Ice-Crystal-Templated "Accordion-Like" Cellulose Nanofiber/MXene Composite Aerogels for Sensitive Wearable Pressure Sensors

Hydrophobic modification of cellulose nanofibers by gallic acid and the application in pressure sensing

Via rational molecular structure design and using gallic acid (GA) for hydrophobic modification of cellulose nanofibers (CNF), the "polymer dipole" CNF-GA with hydrophilic main chains and hydrophobic side chains was prepared, which improved the poor piezoelectric properties of CNF used for preparing pressure sensors. Due to the appearance of the side chains, the elongation at break of the CNF-GA-2, compared with CNF, was enhanced by 186 %, and the excellent tensile strength, puncture load, and tearing strength were displayed. Moreover, the significant glass transition temperature (Tg) near the human body temperature was exhibited for CNF-GA, making it possible to be applied in temperature sensing. Most importantly, the CNF-GA-2 showed the maximum hydrophobicity, with a contact angle of 76.77°. Finally, the CNF-GA-2/MXene nanocomposite film was prepared by the CNF-GA-2 with MXene through vacuum filtration. The results indicated that the film had excellent piezoelectric properties (d33 = 63.283), the generated stable induced voltage (125.6 mV), the preferable piezoresistive performance (ΔR/R0 = 2.15), the fast response/recovery time (48/61 ms), which could achieve dynamic and static responses. Moreover, this film could be used for real-time detection of limb movements (such as wrists).

Highly sensitive, wide-pressure and low-frequency characterized pressure sensor based on piezoresistive-piezoelectric coupling effects in porous wood

Lightweight and highly compressible materials have received considerable attention in flexible pressure sensing devices. In this study, a series of porous woods (PWs) are produced by chemical removal of lignin and hemicellulose from natural wood by tuning treatment time from 0 to 15 h and extra oxidation through H₂O₂. The prepared PWs with apparent densities varying from 95.9 to 46.16 mg/cm³ tend to form a wave-shaped interwoven structure with improved compressibility (up to 91.89 % strain under 100 kPa). The sensor assembled from PW with treatment time of 12 h (PW-12) exhibits the optimal piezoresistive-piezoelectric coupling sensing properties. For the piezoresistive properties, it has high stress sensitivity of 15.14 kPa^-1, covering a wide linear working pressure range of 0.06-100 kPa. For its piezoelectric potential, PW-12 shows a sensitivity of 0.443 V·kPa^-1 with ultralow frequency detection as low as 0.0028 Hz, and good cyclability over 60,000 cycles under 0.41 Hz. The nature-derived all-wood pressure sensor shows obvious superiority in the flexibility for power supply requirement. More importantly, it presents fully decoupled signals without cross-talks in the dual-sensing functionality. Sensor like this is capable of monitoring various dynamic human motions, making it an extremely promising candidate for the next generation artificial intelligence products.

Fabrication, Performance, and Potential Applications of MXene Composite Aerogels

Aerogel, known as one of the remarkable materials in the 21st century, possesses exceptional characteristics such as high specific surface area, porosity, and elasticity, making it suitable for a diverse range of applications. In recent years, MXene-based aerogels and MXene composite aerogels as functional materials have solved some limitations of traditional aerogels, such as improving the electrical conductivity of biomass and silicon aerogels, further improving the energy storage capacity of carbon aerogels, enhancing polymer-based aerogels, etc. Consequently, extensive research efforts have been dedicated to investigating MXene-based aerogels, positioning them at the forefront of material science studies. This paper provides a comprehensive review of recent advancements in the preparation, properties, and applications of MXene-based composite aerogels. The primary construction strategies employed (including direct synthesis from MXene dispersions and incorporation of MXene within existing substrates) for fabricating MXene-based aerogels are summarized. Furthermore, the desirable properties (including their applications in electrochemistry, electromagnetic shielding, sensing, and adsorption) of MXene composite aerogels are highlighted. This paper delves into a detailed discussion on the fundamental properties of composite aerogel systems, elucidating the intricate structure-property relationships. Finally, an outlook is provided on the opportunities and challenges for the mass production and functional applications of MXene composite aerogels in the field of material engineering.