Safety assessment of the substance 'phosphorous acid, triphenyl ester, polymer with 1,4-cyclohexanedimethanol and polypropylene glycol, C10-16 alkyl esters', for use in food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the substance 'phosphorous acid, triphenyl ester, polymer with 1,4-cyclohexanedimethanol and polypropylene glycol, C10-16 alkyl esters', when used as an additive in all types of polyolefins. The substance is a polymer containing ≤ 13% w/w of a low molecular weight fraction (LMWF, < 1000 Da). A polyethylene sample with 0.15% w/w of the substance was used in a comprehensive set of migration tests with food simulants. The specific migration was up to 0.014 and 0.023 mg/kg in 4% acetic acid and 10% ethanol, respectively. Migration into olive oil was estimated by the Panel to be up to 5.3 mg/kg under worst-case conditions of use. The migrating LMWF species were comprehensively identified. Those without phosphorous were either without alerts for genotoxicity or listed in Regulation (EU) 10/2011 with worst-case migrations well below their respective specific migration limits. Toxicological studies were performed using phosphite and phosphate versions of the substance enriched in its LMWF. The substance does not raise a concern for genotoxicity. From a repeated dose 90-day oral toxicity study in rats with a 50:50 phosphite:phosphate blend, the Panel identified a NOAEL of 250 mg/kg bw per day for each component of the blend. No delayed neurotoxicity in hens was observed. The CEP Panel concluded that the substance does not raise a safety concern for the consumer if its LMWF is not higher than 13% w/w, if it is used at up to 0.15% w/w in polyolefin materials and articles intended for contact with all food types, except for infant formula and human milk, for long-term storage at room temperature and below, after hot-fill and/or heating up to 100°C for up to 2 h, and if its migration does not exceed 5 mg/kg food.

Safety assessment of the substance calcium tert-butylphosphonate for use in food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids assessed the safety of calcium tert-butylphosphonate, which is intended to be used as a nucleating agent up to 0.15% w/w for the manufacture of polyolefin food contact materials (FCM) and articles for single and repeated use, in contact with all types of food, including infant formula and human milk. Specific migration was tested using polyethylene samples in 10% ethanol, 3% acetic acid and 95% ethanol for 2 h at 100°C, followed by 238 h at 40°C. Results for all three simulants were near or below the limit of detection of 10 μg/kg. As the solubility of the substance is far above the reported migration and above 60 mg/kg food, no assessment of the particle fraction was needed, and the conventional risk assessment was followed. The substance did not induce gene mutations in bacterial cells and structural chromosomal aberrations in mammalian cells, thus, did not raise concern for genotoxicity. The Panel considered that the use of the substance did not give rise to safety concern related to neurotoxicity for the general population, but this conclusion could not be applied to infants below 16 weeks of age, due to their specific sensitivity and the absence of dedicated data. The Panel concluded that calcium tert-butylphosphonate does not raise a safety concern for the consumer if it is used as a nucleating agent up to 0.15% w/w in the manufacture of polyolefin FCM that are intended to be in contact with all types of food for storage above 6 months at room temperature and below, including temperatures up to 100°C for maximum 2 h and up to 130°C for short durations. The Panel could not evaluate the safety of use to manufacture FCM for contact with infant formula and human milk.

Safety assessment of the process Martogg Group, based on the EREMA Advanced technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids assessed the safety of the recycling process Martogg Group (EU register number RECYC321), which uses the EREMA Advanced technology. The input material is ■■■■■ washed and dried poly(ethylene terephthalate) (PET) flakes originating from collected post-consumer PET containers, including no more than 5% PET from non-food consumer applications. The flakes are heated in continuous reactors ■■■■■ before being extruded. Having examined the challenge test provided, the Panel concluded that the continuous decontamination steps (Steps 2 and 3), for which a challenge test was provided, are critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of this step are temperature, pressure and residence time. It was demonstrated that this recycling process is able to ensure a level of migration of potential unknown contaminants into food below the conservatively modelled migration of 0.1 μg/kg food derived from the exposure scenario for infants when such recycled PET is used at up to 100%. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. Articles made of this recycled PET are not intended to be used in microwave or conventional ovens and such uses are not covered by this evaluation.

Safety assessment of mixtures of 1,9-nonanediamine (NMDA) and 2-methyl-1,8-octanediamine (MODA), for use in food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of mixtures of 1,9-nonanediamine (NMDA) and 2-methyl-1,8-octanediamine (MODA) when used to produce polyamide food contact materials for contact with all food types for long-term storage at room temperature and below, including heating up to 121°C for up to 2 h. The polyamide material is also intended to be used for repeated use up to 121°C with short contact (up to 30 min). The polymer typically contains ■■■■■ of a low molecular weight fraction (LMWF, < 1000 Da). The specific migration was measured with polyamide samples in a set of migration tests with 3% acetic acid and 10% ethanol. NMDA and MODA were not detected at ■■■■■, respectively. The specific migration of the LMWF consisting of NMDA/MODA-related species was up to ■■■■■. The overall migration in olive oil was below the detection limit (3 mg/dm2). The most abundant migrating LMWF oligomers were identified. Toxicological studies were performed with NMDA, MODA and with polyamide formulations enriched in the LMWF. The results of genotoxicity assays did not raise a concern. From a repeated-dose oral 90-day toxicity study in rats, the Panel identified a no observed adverse effect level (NOAEL) of 1000 mg/kg body weight per day for the migrating LMWF. The CEP Panel concluded that NMDA/MODA mixtures do not raise a safety concern for the consumer when used as comonomer with terephthalic acid to manufacture polyamide articles intended for contact with all food types, except for infant formula and human milk, if the migration of NMDA and MODA does not exceed 0.05 mg/kg food (as a sum of the two substances) and if the migration of the LMWF consisting of NMDA/MODA-related species does not exceed 5 mg/kg food.

