Resin-Based Sealant with Bioactive Glass and Zwitterionic Material for Remineralisation and Multi-Species Biofilm Inhibition

Effects of different removal methods of excess resin adhesive on the microleakage of alumina all-ceramic crowns

BACKGROUND

Microleakage is a common problem that affects the quality and longevity of all-ceramic crowns. It is influenced by factors such as the resin cement, crown margin design and curing technique. However, few studies focus on the effect of different methods of removing excess resin adhesive on the microleakage of all-ceramic crowns. This study aimed to compare two methods of removing excess resin adhesive (the small brush and sickle methods) on the microleakage of all-ceramic crowns with different marginal clearances.

METHODS

Forty extracted third molars were prepared with a 90° shoulder margin and randomly divided into four groups according to their marginal lift (30, 60, 90 or 0 μm). Procera alumina crowns were fabricated using computer-aided design/computer-aided modelling and cemented onto the teeth with 3 M RelyX Unicem (3 M Company, United States) resin cement. Excess resin cement was removed by either the small brush or the sickle scalpel method. The marginal adaptation was observed with a digital microscope. After thermal cycling of the teeth, microleakage was assessed using the dye penetration test under a stereomicroscope. The Mann-Whitney U test and Kruskal-Wallis H test were used to compare the microleakage scores among different groups.

RESULTS

The small-brush group showed significantly better marginal adaptation and lower microleakage scores than the sickle group (p < 0.05). There was no significant difference in the microleakage score (grade 0) among different marginal clearances within each group (p > 0.05).

CONCLUSION

The small-brush method was more effective than the sickle scalpel method in reducing the microleakage of all-ceramic crowns with different marginal clearances. This method can improve the marginal adaptation and sealability of all-ceramic crowns, thus preventing secondary caries and other complications.

Developing Bioactive Dental Resins for Restorative Dentistry

Despite its reputation as the most widely used restorative dental material currently, resin-based materials have acknowledged shortcomings. As most systematic survival studies of resin composites and dental adhesives indicate, secondary caries is the foremost reason for resin-based restoration failure and life span reduction. In subjects with high caries risk, the microbial community dominated by acidogenic and acid-tolerant bacteria triggers acid-induced deterioration of the bonding interface and/or bulk material and mineral loss around the restorations. In addition, resin-based materials undergo biodegradation in the oral cavity. As a result, the past decades have seen exponential growth in developing restorative dental materials for antimicrobial applications addressing secondary caries prevention and progression. Currently, the main challenge of bioactive resin development is the identification of efficient and safe anticaries agents that are detrimental free to final material properties and show satisfactory long-term performance and favorable clinical translation. This review centers on the continuous efforts to formulate novel bioactive resins employing 1 or multiple agents to enhance the antibiofilm efficacy or achieve multiple functionalities, such as remineralization and antimicrobial activity antidegradation. We present a comprehensive synthesis of the constraints and challenges encountered in the formulation process, the clinical performance-related prerequisites, the materials' intended applicability, and the current advancements in clinical implementation. Moreover, we identify crucial vulnerabilities that arise during the development of dental materials, including particle aggregation, alterations in color, susceptibility to hydrolysis, and loss of physicomechanical core properties of the targeted materials.

Water-Induced Changes in Experimental Resin Composites Functionalized with Conventional (45S5) and Customized Bioactive Glass

The aim of the study was to evaluate microhardness, mass changes during 1-year water immersion, water sorption/solubility, and calcium phosphate precipitation of experimental composites functionalized with 5-40 wt% of two types of bioactive glass (BG): 45S5 or a customized low-sodium fluoride-containing formulation. Vickers microhardness was evaluated after simulated aging (water storage and thermocycling), water sorption and solubility were tested according to ISO 4049, and calcium phosphate precipitation was studied by scanning electron microscopy, energy dispersive X-ray spectroscopy, and Fourier-transform infrared spectroscopy. For the composites containing BG 45S5, a significant reduction in microhardness was observed with increasing BG amount. In contrast, 5 wt% of the customized BG resulted in statistically similar microhardness to the control material, while higher BG amounts (20 and 40 wt%) resulted in a significant improvement in microhardness. Water sorption was more pronounced for composites containing BG 45S5, increasing 7-fold compared to the control material, while the corresponding increase for the customized BG was only 2-fold. Solubility increased with higher amounts of BG, with an abrupt increase at 20 and 40 wt% of BG 45S5. Calcium phosphate was precipitated by all composites with BG amounts of 10 wt% or more. The improved properties of the composites functionalized with the customized BG indicate better mechanical, chemical, and dimensional stability without compromising the potential for calcium phosphate precipitation.

