Removal of heavy metal(loid)s from aqueous solution by biogenic FeS-kaolin composite: Behaviors and mechanisms

Study on the adsorption of Zn(II) and Cu(II) in acid mine drainage by fly ash loaded nano-FeS

Aiming at the acid mine drainage (AMD) in zinc, copper and other heavy metals treatment difficulties, severe pollution of soil and water environment and other problems. Through the ultrasonic precipitation method, this study prepared fly ash-loaded nano-FeS composites (nFeS-F). The effects of nFeS-F dosage, pH, stirring rate, reaction time and initial concentration of the solution on the adsorption of Zn(II) and Cu(II) were investigated. The data were fitted by Lagergren first and second-order kinetic equations, Internal diffusion equation, Langmuir and Freundlich isotherm models, and combined with SEM, TEM, FTIR, TGA, and XPS assays to reveal the mechanism of nFeS-F adsorption of Zn(II) and Cu(II). The results demonstrated that: The removal of Zn(II) and Cu(II) by nFeS-F could reach 83.36% and 70.40%, respectively (The dosage was 8 g/L, pH was 4, time was 150 min, and concentration was 100 mg/L). The adsorption process, mainly chemical adsorption, conforms to the Lagergren second-order kinetic equation (R2 = 0.9952 and 0.9932). The adsorption isotherms have a higher fitting degree with the Langmuir model (R2 = 0.9964 and 0.9966), and the adsorption is a monolayer adsorption process. This study can provide a reference for treating heavy metals in acid mine drainage and resource utilization of fly ash.

Selective immobilization of Pb(II) by biogenic whewellite and its mechanism

The development of bio-adsorbents with highly selective immobilization properties for specific heavy metals is a great challenge, but has important application value. Biogenic whewellite (BW) with high selectivity for Pb(II) was synthesized by mineral microbial transformation. The selective immobilization properties and mechanism of BW for Pb(II) were analyzed by combining mineral characterization technology and batch adsorption research methods. The results indicated that BW can efficiently and selectively immobilize Pb(II) in single or composite heavy metal adsorption solutions, and the immobilized Pb(II) is difficult to desorb. BW undergoes monolayer adsorption on Pb(II), Qmax ≈ 1073.17 mg/g. The immobilization of Pb(II) by BW is a physico-chemical adsorption process with spontaneous heat absorption and an accompanying increase in entropy. In addition, the sequestration of Pb(II) by BW remains around 756.99 mg/g even at pH = 1. The excellent selective immobilization properties of BW for Pb(II) are closely related to its smaller Ksp, electrostatic repulsion effect, organic-inorganic composite structure, acid resistance and the formation of Pb(II) oxalate. This study provides beneficial information about the recycling of lead in acidic lead-containing wastewater and composite heavy metal contaminated water bodies.

Adsorption of Sb(III) and Pb(II) in wastewater by magnetic γ-Fe2O3-loaded sludge biochar: Performance and mechanisms

Magnetically modified carbon-based adsorbent (BC@γ-Fe2O3) was prepared through facile route using activated sludge biomass and evaluated for the simultaneous removal of Sb(III) and Pb(II). BC@γ-Fe2O3 exhibited outstanding Sb(III) and Pb(II) adsorption capacity when 200 mg of adsorbent was employed at pH 5.0 for 240 min, with the removal efficiency higher than 90%. The experiments demonstrated the excellent reusability and the potent anti-interference properties of the prepared absorbent. Freundlich and pseudo-second-order kinetic were prior to describe the adsorption process. The adsorption of Sb(III) and Pb(II) onto BC@γ-Fe2O3 was spontaneous and endothermic. BC@γ-Fe2O3 with high specific surface area revealed the exceptional competence to absorb Sb(III) and Pb(II) through pore filling, electrostatic adsorption and complexation. The adsorption mechanisms of Sb(III) and Pb(II) showed similarities with slight disparities. The removal of Sb(III) involved the Fe-O-Sb bond and π-π bond, while the adsorption of Pb(II) was closely related to ion exchange. Moreover, Sb(III) was oxidized to Sb(V) in a minor part during adsorption. The Fe-O-Cl active sites on BC allowed for the binding of γ-Fe2O3, guaranteeing the abundant adsorption sites and stability. BC@γ-Fe2O3 provides an efficient and green insight into the simultaneous removal of complex heavy metals with promising application in wastewater treatment.