Safety assessment of the process Lietpak, based on the EREMA MPR technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Lietpak (EU register number RECYC319), which uses the EREMA MPR technology. The input material is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes originating from collected post-consumer PET containers, including no more than 5% PET from non-food consumer applications. The flakes are heated ■■■■■ under vacuum (step 2). Having examined the challenge test provided, the Panel concluded that this step 2, for which the challenge test was provided, is critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of this step are temperature, pressure and residence time. It was demonstrated that this recycling process is able to ensure a level of migration of potential unknown contaminants into food below the conservatively modelled migration of 0.15 μg/kg food, derived from the exposure scenario for toddlers, when such recycled PET is used at up to 100%. Therefore, the Panel concluded that the recycled PET obtained from this process is not considered to be of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, except drinking water, for long-term storage at room temperature or below, with or without hot fill. Articles made of this recycled PET are not intended to be used in microwave or conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process CeltiPak, based on the Kreyenborg IR Clean+ technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process CeltiPak (EU register number RECYC318), which uses the Kreyenborg IR Clean+ technology. The input material is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes originating from collected post-consumer PET containers, for example, bottles, with no more than 5% PET from non-food consumer applications. The flakes are heated in a continuous IR dryer (step 2) before being processed in a finisher reactor (step 3). Having examined the challenge test provided, the Panel concluded that step 2 and step 3 are critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of these critical steps are temperature, air/PET ratio and residence time. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.10 and 0.15 μg/kg food, derived from the exposure scenario for infants and toddlers, respectively, when such recycled PET is used at up to 100%. Therefore, the Panel concluded that the recycled PET obtained from this process is not considered to be of safety concern, when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. Articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process GTX Hanex, based on the Kreyenborg IR Clean+ technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process GTX Hanex (EU register number RECYC317), which uses the Kreyenborg IR Clean+ technology. The input material is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes originating from collected post-consumer PET containers, e.g. bottles, with no more than 5% PET from non-food consumer applications. The flakes are heated in a continuous IR dryer (step 2) before being processed in a finisher reactor (step 3). Having examined the challenge test provided, the Panel concluded that step 2 and step 3 are critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of these critical steps are temperature, air/PET ratio and residence time. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.10 and 0.15 μg/kg food, derived from the exposure scenario for infants and toddlers, respectively, when such recycled PET is used at up to 100%. Therefore, the Panel concluded that the recycled PET obtained from this process is not considered to be of safety concern, when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. Articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Reliance Industries, based on the ProTec technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Reliance Industries (EU register number RECYC315), which uses the ProTec technology. The input material consists of washed and dried poly(ethylene terephthalate) (PET) flakes, mainly originating from collected post-consumer PET containers, e.g. bottles, with no more than 5% PET from non-food consumer applications. The flakes are extruded into pellets (step 1), crystallised (step 2) and treated in a solid-state polycondensation (SSP) reactor (step 3). Having examined the challenge test provided, the Panel concluded that the extrusion and the decontamination in the ■■■■■ SSP reactor (steps 1 and 3) are critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of these critical steps are temperature, pressure and residence time. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not considered to be of safety concern, when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Shinkong, based on the EREMA Basic technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Shinkong (EU register number RECYC320), which uses the EREMA Basic technology. The input material is ■■■■■ washed and dried poly(ethylene terephthalate) (PET) flakes originating from collected post-consumer PET containers, including no more than 5% PET from non-food consumer applications. The flakes are heated in a continuous reactor ■■■■■ before being extruded. Having examined the challenge test provided, the Panel concluded that the continuous decontamination (step 2), for which a challenge test was provided, is critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of this step are temperature, pressure and residence time. It was demonstrated that this recycling process is able to ensure a level of migration of potential unknown contaminants into food below the conservatively modelled migration of 0.1 μg/kg food derived from the exposure scenario for infants, when such recycled PET is used at up to 100%. