness, hardness, coefficient of friction, and specific wear rate. Achieving superior mechanical and tribological performance is evident from these results. This is accredited to the homogeneity of the reinforcement dispersion within the aluminum matrix.

Diffusion Bonding of Al-Mg-Si Alloy and 301L Stainless Steel by Friction Stir Lap Welding Using a Zn Interlayer

Friction stir lap welding (FSLW) is expected to join the hybrid structure of aluminum alloy and steel. In this study, the Al-Mg-Si aluminum alloy and 301L stainless steel were diffusion bonded by FSLDW with the addition of 0.1 mm thick pure Zn interlayer, when the tool pin did not penetrate the upper aluminum sheet. The characteristics of lap interface and mechanical properties of the joint were analyzed. Under the addition of Zn interlayer, the diffusion layer structure at lap interface changed from continuous to uneven and segmented. The components of the diffusion layer were more complex, including Fe-Al intermetallic compounds (IMCs), Fe-Zn IMCs and Al-Zn eutectic. The largely changed composition and thickness of uneven and segmented diffusion layer at the lap interface played a significant role in the joint strength. The tensile shear load of Zn-added joint was 6.26 kN, increasing by 41.3% than that of Zn-not-added joint. These two joints exhibited interfacial shear fracture, while the Zn interlayer enhanced the strength of diffusion bonding by extending the propagation path of cracks.

Microstructure Evolution and Mechanical Properties of X6CrNiMoVNb11-2 Stainless Steel after Heat Treatment

X6CrNiMoVNb11-2 supermartensitic stainless steel, a special type of stainless steel, is commonly used in the production of gas turbine discs in liquid rocket engines and compressor disks in aero engines. By optimizing the parameters of the heat-treatment process, its mechanical properties are specially adjusted to meet the performance requirement in that particular practical application during the advanced composite casting-rolling forming process. The relationship between the microstructure and mechanical properties after quenching from 1040 °C and tempering at 300–670 °C was studied, where the yield strength, tensile strength, elongation and impact toughness under different cooling conditions are obtained by means of mechanical property tests. A certain amount of high-density nanophase precipitation is found in the martensite phase transformation through the heat treatment involved in the quenching and tempering processes, where M₂₃C₆ carbides are dispersed in lamellar martensite, with the close-packed Ni₃Mo and Ni₃Nb phases of high-density co-lattice nanocrystalline precipitation created during the tempering process. The ideal process parameters are to quench at 1040 °C in an oil-cooling medium and to temper at 650 °C by air-cooling; final hardness is averaged about 313 HV, with an elongation of 17.9%, the cross-area reduction ratio is 52%, and the impact toughness is about 65 J, respectively. Moreover, the tempered hardness equation, considering various tempering temperatures, is precisely fitted. This investigation helps us to better understand the strengthening mechanism and performance controlling scheme of martensite stainless steel during the cast-rolling forming process in future applications.

Brazing Tungsten/Tantalum/RAFM Steel Joint for DEMO by Fully Reduced Activation Brazing Alloy 48Ti-48Zr-4Be

To create a DEMO reactor, it is necessary to develop high-quality technology to join tungsten with reduced-activation ferritic-martensitic (RAFM) steel (Rusfer, Eurofer, CLF-1, etc.). Difficulties arise in their direct connection due to the large difference in the coefficient of thermal expansion (CTE). To suppress the difference of CTE, intermediate interlayers are usually used, such as vanadium or tantalum, and brazing is a prospective technology to conduct the joining. The vast majority of works represent copper- or nickel-based brazing alloys, but their applicability is under significant discussion due to their activation properties. That is why, in this work, fully reduced activation 48Ti-48Zr-4Be wt.% brazing alloy was used. The following joint was made: Rusfer steel/48Ti-48Zr-4Be/Ta/48Ti-48Zr-4Be/W. The brazing was successfully carried out under a mode providing thermal heat treatment of Rusfer. Through EDS and EBSD analysis, the microstructure of the joint was determined. Shear strength of the as-joined composition was measured as 127 ± 20 MPa. The joint endured 200 thermocycles in the temperature range between 300–600 °C, but the fillet regions degraded.

