Data on searching for synergy between alcohol and salt to produce more potent and environmentally benign gas hydrate inhibitors

In order to systematically study the synergistic effect of gas hydrate inhibition with mixtures of methanol (MeOH) and magnesium chloride (MgCl2), the impact of these compounds on the thermodynamic stability of methane hydrate in the systems of CH4-MeOH-H2O, CH4-MgCl2-H2O, and CH4-MeOH-MgCl2-H2O was experimentally investigated. The pressure and temperature conditions of the three-phase vapor-aqueous solution-gas hydrate equilibrium were determined for these systems. The resulting dataset has 164 equilibrium points within the range of 234-289 K and 3-13 MPa. All equilibrium points were measured as the endpoint of methane hydrate dissociation during the heating stage. The phase boundaries of methane hydrate were identified for 8 systems with MeOH (up to 60 mass%), 5 MgCl2 solutions (up to 26.7 mass%), and 14 mixtures of both inhibitors. Most equilibrium points were measured using a ramp heating technique (0.1 K/h) under isochoric conditions when the fluids were stirred at 600 rpm. It was found that even a 0.5 K/h heating rate for the CH4-MgCl2-H2O system at low salt concentrations, along with all mixed aqueous solutions with methanol, gives results that do not differ from 0.1 K/h, considering the measurement uncertainties. Most measurements for the CH4-MgCl2-H2O system at high salt content were acquired using a step heating technique. The coefficients of the empirical equations approximating the equilibrium points for each inhibitor concentration were defined. The change in the slope parameter of the empirical equation was analyzed as a function of inhibitor content. Correlations that accurately describe the thermodynamic inhibition effect of methane hydrate with methanol and magnesium chloride on a mass% and mol% scale were obtained. The freezing temperatures of single and mixed aqueous solutions of methanol and magnesium chloride were determined experimentally to confirm the thermodynamic consistency of the methane hydrate equilibrium data.

Dataset for the phase equilibria and PXRD studies of urea as a green thermodynamic inhibitor of sII gas hydrates

The equilibrium conditions of sII methane/propane hydrates have been experimentally determined for the C₃H₈/CH₄-H₂O-urea system. The equilibrium dissociation temperatures and pressures of sII hydrates span a wide P,T-range (266.7-293.9 K; 0.87-9.49 MPa) and were measured by varying the feed mass fraction of urea in solution from 0 to 50 mass%. The experimental points at feed urea concentration ≤ 40 mass% correspond to the V-L_w-H equilibrium (gas-aqueous urea solution-gas hydrate). A four-phase V-L_w-H-S_u equilibrium (with an additional phase of solid urea) was observed because the solubility limit of urea in water was reached for all points at a feed mass fraction of 50 mass% and for one point at 40 mass% (266.93 K). Gas hydrate equilibria were measured using a high-pressure rig GHA350 under isochoric conditions with rapid fluid stirring and slow ramp heating of 0.1 K/h. Each measured point represents complete dissociation of the sII hydrate. The phase equilibrium data was compared with the literature reported for the C₃H₈/CH₄-H₂O and CH₄-H₂O-urea systems. A comprehensive analysis of the thermodynamic inhibition effect of urea to sII C₃H₈/CH₄ hydrates on pressure and concentration of the inhibitor was carried out. The phase composition of the samples was analyzed by powder X-ray diffractometry at 173 K.

Dataset for the experimental study of dimethyl sulfoxide as a thermodynamic inhibitor of methane hydrate formation

To determine the ability of dimethyl sulfoxide (DMSO) to inhibit methane hydrate formation by the thermodynamic mechanism, we measured the pressures and temperatures of monovariant equilibrium of three phases: gaseous methane, aqueous DMSO solution, and methane hydrate. A total of 54 equilibrium points were obtained. Hydrate equilibrium conditions have been measured for eight different concentrations of dimethyl sulfoxide ranging from 0 to 55 mass%, at temperatures of 242-289 K and pressures of 3-13 MPa. Measurements were performed in an isochoric autoclave (volume of 600 cm³, inside diameter of 8.5 cm) at a heating rate of 0.1 K/h and intense fluid agitation (600 rpm) with four-blade impeller (diameter of 6.1 cm, blade height of 2 cm). The specified stirring speed for aqueous DMSO solutions at 273-293 K is equivalent to a range of Reynolds numbers of 5.3‧10³-3.7‧10⁴. The endpoint of methane hydrate dissociation at defined temperature and pressure values was taken as the equilibrium point. The anti-hydrate activity of DMSO was analyzed on a mass% and mol% scale. Precise correlations between the thermodynamic inhibition effect of dimethyl sulfoxide ΔT_h and the influencing factors (DMSO concentration and pressure) were derived. Powder X-ray diffractometry was employed to examine the phase composition of the samples at 153 K. Measurement of ice freezing points in aqueous solutions of dimethyl sulfoxide (up to 50 mass%) at ambient pressure allowed us to clarify the location of the liquidus line in the DMSO-H₂O system and to check the hydrate equilibrium data for thermodynamic consistency.