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. Articles made of this recycled PET are not intended to be used in microwave or conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process ENPLATER, based on the Kreyenborg IR clean+ technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process ENPLATER (EU register number RECYC316), which uses the Kreyenborg IR Clean+ technology. The input material is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes originating from collected post-consumer PET containers, e.g. bottles, with no more than 5% PET from non-food consumer applications. The flakes are heated in a continuous IR dryer (step 2) before being processed in a finisher reactor (step 3). Having examined the challenge test provided, the Panel concluded that step 2 and step 3 are critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of these critical steps are temperature, air/PET ratio and residence time. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.10 and 0.15 μg/kg food, derived from the exposure scenario for infants and toddlers, respectively, when such recycled PET is used at up to 100%. Therefore, the Panel concluded that the recycled PET obtained from this process is not considered to be of safety concern, when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. Articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Reciclar, based on the EREMA Basic technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Reciclar (EU register number RECYC314), which uses the EREMA Basic technology. The input material is ■■■■■ washed and dried poly(ethylene terephthalate) (PET) flakes originating from collected post-consumer PET containers, including no more than 5% PET from non-food consumer applications. The flakes are heated in a continuous reactor under vacuum before being extruded. Having examined the challenge test provided, the Panel concluded that the continuous decontamination (step 2), for which a challenge test was provided, is critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of this step are temperature, pressure and residence time. It was demonstrated that this recycling process is able to ensure a level of migration of potential unknown contaminants into food below the conservatively modelled migration of 0.1 μg/kg food, derived from the exposure scenario for infants, when such recycled PET is used at up to 95% in mixtures with virgin PET, and of 0.15 μg/kg food, derived from the exposure scenario for toddlers, when used at up to 100%. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 95% in mixtures with virgin PET for manufacturing of materials and articles for contact with all types of foodstuffs, including drinking water bottles, and at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, except drinking water, for long-term storage at room temperature or below, with or without hotfill. Articles made of this recycled PET are not intended to be used in microwave or conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Novatex, based on the EREMA Basic technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Novatex (EU register number RECYC313), which uses the EREMA Basic technology. The input material is ■■■■■ washed and dried poly(ethylene terephthalate) (PET) flakes originating from collected post-consumer PET containers, including no more than 5% PET from non-food consumer applications. The flakes are heated in a continuous reactor under vacuum before being extruded. Having examined the challenge test provided, the Panel concluded that the continuous decontamination (step 2), for which a challenge test was provided, is critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of this step are temperature, pressure and residence time. It was demonstrated that this recycling process is able to ensure a level of migration of potential unknown contaminants into food below the conservatively modelled migration of 0.1 μg/kg food derived from the exposure scenario for infants when such recycled PET is used at up to 95% in mixtures with virgin PET, and of 0.15 μg/kg food, derived from the exposure scenario for toddlers when used at up to 100%. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 95% in mixtures with virgin PET for manufacturing of materials and articles for contact with all types of foodstuffs, including drinking water bottles, and at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs except drinking water, for long-term storage at room temperature or below, with or without hotfill. Articles made of this recycled PET are not intended to be used in microwave or conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Intco Malaysia, based on the VACUNITE (EREMA basic and Polymetrix SSP V-leaN) technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Intco Malaysia (EU register number RECYC309), which uses the VACUNITE (EREMA basic and Polymetrix SSP V-leaN) technology. The input consists of hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are pre-decontaminated in the ■■■■■ at ■■■■■ under ■■■■■ (step 2), then extruded and pelletised. The ■■■■■ pellets are then ■■■■■ and submitted to solid-state polycondensation (SSP) at ■■■■■ under ■■■■■ and ■■■■■. Having examined the challenge tests provided, the Panel concluded that the step 2 (flake reactor) and steps 4 and 5 (preheating and SSP) are critical for determining the decontamination efficiency of the process. The operating parameters to control the performance are temperature, pressure and residence time for steps 2, 4 and 5 as well as the ■■■■■ for steps 4 and 5. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern, when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process INCOM RESOURCES RECOVERY (TIANJIN), based on the Buhler technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process INCOM RESOURCES RECOVERY (TIANJIN) (EU register number RECYC312), which uses the Buhler technology. The input material consists of hot washed and dried poly(ethylene terephthalate) (PET) flakes originating from collected post-consumer PET containers, e.g. bottles, including no more than 5% PET from non-food consumer applications. Washed and dried flakes are extruded into pellets, which are dried and crystallised in a reactor and then preheated and further treated in a solid-state polymerisation (SSP) reactor. The recycled pellets are intended to be used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. The Panel concluded that the information submitted to EFSA is inadequate to demonstrate that this recycling process is able to reduce potential unknown contamination of the input PET flakes to a concentration that does not pose a risk to human health.

