Probing the surface of oxidized carbon nanotubes by selective interaction with target molecules

Monofunctional pyrenes at carbon nanotube electrodes for direct electron transfer H2O2 reduction with HRP and HRP-bacterial nanocellulose

The non-covalent modification of carbon nanotube electrodes with pyrene derivatives is a versatile approach to enhance the electrical wiring of enzymes for biosensors and biofuel cells. We report here a comparative study of five pyrene derivatives adsorbed at multi-walled carbon nanotube electrodes to shed light on their ability to promote direct electron transfer with horseradish peroxidase (HRP) for H₂O₂ reduction. In all cases, pyrene-modified electrodes enhanced catalytic reduction compared to the unmodified electrodes. The pyrene N-hydroxysuccinimide (NHS) ester derivative provided access to the highest catalytic current of 1.4 mA cm^-2 at 6 mmol L^-1 H₂O₂, high onset potential of 0.61 V vs. Ag/AgCl, insensitivity to parasitic H₂O₂ oxidation, and a large linear dynamic range that benefits from insensitivity to HRP "suicide inactivation" at 4-6 mmol L^-1 H₂O₂. Pyrene-aliphatic carboxylic acid groups offer better sensor sensitivity and higher catalytic currents at ≤ 1 mmol L^-1 H₂O₂ concentrations. The butyric acid and NHS ester derivatives gave high analytical sensitivities of 5.63 A M^-1 cm^-2 and 2.96 A M^-1 cm^-2, respectively, over a wide range (0.25-4 mmol^-1) compared to existing carbon-based HRP biosensor electrodes. A bacterial nanocellulose pyrene-NHS HRP bioelectrode was subsequently elaborated via "one-pot" and "layer-by-layer" strategies. The optimised bioelectrode exhibited slightly weaker voltage output, further enhanced catalytic currents, and a major enhancement in 1-week stability with 67% activity remaining compared to 39% at the equivalent electrode without nanocellulose, thus offering excellent prospects for biosensing and biofuel cell applications.

Sonochemical modification of carbon nanotubes for enhanced nanocomposite performance

Multi-walled carbon nanotubes (CNTs) have been treated using 20kHz ultrasound in combination with dilute nitric and sulfuric acids at much lower concentrations than previously reported. The measurements revealed an optimum set of sonication conditions (in this case 30min at 12Wcm^-2) exists to overcome aggregation of the nanotubes and to allow efficient dispersion in ethanol or in chitosan. Transmission electron microscopy and Raman spectroscopy suggested the removal of amorphous material and reduction of the CNT diameter as well as modifications to their defect structures. The surface oxidation was determined by FTIR spectroscopy. At longer times or higher ultrasound intensities, degradation such as nanotube shortening and additional defect generation in the graphitic network occurred and the benefits of using ultrasound decreased. The modified CNTs were used as fillers for chitosan films and gave a tenfold increase in tensile strength and integrity of the films. The methodology was combined with sonochemical generation of gold or iron oxide nanoparticles to produce a range of functional membranes for catalytic reductive hydrogenation or dye degradation under conditions that are more environmentally benign than those previously used. Our results further add to the usefulness of sonochemistry as a valuable tool in preparative materials chemistry but also illustrate the crucial importance of careful control over the experimental conditions if optimum results are to be obtained.

β-Cyclodextrin carbon nanotube-enhanced sensor for ciprofloxacin detection

A simple and expedite electrochemical methodology was developed for the determination of ciprofloxacin, based on a glassy carbon (GC) electrode modified by a combination of multi-walled carbon nanotubes (MWCNT) with β-cyclodextrin (β-CD) incorporated in a polyaniline film. The combined use of β-CD and MWCNT in the electrochemical sensor leads to a significant signal improvement. The β-CD/MWCNT modified GC electrode exhibited efficient electrocatalytic behavior in the oxidation of ciprofloxacin with relatively high sensitivity, stability and lifetime. Molecular modeling studies showed that ciprofloxacin binds preferably to β-CD rather than to CNT edges, leading to an improved sensitivity of the sensor. Under optimized conditions, a linear calibration curve was obtained for ciprofloxacin in the concentration range 10-80 µM with a detection limit of 50 nM. The analytical performance of this sensor was evaluated for the detection of ciprofloxacin in a wastewater treatment plant effluent.