Improving the Catalytic Performance of BaMn0.7Cu0.3O3 Perovskite for CO Oxidation in Simulated Cars Exhaust Conditions by Partial Substitution of Ba

The sol-gel method, adapted to aqueous media, was used for the synthesis of BaMn0.7Cu0.3O3 (BMC) and Ba0.9A0.1Mn0.7Cu0.3O3 (BMC-A, A = Ce, La or Mg) perovskite-type mixed oxides. These samples were fully characterized by ICP-OES, XRD, XPS, H2-TPR, BET, and O2-TPD and, subsequently, they were evaluated as catalysts for CO oxidation under different conditions simulating that found in cars exhaust. The characterization results show that after the partial replacement of Ba by A metal in BMC perovskite: (i) a fraction of the polytype structure was converted to the hexagonal BaMnO3 perovskite structure, (ii) A metal used as dopant was incorporated into the lattice of the perovskite, (iii) oxygen vacancies existed on the surface of samples, and iv) Mn(IV) and Mn(III) coexisted on the surface and in the bulk, with Mn(IV) being the main oxidation state on the surface. In the three reactant atmospheres used, all samples catalysed the CO to CO2 oxidation reaction, showing better performances after the addition of A metal and for reactant mixtures with low CO/O2 ratios. BMC-Ce was the most active catalyst because it combined the highest reducibility and oxygen mobility, the presence of copper and of oxygen vacancies on the surface, the contribution of the Ce(IV)/Ce(III) redox pair, and a high proportion of surface and bulk Mn(IV). At 200 °C and in the 0.1% CO + 10% O2 reactant gas mixture, the CO conversion using BMC-Ce was very similar to the achieved with a 1% Pt/Al2O3 (Pt-Al) reference catalyst.

Co-Exsolution of Ni-Based Alloy Catalysts for the Valorization of Carbon Dioxide and Methane

ConspectusThe reversible coexsolution mechanism of perovskite oxides is emerging as an alternative method for synthesizing alloy catalyst nanoparticles. Co-exsolution is a partial decomposition process where multiple B cations diffuse from the bulk of a solid precursor and nucleate on the surface. The unique properties of exsolved alloy catalysts, including improved dispersion, thermal stability, and compositional malleability, make them particularly useful for converting CO2 into chemical commodities and fuels. However, the coexsolution of alloys is still in development, and fundamental insights into the alloying mechanism, formation of nanoparticles, and defect chemistry are needed.This Account examines the solid-state chemistry of perovskite oxide precursors and reaction parameters that can be altered to control the assembly or exsolution of Ni-based alloys. The characteristics of bulk perovskite oxide precursors heavily influence the exsolved alloy catalyst nanoparticle assembly, growth, and composition. Inherent defects, such as oxygen vacancies and grain boundaries, primarily facilitate the transport of catalytic B-cation dopants from the bulk to the surface. An example of how bulk defects can affect the properties of Ni-based alloy catalysts is demonstrated through the formation of NiFe from La(Fe, Ni)O3. The A/B cation ratio plays a significant role in determining the size and composition of NiFe nanoparticles, which directly impacts their catalytic performance. Using in situ X-ray absorption spectroscopy (in situ XAS), the dynamic behavior of exsolved NiFe nanoparticles can be observed in different reaction environments (oxidation, reduction, and dry reforming of methane) by tracking the oxidation state and local environment of the Ni K-edge and Fe K-edge using X-ray absorption near-edge structure (XANES) and extended X-ray absorption fine structure (EXAFS), respectively. Time-resolved experiments with in situ XAS showed that NiFe nanoparticle growth starts at ∼280 °C and transforms from predominantly Ni to NiFe at higher reduction times and temperatures.The challenges of exsolution of higher-order Ni-based alloys, such as 3(NiFeCo), 4(NiCoCuPd), and 5(NiFeCoCuPd) element nanoparticles, to improve the catalyst properties are discussed. The size, concentration, and reducibility of the dopant cation can alter the exsolution kinetics, alloy nanoparticle growth dynamics, and catalyst performance. The size and composition of exsolved Ni-based alloys affect the effectiveness of catalysts in the dry reforming of methane. Large NiFeCo nanoparticles separated from Pd and Cu can lead to catalyst deactivation, but using a complex alloy with smaller NiFeCoPdCu nanoparticles results in a stable performance. The use of in situ XANES reveals how the dry reforming of methane reaction conditions can induce changes in the NiFe with the rapid redissolution of Fe back into the lattice.The dynamicity of the exsolved Ni-based alloy nanoparticles and implications for their regeneration after aging or exposure to waste gas contaminants are discussed. Finally, we summarize the Account and provide promising future directions.

Screening Ba0.9A0.1MnO3 and Ba0.9A0.1Mn0.7Cu0.3O3 (A = Mg, Ca, Sr, Ce, La) Sol-Gel Synthesised Perovskites as GPF Catalysts

Ba0.9A0.1MnO3 (BM-A) and Ba0.9A0.1Mn0.7Cu0.3O3 (BMC-A) (A = Mg, Ca, Sr, Ce, La) perovskite-type mixed oxides were synthesised, characterised, and used for soot oxidation in simulated Gasoline Direct Injection (GDI) engine exhaust conditions. The samples have been obtained by the sol-gel method in an aqueous medium and deeply characterised. The characterization results indicate that the partial substitution of Ba by A metal in BaMnO3 (BM) and BaMn0.7Cu0.3O3 (BMC) perovskites: (i) favours the hexagonal structure of perovskite; (ii) improves the reducibility and the oxygen desorption during Temperature-Programmed Desorption (O2-TPD) tests and, consequently, the oxygen mobility; (iii) mantains the amount of oxygen vacancies and of Mn(IV) and Mn(III) oxidation states, being Mn(IV) the main one; and (iv) for Ba0.9A0.1Mn0.7Cu0.3O3 (BMC-A) series, copper is partially incorporated into the structure. The soot conversion data reveal that Ba0.9La0.1Mn0.7Cu0.3O3 (BMC-La) is the most active catalyst in an inert (100% He) reaction atmosphere, as it presents the highest amount of copper on the surface, and that Ba0.9Ce0.1MnO3 (BM-Ce) is the best one if a low amount of O2 (1% O2 in He) is present, as it combines the highest emission of oxygen with the good redox properties of Ce(IV)/Ce(III) and Mn(IV)/Mn(III) pairs.

Analysis of the photocatalytic activity of La0.9Sr0.1Fe0.8Co0.2O3±δ perovskite as a catalyst in the degradation of RB-5 dye

The photocatalytic efficiency of some semiconductors depends mainly on their morphological, optical, and structural properties, which can be modified by varying the calcination temperature. In order to evaluate how these properties change, as a function of temperature in a AA'BB'O3 perovskite material, La0.9Sr0.1Fe0.8Co0.2O3±δ (LSFC) was synthesized by the Pechini method and calcined at different temperatures (600 °C, 700 °C, 800 °C, and 900 °C). All the samples were characterized structurally, morphologically, and optically by XRD, SEM, and UV-Vis spectroscopy. Additionally, specific surface area and pore size distribution were calculated by BET and BHJ methods. LSFC was evaluated as photocatalyst material, estimating the degradation of reactive black 5 (RB5), employing as irradiation source UV light and sunlight. The obtained results display a clear tendency between the photoactivity and the heat treatment: degradation percentage decreases as the calcination temperature increases mainly due to the crystal and grain size and, furthermore, loss of porosity and the decrease in surface area, affecting the photocatalytic activity (98%, 95%, 74%, and 50% degradation, respectively). All the ceramic samples follow a pseudo-first-order reaction.