Safety assessment of the process Guangxi Wuzhou Guolong Recyclable, based on the Vacunite (EREMA basic and Polymetrix SSP V-LeaN) technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Guangxi Wuzhou Guolong Recyclable (EU register number RECYC310), which uses the VACUNITE (EREMA basic and Polymetrix SSP V-leaN) technology. The input consists of hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes, mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are pre-decontaminated in the ■■■■■ at ■■■■■ under ■■■■■ (step 2) before being extruded, pelletised and crystallised (step 3). The ■■■■■ pellets are then ■■■■■ (step 4) and submitted to solid-state polycondensation (SSP) (step 5) at high temperature under ■■■■■ and ■■■■■. Having examined the challenge tests provided, the Panel concluded that step 2 as well as steps 4 and 5 are critical for determining the decontamination efficiency of the process. The operating parameters to control the performance are temperature, pressure and residence time for steps 2, 4 and 5 as well as the ■■■■■ for steps 4 and 5. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern, when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. Articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Rekis, based on the VACUNITE (EREMA basic and Polymetrix SSP V-leaN) technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Rekis (EU register number RECYC311), which uses the VACUNITE (EREMA basic and Polymetrix SSP V-leaN) technology. The input is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are pre-decontaminated in the ■■■■■ at ■■■■■ under ■■■■■ (step 2) before being extruded, pelletised and ■■■■■ (step 3). The crystallised pellets are then ■■■■■ (step 4) and submitted to solid-state polycondensation (SSP) (step 5) at ■■■■■, under ■■■■■ and ■■■■■. Having examined the challenge tests provided, the Panel concluded that step 2 as well as steps 4 and 5 are critical for determining the decontamination efficiency of the process. The operating parameters to control the performance are temperature, pressure and residence time for steps 2, 4 and 5 as well as the gas velocity for steps 4 and 5. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern, when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Concept Plastics Packaging, based on the Gneuss 2 technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Concept Plastics Packaging (EU register number RECYC300), which uses the Gneuss 2 technology. The input consists of washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are extruded ■■■■■ into sheets. Having examined the challenge test provided, the Panel concluded that the decontamination in the extruder ■■■■■ is critical in determining the decontamination efficiency of the process. The operating parameters to control the performance are the pressure, the temperature, the throughput, the rotor speed and the satellite screws speed. It was demonstrated that this recycling process is able to ensure a level of migration of potential unknown contaminants into food below the conservatively modelled migration of 0.10 μg/kg food, derived from the exposure scenario for infants, when such recycled PET is used at up to 90% in mixtures with virgin PET, and of 0.15 μg/kg food, derived from the exposure scenario for toddlers, when such recycled PET is used at up to 100%. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used for the manufacture of materials and articles at up to (a) 100% for contact with all types of foodstuffs except drinking water and (b) 90% in mixtures with virgin PET for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Battenfeld-Cincinnati Germany, based on the Battenfeld technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Battenfeld-Cincinnati Germany (EU register number RECYC303), which uses the Battenfeld technology. The input consists of washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are heated and pre-decontaminated in an ■■■■■, then further decontaminated by extrusion to sheets ■■■■■. Having examined the challenge test provided, the Panel concluded that the ■■■■■ drying (step 2) and extrusion (step 3) are critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of these critical steps are temperature and residence time for step 2, temperature, throughput and pressure for step 3. The Panel concluded that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.15 μg/kg food, exposure scenario for toddlers, under the following conditions of use of the recycled PET: (a) 45% in mixtures with virgin PET to produce trays for storage of fruits and vegetables up to 30 days at room temperature or below, (b) 100% to produce cups for storage of soft drinks and beers up to 1 day at room temperature or below, (c) 100% to produce trays for meat storage up to 30 days at 6°C. Hotfill is not included. Therefore, the Panel concluded that the recycled PET produced by this process is not of safety concern when used under the evaluated conditions. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Shangrao Bisource Technology, based on the Vacurema Prime technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Shangrao Bisource Technology (EU register number RECYC306), which uses the Vacurema Prime technology. The input is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are heated in a batch reactor (Step 2) under vacuum and then treated at higher temperature in a continuous reactor (Step 3) under vacuum before being extruded into pellets. Having examined the challenge test provided, the Panel concluded that Steps 2 and 3 are critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of these steps are temperature, pressure and residence time. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, soft drinks, juices, tea, milk, oil, alcoholic beverages and other food products, for long-term storage at room temperature or below, with or without hot fill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Arcoplastica, based on the Bandera PURe 15 technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Arcoplastica (EU register number RECYC308), which uses the Bandera PURe15 technology. The input consists of hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are ■■■■■. Having examined the challenge test provided, the Panel concluded that the ■■■■■ are critical for the decontamination efficiency. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens, and such uses are not covered by this evaluation.