Remediation of Cr(VI) contaminated soil by chitosan stabilized FeS composite and the changes in microorganism community

In-suit immobilization is one of the major strategies to remediate heavy metals contaminated soil with the effectiveness largely depends on the characteristics of the added chemical reagents/materials. In this study, chitosan stabilized FeS composite (CS-FeS) was prepared to evaluate the performance of remediating the high and toxic hexavalent chromium contaminated soil from the effectiveness and microbial response aspects. The characterization analysis confirmed the successful preparation of composite, and the introduction of chitosan successfully stabilized FeS to protect it from rapid oxidation as compared to bare FeS particles. With the addition dosage at 0.1%, about 85.6% and 81.3% of Cr(VI) was reduced in 3 d based on toxicity characteristic leaching procedure (TCLP) and CaCl₂ extraction, and the reduction efficiency increased to 96.6% and 94.8% in 7 d, respectively. The Cr(VI) was non-detected in the TCLP leachates with increase the CS-FeS composites to 0.5%. The percentages of HOAc-extractable Cr decreased from 25.17% to 6.12% accompanied with the increase in the residual Cr from 4.26% to 13.77% and improvement of soil enzyme activity under CS-FeS composites addition. Cr(VI) contamination reduced the diversity of microbial community in soil. Three dominate prokaryotic microorganisms, namely Proteobacteria, Actinobacteria and Firmicutes, were observed in Cr-contaminated soil. The addition of CS-FeS composites increased the microbial diversity especially for that in relative lower abundance. The relative abundance of Proteobacteria and Firmicute related to Cr-tolerance and reduction increased in CS-FeS composites added soils. Taking together, these results demonstrated the potential and promising of using the CS-FeS composites for Cr(VI) polluted soil remediation.

Microbial functionalities and immobilization of environmental lead: Biogeochemical and molecular mechanisms and implications for bioremediation

The increasing environmental and human health concerns about lead in the environment have stimulated scientists to search for microbial processes as innovative bioremediation strategies for a suite of different contaminated media. In this paper, we provide a compressive synthesis of existing research on microbial mediated biogeochemical processes that transform lead into recalcitrant precipitates of phosphate, sulfide, and carbonate, in a genetic, metabolic, and systematics context as they relate to application in both laboratory and field immobilization of environmental lead. Specifically, we focus on microbial functionalities of phosphate solubilization, sulfate reduction, and carbonate synthesis related to their respective mechanisms that immobilize lead through biomineralization and biosorption. The contributions of specific microbes, both single isolates or consortia, to actual or potential applications in environmental remediation are discussed. While many of the approaches are successful under carefully controlled laboratory conditions, field application requires optimization for a host of variables, including microbial competitiveness, soil physical and chemical parameters, metal concentrations, and co-contaminants. This review challenges the reader to consider bioremediation approaches that maximize microbial competitiveness, metabolism, and the associated molecular mechanisms for future engineering applications. Ultimately, we outline important research directions to bridge future scientific research activities with practical applications for bioremediation of lead and other toxic metals in environmental systems.

Application of a novel Ca-Fe-Si-S composite for the synchronous stabilization of As, Zn, Cu, and Cd in acidic arsenic slag

The control of multiple heavy metals (HMs) pollution in solid wastes, especially the co-contamination of As and other heavy metal cations, is of great importance to ecological and environmental health. To address this problem, the preparation and application of multifunctional materials have attracted wide attention. In this work, a novel Ca-Fe-Si-S composite (CFSS) was applied to stabilize As, Zn, Cu, and Cd in acid arsenic slag (ASS). The CFSS exhibited synchronous stabilization ability for As, Zn, Cu, Cd and owned strong acid neutralization capacity. Under simulated field conditions, the acid rain extracted HMs in ASS successfully decreased below the emission standard (GB 3838-2002-IV category in China) after incubated by 5% CFSS for 90 days. Meanwhile, the application of CFSS promoted the transformation of leachable HMs into less accessible forms, which was conductive to the long-term stabilization for HMs. There was competitive relation among the three heavy metal cations, following the stabilization sequence of Cu > Zn > Cd during incubation. And the stabilization mechanisms of HMs by CFSS were proposed as chemical precipitation, surface complexation, and ion/anion exchange. The research will be greatly conducive to the remediation and governance of field multiple HMs contaminated sites.

