Formation and Investigation of Mechanical, Thermal, Optical and Wetting Properties of Melt-Spun Multifilament Poly(lactic acid) Yarns with Added Rosins

A MAX phase (Ti3AlC2) as a performance enhancer for poly(lactic acid) electrospun membranes in steam generation and solar desalination

Clean water and sanitation issues motivate researchers to develop water evaporators for freshwater generation. The composite membrane evaporator was electrospun herein based on poly(lactic acid) (PLA) and Ti3AlC2 MAX phase as a property enhancer. As a precursor for the MXenes synthesis, the MAX phase has never been explored with PLA for water evaporator potential. Alternative use of the MAX phase can reduce the production cost arising from chemical synthesis. This work explored the potential of the MAX phase as an additive to enhance PLA membrane performance for steam generation and desalination applications. Under the infrared irradiation (∼1.0 kW/m2), the mechanically-improved PLA/MAX phase membrane showed an enhanced water evaporation rate of 1.70 kg/m2 h (93.93 % efficiency), with an approximately 52 % rate increment relative to the PLA membrane. Based on the artificial seawater (3.5 % w/w), the membrane exhibited an evaporation rate of 1.60 kg/m2 h (87.57 % efficiency). The membrane showed self-floating ability at the air-water interface, excellent thermal stability over the entire operating temperatures, and reusability after repeated cycles. Moreover, the generated freshwater contained exceptionally low cations concentrations, as low as those in potable water. The developed composite membrane also had proved its potential for solar desalination in the water generation field.

Nanoplastics from disposable paper cups and microwavable food containers

Nanoplastics (NPs, <1 µm) pose greater risks due to their increased absorption rates in biological systems. In this study, we investigated the release of NPs from paper cups and microwavable food containers coated with low-density polyethylene (LDPE) and polylactic acid (PLA). For disposable paper cups, we found that LDPE-coated cups released up to 26-fold more NPs (maximum 1.9 × 107 per cup) than PLA-coated ones. The NPs release from LDPE-coated cups was increased at high temperatures above 80 °C, and further increased by physical agitation. However, negligible NP release was observed when the inner coating thickness exceeded 1 mm. For microwavable food containers, those with PLA coatings were more susceptible to the effects of microwave. Depending on the cooking time, we noticed a significant difference (up to 40000 times) in the number of released NPs between LDPE and PLA coatings. Additionally, higher microwave power level led to an increase of NPs, even with constant total energy input. Considering the release of NP, PLA coatings for disposable paper cups and LDPE coatings for microwavable food containers seem more suitable. Furthermore, our results suggest that multi-use cups significantly reduce NPs release due to their material thickness, making them a safer alternative to disposable ones.

Sonochemical Synthesis of Magnetite/Poly(lactic acid) Nanocomposites

Nanocomposites based on poly(lactic acid) (PLA) and magnetite nanoparticles (MNP-Fe3O4) show promise for applications in biomedical treatments. One key challenge is to improve the stabilization and dispersion of MNP-Fe3O4. To address this, we synthesized MNP-Fe3O4/PLA nanocomposites using ultrasound mediation and a single iron(II) precursor, eliminating the need for surfactants or organic solvents, and conducted the process under ambient conditions. The resulting materials, containing 18 and 33 wt.% Fe3O4, exhibited unique thermal behavior characterized by two mass losses: one at a lower degradation temperature (Td) and another at a higher Td compared to pure PLA. This suggests that the interaction between PLA and MNP-Fe3O4 occurs through hydrogen bonds, enhancing the thermal stability of a portion of the polymer. Fourier Transform Infrared (FT-IR) analysis supported this finding, revealing shifts in bands related to the terminal -OH groups of the polymer and the Fe-O bonds, thereby confirming the interaction between the groups. Raman spectroscopy demonstrated that the PLA serves as a protective layer against the oxidation of MNP-Fe3O4 in the 18% MNP-Fe3O4/PLA nanocomposite when exposed to a high-power laser (90 mW). Transmission Electron Microscopy (TEM) and Scanning Electron Microscopy (SEM) analyses confirmed that the synthetic procedure yields materials with dispersed nanoparticles within the PLA matrix without the need for additional reactants.

3D-Printed Piezoelectret Based on Foamed Polylactic Acid for Energy-Harvesting and Sensing Applications

Poly(lactic) acid (PLA) is a bio-compatible polymer widely used in additive manufacturing, and in the form of cellular foam it shows excellent mechanical and piezoelectric properties. This type of structure can be easily 3D-printed by Fusion Deposition Modelling (FDM) with commercially available composite filaments. In this work, we present mechanical and electrical investigations on 3D-printed low-cost and eco-friendly foamed PLA. The cellular microstructure and the foaming degree were tuned by varying extrusion temperature and flowrate. The maximum surface potential and charge stability of disk samples were found in correspondence of extrusion temperature between 230 and 240 °C with a flowrate of 53-44% when charging on a heated bed at 85 °C. The cells' morphology and correlated mechanical properties were analyzed and the measured piezoelectric d33 coefficient was found to be 212 pC/N. These findings show the importance of printing parameters and thermal treatment during the charging process in order to obtain the highest charge storage, stability and material flexibility. These results suggest that 3D-printed cellular PLA is a promising sustainable material for sensing and energy-harvesting applications.

Polymers and Nanotechnology for Industry 4.0

The term "polymer" derives from the Greek words "πολύς" meaning "many, much" and "μέρος" meaning "part", and was proposed in 1833 by Jöns Jacob Berzelius, albeit with a different definition from the current IUPAC definition [...].

Experimental Investigation of the Tensile Behavior of Selected Tire Cords Using Novel Testing Equipment

Aramid and polyamide cords are used in a wide range of applications, particularly in the automotive industry (tire reinforcement) and textile industry for military and fireguard purposes. The problem of the reliable experimental study of tensile behavior of synthetic cords is considered in this paper. In the available standards for synthetic cord testing, particularly ASTM D 885-03, the tensile test must result with the cord damage in the middle of gauge length, and the cords should be fixed in the machine clamps. The trial test gave damage near the clamps. We propose a novel testing stage mounted in the testing machine clamps to achieve the uniform tensile stress distribution in the gauge length of the measured cords. The results of the deformations were measured in two ways: using testing machine head displacement and a videoextensometer. Stress curves of four distinguished cords were evaluated and compared. The second method allowed to acquire results differing from the manufacturers' data from 0.7% to 21.5%, which allowed for the conclusion that the designed test stand allows for obtaining reliable results for stretched cords.