Activated Carbon Microsphere from Sodium Lignosulfonate for Cr(VI) Adsorption Evaluation in Wastewater Treatment

Preparation, characterization, and adsorption performance of porous polyamine lignin microsphere

In this study, a porous polyamine lignin microsphere (PPALM) was prepared through the inverse suspension polymerization combined with freeze-drying, during which sodium lignosulfonate and polyetheramine (PEA) were crosslinked with epichlorohydrin (ECH) as the cross-linker. By adjusting the amount of ECH and PEA, the optimized PPALM exhibited suitable crosslinking degree, ensuring a balance of framework flexibility and rigidity, thereby facilitating the formation of abundant and fine pores. PPALM demonstrated good mechanical properties comparable to commercial sulfonated polystyrene cationic resin, with a porosity of 61.12 % and an average pore size of 283.51 nm. The saturation adsorption capacity of PPALM for Pb2+ was measured to be 156.82 mg/g, and it remained above 120 mg/g after five cycles of regeneration. Particularly, the concentration of 50 mg/L Pb2+ solution could be reduced to 0.98 mg/L after flowing through the PPALM packed bed, indicating the great potential of PPALM for application in wastewater treatment.

Enhancement of Cr(VI) adsorption on lignin-based carbon materials by a two-step hydrothermal strategy: Performance and mechanism

Cr(VI) is a carcinogenic heavy metal that forms an oxygen-containing anion, which is difficult to remove from water by adsorbents. Here, industrial alkali lignin was transformed into a Cr(VI) adsorbent (N-LC) by using a two-step hydrothermal strategy. The characterization results of the adsorbent showed that O and N were uniformly distributed on the surface of the adsorbent, resulting in a favorable morphology and structure. The Cr(VI) adsorption of N-LC was 13.50 times that of alkali lignin, and the maximum was 326.10 mg g-1, which confirmed the superiority of the two-step hydrothermal strategy. After 7 cycles, the adsorption of N-LC stabilized at approximately 62.18 %. In addition, in the presence of coexisting ions, N-LC showed a selective adsorption efficiency of 85.47 % for Cr(VI), which is sufficient to support its application to actual wastewaters. Model calculations and characterization showed that N and O groups were the main active factors in N-LC, and CO, -OH and pyridinic-N were the main active sites. This study provides a simple and efficient method for the treatment of heavy metals and the utilization of waste lignin, which is expected to be widely applied in the environmental, energy and chemical industries.

Efficient removal of both heavy metal ion and dyes from wastewater using magnetic response adsorbent of block polymer brush-grafted N-doped biochar

The recovery of biomass from agricultural and forestry waste could realize effective utilization of waste and synthesis of novel adsorbent. Herein, porous biochar was prepared from waste ginkgo biloba leaves and modified by Reversible Addition-Fragmentation Chain Transfer Polymerization (RAFT). And the prepared adsorbent exhibited excellent adsorption capacity owing to its abundant functional groups and porous structure. In addition, the adsorption capacities of the prepared adsorbent for Malachite Green (MG), Amaranth (AM) and Cr (Ⅵ) were 422.59, 373.75 and 368.82 mg/g, respectively, surpassing those of many previously reported materials. Subsequently, the influence of various factors on adsorption performance was studied. The results showed that adsorption of MG, AM and Cr (Ⅵ) on adsorbent followed pseudo-second-order and Langmuir models and the adsorbent also displayed excellent cycling performance. The experimental results of application in various water samples showed that the adsorbent had outstanding adsorption performance in real water samples, further proving that the adsorbent had wide application and practicability. Finally, a simple adsorption column was used for filtration experiments to simulate industrial application. The results were exhibited that the adsorbent had great potential in treating wastewater containing MG, AM and Cr (Ⅵ).

Amination-modified lignin recovery of aqueous phosphate for use as binary slow-release fertilizer

To address the global phosphorus crisis and solve the problem of eutrophication in water bodies, the recovery of phosphate from wastewater for use as a slow-release fertilizer and to improve the slow-release performance of fertilizers is considered an effective way. In this study, amine-modified lignin (AL) was prepared from industrial alkali lignin (L) for phosphate recovery from water bodies, and then the recovered phosphorus-rich aminated lignin (AL-P) was used as a slow-release N and P fertilizer. Batch adsorption experiments showed that the adsorption process was consistent with the Pseudo-second-order kinetics and Langmuir model. In addition, ion competition and actual aqueous adsorption experiments showed that AL had good adsorption selectivity and removal capacity. The adsorption mechanism included electrostatic adsorption, ionic ligand exchange and cross-linked addition reaction. In the aqueous release experiments, the rate of nitrogen release was constant and the release of phosphorus followed a Fickian diffusion mechanism. Soil column leaching experiments showed that the release of N and P from AL-P in soil followed the Fickian diffusion mechanism. Therefore, AL recovery of aqueous phosphate for use as a binary slow-release fertilizer has great potential to improve the environment of water bodies, enhance nutrient utilization and address the global phosphorus crisis.

