Non-destructive laser-ultrasonic Synthetic Aperture Focusing Technique (SAFT) for 3D visualization of defects

Research on the 3D Reverse Time Migration Technique for Internal Defects Imaging and Sensor Settings of Pressure Pipelines

Although pressure pipelines serve as a secure and energy-efficient means of transporting oil, gas, and chemicals, they are susceptible to fatigue cracks over extended periods of cyclic loading due to the challenging operational conditions. Their quality and efficiency directly affect the safe operation of the project. Therefore, a thorough and precise characterization approach towards pressure pipelines can proactively mitigate safety risks and yield substantial economic and societal benefits. At present, the current mainstream 2D ultrasound imaging technology faces challenges in fully visualizing the internal defects and topography of pressure pipelines. Reverse time migration (RTM), widely employed in geophysical exploration, has the capability to visualize intricate geological structures. In this paper, we introduced the RTM into the realm of ultrasonic non-destructive testing, and proposed a 3D ultrasonic RTM imaging method for internal defects and sensor settings of pressure pipelines. To accurately simulate the extrapolation of wave field in 3D pressure pipelines, we set the absorbing boundary and double free boundary in cylindrical coordinates. Subsequently, using the 3D ultrasonic RTM approach, we attained higher-precision 3D imaging of internal defects in the pressure pipelines through suppressing imaging artifacts. By comparing and analyzing the imaging results of different sensor settings, the design of the observation system is optimized to provide a basis for the imaging and interpretation of actual data. Both simulations and actual field data demonstrate that our approach delivers top-notch 3D imaging of pipeline defects (with an imaging range accuracy up to 97.85%). This method takes into consideration the complexities of multiple scattering and mode conversions occurring at the base of the defects as well as the optimal sensor settings.

Suppressing artifacts in the total focusing method using the directivity of laser ultrasound

Based on a synthesized laser ultrasonic array, full matrix capture can be used to acquire data, which can then be post-processed using the total focusing method. However, this noncontact ultrasonic imaging technique has not been widely used because of the numerous artifacts in ultrasonic images and time-consuming data acquisition. To address these issues, this study proposes a post-processing algorithm, which uses the laser ultrasound directivity information to suppress the artifacts in the total focusing method's images. In particular, a weight factor is defined using the directivity information. By multiplying the image intensity of the total focusing method with this factor, the algorithm uses not only the amplitude and phase information of laser ultrasound but also its directivity information. The experimental results indicate that four types of artifacts are suppressed. Because the grating lobe artifacts can be suppressed, a larger element spacing can be used to reduce the data acquisition time.

Influence of optical transmissivity on signal characteristics of photoacoustic guided waves in long cortical bone

Long cortical bone allows axial transmission of ultrasonic guided waves, which has been utilized for osteoporosis evaluation. Benefiting structural and molecular sensitivity, photoacoustic has been used for tissue composition characterization. However, photoacoustic guided waves (PAGWs) in long cortical bone as well as the influence of optical transmissivity on PAGWs have not been thoroughly investigated. In the study, the influence of optical transmissivity on the signal characteristics of PAGWs was experimentally studied with a 1064 nm pulsed laser ultrasonic system and a tunable laser system (wavelength range: 650-2600 nm). Results show that dispersion curves of PAGWs are not significantly affected by the optical transmissivity; while photoacoustic guided modes and signal spectrum are sensitive to the optical transmissivity in cortical bone. In experiments, the lasers with high transmissivity can emit pure A₀ mode PAGWs at the low frequency, around 22 kHz, in the relatively thick 6.2 mm bone plate; on the contrary, both A₀ and S₀ modes are generated. The slope of power spectrum density (PSD) of PAGWs decreases with the increase of transmissivity, and the decline rate is around -0.229. The study proves the correlation between the signal characteristics of PAGWs and the optical transmissivity, it is helpful for the development of PAGWs in long cortical bone towards the osteoporosis evaluation.

Multi-mode laser-ultrasound imaging using Time-domain Synthetic Aperture Focusing Technique (T-SAFT)

The Synthetic Aperture Focusing Technique (SAFT) is an imaging algorithm used in laser ultrasonics (LU) to visualise the appearance of defects. However, ultrasound excited by a pulsed laser has the characteristics of wide bandwidth and multi-mode directivity patterns, leading to common problems in the SAFT process, such as low utilisation of ultrasound information and possible artefacts. To solve these problems, a Multi-mode Time-domain SAFT (MMT-SAFT) algorithm is proposed in this paper. The influence of ultrasonic directivity is discussed according to the imaging depth range, and imaging with multiple LU modes is performed to reduce artefacts. Simulations and experimental results prove the feasibility of the MMT-SAFT algorithm, which not only presents a clearer image of the upper part of defects but also improves image quality compared with time-domain SAFT using a single ultrasonic mode. The proposed technique can provide feasible directions for laser ultrasonic defect imaging.