Sandwich Multi-Material 3D-Printed Polymers: Influence of Aging on the Impact and Flexure Resistances

Impact Absorption Power of Polyolefin Fused Filament Fabrication 3D-Printed Sports Mouthguards: In Vitro Study

BACKGROUND/AIM

This study aims to evaluate and compare the impact absorption capacities of thermoformed ethylene vinyl acetate (EVA) mouthguards and 3D-printed polyolefin mouthguards used in sports dentistry applications. The objective is to determine whether 3D-printed polyolefin mouthguards offer superior impact toughness compared to traditional EVA mouthguards commonly used in sports settings.

MATERIALS AND METHODS

Six material samples were assessed: five pressure-formed EVA mouthguards (PolyShok, Buffalo Dental, Erkoflex, Proform, and Drufosoft) and one 3D-printed synthetic polymer (polyolefin). The materials were evaluated using a modified American Society for Testing and Materials (ASTM) D256 Test Method A for Izod pendulum impact resistance of plastics. Polyolefin samples were 3D-printed using fused filament fabrication (FFF) technology. Notably, the FFF process included samples printed with notches placed either parallel or perpendicular to the build direction. This orientation served as a study factor, allowing for comparison of material behavior under different printing conditions. Impact testing was conducted using an Izod impact tester to assess the materials' performance under controlled impact conditions.

RESULTS

The study achieved a high power (1.0) in power analysis, indicating strong sensitivity to detect significant differences. Among molded materials, PolyShok showed significantly lower impact toughness compared to others (p = 0.06). The mean impact absorption of EVA materials was 5.4 ± 0.3 kJ/m2, significantly lower than polyolefin materials, which demonstrated 12.9 ± 0.7 kJ/m2 and superior performance (p = 0.0). Horizontal-notched polyolefin samples exhibited higher impact strength compared to vertical-notched samples (p = 0.009).

CONCLUSIONS

3D-printed polyolefin mouthguards exhibited significantly higher impact toughness than thermoformed EVA mouthguards. While EVA materials demonstrated structural robustness, their lower impact resistance and observed tearing in other test specimens suggest the need for alternative testing standards to better reflect real-world conditions. 3D-printed mouthguards fabricated with build orientations perpendicular to the direction of impact demonstrate significantly enhanced impact absorption. Further research into manufacturing methods and testing protocols is recommended to optimize mouthguard performance under impact scenarios.

The Evolution of Thermoplastic Raw Materials in High-Speed FFF/FDM 3D Printing Era: Challenges and Opportunities

The evolution of thermoplastic materials has played a critical role in advancing high-speed Fused Filament Fabrication (FFF) and Fused Deposition Modeling (FDM) 3D printing technologies. This study explores the performance and challenges associated with next-generation thermoplastics specifically designed for high-speed printing, such as high-speed PLA, ABS, and PETG, in comparison to conventional materials. A systematic analysis was conducted to evaluate the key parameters, including the mechanical properties, layer adhesion, surface finish, and dimensional accuracy, under varying high-speed printing conditions. The results reveal that high-speed thermoplastics, when coupled with advanced hardware and optimized motion control systems, achieve up to a 70% reduction in printing time without significant trade-offs in mechanical integrity or precision. Additionally, the study identifies challenges, such as increased thermal stresses, warping, and the need for precise cooling strategies, which can impact material performance at elevated speeds. Opportunities for future development are also discussed, including the design of novel polymer formulations and hardware innovations to further enhance the reliability and scalability of high-speed FFF/FDM printing. This work underscores the potential of adopting such advanced thermoplastic materials in the high-speed 3D printing era and highlights the critical interplay between material science and hardware engineering for achieving next-generation manufacturing capabilities.

Changes in the Antibacterial Performance of Polymer-Based Nanocomposites Induced by Additive Manufacturing Processing

The idea supporting the investigation of the current manuscript was to develop customized filters for air conditioners with different pore percentages and geometry with the additional advantage of presenting antibacterial performance. This property was expected due to the reinforcement of Cu nanoparticles in the polymeric matrix of poly(lactic acid) (PLA) and polyurethane (TPU). The filaments were characterized by their chemical composition, thermal and mechanical properties, and antibacterial behavior before and after processing by fused filament fabrication. An X-ray photoelectron spectroscopy showed that the nanocomposite filaments presented Cu particles at their surface in different valence states, including Cu0, Cu+, and Cu2+. After processing, the metallic particles are almost absent from the surface, a result confirmed by micro-computer tomography (μ-CT) characterization. Antibacterial tests were made using solid-state diffusion tests to mimic the dry environment in air conditioner filters. The tests with the nanocomposite filaments showed that bacteria proliferation was hindered. However, no antibacterial performance could be observed after processing due to the absence of the metallic element on the surface. Nevertheless, antimicrobial performance was observed when evaluated in liquid tests. Therefore, the obtained results provide valuable indications for developing new nanocomposites that must maintain their antimicrobial activity after being processed and tested in the dry conditions of solid-state diffusion.

