Polymer blend lithography for metal films: large-area patterning with over 1 billion holes/inch(2)

Tip-Induced Nanopatterning of Ultrathin Polymer Brushes

Patterned, ultra-thin surface layers can serve as templates for positioning nanoparticlesor targeted self-assembly of molecular structures, for example, block-copolymers. This work investigates the high-resolution, atomic force microscopebased patterning of 2 nm thick vinyl-terminated polystyrene brush layers and evaluates the line broadening due to tip degradation. This work compares the patterning properties with those of a silane-based fluorinated self-assembled monolayer (SAM), using molecular heteropatterns generated by modified polymer blend lithography (brush/SAM-PBL). Stable line widths of 20 nm (FWHM) over lengths of over 20000 µm indicate greatly reduced tip wear, compared to expectations on uncoated SiO_x surfaces. The polymer brush acts as a molecularly thin lubricating layer, thus enabling a 5000 fold increase in tip lifetime, and the brush is bonded weakly enough that it can be removed with surgical accuracy. On traditionally used SAMs, either the tip wear is very high or the molecules are not completely removed. Polymer Phase Amplified Brush Editing is presented, which uses directed self-assembly to amplify the aspect ratio of the molecular structures by a factor of 4. The structures thus amplified allow transfer into silicon/metal heterostructures, fabricating 30 nm deep, all-silicon diffraction gratings that could withstand focused high-power 405 nm laser irradiation.

Water vapor induced self-assembly of islands/honeycomb structure by secondary phase separation in polystyrene solution with bimodal molecular weight distribution

The formation of complex structures in thin films is of interest in many fields. Segregation of polymer chains of different molecular weights is a well-known process. However, here, polystyrene with bimodal molecular weight distribution, but no additional chemical modification was used. It was proven that at certain conditions, the phase separation occurred between two fractions of bimodal polystyrene/methyl ethyl ketone solution. The films were prepared by spin-coating, and the segregation between polystyrene phases was investigated by force spectroscopy. Next, water vapour induced secondary phase separation was investigated. The introduction of moist airflow induced the self-assembly of the lower molecular weight into islands and the heavier fraction into a honeycomb. As a result, an easy, fast, and effective method of obtaining island/honeycomb morphologies was demonstrated. The possible mechanisms of the formation of such structures were discussed.

Tuning the Wettability of a Thin Polymer Film by Gradually Changing the Geometry of Nanoscale Pore Edges

Controlling wetting of solids by liquids attracts attention because of its scientific and technological importance. In this paper, the wettability of a highly uniform porous poly(methyl methacrylate) film on a silicon substrate containing a high density of randomly distributed self-similar pores was gradually tuned by changing the shape of nanometric crownlike structures around the pores. Fine-tuning the topography of these thin films was performed by isothermal annealing. The equilibrium contact angle of a water droplet placed on the surface of the films could be varied from 72 to 102°. The contact angle changes were assumed to be a consequence of changes in surface topography in the nanoscale. A simple method of a quantitative description of the change of the topography of these films was developed. Critical dimensions of these films were determined in horizontal and vertical directions relative to the surface plane. The slope coefficient (SC) describing how sharp the structures are, is defined as the ratio between the critical dimensions: the root-mean-square roughness σ and the autocorrelation length ξ. For SC > 0.08, the contact angle increased proportionally to the value of SC, whereas for SC < 0.08, the contact angle proportionally decreased. At the highest SC values, the contact angles were 6-10% higher than those predicted for flat porous surfaces using the Cassie-Baxter equation. We suggest that this discrepancy is due to the capillary tension caused by the submicron-scale undulation of the triple line, which was found to be proportional to the height of the crownlike pore edges and the value of SC. The same effect is responsible for the linear dependence of the contact angle on the SC value.

Conformational sensitivity of surface selection rules for quantitative Raman identification of small molecules in biofluids

Biofluid analysis by surface-enhanced Raman scattering (SERS) is usually hindered by nonspecific interferences. It is challenging to drive targeted molecules towards sensitive areas with specific capture and quantitative recognition in complex biofluids. Herein, a highly specific and quantitative SERS analyzer for small molecule dopamine (DA) in serum is demonstrated on a portable Raman device by virtue of a transducer of mercaptophenylboronic acid (MPBA) and a site-directed decoration of plasmonic Ag dendrites on a superhydrophobic surface. Theoretical simulations of molecular vibrations and charge distributions demonstrate the predomination of Raman surface selection rules in molecular reorientation upon the binding of DA. This recognition event is translated into ratiometric changes in the spectral profile which evidences excellent capability on SERS quantitation. The rules can well distinguish DA from its common interferents including fructose, glucose, sucrose and ascorbic acid which all generate weak but completely opposite spectral changes. Moreover, benefitting from the wettability difference, the target DA in diluted serum can be specifically enriched on a transducer-capped Ag surface, and the adsorption of other interferences is resisted by superhydrophobic features. It paves a new way for labelling a single SERS tag to simultaneously realize the identification and quantification of small molecules in complex biological media.

Light trapping in thin film silicon solar cells via phase separated disordered nanopillars

In this work, we have improved the absorption properties of thin film solar cells by introducing light trapping reflectors deposited onto self-assembled nanostructures. The latter consist of a disordered array of nanopillars and are fabricated by polymer blend lithography. Their broadband light scattering properties are exploited to enhance the photocurrent density of thin film devices, here based on hydrogenated amorphous silicon active layers. We demonstrate that these light scattering nanopillars yield a short-circuit current density increase of +33%rel with respect to equivalent solar cells processed on a planar reflector. Moreover, we experimentally show that they outperform randomly textured substrates that are commonly used for achieving efficient light trapping. Complementary optical simulations are conducted on an accurate 3D model to analyze the superior light harvesting properties of the nanopillar array and to derive general design rules. Our approach allows one to easily tune the morphology of the self-assembled nanostructures, is up-scalable and operated at room temperature, and is applicable to other photovoltaic technologies.