Safety assessment of the process Ambiental de Plasticos Recyclapet, based on the Vacurema Prime technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Ambiental de Plasticos Recyclapet (EU register number RECYC304), which uses the Vacurema Prime technology. The input is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are heated in a batch reactor (Step 2) under vacuum and then treated at higher temperature in a continuous reactor (Step 3) under vacuum before being extruded into pellets. Having examined the challenge test provided, the Panel concluded that Steps 2 and 3 are critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of these steps are temperature, pressure and residence time. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, soft drinks, juices, tea, milk, oil, alcoholic beverages and other food products, for long-term storage at room temperature or below, with or without hot fill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process ENVICCO, based on EREMA basic and Polymetrix SSP leaN technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process ENVICCO (EU register number RECYC301), which uses the EREMA basic and Polymetrix SSP leaN technology. The input consists of hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are pre-decontaminated in the EREMA reactor at high temperature under vacuum (step 2) before being extruded, pelletised and crystallised (step 3). The crystallised pellets are then preheated (step 4) and submitted to solid-state polycondensation (SSP) (step 5) at ■■■■■ temperature and under nitrogen flow. Having examined the challenge tests provided, the Panel concluded that step 2 as well as steps 4 and 5 are critical for determining the decontamination efficiency of the process. The operating parameters to control the performance of these critical steps are temperature, pressure and residence time for step 2 and temperature, residence time and gas velocity for steps 4 and 5. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern, when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Acepolymer, based on the Vacurema Prime technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Acepolymer (EU register number RECYC305), which uses the Vacurema Prime technology. The input is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are heated in a batch reactor (Step 2) under vacuum and then treated at higher temperature in a continuous reactor (Step 3) under vacuum before being extruded into pellets. Having examined the challenge test provided, the Panel concluded that Steps 2 and 3 are critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of these steps are temperature, pressure and residence time. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, soft drinks, juices, tea, milk, oil, alcoholic beverages and other food products, for long-term storage at room temperature or below, with or without hot fill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Umincorp, based on the NGR technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Umincorp (EU register number RECYC302), which uses the NGR technology. The input consists of washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are dried (step 2), melted in an extruder (step 3) and decontaminated during a melt-state polycondensation step ■■■■■ (step 4). In step 5, the melt is cooled down and granulated. Having examined the challenge test provided, the Panel concluded that the melt-state polycondensation (step 4) is critical in determining the decontamination efficiency of the process. The operating parameters to control the performance are the pressure, the temperature, the residence time (depending on the mass and throughput of the melt) and the characteristics of the reactor. It was demonstrated by the challenge test that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Poly Recycling, based on the Vacurema Prime technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Poly Recycling (EU register number RECYC307), which uses the Vacurema Prime technology. The input is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are heated in a batch reactor (Step 2) under vacuum and then treated at higher temperature in a continuous reactor (Step 3) under vacuum before being extruded into pellets. Having examined the challenge test provided, the Panel concluded that Steps 2 and 3 are critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of these steps are temperature, pressure and residence time. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, soft drinks, juices, tea, milk, oil, alcoholic beverages and other food products, for long-term storage at room temperature or below, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process PCR Ambalaj, based on the Starlinger iV+ technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process PCR Ambalaj (EU register number RECYC294), which uses the Starlinger iV+ technology. The input is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are dried and crystallised in a first reactor, then extruded into pellets. These pellets are crystallised, preheated and treated in a solid-state polycondensation (SSP) reactor. Having examined the challenge test provided, the Panel concluded that the drying and crystallisation (step 2), extrusion and crystallisation (step 3) and SSP (step 4) are critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of these critical steps are temperature, air/PET ratio and residence time for the drying and crystallisation step, and temperature, pressure and residence time for the extrusion and crystallisation step as well as the SSP step. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process RE-PETKunststoffrecycling, based on Gneuss 4 technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process RE-PETKunststoffrecycling (EU register number RECYC286), which uses the Gneuss 4 technology. The input consists of washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are melted in an extruder (step 2) and decontaminated during a melt-state polycondensation step under ■■■■■ and vacuum (step 3) and finally pelletised. Having examined the challenge test provided, the Panel concluded that the melt-state polycondensation (step 3) is critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of the critical step are the pressure, the temperature, the residence time and the characteristics of the reactor. It was demonstrated by the challenge test that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Plastrec, based on the Polymetrix technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Plastrec (EU register number RECYC288), which uses the Polymetrix technology. The input material consists of hot washed and dried poly(ethylene terephthalate) (PET) flakes originating from collected post-consumer PET containers, e.g. bottles, including no more than 5% PET from non-food consumer applications. The flakes are extruded to pellets, crystallised and subsequently decontaminated in a solid-state polycondensation (SSP) reactor under high temperature and gas flow. Having examined the challenge tests provided, the Panel concluded that the fourth step, the decontamination in the SSP reactor, is critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of this critical step are temperature, gas velocity and residence time. It was demonstrated that this recycling process is able to ensure a level of migration of potential unknown contaminants into food below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not considered to be of safety concern, when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave or conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Silver Plastics, based on the Reifenhäuser technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Silver Plastics (EU register number RECYC299), which uses the Reifenhäuser technology. The input material consists of hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, including no more than 5% PET from non-food consumer applications. The flakes are extruded under vacuum into sheets. Having examined the challenge test provided, the Panel concluded that the decontamination in the extruder under vacuum degassing (step 2), for which a challenge test was provided, is