Development status of mouthguard

The mouthguard plays a crucial role in preventing damage to the oral and jaw system. However, the popularity of sports mouthguards remains relatively low, and research on sports mouthguards is rather scattered. This paper primarily summarizes the characteristics of materials, production methods, protection principles, and influencing factors of mouthguards, with the aim of providing a theoretical reference for the popularization and application of mouthguards.

Evaluation of Mechanical Properties of ABS-like Resin for Stereolithography Versus ABS for Fused Deposition Modeling in Three-Dimensional Printing Applications for Odontology

This study investigates the differences in mechanical properties between acrylonitrile butadiene styrene (ABS) samples produced using fused deposition modeling (FDM) and stereolithography (SLA) using ABS filaments and ABS-like resin, respectively. The central question is to determine how these distinct printing techniques affect the properties of ABS and ABS-like resin and which method delivers superior performance for specific applications, particularly in dental treatments. The evaluation methods used in this study included Shore D hardness, accelerated aging, tensile testing, Izod impact testing, flexural resistance measured by a 3-point bending test, and compression testing. Poisson's ratio was also assessed, along with microstructure characterization, density measurement, confocal microscopy, dilatometry, wettability, Fourier-transform infrared spectroscopy (FTIR), and nanoindentation. It was concluded that ABS has the same hardness in both manufacturing methods; however, the FDM process results in significantly superior mechanical properties compared to SLA. Microscopy demonstrates a more accurate sample geometry when fabricated with SLA. It is also concluded that printable ABS is suitable for applications in dentistry to fabricate models and surgical guides using the SLA and FDM methods, as well as facial protectors for sports using the FDM method.

The production and materials of mouthguards: Conventional vs additive manufacturing - A systematic review

This investigation presents a critical analysis of mouthguard production, focusing on the evaluation of conventional vs additive manufacturing methods, the materials involved, and aspects such as their failure and prevention. It also summarizes the current trends, perspectives, and the main limitations. It is shown that some of the shortcomings can be solved by implementing additive manufacturing technologies, which are systematically reviewed in this research. Due to the specific materials used to produce mouthguards, there are certain additive manufacturing technologies that dominate and a wide variety of raw materials. The costs vary depending on the technology.

Evaluation of the Effect of Mineral Oil Exposure on Changes in the Structure and Mechanical Properties of Polymer Parts Produced by Additive Manufacturing Techniques

The paper describes the type of changes in the structure and mechanical properties of 3D printed shapes under the influence of mineral oil. The effects of a room (23 °C) and elevated temperature (70 °C) on 3D prints manufactured by the FDM method and stored in oil for 15, 30, and 60 days on the change of properties and structure were investigated. The samples were produced from ABS (poly(acrylonitrile-co-butadiene-co-styrene)), ASA (poly(acrylonitrile-co-styrene-co-acrylate), PLA (poly(lactic acid)), and HIPS (high-impact polystyrene). Tests related to the strength of the materials, such as the static tensile test and Charpy impact test, were carried out. The structure was evaluated using a scanning electron microscope, and changes in chemical structure were determined by conducting FTIR (Fourier transform infrared spectroscopy) and TGA (thermogravimetric analysis) tests. The analysis of the results provided important information about the impact of mineral oil on specific materials. This is critical for designing and manufacturing components that can withstand mineral oil exposure in real-world environments. The materials underwent varying changes. Strength increased for PLA by about 28%, remained unchanged for ABS and HIPS during exposure for 30 days, and decreased for ASA with extended exposure up to 14%.

The effect of aging on the mechanical properties of 3-dimensional printed biocompatible resin materials used in dental applications: An in vitro study

INTRODUCTION

The mechanical properties of biocompatible printable resin materials in an intraoral environment is still being investigated. This study aimed to assess the effect of the aging process on the mechanical properties of resin samples produced by stereolithography appearance (SLA) and digital light processing (DLP) 3-dimensional printer systems.

METHODS

The cylindrical sample (4.00 × 20.00 mm) was designed by software, and the data were transformed into digital format. A DLP printer (n = 40) and an SLA printer (n = 40) carried out the printing process. The aging procedure was applied to 20 samples from each group using a thermocycling device. After the aging procedure, the samples were placed in the universal testing device for the 3-point bending test.

RESULTS

This study showed that the aging procedure decreased maximum load, bending stress, and Young's modulus values and increased maximum deflection values of the DLP group (P <0.01). However, no statistical difference was detected in the parameters compared with the SLA group except for the maximum deflection values. Furthermore, statistically significant differences were found between maximum deflection and Young's module values of SLA and DLP control and study groups (P <0.05).

CONCLUSIONS

This in vitro study revealed that the biocompatible printable resin materials produced by DLP and SLA printers had the mechanical strength to resist the values resembling the physiological occlusal forces even after the aging procedure and could produce intraoral appliances.

