Isothermal microcalorimetry - A quantitative method to monitor Trypanosoma congolense growth and growth inhibition by trypanocidal drugs in real time

Simple Growth–Metabolism Relations Are Revealed by Conserved Patterns of Heat Flow from Cultured Microorganisms

Quantitative analyses of cell replication address the connection between metabolism and growth. Various growth models approximate time-dependent cell numbers in culture media, but physiological implications of the parametrizations are vague. In contrast, isothermal microcalorimetry (IMC) measures with unprecedented sensitivity the heat (enthalpy) release via chemical turnover in metabolizing cells. Hence, the metabolic activity can be studied independently of modeling the time-dependence of cell numbers. Unexpectedly, IMC traces of various origins exhibit conserved patterns when expressed in the enthalpy domain rather than the time domain, as exemplified by cultures of Lactococcus lactis (prokaryote), Trypanosoma congolese (protozoan) and non-growing Brassica napus (plant) cells. The data comply extraordinarily well with a dynamic Langmuir adsorption reaction model of nutrient uptake and catalytic turnover generalized here to the non-constancy of catalytic capacity. Formal relations to Michaelis–Menten kinetics and common analytical growth models are briefly discussed. The proposed formalism reproduces the “life span” of cultured microorganisms from exponential growth to metabolic decline by a succession of distinct metabolic phases following remarkably simple nutrient–metabolism relations. The analysis enables the development of advanced enzyme network models of unbalanced growth and has fundamental consequences for the derivation of toxicity measures and the transferability of metabolic activity data between laboratories.

Efficacy of Experimental Mouth Rinses on Caries-Related Biofilms in vitro

This study assessed the efficacy of tin and Polyethylenglycol (PEG-3) tallow aminopropylamine in different concentrations on Streptococcus mutans (S. mutans) biofilms to establish a new screening process for different antimicrobial agents and to gain more information on the antibacterial effects of these agents on cariogenic biofilms. Isothermal microcalorimetry (IMC) was used to determine differences in two growth parameters: lag time and growth rate; additionally, reduction in active biofilms was calculated. Experimental mouth rinses with 400 and 800 ppm tin derived from stannous fluoride (SnF₂) revealed results (43.4 and 49.9% active biofilm reduction, respectively) similar to meridol mouth rinse (400 ppm tin combined with 1,567 ppm PEG-3 tallow aminopropylamine; 55.3% active biofilm reduction) (p > 0.05), while no growth of S. mutans biofilms was detected during 72 h for samples treated with an experimental rinse containing 1,600 ppm tin (100% active biofilm reduction). Only the highest concentration (12,536 ppm) of rinses containing PEG-3 tallow aminopropylamine derived from amine fluoride (AmF) revealed comparable results to meridol (57.5% reduction in active biofilm). Lower concentrations of PEG-3 tallow aminopropylamine showed reductions of 16.9% for 3,134 ppm and 33.5% for 6,268 ppm. Maximum growth rate was significantly lower for all the samples containing SnF₂ than for the samples containing control biofilms (p < 0.05); no differences were found between the control and all the PEG-3 tallow aminopropylamine (p > 0.05). The growth parameters showed high reproducibility rates within the treated groups of biofilms and for the controls; thus, the screening method provided reliable results.

Antiprotozoal Structure-Activity Relationships of Synthetic Leucinostatin Derivatives and Elucidation of their Mode of Action

Leucinostatin A is one of the most potent antiprotozoal compounds ever described, but little was known on structure-activity relationships (SAR). We used Trypanosoma brucei as a protozoal model organism to test synthetically modified derivatives, resulting in simplified but equally active compounds 2 (ZHAWOC6025) and 4 (ZHAWOC6027), which were subsequently modified in all regions of the molecule to gain an in-depth SAR understanding. The antiprotozoal SAR matched SAR in phospholipid liposomes, where membrane integrity, leaking, and dynamics were studied. The mode of action is discussed based on a structure-activity analysis of derivatives in efficacy, ultrastructural studies in T. brucei, and artificial membrane models, mimicking membrane stability and membrane potential. The main site of antiprotozoal action of natural and synthetic leucinostatins lies in the destabilization of the inner mitochondrial membrane, as demonstrated by ultrastructural analysis, electron microscopy and mitochondrial staining. Long-time sublethal exposure of T. brucei (200 passages) and siRNA screening of 12'000 mutants showed no signs of resistance development to the synthetic derivatives.