Removal of Chromium Species by Adsorption: Fundamental Principles, Newly Developed Adsorbents and Future Perspectives

Emerging chromium (Cr) species have attracted increasing concern. A majority of Cr species, especially hexavalent chromium (Cr(VI)), could lead to lethal effects on human beings, animals, and aquatic lives even at low concentrations. One of the conventional water-treatment methodologies, adsorption, could remove these toxic Cr species efficiently. Additionally, adsorption possesses many advantages, such as being cost-saving, easy to implement, highly efficient and facile to design. Previous research has shown that the application of different adsorbents, such as carbon nanotubes (carbon nanotubes (CNTs) and graphene oxide (GO) and its derivatives), activated carbons (ACs), biochars (BCs), metal-based composites, polymers and others, is being used for Cr species removal from contaminated water and wastewater. The research progress and application of adsorption for Cr removal in recent years are reviewed, the mechanisms of adsorption are also discussed and the development trend of Cr treatment by adsorption is proposed.

Facile synthesis of sodium lignosulfonate/polyethyleneimine/sodium alginate beads with ultra-high adsorption capacity for Cr(VI) removal from water

Chromium (VI) is a widely occurring toxic heavy metal ion in industrial wastewater that seriously impacts the environment. In this study, we used environmentally friendly sodium lignosulfonate (SL), polyethyleneimine (PEI), and sodium alginate (SA) to synthesize SL/PEI/SA beads by employing a simple crosslinking method with to develop a novel absorbent with excellent adsorption capacity and practical application in wastewater treatment. We studied the adsorption performance of SL/PEI/SA through batch adsorption and continuous dynamic adsorption experiments. SL/PEI/SA has ultra-high adsorption capacity (2500 mg·g^-1) at 25 ℃, which is much higher than that of existing adsorbents. Humic acids and coexisting anions commonly found in wastewater have minimal effect on the adsorption performance of SL/PEI/SA. In the column system, 1 g SL/PEI/SA can treat 8.1 L secondary electroplating wastewater at a flow rate of 0.5 mLmin^-1, thereby enabling the concentration of Cr(VI) in secondary electroplating wastewater to meet the discharge standard (< 0.2 mg·L^-1). It is worth noting that the concentration of competitive ions in secondary electroplating wastewater is more than 500 times higher than that of Cr(VI). These results demonstrate that the novel SL/PEI/SA beads can be effectively applied in the removal of Cr(VI) in wastewater.

Wastewater Treatment by Polymeric Microspheres: A Review

This review addresses polymer microspheres used as adsorbent for wastewater treatment. The removal of various pollutants (including dyes, heavy metal ions, and organic pollutants) is a prominent issue, as they can cause severe health problems. Porous microspheres can provide large specific area and active sites for adsorption or photo degradation. Enhancement in performance is achieved by various modifications, such as the introduction of nanoparticles, magnetic particles, and ZIF-8. Some microspheres were synthesized from synthetic polymers such as vinylic polymer and polydopamine (PDA) through a facile fabrication process. Natural polymers (such as cellulose, alginate, and chitosan) that are biodegradable and eco-friendly are also used. The adsorbents used in industrial application require high adsorption capacity, thermal stability, and recyclability. Batch adsorption experiments were conducted to investigate the optimal conditions, influence of related factors, and adsorption capacities. Insights regarding the adsorption mechanisms were given from the kinetic model, isotherm model, and various characterization methods. The recyclability is investigated through regeneration ratio, or their maintenance of their capability through repeated adsorption-desorption cycles. The high potential of polymer microsphere for the removal of pollutants from wastewater is shown through the high adsorption capacities, environmentally friendliness, and high stability.

A novel lignin-based hierarchical porous carbon for efficient and selective removal of Cr(VI) from wastewater

A novel lignin-based hierarchical porous carbon (L-HPC) was prepared to remove Cr(VI) from water by using industrial alkali lignin through simple hydrothermal-induced assembly and alkali activation strategy. The adsorbent were characterized by SEM-EDS mapping, TEM, BET, XPS, FTIR, Raman spectroscopy and zeta potential. The characterization results indicated that L-HPC contained three-dimensional connected channels and many adsorbing N, O and other adsorption groups, which is very beneficial for Cr(VI) adsorption. The kinetics showed that the L-HPC adsorption of Cr(VI) was chemical adsorption and mainly controlled by intraparticle diffusion. The isotherm and thermodynamics indicated that L-HPC adsorption of Cr(VI) conforms to the Freundlich model, L-HPC is a kind of multimolecular layer adsorbent, and the adsorption capacity of Cr(VI) by L-HPC was 887.8 mg/g, which was significantly higher than values for other adsorbents. Ion competition simulation and actual water body tests showed that L-HPC exhibits high selectivity for Cr(VI) adsorption, adsorption cycle experiments show that L-HPC maintains over 83% performance after 12 cycles. Cost analysis shows that L-HPC is suitable for mass production. Therefore, L-HPC is a Cr(VI) adsorbent with high efficiency, high selectivity, and high reusability, which is broadly applicable and shows favorable prospects.