Microstructure and Properties of SUS304 Stainless Steel Joints Brazed with Electrodeposited Ni-Cr-P Alloy Coatings

In this study, an amorphous Ni-13.4Cr-11.6P (mass%) alloy coating with a thickness of 30 μm was deposited on the surface of SUS304 stainless steel as a brazing filler metal to conduct brazing. The differential thermal analysis measurements indicate that the electrodeposited Ni-13.4Cr-11.6P alloy has a melting point of approximately 892 °C, which is almost consistent with that of the commercial BNi-7 filler metal. The microstructure, shear strength, and fracture mode of the brazed joint were investigated using an electron probe X-ray microanalyzer, a scanning electron microscope, an optical microscope, and a universal testing machine. The results showed that the brazed filler metal is filled between the SUS304 stainless steel plates without any flaws in the brazed seam. The P-containing phases, i.e., the Cr-P rich phase and the (Ni,Fe)₃P phase, were formed in the brazed seam. The shear strength of the brazed joint obtained in this study is 59.0 MPa. The fracture occurs in the brazed filler zone, where the brittle P-containing phases are present. Galvanic current measurement results showed that the brazed Ni-13.4Cr-11.6P alloy coating has a better corrosion resistance than that of the brazed Ni-11P alloy coating, which can be attributed to the formation of a large amount of Ni-Fe solid solution and Cr-P rich phase in the top layer of the brazed Ni-13.4Cr-11.6P alloy coating.

Microstructure and Anisotropy of the Mechanical Properties of 316L Stainless Steel Fabricated by Selective Laser Melting

Significant anisotropy in mechanical properties was observed in 316L stainless steel (SS) that was subjected to selective laser melting (SLM) to produce a hierarchical structure, composed of molten pool, columnar grains, and a cellular substructure. Such anisotropy was induced by the geometric relationship between the boundary of the molten pool and the tensile force. The in situ tensile test showed initial deformation rapidly occurred at the boundary of the molten pool, followed by strain localization, and a lower ductility was obtained when loaded in the longitudinal direction (perpendicular to the molten pool). By contrast, the deformation was significantly constrained because of the geometry of the boundary of the molten pool, and substantial deformation occurred in the cellular substructure during loading in transverse direction (parallel to the molten pool). Finally, the quantitative analysis revealed that the high-level strength was attributed to the high-density dislocations and the fine cellular substructure.

Microstructural Investigation of a Friction-Welded 316L Stainless Steel with Ultrafine-Grained Structure Obtained by Hydrostatic Extrusion

The paper presents the microstructural investigation of a friction-welded joint made of 316L stainless steel with an ultrafine-grained structure obtained by hydrostatic extrusion (HE). Such a plastically deformed material is characterized by a metastable state of energy equilibrium, increasing, among others, its sensitivity to high temperatures. This feature makes it difficult to weld ultra-fine-grained metals without losing their high mechanical properties. The use of high-speed friction welding and a friction time of <1 s reduced the scale of the weakening of the friction joint in relation to result obtained in conventional rotary friction welding. The study of changes in the microstructure of individual zones of the friction joint was carried out on an optical microscope (OM), scanning electron microscope (SEM), transmission electron microscope (TEM) and electron backscattered diffraction (EBSD) analysis system. The correlation between the microstructure and hardness of the friction joint is also presented. The heat released during the high-speed friction welding initiated the process of dynamic recrystallization (DRX) of single grains in the heat-affected zone (HAZ). The additional occurrence of strong plastic deformations (in HAZ) during flash formation and internal friction (in the friction weld and high-temperature HAZ) contributed to the formation of a highly deformed microstructure with numerous sub-grains. The zones with a microstructure other than the base material were characterized by lower hardness. Due to the complexity of the microstructure and its multifactorial impact on the properties of the friction-welded joint, strength should be the criterion for assessing the properties of the joint.

Impulse Pressure-Assisted Diffusion Bonding (IPADB): Review and Outlook

Diffusion bonding is a solid-state welding technique used to join similar and dissimilar materials. Relatively long processing times, usually in the order of several hours as well as fine polished surfaces make it challenging to integrate diffusion bonding in other production processes and mitigate widespread use of the technology. Several studies indicate that varying pressure during diffusion bonding in contrast to the traditionally applied constant load may reduce overall processing- and bonding times. Such processes are referred to as impulse pressure-assisted diffusion bonding (IPADB) and they are, for the first time, reviewed in this work using the PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analysis) methodology. Results of the review indicate that varying pressure can indeed reduce bonding times in diffusion bonding and reduce the requirements for pre-bond surface preparation. Additional research is required and should go beyond small and simple sample geometries to concentrate on making IPADB accessible to industrial applications.