Non-invasive monitoring of drug action: A new live in vitro assay design for Chagas' disease drug discovery

New assay designs are needed to improve the predictive value of the Trypanosoma cruzi in vitro tests used as part of the Chagas' disease drug development pipeline. Here, we employed a green fluorescent protein (eGFP)-expressing parasite line and live high-content imaging to monitor the growth of T. cruzi amastigotes in mouse embryonic fibroblasts. A novel assay design allowed us to follow parasite numbers over 6 days, in four-hour intervals, while occupying the microscope for only 24 hours per biological replicate. Dose-response curves were calculated for each time point after addition of test compounds, revealing how EC50 values first decreased over the time of drug exposure, and then leveled off. However, we observed that parasite numbers could vary, even in the untreated controls, and at different sites in the same well, which caused variability in the EC50 values. To overcome this, we established that fold change in parasite number per hour is a more robust and informative measure of drug activity. This was calculated based on an exponential growth model for every biological sample. The net fold change per hour is the result of parasite replication, differentiation, and death. The calculation of this fold change enabled us to determine the tipping point of drug action, i.e. the time point when the death rate of the parasites exceeded the growth rate and the fold change dropped below 1, depending on the drug concentration and exposure time. This revealed specific pharmacodynamic profiles of the benchmark drugs benznidazole and posaconazole.

Chagas' disease, caused by Trypanosoma cruzi, is a chronic debilitating infection occurring mostly in Latin America. There is an urgent need for new, well tolerated drugs. However, the latest therapeutic candidates have yielded disappointing outcomes in clinical trials, despite promising preclinical results. This demands new and more predictive in vitro assays. To address this, we have developed an assay design that enables the growth of T. cruzi intracellular forms to be monitored in real time, under drug pressure, for 6 days post-infection. This allowed us to establish the tipping point of drug action, when the death rate of the parasites exceeded the growth rate. The resulting pharmacodynamics profiles can provide robust and informative details on anti-chagasic candidates, as demonstrated for the benchmark drugs benznidazole and posaconazole.

In Vitro Drug Efficacy Testing Against Trypanosoma brucei

The recent endorsement of fexinidazole by the European Medicines Agency for the treatment of human African trypanosomiasis has demonstrated the high predictive value of cell-based assays for parasite chemotherapy. Here we describe three in vitro drug susceptibility tests with Trypanosoma brucei that have served as the basis for the identification of fexinidazole as a promising lead: (1) a standard assay with end-point measurement to determine drug efficacy; (2) a wash-out assay to test for reversibility and speed of drug action; (3) isothermal microcalorimetry for real-time measurement of onset of drug action and time to kill. Together, these assays allow to estimate pharmacodynamic parameters in vitro and to devise appropriate treatment regimens for subsequent in vivo experiments.

Rapid Calorimetric Detection of Bacterial Contamination: Influence of the Cultivation Technique

Modern isothermal microcalorimeters (IMC) are able to detect the metabolic heat of bacteria with an accuracy sufficient to recognize even the smallest traces of bacterial contamination of water, food, and medical samples. The modern IMC techniques are often superior to conventional detection methods in terms of the detection time, reliability, labor, and technical effort. What is missing is a systematic analysis of the influence of the cultivation conditions on calorimetric detection. For the acceptance of IMC techniques, it is advantageous if already standardized cultivation techniques can be combined with calorimetry. Here we performed such a systematic analysis using Lactobacillus plantarum as a model bacterium. Independent of the cultivation techniques, IMC detections were much faster for high bacterial concentrations (>102 CFU⋅mL-1) than visual detections. At low bacterial concentrations (<102 CFU⋅mL-1), detection times were approximately the same. Our data demonstrate that all kinds of traditional cultivation techniques like growth on agar (GOA) or in agar (GIA), in liquid media (GL) or on agar after enrichment via membrane filtration (GF) can be combined with IMC. The order of the detection times was GF < GIA ≈ GL ≈ GOA. The observed linear relationship between the calorimetric detection times and the initial bacterial concentrations can be used to quantify the bacterial contamination. Further investigations regarding the correlation between the filling level (in mm) of the calorimetric vessel and the specific maximum heat flow (in μW⋅g-1) illustrated two completely different results for liquid and solid media. Due to the better availability of substrates and the homogeneous distribution of bacteria growing in a liquid medium, the volume-related maximum heat flow was independent on the filling level of the calorimetric vessels. However, in a solid medium, the volume-related maximum heat flow approached a threshold and achieved a maximum at low filling levels. This fundamentally different behavior can be explained by the spatial limitation of the growth of bacterial colonies and the reduced substrate supply due to diffusion.