Arsenic removal from aqueous solution: A comprehensive synthesis with meta-data

Removal of arsenic from drinking water is one of the most important global concerns. Among the various techniques, adsorptive removal of arsenic is considered as a viable most effective method. However, limited attention is given to understand the overall relative sorption capacity of different sorbents (e.g., biocomposite, biochar and nano-composite etc.) since various factors influence the sorption capacity. The aim of this study is to assess the effectiveness of various adsorbents with quantitative estimation (Langmuir adsorption maxima, Qmax) as well as to evaluate the influence of experimental conditions on the achievement of maximum adsorption. A number of analyses including meta-analysis, analysis of variance (ANOVA), scientometric and regression were performed. The results revealed that among the sorbents, nanoparticles show the greatest sorption capacity while pre-doped biochar performed the best among different biochars. Average across all sorbents, As (V) removal efficacy was higher than As (III). As expected, a high point of zero charge (PZC) and higher positive surface charge favored adsorption. The relative contribution of different mechanisms was also discussed. Our scientometric analyses revealed that, research should focus on the development of low-cost adsorbents and increase their reusability, safe disposal of adsorbed arsenic. Altogether, our findings provide a molecular understanding of arsenic sorption to different sorbents with implications for tailoring a good sorbent for arsenic removal from drinking water.

In situ preparation of a multifunctional adsorbent by optimizing the Fe2+/Fe3+/Mn2+/HA ratio for simultaneous and efficient removal of Cd(II), Pb(II), Cu(II), Zn(II), As(III), Sb(III), As(V) and Sb(V) from aqueous environment: Behaviors and mechanisms

Multiple potentially toxic elements (PTEs) often coexist in practical wastewater environment, which poses serious risks to the ecological environment and human health. However, few of the reported adsorbents are capable of simultaneously and effectively removing multiple PTEs from wastewater due to the unique properties of each element. In this work, a multifunctional adsorbent FMHs was developed by optimizing Fe²⁺/Fe³⁺/Mn²⁺/HA ratio, and applied to remove Cd(II), Pb(II), Cu(II), Zn(II), As(III), Sb(III), As(V) and Sb(V) from aqueous solution. Results revealed that the adsorption data obeyed the Elovich, Sips and Redlich-Peterson models in the mono-component system, and the maximum adsorption capacity of FMHs was superior to most adsorbents reported in the literatures. In addition, FMHs retained considerable removal capacity after four cycles, and maintained excellent adsorption performance under the interference of different environmental factors (including pH, ionic strength, co-existing ions and humic acid). In the multi-component system, FMHs also presented high adsorption capacity for all the selected PTEs, especially for Sb(III/V) and Pb(II). Characterization results confirmed that various removal mechanisms, such as precipitation, surface complexation, ion exchange, electrostatic attraction and redox, were responsible for the capture of PTEs by FMHs.

Valorization of agriculture waste biomass as biochar: As first-rate biosorbent for remediation of contaminated soil

Each year, Asia produces an estimated 350 million tonnes of agricultural residues. According to Ministry of Power projections, numerous tonnes of such waste are discarded each year, in addition to being used as green manure. The methodology used to convert agricultural waste into the most valuable biochar, as well as its critical physical and chemical properties, were described in this review. This review also investigates the beneficial effects of bio and phytoremediation on metal(lloid)-contaminated soil. Agriculture biomass-based biochar is an intriguing organic residue material with the potential to be used as a responsible solution for metal(lloid) polluted soil remediation and soil improvement. Plants with faster growth and higher biomass can meet massive remediation demands. Recent research shows significant progress in agricultural biomass-based biomass conversion as biochar, as well as understanding the frameworks of metal(lloid) accumulation and mobility in plants used for metal(lloid) polluted soil remediation. Biochar made from various agricultural biomass can promote native plant growth and improve phytoremediation efficiency in polluted soil with metal(lloid)s. This carbon-enriched biochar promotes native microbial activity by neutralising pH and providing adequate nutrition. Thus, this review critically examines the feasibility of converting agricultural waste biomass into biochar, as well as the impact on plant and microbe remediation potential in metal(lloid)s polluted soil.

Effects of Inorganic Passivators on Gas Production and Heavy Metal Passivation Performance during Anaerobic Digestion of Pig Manure and Corn Straw