critical in determining the decontamination efficiency of the process. The operating parameters to control the performance are temperature, pressure and throughput. The Panel concluded that this recycling process is able to ensure a level of exposure to potential unknown contaminants from food below 0.0025 μg/kg bw per day, when such recycled PET is used from 15% to 100% in mixtures with virgin PET, depending on the specific intended application. Therefore, the Panel concluded that the recycled PET obtained from this process is not considered to be of safety concern when used from 15% to 100% in mixtures with virgin PET for the manufacture of materials and articles depending on the specific intended application. Articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Tanrikulu Plastik, based on the Starlinger iV+ technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Tanrikulu Plastik (EU register number RECYC295), which uses the Starlinger iV+ technology. The input is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are dried and crystallised in a first reactor, then extruded into pellets. These pellets are crystallised, preheated and treated in a solid-state polycondensation (SSP) reactor. Having examined the challenge test provided, the Panel concluded that the drying and crystallisation (step 2), extrusion and crystallisation (step 3) and SSP (step 4) are critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of these critical steps are temperature, air/PET ratio and residence time for the drying and crystallisation step, and temperature, pressure and residence time for the extrusion and crystallisation step as well as the SSP step. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Veolia Huafei Polymer Technology (Zhejiang), based on the Vacunite (EREMA Basic and Polymetrix SSP V-LeaN) technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Veolia Huafei Polymer Technology (Zhejiang) (EU register numberRECYC292), which uses the VACUNITE (EREMA basic and Polymetrix SSP V-leaN) technology. The input consists of hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes, mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are pre-decontaminated in the ■■■■■ at ■■■■■ under ■■■■■ (step 2) before being extruded, pelletised and ■■■■■ (step 3). The ■■■■■ pellets are then ■■■■■ (step 4) and submitted to solid-state polycondensation (SSP) (step 5) at ■■■■■ and under ■■■■■ and ■■■■■. Having examined the challenge tests provided, the Panel concluded that step 2 as well as steps 4 and 5 are critical for determining the decontamination efficiency of the process. The operating parameters to control the performance are temperature, pressure and residence time for steps 2, 4 and 5 as well as the ■■■■■ for steps 4 and 5. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern, when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. Articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Langgeng, based on the Starlinger deCON technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Langgeng (EU register number RECYC293), which uses the Starlinger deCON technology. The input material is hot washed and dried poly(ethylene terephthalate) (PET) flakes originating from collected post-consumer PET containers, e.g. bottles, with no more than 5% PET from non-food consumer applications. The flakes are preheated before being submitted to solid-state polycondensation (SSP) in a continuous reactor at high temperature under vacuum and gas flow. Having examined the challenge test provided, the Panel concluded that the preheating (step 2) and the decontamination in the SSP reactor (step 3) are critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of these critical steps are temperature, pressure and residence time for steps 2 and 3, reduced gas flow rate for step 2 and gas volume/PET mass ratio for step 3. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not considered to be of safety concern, when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Lerg-Pet, based on the Starlinger iV+ technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Lerg-Pet (EU register number RECYC297), which uses the Starlinger iV+ technology. The input is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are dried and crystallised in a first reactor, then extruded into pellets. These pellets are crystallised, preheated and treated in a solid-state polycondensation (SSP) reactor. Having examined the challenge test provided, the Panel concluded that the drying and crystallisation (step 2), extrusion and crystallisation (step 3) and SSP (step 4) are critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of these critical steps are temperature, air/PET ratio and residence time for the drying and crystallisation step, and temperature, pressure and residence time for the extrusion and crystallisation step as well as the SSP step. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process CPE based on the VACUNITE (EREMA basic and Polymetrix SSP V-leaN) technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process CPE (EU register number RECYC291), which uses the VACUNITE (EREMA basic and Polymetrix SSP V-leaN) technology. The input is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are pre-decontaminated in the flakes reactor at high temperature under ■■■■■ (step 2) before being extruded, pelletised and crystallised (step 3). The crystallised pellets are then preheated (Step 4) and submitted to solid-state polycondensation (SSP) (step 5) at ■■■■■ and ■■■■■ and ■■■■■ flow. Having examined the challenge tests provided, the Panel concluded that step 2 as well as steps 4 and 5 are critical for determining the decontamination efficiency of the process. The operating parameters to control the performance are temperature, pressure and residence time for steps 2, 4 and 5 as well as the ■■■■■ for steps 4 and 5. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern, when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Loreco Plast Recyclage, based on the VACUNITE (EREMA basic and Polymetrix SSP V-leaN) technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Loreco Plast Recyclage (EU register number RECYC290), which uses the VACUNITE (EREMA basic and Polymetrix SSP V-leaN) technology. The input consists of hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are pre-decontaminated in the ■■■■■ at ■■■■■ under ■■■■■ (step 2) before being extruded, pelletised and ■■■■■ (step 3). The ■■■■■ pellets are then ■■■■■ (step 4) and submitted to solid-state polycondensation (SSP) (step 5) at ■■■■■ and under ■■■■■ and ■■■■■ in two parallel ■■■■■ lines. Having examined the challenge tests provided, the Panel concluded that step 2 as well as steps 4 and 5 are critical for determining the decontamination efficiency of the process. The operating parameters to control the performance are temperature, pressure and residence time for steps 2, 4 and 5 as well as the ■■■■■ for steps 4 and 5. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern, when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process ISKO, based on Gneuss 4 technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process ISKO (EU register number RECYC287), which uses the Gneuss 4 technology. The input consists of washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are melted in an extruder (step 2), decontaminated during a melt-state polycondensation step ■■■■■ and vacuum (step 3) and finally pelletised. Having examined the challenge test provided, the Panel concluded that the melt-state polycondensation (step 3) is critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of the critical step are the pressure, the temperature, the residence time and the characteristics of the reactor. It was demonstrated by the challenge test that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Dialog Diyou PCR, based on the Starlinger iV+ technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Dialog Diyou PCR (EU register number RECYC296), which uses the Starlinger iV+ technology. The input is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are dried and crystallised in a first reactor, then extruded into pellets. These pellets are crystallised, preheated and treated in a solid-state polycondensation (SSP) reactor. Having examined the challenge test provided, the Panel concluded that the drying and crystallisation (step 2), extrusion and crystallisation (step 3) and SSP (step 4) are critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of these critical steps are temperature, air/PET ratio and residence time for the drying and crystallisation step, and temperature, pressure and residence time for the extrusion and crystallisation step as well as the SSP step. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Coca-Cola HBC, based on the NGR technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Coca-Cola HBC (EU register number RECYC285), which uses the NGR technology. The input is washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are dried (step 2), melted in an extruder (step 3) and decontaminated during a melt-state polycondensation step ■■■■■ (step 4). In step 5, the material is granulated. Having examined the challenge test provided, the Panel concluded that the melt-state polycondensation (step 4) is critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of the critical step are the pressure, the temperature, the residence time (depending on the mass and throughput of the melt) and the characteristics of the reactor. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the substance poly(2-hydroxypropanoic acid), n-octyl/n-decyl esters, for use in food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of poly(2-hydroxypropanoic acid), n-octyl/n-decyl esters (OLA8), which is intended to be used as a plasticiser into polylactic acid (PLA) in contact with non-fatty foods. OLA8 is intended to be used at up to 5% and 15% w/w with or without starch, respectively (or with other additives with similar function). The migration for 10 days at 40°C from the film without starch was 0.16 mg/kg in 10% ethanol and 0.01 mg/kg in 3% acetic acid, while from the film with the starch it was well above 0.05 mg/kg food in all simulants. Some of the testing conditions were inconsistently reported. The substance did not induce gene mutations in bacterial cells and did not induce structural chromosomal aberrations or polyploidy in mammalian cells, thus, does not raise concern for genotoxicity. Instead of providing a 90-day oral toxicity study, a hydrolysis study in ■■■■■ was submitted to read-across from the authorised starting substances, ■■■■■ and the ■■■■■. However, the data provided did not allow to perform the read-across, thus no appropriate toxicological data were provided to support migration above 0.05 mg/kg food (including for contact with 10% ethanol and use in combination with starch). The Panel concluded that OLA8 does not raise a safety concern for the consumer if it is used as an additive at up to 15% w/w in the manufacture of PLA articles that do not contain starch (and other additives with similar function), that are intended to be in contact for 10 days at 40°C with foods simulated by 3% acetic acid and from which the migration does not exceed 0.05 mg/kg food.

Safety assessment of the process CERSA, based on the Starlinger deCON technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process CERSA (EU register number RECYC298), which uses the Starlinger deCON technology. The input material is hot washed and dried poly(ethylene terephthalate) (PET) flakes originating from collected post-consumer PET containers, e.g. bottles, with no more than 5% PET from non-food consumer applications. The flakes are preheated before being submitted to solid-state polycondensation (SSP) in a continuous reactor at high temperature under vacuum and gas flow. Having examined the challenge test provided, the Panel concluded that the preheating (step 2) and the decontamination in the SSP reactor (step 3) are critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of these critical steps are temperature, pressure and residence time for steps 2 and 3, reduced gas flow rate for step 2 and gas volume/PET mass ratio for step 3. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not considered to be of safety concern, when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process CCH CIRCULARPET, based on the NGR technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process CCH CIRCULARPET (EU register number RECYC284), which uses the NGR technology. The input is washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are dried (step 2), melted in an extruder (step 3) and decontaminated during a melt-state polycondensation step ■■■■■ (step 4). In step 5, the material is granulated. Having examined the challenge test provided, the Panel concluded that the melt-state polycondensation (step 4) is critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of the critical step are the pressure, the temperature, the residence time (depending on the mass and throughput of the melt) and the characteristics of the reactor. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Cirrec Netherlands BV, based on the EREMA Basic technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Cirrec Netherlands BV (EU register number RECYC283), which uses the EREMA Basic technology. The input material is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes originating from collected post-consumer PET containers, including less than 5% PET from non-food consumer applications. The flakes are heated in a continuous reactor under vacuum before being extruded. Having examined the challenge test provided, the Panel concluded that the continuous decontamination (step 2), for which a challenge test was provided, is critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of this step are temperature, pressure and residence time. It was demonstrated that this recycling process is able to ensure a level of migration of potential unknown contaminants into food below the conservatively modelled migration of 0.1 μg/kg food, derived from the exposure scenario for infants when such recycled PET is used at up to 100%. Therefore, the Panel concluded that the recycled PET obtained from this process is not considered to be of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature or below, with or without hotfill. This evaluation does not cover uses of the recycled PET in microwaves or conventional ovens.

Safety assessment of the process PT Veolia Indonesia, based on the Polymetrix technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process PT Veolia Indonesia (EU register number RECYC289), which uses the Polymetrix technology. The input material is hot washed and dried poly(ethylene terephthalate) (PET) flakes originating from collected post-consumer PET containers, e.g. bottles, including no more than 5% PET from non-food consumer applications. The flakes are extruded to pellets, crystallised and subsequently decontaminated in a solid-state polycondensation (SSP) reactor under high temperature and gas flow. Having examined the challenge tests provided, the Panel concluded that the fourth step, the decontamination in the SSP reactor, is critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of this critical step are temperature, gas velocity and residence time. It was demonstrated that this recycling process is able to ensure a level of migration of potential unknown contaminants into food below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not considered to be of safety concern, when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave or conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Aristea, based on the Bandera PURe 15 technology, used to recycle post‐consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Aristea (EU register number RECYC282), which uses the Bandera PURe15 technology. The input is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from post‐consumer PET containers, with no more than 5% PET from non‐food consumer applications. The flakes are ■■■■■ Having examined the challenge test provided, the Panel concluded that the ■■■■■ are critical for the decontamination efficiency. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long‐term storage at room temperature, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens, and such uses are not covered by this evaluation.

