Bandgap tuning in SrTi(N,O,F)3 by anionic-lattice variation

Study on the mechanism of acid treatment La0.8Sr0.2Mn0.8Cu0.2O3 to improve the catalytic activity of formaldehyde at low temperature

To address the issue of surface enrichment of A-site ions in perovskite and the resulting suppression of catalytic activity, the La0.8Sr0.2Mn0.8Cu0.2O3 was modified by treatment with dilute nitric acid (2 mol/L) and dilute acetic acid (2 mol/L). The results show that the effect of dilute nitric acid treatment on the morphology and catalytic activity of the catalyst is more significant. The specific surface area of the catalyst after dilute nitric acid treatment (268.78 m2/g) is seven times higher than before treatment (37.55 m2/g). The low-temperature catalytic oxidation activity of HCHO of the catalyst after dilute nitric acid treatment is significantly improved, achieving a 50% HCHO oxidation efficiency at 80 °C, while the original sample requires 127 °C to achieve a 50% HCHO conversion. The excellent catalytic activity of the catalyst after dilute nitric acid treatment is related to its large specific surface area, high surface-active site density, and abundant Mn4+ ions. Stability and water resistance experiments show that the catalyst after dilute nitric acid treatment has excellent reaction stability and good water resistance ability. The mechanism of the formaldehyde oxidation reaction is that formaldehyde is first oxidized to a dioxymethylene (DOM) intermediate and DOM dehydrogenation reaction is responsible for the formation of formate species (HCOO-).

Band Gap Adjustment in Perovskite-type Eu1−x Ca x TiO3 via Ammonolysis

Perovskite-type oxynitrides AB(O,N)3 are potential candidates for photoelectrode materials in solar water splitting. A drawback of these materials is their low sintering tendency resulting in low electrical conductivities. Typically, they are prepared by ammonia treatment of insulating, wide band gap oxides. In this study, we propose an approach starting from small band gap oxides Eu1−x Ca x TiO3− δ and then widen the band gaps in a controlled way by ammonolysis and partial Ca2+ substitution. Both together induced a distortion of the octahedral network and dilution of the Eu4f and N2p levels in the valence band. The effect is the stronger the more Ca2+ is present. Within the series of samples, Eu0.4Ca0.6Ti(O,N)3 had the most suitable optical band gap (EG ≈ 2.2 eV) for water oxidation. However, its higher Eu content compared to Eu0.1Ca0.9Ti(O,N)3 slowed down the charge carrier dynamics due to enhanced trapping and recombination as expressed by large accumulation (τ on) and decay (τ off) times of the photovoltage of up to 109 s and 486 s, respectively. In contrast, the highly Ca2+-substituted samples (x ≥ 0.7) were more prone to formation of TiN and oxygen vacancies also leading to Ti3+ donor levels below the conduction band. Therefore, a precise control of the ammonolysis temperature is essential, since even small amounts of TiN can suppress the photovoltage generation by fast recombination processes. Water oxidation tests on Eu0.4Ca0.6Ti(O,N)3 revealed a formation of 7.5 μmol O2 from 50 mg powder together with significant photocorrosion of the bare material. Combining crystal structure, chemical composition, and optical and electronical band gap data, a first simplified model of the electronical band structure of Eu1−x Ca x Ti(O,N)3 could be proposed.

Removal of VOCs from gas streams with double perovskite-type catalysts

Double perovskite-type catalysts including La₂CoMnO₆ and La₂CuMnO₆ are first evaluated for the effectiveness in removing volatile organic compounds (VOCs), and single perovskites (LaCoO₃, LaMnO₃, and LaCuO₃) are also tested for comparison. All perovskites are tested with the gas hourly space velocity (GHSV) of 30,000hr^-1, and the temperature range of 100-600°C for C₇H₈ removal. Experimental results indicate that double perovskites have better activity if compared with single perovskites. Especially, toluene (C₇H₈) can be completely oxidized to CO₂ at 300°C as La₂CoMnO₆ is applied. Characterization of catalysts indicates that double perovskites own unique surface properties and are of higher amounts of lattice oxygen, leading to higher activity. Additionally, apparent activation energy of 68kJ/mol is calculated using Mars-van Krevelen model for C₇H₈ oxidation with La₂CoMnO₆ as catalyst. For durability test, both La₂CoMnO₆ and La₂CuMnO₆ maintain high C₇H₈ removal efficiencies of 100% and 98%, respectively, at 300°C and 30,000hr^-1, and they also show good resistance to CO₂ (5%) and H₂O_(g) (5%) of the gas streams tested. For various VOCs including isopropyl alcohol (C₃H₈O), ethanal (C₂H₄O), and ethylene (C₂H₄) tested, as high as 100% efficiency could be achieved with double perovskite-type catalysts operated at 300-350°C, indicating that double perovskites are promising catalysts for VOCs removal.

Glimpses of the modification of perovskite with graphene-analogous materials in photocatalytic applications

This review highlights the recent trends in the modification of perovskite with graphene-analogous materials towards H₂production and pollutant degradation.