The treatment of livestock manure caused by the expansion of the breeding industry in China has attracted wide attention. Heavy metals in pig manure can pollute soil and water and even transfer to crops, posing harm to humans through the food chain. In this study, corn straw was selected as the additive and introduced into the anaerobic digestion. Sepiolite (SE), ferric oxide (Fe₂O₃), attapulgite (AT) and ferric sulfate (FeSO₄) were used as passivators to compare the effects of these inorganic passivators on gas production and passivation of heavy metals during the process of the anaerobic digestion. When the dry mass ratio of pig manure to straw is 8:2, the gas production efficiency is optimal. SE, AT and ferric sulfate have a much stronger ability to improve gas production performance than Fe₂O₃. The total gas production increased by 10.34%, 6.62% and 4.56%, and the average methane production concentration increased by 0.7%, 0.3% and 0.4%, respectively. The influence of SE, AT and ferric sulfate on the passivation of heavy metals is much better than Fe₂O₃, and the fractions in biological effective forms of Cu and Zn reduced by 41.87 and 19.32%, respectively. The anaerobic digestion of mixed materials is conducive to the gas production and the passivation of heavy metals. Therefore, SE, AT and ferric sulfate are selected as composite passivators, and the optimal ratio of inorganic composite passivators i: AT 7.5 g/L, ferric sulfate 5 g/L and SE 7.5 g/L, according to the results of orthogonal experiments. This study can provide a theoretical basis for the safe application of biogas fertilizers.

Simultaneous and efficient removal of multiple heavy metal(loid)s from aqueous solutions using Fe/Mn (hydr)oxide and phosphate mineral composites synthesized by regulating the proportion of Fe(II), Fe(III), Mn(II) and PO43

In this work, a novel adsorbent FMPs consisting of Fe/Mn (hydr)oxides and phosphate minerals was synthesized by regulating the proportion of Fe(II), Fe(III), Mn(II) and PO₄^3-, and its removal behaviors and possible mechanisms for Cd(II), Pb(II), Cu(II), Zn(II), As(III), Sb(III), As(V) and Sb(V) were systematically investigated. Batch adsorption experiments revealed that the adsorption process of FMPs to these metal(loid) ions conformed to pseudo-second-order (R² > 0.99) and Redlich-Peterson (R² > 0.94) models in the mono-component system, demonstrating a hybrid chemical reaction-adsorption process. In addition, the solution pH and ionic strength could affect the adsorption capacity of FMPs to heavy metal(loid)s with varying degrees. Besides, FMPs presented feasible stability and reusability even after four cycles. Combining the macroscopic and microscopic characteristics, the adsorption mechanisms of FMPs mainly included surface complexation, electrostatic adsorption, inner-sphere complexation, hydrogen bonding, redox and pore-filling. In a multi-component system, FMPs exhibited an excellent affinity for capturing Pb(II) and Sb(III/V). This work provides an alternative method for designing and developing a series of novel adsorbent in removing multiple heavy metal(loid)s from wastewater, and demonstrated its application prospect in the remediation of multi-metal(loid) composite polluted water.

Potentiality of phosphorus-accumulating organisms biomasses in biosorption of Cd(II), Pb(II), Cu(II) and Zn(II) from aqueous solutions: Behaviors and mechanisms

Heavy metal pollution is consistently a critical global issue, and bioremediation is regarded as one of the most promising approaches. In this work, the biosorption characteristics of Cd(II), Pb(II), Cu(II) and Zn(II) from aqueous solutions using three phosphorus-accumulating organisms (PAOs) biomasses, Ochrobactrum cicero (PAB-006), Stenotrophomonas maltophilia (PAB-009), and Pseudomonas putida (PAB-0031), as biosorbents were investigated. Results indicated that the equilibrium biosorption capacities of biosorbents to heavy metal ions were sensitive to the solution pH, and increased with increasing pH values. The experimental data of Cd(II), Pb(II), Cu(II) and Zn(II) biosorption were in good agreement with the Pseudo-second-order, Redlich-Peterson and Temkin models, implying that the biosorption was a hybrid chemical reaction-biosorption process. In addition, the theoretical maximum biosorption capacities of Cd(II), Pb(II), Cu(II) and Zn(II) were calculated to be 67.84, 80.23, 50.56 and 63.07 mg/g for PAB-006, 59.99, 87.71, 39.26 and 64.00 mg/g for PAB-009 and 68.31, 85.43, 38.97 and 62.85 mg/g for PAB-031, respectively (pH = 5.0 ± 0.1, T = 25 °C), according to the parameters of the Langmuir model. Moreover, ionic strength had negligible influences or slight promoting effects, while humic acid exhibited positive effects on the removal of heavy metals. Further, PABs were stable and displayed excellent reusability. Characterization techniques of FTIR and XPS revealed that surface complexation, ion exchange, hydrogen bonding and electrostatic interaction were the main mechanisms involved in the biosorption process. In summary, the biosorbent PABs possessed high biosorption performance with excellent reusability, and which hold the great application prospect in the treatment of heavy metal contaminated water.