Dataset for the new insights into methane hydrate inhibition with blends of vinyl lactam polymer and methanol, monoethylene glycol, or diethylene glycol as hybrid inhibitors

Three-phase equilibrium conditions of vapor-aqueous solution-gas hydrate coexistence for the systems of CH₄-H₂O-organic thermodynamic inhibitor (THI) were experimentally determined. Hydrate equilibrium measurements for systems with methanol (MeOH), monoethylene glycol (MEG), and diethylene glycol (DEG) were conducted. Five concentrations of each inhibitor (maximum content 50 mass%) were studied in the pressure range of 4.9-8.4 MPa. The equilibrium temperature and pressure in the point of complete dissociation of methane hydrate during constant-rate heating combined with vigorous mixing of fluids (600 rpm) in a high-pressure vessel were determined. We compared our experimental points with reliable literature data. The coefficients of empirical equations are derived, which accurately describe hydrate equilibrium conditions for the studied systems. The effect of THI concentration and pressure on methane hydrate equilibrium temperature suppression was analyzed. In the second stage, we studied the kinetics of methane hydrate nucleation/growth in systems containing a polymeric KHI (0.5 mass% of N-vinylpyrrolidone and N-vinylcaprolactam copolymer) in water or THI aqueous solution. For this, temperatures, pressures, and subcoolings of methane hydrate onset were measured by rocking cell tests (RCS6 rig, ramp cooling at 1 K/h). Gas uptake curves characterizing the methane hydrate crystallization kinetics in the polythermal regime were obtained.

Dataset for the dimethyl sulfoxide as a novel thermodynamic inhibitor of carbon dioxide hydrate formation

The temperatures and pressures of the three-phase equilibrium V-L_w-H (gas – aqueous solution – gas hydrate) were measured in the CO₂ – H₂O – dimethyl sulfoxide (DMSO) system at concentrations of organic solute in the aqueous phase up to 50 mass%. Measurements of CO₂ hydrate equilibrium conditions were carried out using a constant volume autoclave by continuous heating at a rate of 0.1 K/h with simultaneous stirring of fluids by a four-blade agitator at 600 rpm. The equilibrium temperature and pressure of CO₂ hydrate were determined for the endpoint of the hydrate dissociation in each experiment. The CO₂ gas fugacity was calculated by the equation of state for carbon dioxide for the measured points. The flow regime in the autoclave during the operation of the stirring system was characterized by calculating the Reynolds number using literature data on the viscosity and density of water and DMSO aqueous solutions. We employed regression analysis to approximate the dependences of equilibrium pressure (CO₂ gas fugacity) on temperature by two- and three-parameter equations. For each measured point, the value of CO₂ hydrate equilibrium temperature suppression ΔT_h was computed. The dependences of this quantity on CO₂ gas fugacity are considered for all DMSO concentrations. The coefficients of empirical correlation describing ΔT_h as a function of the DMSO mass fraction in solution and the equilibrium gas pressure are determined.

This article is a co-submission with a paper [1].

Performance of Waterborne Polyurethanes in Inhibition of Gas Hydrate Formation and Corrosion: Influence of Hydrophobic Fragments

The design of new dual-function inhibitors simultaneously preventing hydrate formation and corrosion is a relevant issue for the oil and gas industry. The structure-property relationship for a promising class of hybrid inhibitors based on waterborne polyurethanes (WPU) was studied in this work. Variation of diethanolamines differing in the size and branching of N-substituents (methyl, n-butyl, and tert-butyl), as well as the amount of these groups, allowed the structure of polymer molecules to be preset during their synthesis. To assess the hydrate and corrosion inhibition efficiency of developed reagents pressurized rocking cells, electrochemistry and weight-loss techniques were used. A distinct effect of these variables altering the hydrophobicity of obtained compounds on their target properties was revealed. Polymers with increased content of diethanolamine fragments with n- or tert-butyl as N-substituent (WPU-6 and WPU-7, respectively) worked as dual-function inhibitors, showing nearly the same efficiency as commercial ones at low concentration (0.25 wt%), with the branched one (tert-butyl; WPU-7) turning out to be more effective as a corrosion inhibitor. Commercial kinetic hydrate inhibitor Luvicap 55 W and corrosion inhibitor Armohib CI-28 were taken as reference samples. Preliminary study reveals that WPU-6 and WPU-7 polyurethanes as well as Luvicap 55 W are all poorly biodegradable compounds; BODt/CODcr (ratio of Biochemical oxygen demand and Chemical oxygen demand) value is 0.234 and 0.294 for WPU-6 and WPU-7, respectively, compared to 0.251 for commercial kinetic hydrate inhibitor Luvicap 55 W. Since the obtained polyurethanes have a bifunctional effect and operate at low enough concentrations, their employment is expected to reduce both operating costs and environmental impact.

Nucleation rates of methane hydrate from water in oil emulsions

Nucleation of methane hydrate from water emulsions in five different kinds of crude oil and in decane have been studied with the use of isothermal methods. The experiments were conducted at a temperature of –5 °C and pressure of 12 MPa. It is shown that the nucleation rates tend to decrease with the increase in the density of the organic liquid used to make the emulsion. It is most likely that the observed regularities are related to the rate of methane diffusion to water surface.