Effect of bacterial resistant zwitterionic derivative incorporation on the physical properties of resin-modified glass ionomer luting cement

Biofilms induce microbial-mediated surface roughening and deterioration of cement. In this study, zwitterionic derivatives (ZD) of sulfobetaine methacrylate (SBMA) and 2-methacryloyloxyethyl phosphorylcholine, were added in concentrations of 0, 1, and 3% to three different types of commercially available resin-modified glass ionomer cement (RMGIC) (RMC-I: RelyX Luting 2, RMC-II: Nexus RMGI, and RMC-III: GC FujiCEM 2). The unmodified RMGICs served as the control group for comparison. The resistance of Streptococcus mutans to ZD-modified RMGIC was evaluated with a monoculture biofilm assay. The following physical properties of the ZD-modified RMGIC were assessed: wettability, film thickness, flexural strength, elastic modulus, shear bond strength, and failure mode. The ZD-modified RMGIC significantly inhibited biofilm formation, with at least a 30% reduction compared to the control group. The addition of ZD improved the wettability of RMGIC; however, only 3% of the SBMA group was statistically different (P < 0.05). The film thickness increased in proportion to the increasing ZD concentrations; there was no statistical difference within the RMC-I (P > 0.05). The experimental groups' flexural strength, elastic modulus, and shear bond strength showed an insignificant decrease from the control group; there was no statistical difference within the RMC-I (P > 0.05). The mode of failure differed slightly in each group, but all groups showed dominance in the adhesive and mixed failure. Thus, the addition of 1 wt.% ZD in RMGIC favorably enhanced the resistance to Streptococcus mutans without any tangible loss in flexural and shear bond strength.

Accuracy and stability of computer-aided customized lingual fixed retainer: a pilot study

BACKGROUND

With advances in digital technology, new types of lingual fixed retainers are being developed. However, there are few studies that quantitatively evaluate the accuracy and stability of lingual fixed retainers. The aim of this study was to assess the accuracy and stability of two types of computer-aided customized lingual fixed retainers and a conventional lingual fixed retainer.

METHODS

A total of 10 maxillary and 10 mandibular duplicated dental models were selected, and then, three types of retainers were fabricated on the canine-to-canine area for each model. To evaluate accuracy, wire clearance at interproximal area (WCI) was measured using superimposition analysis. Initial flatness deformation was also measured for vertical distortion of retainers. Lateral width, anteroposterior length, and flatness deformation were measured at three-time points for stability assessment. Thermocycling was used to induce 6 months of time flow.

RESULTS

The custom-bent group showed significantly higher WCI than the custom-cut and manual groups in the maxillary arch (P = 0.002). The custom-cut group showed significantly less flatness deformation, which was followed by the custom-bent and manual groups in both the maxillary and mandibular arch (P < 0.001). There was no significant difference in stability between the three retainer groups during 5100 cycles of thermocycling (corresponding to 6-month period).

CONCLUSIONS

Since there was no difference in stability between the three groups, it is recommended to use custom-cut type retainers in light of accuracy. However, accuracy and stability are not the only factors to consider when selecting type of retainers. Because each retainer has advantages and disadvantages, the type of retainers should be decided in consideration of the clinical environment.

Assessment of Zinc-Bound Phosphate-Based Glass-Coated Denture-Relining Material with Antifungal Efficacy for Inhibiting Denture Stomatitis

This study investigated the surface properties, biocompatibility, and antifungal activity against Candida albicans of a denture-relining material coated with zinc-bound phosphate-based glass. First, zinc-bound phosphate-based glass was fabricated. A polymerized denture-relining disk was coated with zinc-bound phosphate-based glass (2%, 4%, and 6%). The surface properties of the control and experimental groups were measured, including the wettability, microhardness, color difference, and gloss. The biocompatibility was evaluated using the MTT assay according to ISO 10993-5. The antifungal activity was investigated by counting the number of colony-forming units of Candida albicans. The results were analyzed using a one-way ANOVA and Tukey's test (p = 0.05). The results of this study indicate that, despite the antimicrobial effect of zinc-bound phosphate-based glass, a coated denture-relining material does not degrade the surface properties and biocompatibility. Therefore, this novel material is considered promising for use as a dental material with antimicrobial properties that can potentially prevent denture stomatitis.