Evaluation of Mechanical Properties of 3D-Printed Polymeric Materials for Possible Application in Mouthguards

Custom mouthguards are used in various sports disciplines as a protection for teeth, temporomandibular joints, and soft tissues of the oral cavity from impact forces. The purpose of this research was to evaluate the mechanical properties of flexible polymeric 3D-printable materials and to select a material with the most favourable physical properties for making intraoral protectors. Four 3D-printable polymeric materials were selected for the evaluation: IMPRIMO LC IBT (Scheu-Dental, Iserlohn, Germany), Keyortho IBT (EnvisionTEC, Gladbeck, Germany), IBT (Formlabs, Somerville, MA, USA), and Ortho IBT (NextDent, Utrecht, Netherlands). A total of 176 samples (44 from each material) was 3D-printed using the stereolitography (SLA) technique. Tensile strength, flexural strength, notch-toughness, Shore hardness, sorption, and solubility tests were conducted. The materials were compared using a series of analyses of variance (one-way ANOVA) with Bonferroni post hoc tests. Statistical analyses were performed with the use of IBM SPSS Statistics 28.0.0 software (IBM, New York, NY, USA). Each material was assigned a score from 1 to 4 depending on the individual test results, and tests were given indexes according to the significance of the parameter in the mouthguard protective function. The number of points obtained by each material in each test was then multiplied by the test index, and the results were tabulated. The material with the highest result among the ones studied-most suitable for the application in mouthguard fabrication-was Keyortho IBT from EnvisionTEC.

Resistance of 3D-Printed Components, Test Specimens and Products to Work under Environmental Conditions-Review

The development of additive manufacturing methods known as "3D printing" started in the 1980s. In these methods, spatial models are created from a semi-finished product such as a powder, filament or liquid. The model is most often created in layers, which are created from the semi-finished product, which is most often subjected to thermal treatment or using light or ultraviolet rays. The technology of additive manufacturing has both advantages and disadvantages when compared to the traditionally used methods of processing thermoplastic materials, such as, for example, injection or extrusion. The most important advantages are low cost, flexibility and speed of manufacturing of elements with different spatial shapes. From the point of view of the user of the product, the most important disadvantages are the lower mechanical properties and lower resistance to environmental factors that occur during the use of the manufactured products. The purpose of this review is to present current information and a compilation of features in the field of research on the effects of the interactions of different types of environments on the mechanical properties of 3D-manufactured thermoplastic products. Changes in the structure and mechanical properties of the material under the influence of factors such as humidity, salt, temperature, UV rays, gasoline and the environment of the human body are presented. The presented article enables the effects of environmental conditions on common materials used in 3D printing technology to be collated in one place.

Compression and Bending Properties of Short Carbon Fiber Reinforced Polymers Sandwich Structures Produced via Fused Filament Fabrication Process

Additive manufacturing, through the process of thermoplastic extrusion of filament, allows the manufacture of complex composite sandwich structures in a short time with low costs. This paper presents the design and fabrication by Fused Filament Fabrication (FFF) of composite sandwich structures with short fibers, having three core types C, Z, and H, followed by mechanical performance testing of the structures for compression and bending in three points. Flatwise compression tests and three-point bending have clearly indicated the superior performance of H-core sandwich structures due to dense core structures. The main modes of failure of composite sandwich structures were analyzed microscopically, highlighting core shear buckling in compression tests and face indentation in three-point bending tests. The strength–mass ratio allowed the identification of the structures with the best performances considering the desire to reduce the mass, so: the H-core sandwich structures showed the best results in compression tests and the C-core sandwich structures in three-point bending tests. The feasibility of the FFF process and the three-point bending test of composite wing sections, which will be used on an unmanned aircraft, have also been demonstrated. The finite element analysis showed the distribution of equivalent stresses and reaction forces for the composite wing sections tested for bending, proving to validate the experimental results.

Low-Velocity Impact Behavior of Foam Core Sandwich Panels with Inter-Ply and Intra-Ply Carbon/Kevlar/Epoxy Hybrid Face Sheets

Sandwich composites are extensively employed in a variety of applications because their bending stiffness affords a greater advantage than composite materials. However, the aspect limiting the application of the sandwich material is its poor impact resistance. Therefore, understanding the impact properties of the sandwich structure will determine the ways in which it can be used under the conditions of impact loading. Sandwich panels with different combinations of carbon/Kevlar woven monolithic face sheets, inter-ply face sheets and intra-ply face sheets were fabricated, using the vacuum-assisted resin transfer process. Instrumented low-velocity impact tests were performed using different energy levels of 5 J, 10 J, 20 J, 30 J and 40 J on a variety of samples and the results were assessed. The damage caused by the modes of failure in the sandwich structure include fiber breakage, matrix cracking, foam cracking and debonding. In sandwich panels with thin face sheets, the maximum peak load was achieved for the inter-ply hybrid foam core sandwich panel in which Kevlar was present towards the outer surface and carbon in the inner surface of the face sheet. At an impact energy of 40 J, the maximum peak load for the inter-ply hybrid foam core sandwich panel was 31.57% higher than for the sandwich structure in which carbon is towards the outer surface and Kevlar is in the inner surface of the face sheet. The intra-ply hybrid foam core sandwich panel subjected to 40 J impact energy demonstrated a 13.17% higher maximum peak load compared to the carbon monolithic face sheet sandwich panel. The experimental measurements and numerical predictions are in close agreement.