Silicon microgrooves for contact guidance of human aortic endothelial cells

Micropatterned Fibrous Scaffold Produced by Using Template-Assisted Electrospinning Technique for Wound Healing Application

This paper describes the fabrication of a structural scaffold consisting of both randomly oriented nanofibers and triangular prism patterns on the scaffold surface using a combination technique of electrospinning and collector templates. The polycaprolactone (PCL) nanofibers were electrospun over a triangular prism pattern mold, which acted as a template. The deposited scaffold was removed from the template to produce a standalone structural scaffold of three-dimensional micropatterned nanofibers. The fabricated structural scaffold was compared with flat randomly oriented nanofibers based on in vitro and in vivo studies. The in vitro study indicated that the structural scaffold demonstrated higher fibroblast cell proliferation, cell elongation with a 13.48 ± 2.73 aspect ratio and 70% fibroblast cell orientation compared with flat random nanofibers. Among the treatment groups, the structural scaffold escalated the wound closure to 92.17% on day 14. Histological staining of the healed wound area demonstrated that the structural scaffold exhibited advanced epithelization of the epidermal layer accompanied by mild inflammation. The proliferated fibroblast cells and collagen fibers in the structural scaffold appeared denser and arranged more horizontally. These results determined the potential of micropatterned scaffolds for stimulating cell behavior and their application for wound healing.

An engraved surface induces weak adherence and high proliferation of nonadherent cells and microorganisms during culture

When cells are cultured in a Petri dish, the adherent cells attach to the bottom of the dish; whereas, the nonadherent cells float in the culture medium. It was observed that nonadherent cells could be induced to adherent-like cells when cultured in an engraved plastic dish (biosimulator). The adherence of these cells to the engraved surface could be prevented with inhibitors specific for adhesion. It was also observed that culturing microorganisms of the environment in a biosimulator induced weak adhesion and high proliferation. Analysis of the microbiome using 16S rRNA profiling demonstrated that the biosimulator was more efficient in inducing proliferation of several phyla of microorganisms compared with culture by conventional techniques.

Collagen and fibronectin surface modification of nanoporous anodic alumina and macroporous silicon for endothelial cell cultures

BACKGROUND

The ability to direct the cellular response by means of biomaterial surface topography is important for biomedical applications. Substrate surface topography has been shown to be an effective cue for the regulation of cellular response. Here, the response of human aortic endothelial cells to nanoporous anodic alumina and macroporous silicon with collagen and fibronectin functionalization has been studied.

METHODS

Confocal microscopy and scanning electron microscopy were employed to analyse the effects of the material and the porosity on the adhesion, morphology, and proliferation of the cells. Cell spreading and filopodia formation on macro- and nanoporous material was characterized by atomic force microscopy. We have also studied the influence of the protein on the adhesion.

RESULTS

It was obtained the best results when the material is functionalized with fibronectin, regarding cells adhesion, morphology, and proliferation.

CONCLUSION

These results permit to obtain chemical modified 3D structures for several biotechnology applications such as tissue engineering, organ-on-chip or regenerative medicine.

Effectiveness of a low-fat yoghurt supplemented with rooster comb extract on muscle strength in adults with mild knee pain and mechanisms of action on muscle regeneration

PURPOSE

To determine the effects of the intake of low-fat yoghurt supplemented with rooster comb extract (RCE) on muscle strength.

METHODS AND RESULTS

148 subjects, with mild knee pain, participated in a randomized, placebo-controlled, double-blind, and parallel study. Muscle strength, knee effusion, and pain perception were measured. C2C12 myoblasts were used to elucidate the mechanisms of action involved. RCE improved total work and mean power in men, and also peak torque in extension by 10%. RCE reduced synovial effusion by 11.8% and pain perception by 24.6%. Both RCE and HA increased myoblast proliferation by 29%, while RCE reduced myoblast differentiation by 36.2%, suggesting a beneficial role of RCE in muscle regeneration.

CONCLUSIONS

Low-fat yoghurt supplemented with RCE improved muscle strength. This effect is partially explained by muscle regeneration enhancement, reduced synovial effusion, and reduced pain perception, which could exert a beneficial clinical impact on men affected by mild knee pain.

Preparation of micro/nanopatterned gelatins crosslinked with genipin for biocompatible dental implants

Background: Collagen is a basic component of the periodontium and plays an important role in the function of the periodontal unit. Therefore, coating with collagen/gelatin has been applied to enable dental implants to positively interact with peri-implant tissues. Although the micro/nanoscale topography is an important property of the surface of dental implants, smaller collagen/gelatin surface patterns have not been sufficiently developed. Furthermore, only few reports on the behavior of cells on gelatin surfaces with different patterns and sizes exist. In this study, we developed micro/nanometer-scaled gelatin surfaces using genipin crosslinking, with the aim of understanding the use of patterning in surface modification of dental implants. Results: Grooves, holes, and pillars, with widths or diameters of 2 µm, 1 µm, or 500 nm were fabricated using a combination of molding and genipin crosslinking of gelatin. The stability of the different gelatin patterns could be controlled by the degree of genipin crosslinking. The gelatin patterns at 20 mM concentration of genipin and 41% crosslinking maintained a stable, patterned shape for at least 14 days in a cell culture medium. A cell morphology study showed that the cells on groves were aligned along the direction of the grooves. In contrast, the cells on pillars and holes exhibited randomly elongated filopodia. The vinculin spots of the cells were observed on the top of ridges and pillars or the upper surface of holes. The results of a cell attachment assay showed that the number of surface-attached cells increased with increasing patterning of the gelatin surface. Unlike the cell attachment assay, the results of a cell proliferation assay showed that Saos-2 cells prefer grooves with diameters of approximately 2 µm and 1 µm and pillars with diameters of 1 µm and heights of 500 nm. The number of cells on pillars with heights of 2 µm was larger than those of the other gelatin surface patterns tested. Conclusion: These data support that a detailed design of the gelatin surface pattern can control both cell attachment and proliferation of Saos-2 cells. Thus, gelatin surfaces patterned using genipin crosslinking are now an available option for biocompatible material patterning.

Engineering Cardiovascular Implant Surfaces to Create a Vascular Endothelial Growth Microenvironment

Cardiovascular disease (CVD) is generally accepted as the leading cause of morbidity and mortality worldwide, and an increasing number of patients suffer from atherosclerosis and thrombosis annually. To treat these disorders and prolong the sufferers' life, several cardiovascular implants have been developed and applied clinically. Nevertheless, thrombosis and hyperplasia at the site of cardiovascular implants are recognized as long-term problems in the practice of interventional cardiology. Here, we start this review from the clinical requirement of the implants, such as anti-hyperplasia, anti-thrombosis, and pro-endothelialization, wherein particularly focus on the natural factors which influence functional endothelialization in situ, including the healthy smooth muscle cells (SMCs) environment, blood flow shear stress (BFSS), and the extracellular matrix (ECM) microenvironment. Then, the currently available strategies on surface modification of cardiovascular biomaterials to create vascular endothelial growth microenvironment are introduced as the main topic, e.g., BFSS effect simulation by surface micro-patterning, ECM rational construction and SMCs phenotype maintain. Finally, the prospects for extending use of the in situ construction of endothelial cells growth microenvironment are discussed and summarized in designing the next generation of vascular implants.