Safety assessment of the process Renovapet, based on the VACUNITE (EREMA basic and Polymetrix SSP V‐leaN) technology, used to recycle post‐consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Renovapet (EU register number RECYC271), which uses the VACUNITE (EREMA basic and Polymetrix SSP V‐leaN) technology. The input consists of hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post‐consumer PET containers, including no more than 5% PET from non‐food consumer applications. The flakes are pre‐decontaminated in a first ■■■■■ reactor at high temperature under vacuum (step 2), then extruded and pelletised. The pellets are crystallised, ■■■■■ and then submitted to solid‐state polycondensation (SSP) in a continuous reactor at ■■■■■ under ■■■■■ and ■■■■■ (step 4). Having examined the challenge test provided, the Panel concluded that step 2 (■■■■■ reactor) and step 4 (■■■■■ and SSP) are critical for determining the decontamination efficiency of the process. The operating parameters to control the performance are temperature, pressure and residence time for steps 2 and 4 as well as gas velocity for step 4. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern, when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long‐term storage at room temperature, with or without hotfill. Articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Loreco Plast Recyclage, based on the Vacurema Prime technology, used to recycle post‐consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Loreco Plast Recyclage (EU register number RECYC278), which uses the Vacurema Prime technology. The input is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post‐consumer PET containers, with no more than 5% PET from non‐food consumer applications. The flakes are heated in a batch reactor (step 2) under vacuum and then heated at a higher temperature in a continuous reactor (step 3) under vacuum before being extruded into pellets. Having examined the challenge test provided, the Panel concluded that steps 2 and 3 are critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of these steps are temperature, pressure and residence time. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, soft drinks, juices, tea, milk, oil, alcoholic beverages and containers for food products (e.g. sauces), for long‐term storage at room temperature, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Steinbeis PolyVert, based on the Vacunite (EREMA Basic and Polymetrix SSP V-LeaN) technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Steinbeis PolyVert (EU register number RECYC280), which uses the VACUNITE (EREMA Basic and Polymetrix SSP V-leaN) technology. The input consists of hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes, mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are pre-decontaminated in a first ■■■■■ ■■■■■ at high ■■■■■ under vacuum before being extruded, pelletised and crystallised. The pellets are then ■■■■■ and submitted to solid-state polycondensation (SSP) in two parallel ■■■■■ reactor lines at high ■■■■■ under ■■■■■ and ■■■■■. Having examined the challenge test provided, the Panel concluded that step 2 (■■■■■ reactor) and steps 4 and 5 (■■■■■ and SSP) are critical for determining the decontamination efficiency of the process. The operating parameters to control the performance are temperature, pressure and residence time for steps 2, 4 and 5 as well as the gas velocity for steps 4 and 5. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern, when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature, with or without hotfill. Articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Roboplast, based on the Bandera PURe 15 technology, used to recycle post-consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Roboplast (EU register number RECYC281), which uses the Bandera PURe15 technology. The input is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are ■■■■■ Having examined the challenge test provided, the Panel concluded that the ■■■■■ are critical for the decontamination efficiency. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long-term storage at room temperature, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens, and such uses are not covered by this evaluation.

Safety assessment of the process Green PET Recycling, based on the Starlinger iV+ technology, used to recycle post‐consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Green PET Recycling (EU register number RECYC277), which uses the Starlinger iV+ technology. The input is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post‐consumer PET containers, with no more than 5% PET from non‐food consumer applications. The flakes are dried and crystallised in a first reactor, then extruded into pellets. These pellets are crystallised, preheated and treated in a solid‐state polycondensation (SSP) reactor. Having examined the challenge test provided, the Panel concluded that the drying and crystallisation (step 2), extrusion and crystallisation (step 3) and SSP (step 4) are critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of these critical steps are temperature, air/PET ratio and residence time for the drying and crystallisation step, and temperature, pressure and residence time for the extrusion and crystallisation step as well as the SSP step. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long‐term storage at room temperature, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process Royce Universal, based on the Starlinger iV+ technology, used to recycle post‐consumer PET into food contact materials

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Royce Universal (EU register number RECYC276), which uses the Starlinger iV+ technology. The input is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post‐consumer PET containers, with no more than 5% PET from non‐food consumer applications. The flakes are dried and crystallised in a first reactor, then extruded into pellets. These pellets are crystallised, preheated and treated in a solid‐state polycondensation (SSP) reactor. Having examined the challenge test provided, the Panel concluded that the drying and crystallisation (step 2), extrusion and crystallisation (step 3) and SSP (step 4) are critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of these critical steps are temperature, air/PET ratio and residence time for the drying and crystallisation step, and temperature, pressure and residence time for the extrusion and crystallisation step as well as the SSP step. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 μg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs, including drinking water, for long‐term storage at room temperature, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.