Molecular weight tuning optimizes poly(2-methoxyethyl acrylate) dispersion to enhance the aging resistance and anti-fouling behavior of denture base resin

Poly(methyl methacrylate) (PMMA)-based denture base resins easily develop oral bacterial and fungal biofilms, which may constitute a significant health risk. Conventional bacterial-resistant additives and coatings often cause undesirable changes in the resin. Reduced bacterial resistance over time in the harsh oral environment is a major challenge in resin development. Poly(2-methoxyethyl acrylate) (PMEA) has anti-fouling properties; however, due to the oily/rubbery state of this polymer, and its surface aggregation tendency in a resin mixture, its direct use as a resin additive is limited. This study aimed to optimize the use of PMEA in dental resins. Acrylic resins containing a series of PMEA polymers with various molecular weights (MWs) at different concentrations were prepared, and the mechanical properties, surface gloss, direct transmittance, and cytotoxicity were evaluated, along with the distribution of PMEA in the resin. Resins with low-MW PMEA (2000 g mol^-1) (PMEA-1) at low concentrations satisfied the clinical requirements for denture resins, and the PMEA was homogeneously distributed. The anti-fouling performance of the resin was evaluated for protein adsorption, bacterial and fungal attachment, and saliva-derived biofilm formation. The PMEA-1 resin most effectively inhibited biofilm formation (∼50% reduction in biofilm mass and thickness compared to those of the control). Post-aged resins maintained their mechanical properties and anti-fouling activity, and polished surfaces had the same anti-biofilm behavior. Based on wettability and tribological results, we propose that the PMEA additive creates a non-stick surface to inhibit biofilm formation. This study demonstrated that PMEA additives can provide a stable and biocompatible anti-fouling surface, without sacrificing the mechanical properties and aesthetics of denture resins.

Microtensile Bond Strength of Bioactive Pit and Fissure Sealants Bonded to Primary and Permanent Teeth

Background: Sealing occlusal pits and fissures is an effective preventive measure against dental caries. Pit and fissure sealants (PFS) should be strongly bonded to the teeth to prevent partial or complete loss of the sealant, which may limit its preventive effect. Objective: The objective of the study was to compare the microtensile bond strength (μTBS) of bioactive resin-based sealants (Bio-RBS) and resin-based sealants (RBS), with and without the use of a bonding agent, to the enamel of primary and permanent teeth. Methods: One hundred and twenty caries-free primary molar specimens and 120 permanent molar specimens were divided to eight groups (30 specimens per group), both primary and permanent teeth were sealed with a Bio-RBS BioCoat^TM (Premier^®, Plymouth Meeting, PA, USA) or with a RBS Clinpro^TM (3M ESPE, Saint Paul, MN, USA), with or without the use of a bonding agent (Prime & Bond NT; Dentsply, Inc., Charlotte, NC, USA). Half the specimens were aged with 5000 thermal cycles, and all specimens were tested for the μTBS and failure mode. Results: The mean μTBS of aged Bio-RBS was higher in permanent teeth than primary teeth, and the aging process reduced the μTBS of RBS more than that of Bio-RBS. Moreover, the addition of a bonding agent improved the μTBS of aged RBS in permanent teeth. Conclusion: We concluded that Bio-RBS exhibit superior μTBS than RBS when applied to permanent teeth.

Strategies toward development of antimicrobial biomaterials for dental healthcare applications

Several approaches for elimination of oral pathogens are being explored at the present time since oral diseases remain prevalent affecting approximately 3.5 billion people worldwide. Need for antimicrobial biomaterials in dental healthcare include but is not restricted to designing resin composites and adhesives for prevention of dental caries. Constant efforts are also being made to develop antimicrobial strategies for clearance of endodontic space prior root canal treatment and for treatment of periimplantitis and periodontitis. This article discusses various conventional and nanotechnology-based strategies to achieve antimicrobial efficacy in dental biomaterials. Recent developments in the design and synthesis of antimicrobial peptides and antifouling zwitterionic polymers to effectively lessen the risks of antimicrobial drug resistance are also outlined in this review. Further, the role of contemporary strategies such as use of smart biomaterials, ionic solvent-based biomaterials and quorum quenchers incorporated biomaterials in the elimination of dental pathogens are described in detail. Lastly, we mentioned the approach of using polymers to print custom-made three-dimensional antibacterial dental products via additive manufacturing technologies. This review provides a critical perspective on the chemical, biomimetic, and engineering strategies intended for developing antimicrobial biomaterials that have the potential to substantially improve the dental health.

A modified TEGDMA-based resin infiltrant using polyurethane acrylate oligomer and remineralising nano-fillers with improved physical properties and remineralisation potential

OBJECTIVES

This study aimed to modify an experimental triethylene glycol dimethacrylate (TEGDMA) based resin infiltrant using PUA oligomer and two remineralising fillers, including fluorohydroxyapatite (FHA) and fluoride-doped bioactive glass (FD-BG), to improve the mechanical and physical properties and induce remineralising potential.