Application of Amberlite IRA 402 Resin Adsorption and Laccase Treatment for Acid Blue 113 Removal from Aqueous Media

Despite Acid Blue 113 (AB 113)'s extensive use and negative environmental impact, very few studies have focused on its efficient and environmentally friendly removal. This research aims the removal of AB 113 from environmental aqueous media and its consequent enzymatic biodegradation. A strongly basic anion exchange resin in Cl^- form, Amberlite IRA 402 (IRA 402(Cl^-)) was used for AB 113 adsorption and a laccase was used to further biodegrade it. For the first time, two novel, efficient and environmentally friendly physical-chemical and biological assays for AB 113 wastewater removal and subsequent biodegradation were combined. The adsorption of AB 113 onto IRA 402(Cl^-) was tested in batch and continuous flux modes. Influence of contact time, concentration and desorption in acidic media were evaluated. The kinetic data were best modulated by the Lagergren model with R² = 0.9275. The Langmuir isotherm model best fitted the experimental data, and the maximum adsorption capacity was 130 mg/g. Dye, resin and AB113 loaded resin were characterized by thermogravimetry and FTIR to evaluate their physical chemical properties modification. Based on the performed studies, a consecutive methodology is proposed, incorporating the ion exchange process in the first stage and the biodegradation process in the second. Thus, in the second stage the residual concentration of AB 113 is reduced by an efficient bio-degradation process produced by the laccase at pH = 4.

Fabrication of Superamphiphilic Carbon Using Lignosulfonate for Enhancing Selective Hydrogenation Reactions in Pickering Emulsions

Superamphiphilic materials have great potential to enhance the mass transfer between phases in liquid-liquid catalysis due to their special affinities. Constructing superamphiphilic surfaces that possess superhydrophilic and superhydrophobic properties simultaneously has been a tough assignment. So, exploration of simple methods to prepare such materials using renewable and abundant feedstocks is highly desired. Here, we reported an effective strategy to construct superamphiphilic carbon directly from sodium lignosulfonate, which is a renewable resource from paper industry wastes. From the characterization of X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) for superamphiphilic carbon, we found that element C was responsible for the hydrophobic nature and the existence of O and S endowed the carbon with hydrophilic characteristics. Further, micro/nanohierarchical pores were found beneficial for the superamphiphilicity of carbon. Meantime, in the selective hydrogenation of styrene, phenylacetylene, and cis-stilbene in liquid-liquid systems, conversion became double using superamphiphilic carbon compared with blank results, and the yields were three times more than those in blank experiments. The reasons were that superamphiphilic carbon induced the formation of Pickering emulsions and enriched the reactants around catalysts, as concluded by the characterization of confocal laser scanning microscopy and relating contrastive experiments. This work revealed a different route to obtain superamphiphilic carbon and provided a diverse perspective to promote Pickering emulsion catalysis by the superamphiphilicity of carbon.

Preparation of a Novel Polystyrene-Poly(hydroxamic Acid) Copolymer and Its Adsorption Properties for Rare Earth Metal Ions

In this study, a novel polystyrene-poly(hydroxamic acid) copolymer was synthesized as an effective adsorbent for the treatment of rare earth elements. Through the use of elemental analysis as well as FTIR, SEM, XPS, and Brunauer-Emmett-Teller (BET) surface area measurement, the synthesized polymer was found to have a specific surface area of 111.4 m²·g⁻¹. The adsorption performances of rare metal ions were investigated under different pH levels, contact times, initial concentrations of rare earth ions, and temperatures. The adsorption equilibrium for La³⁺, Ce³⁺, and Y³⁺ onto a polystyrene-poly(hydroxamic acid) copolymer is described by the Langmuir model, which confirms the applicability of monolayer coverage of rare earth ions onto a polystyrene-poly(hydroxamic acid) copolymer. The amount of adsorption capacities for La³⁺, Ce³⁺, and Y³⁺ reached 1.27, 1.53, and 1.83 mmol·g⁻¹ within four hours, respectively. The adsorption process was controlled by liquid film diffusion, particle diffusion, and chemical reaction simultaneously. The thermodynamic parameters, including the change of Gibbs free energy (∆G), the change of enthalpy (∆H), and the change of entropy (∆S), were determined. The results indicate that the adsorption of resins for La³⁺, Ce³⁺ and Y³⁺ was spontaneous and endothermic. The polymer was also used as a recyclable adsorbent by the desorption experiment.