Two-dimensional self-assembly of diacetylenic acid derivatives and their light-induced polymerization on HOPG surfaces

The effect of UV illumination time on the polymerization efficiency and the structural change of DA-25.

Graphene-enhanced plasmonic nanohole arrays for environmental sensing in aqueous samples

The label-free nature of surface plasmon resonance techniques (SPR) enables a fast, specific, and sensitive analysis of molecular interactions. However, detection of highly diluted concentrations and small molecules is still challenging. It is shown here that in contrast to continuous gold films, gold nanohole arrays can significantly improve the performance of SPR devices in angle-dependent measurement mode, as a signal amplification arises from localized surface plasmons at the nanostructures. This leads consequently to an increased sensing capability of molecules bound to the nanohole array surface. Furthermore, a reduced graphene oxide (rGO) sensor surface was layered over the nanohole array. Reduced graphene oxide is a 2D nanomaterial consisting of sp²-hybridized carbon atoms and is an attractive receptor surface for SPR as it omits any bulk phase and therefore allows fast response times. In fact, it was found that nanohole arrays demonstrated a higher shift in the resonance angle of 250-380% compared to a continuous gold film. At the same time the nanohole array structure as characterized by its diameter-to-periodicity ratio had minimal influence on the binding capacity of the sensor surface. As a simple and environmentally highly relevant model, binding of the plasticizer diethyl phthalate (DEP) via π-stacking was monitored on the rGO gold nanohole array realizing a limit of detection of as low as 20 nM. The concentration-dependent signal change was studied with the best performing rGO-modified nanohole arrays. Compared to continuous gold films a diameter-to-periodicity ratio (D/P) of 0.43 lead to a 12-fold signal enhancement. Finally, the effect of environmental waters on the sensor was evaluated using samples from sea, lake and river waters spiked with analytically relevant amounts of DEP during which significant changes in the SPR signal are observed. It is expected that this concept can be successfully transferred to enhance the sensitivity in SPR sensors.

Novel roles for well-known players: from tobacco mosaic virus pests to enzymatically active assemblies

The rod-shaped nanoparticles of the widespread plant pathogen tobacco mosaic virus (TMV) have been a matter of intense debates and cutting-edge research for more than a hundred years. During the late 19th century, their behavior in filtration tests applied to the agent causing the 'plant mosaic disease' eventually led to the discrimination of viruses from bacteria. Thereafter, they promoted the development of biophysical cornerstone techniques such as electron microscopy and ultracentrifugation. Since the 1950s, the robust, helically arranged nucleoprotein complexes consisting of a single RNA and more than 2100 identical coat protein subunits have enabled molecular studies which have pioneered the understanding of viral replication and self-assembly, and elucidated major aspects of virus-host interplay, which can lead to agronomically relevant diseases. However, during the last decades, TMV has acquired a new reputation as a well-defined high-yield nanotemplate with multivalent protein surfaces, allowing for an ordered high-density presentation of multiple active molecules or synthetic compounds. Amino acid side chains exposed on the viral coat may be tailored genetically or biochemically to meet the demands for selective conjugation reactions, or to directly engineer novel functionality on TMV-derived nanosticks. The natural TMV size (length: 300 nm) in combination with functional ligands such as peptides, enzymes, dyes, drugs or inorganic materials is advantageous for applications ranging from biomedical imaging and therapy approaches over surface enlargement of battery electrodes to the immobilization of enzymes. TMV building blocks are also amenable to external control of in vitro assembly and re-organization into technically expedient new shapes or arrays, which bears a unique potential for the development of 'smart' functional 3D structures. Among those, materials designed for enzyme-based biodetection layouts, which are routinely applied, e.g., for monitoring blood sugar concentrations, might profit particularly from the presence of TMV rods: Their surfaces were recently shown to stabilize enzymatic activities upon repeated consecutive uses and over several weeks. This review gives the reader a ride through strikingly diverse achievements obtained with TMV-based particles, compares them to the progress with related viruses, and focuses on latest results revealing special advantages for enzyme-based biosensing formats, which might be of high interest for diagnostics employing 'systems-on-a-chip'.

Shape-Directed Patterning and Surface Reaction of Tetra-diacetylene Monolayers: Formation of Linear and Two-Dimensional Grid Polydiacetylene Alternating Copolymers

Side chains containing two diacetylene units spaced by an odd number of methylene units exhibit pronounced “bumps” composed of 0.3 nm steps, in opposite directions, at odd and even side-chain positions. In densely packed self-assembled monolayers, the bis-diacetylene bumps stack into each other, similar to the stacking of paper cups. Bis-diacetylene side chain structure and associated packing constraints can be tailored by altering the bump width, direction, side-chain location, and overall side-chain length as a means to direct the identities and alignments of adjacent molecules within monolayers. Scanning tunneling microscopy (STM) at the solution–HOPG interface confirms the high selectivity and fidelity with which bis-diacetylene bump stacking directs the packing of shape-complementary side chains within one-component monolayers and within two-component, 1-D self-patterned monolayers. Drop cast or moderately annealed monolayers of anthracenes bearing two bis-diacetylene side chains assemble single domains as large as 10(5) nm2. Light-induced cross-linking of two-component, 1-D patterned monolayers generates linear polydiacetylene alternating copolymers (A-B-)x and 2-D grid polydiacetylene alternating copolymers (A(-B-)(-B-)A(-B-)(-B-))x that covalently lock in monolayer structure and patterns.