MATERIALS AND METHODS

The polyurethane acrylate oligomer (PUA) was synthesised and characterised. Experimental resin infiltrant was prepared by mixing 10% of synthesised PUA with 88% TEGDMA. Water contact angle, penetration coefficient, and penetration depth were then measured. The FHA and FD-BG fillers were synthesised and characterised. To prepare nano-filled resin infiltrant, 5% of each powder was mixed with the prepared resin infiltrant. The prepared resin infiltrants were characterised to evaluate their degree of conversion, mechanical properties, water sorption, and solubility. The ion release of filled resin was also assessed. The non-infiltrated and infiltrated enamel specimens underwent fourteen days of pH-cycling, and a surface microhardness was done to assess the resistance to demineralisation.

RESULTS

The results showed that the addition of PUA to TEGDMA increased the mechanical properties and decreased water sorption and solubility. The addition of synthesised FD-BG fillers to resin infiltrant significantly improved the resistance to demineralisation of enamel samples compared with other groups (p ≤ 0.001). The FHA fillers also improved the resistance to demineralisation; however, the produced changes were not statistically meaningful (p > 0.05).

CONCLUSIONS

Based on the results, the PUA+TEGDMA+ FD-BG/FHA composite can be used as an alternative material for pure TEGDMA in enamel infiltration approaches owing to its better mechanical properties, lower water sorption and solubility, and also remineralisation potential.

CLINICAL SIGNIFICANCE

A resin infiltrant with remineralisation potential, lower water sorption and solubility and higher mechanical properties may enhance the management of early caries lesions.

The Antibacterial Effects of Resin-Based Dental Sealants: A Systematic Review of In Vitro Studies

This review aimed to assess the antimicrobial effects of different antibacterial agents/compounds incorporated in resin-based dental sealants. Four databases (PubMed, MEDLINE, Web of Science and Scopus) were searched. From the 8052 records retrieved, 275 records were considered eligible for full-text screening. Nineteen studies met the inclusion criteria. Data extraction and quality assessment was performed by two independent reviewers. Six of the nineteen included studies were judged to have low risk of bias, and the rest had medium risk of bias. Compounds and particles such as zinc, tin, Selenium, chitosan, chlorhexidine, fluoride and methyl methacrylate were found to be effective in reducing the colony-forming unit counts, producing inhibition zones, reducing the optical density, reducing the metabolic activities, reducing the lactic acid and polysaccharide production and neutralizing the pH when they are added to the resin-based dental sealants. In addition, some studies showed that the antibacterial effect was not significantly different after 2 weeks, 2 months and 6 months aging in distilled water or phosphate-buffered saline. In conclusion, studies have confirmed the effectiveness of adding antibacterial agents/compounds to dental sealants. However, we should consider that these results are based on laboratory studies with a high degree of heterogeneity.

Bio-Interactive Zwitterionic Dental Biomaterials for Improving Biofilm Resistance: Characteristics and Applications

Biofilms are formed on surfaces inside the oral cavity covered by the acquired pellicle and develop into a complex, dynamic, microbial environment. Oral biofilm is a causative factor of dental and periodontal diseases. Accordingly, novel materials that can resist biofilm formation have attracted significant attention. Zwitterionic polymers (ZPs) have unique features that resist protein adhesion and prevent biofilm formation while maintaining biocompatibility. Recent literature has reflected a rapid increase in the application of ZPs as coatings and additives with promising outcomes. In this review, we briefly introduce ZPs and their mechanism of antifouling action, properties of human oral biofilms, and present trends in anti-biofouling, zwitterionic, dental materials. Furthermore, we highlight the existing challenges in the standardization of biofilm research and the future of antifouling, zwitterated, dental materials.

Development of a Bioactive Flowable Resin Composite Containing a Zinc-Doped Phosphate-Based Glass

Flowable resins used for dental restoration are subject to biofilm formation. Zinc has antibacterial properties. Thus, we prepared a zinc-doped phosphate-based glass (Zn-PBG) to dope a flowable resin and evaluated the antibacterial activity of the composite against Streptococcus mutans (S. mutans) to extrapolate the preventative effect toward secondary caries. The composites were prepared having 0 (control), 1.9, 3.8, and 5.4 wt.% Zn-PBG. The flexural strength, elastic modulus, microhardness, depth of cure, ion release, inhibition zone size, and number of colony-forming units were evaluated and analyzed using ANOVA. The flexural strength of the control was significantly higher than those of Zn-PBG samples (p < 0.05). However, all samples meet the International Standard, ISO 4049. The microhardness was not significantly different for the control group and 1.9 and 3.8 wt.% groups, but the 5.4 wt.% Zn-PBG group had a significantly lower microhardness (p < 0.05). Further, the composite resins increasingly released P, Ca, Na, and Zn ions with an increase in Zn-PBG content (p < 0.05). The colony-forming unit count revealed a significant reduction in S. mutans viability (p < 0.05) with increase in Zn-PBG content. Therefore, the addition of Zn-PBG to flowable composite resins enhances antibacterial activity and could aid the prevention of secondary caries.