The effects of glycols on molecular mobility, structure, and permeability in stratum corneum

The skin provides an attractive alternative to the conventional drug administration routes. Still, it comes with challenges as the upper layer of the skin, the stratum corneum (SC), provides an efficient barrier against permeation of most compounds. One way to overcome the skin barrier is to apply chemical permeation enhancers, which can modify the SC structure. In this paper, we investigated the molecular effect of three different types of glycols in SC: dipropylene glycol (diPG), propylene glycol (PG), and butylene glycol (BG). The aim is to understand how these molecules influence the molecular mobility and structure of the SC components, and to relate the molecular effects to the efficiency of these molecules as permeation enhancers. We used complementary experimental techniques, including natural abundance ¹³C NMR spectroscopy and wide-angle X-ray diffraction to characterize the molecular consequences of these compounds at different doses in SC at 97% RH humidity and 32 °C. In addition, we study the permeation enhancing effects of the same glycols in comparable conditions using Raman spectroscopy. Based on the results from NMR, we conclude that all three glycols cause increased mobility in SC lipids, and that the addition of glycols has an effect on the keratin filaments in similar manner as Natural Moisturizing Factor (NMF). The highest mobility of both lipids and amino acids can be reached with BG, which is followed by PG. It is also shown that one reaches an apparent saturation level for all three chemicals in SC, after which increased addition of the compound does not lead to further increase in the mobility of SC lipids or protein components. The examination with Raman mapping show that BG and PG give a significant permeation enhancement as compared to SC without any added glycol at corresponding conditions. Finally, we observe a non-monotonic response in permeation enhancement with respect to the concentration of glycols, where the highest concentration does not give the highest permeation. This is explained by the dehydration effects at highest glycol concentrations. In summary, we find a good correlation between the molecular effects of glycols on the SC lipid and protein mobility, and macroscopic permeation enhances of the same molecules.

QbD-Based Investigation of Dermal Semisolid in situ Film-Forming Systems for Local Anaesthesia

PURPOSE

The aim of our research work was to develop dermally applicable, lidocaine hydrochloride (LID-HCl)-containing semisolid in situ film-forming systems (FFSs) using the Quality by Design (QbD) approach to increase drug permeation into the skin.

METHODS

Silicones were used to improve the properties of formulations and to increase the permeation through the skin. The QbD approach was applied to ensure quality-based development. With initial risk assessment, the critical material attributes (CMAs) and the critical process parameters (CPPs) were identified to ensure the required critical quality attributes (CQAs).

RESULTS

During the initial risk assessment, four high-risk CQAs, namely in vitro drug release, in vitro drug permeation, drying properties, and mechanical properties, and three medium-risk CQAs, namely pH, viscosity, and film appearance were identified and investigated. Moreover, four high-risk CMAs were also considered during the formulation: permeation enhancing excipients, drying excipients, film-forming excipients, and emollients. During the experiments, LID-HCl influenced these critical parameters highly, thereby reducing the drying time. The formulation containing 25% silicone showed the best mechanical properties (49 mN skin adhesion, 20.3% film flexibility, 1.27 N film burst strength), which could predict better patient adherence. In addition, in vitro permeation studies showed that formulation containing 50% silicone has the fastest permeation rate. The flux of diffused API was 6.763 µg/cm2/h, which is much higher compared to the silicone-free formulation (1.5734 µg/cm2/h), and it can already be observed in the lower part of the dermis in 0.5 hour.

CONCLUSION

Our results show that LID-HCl has great influence on the critical parameters of FFSs. The silicone content can improve the applicability of formulations and has a favorable effect on the permeation rate of LID-HCl into the skin.

Investigation of Silicone-Containing Semisolid in Situ Film-Forming Systems Using QbD Tools

The aim of our research work was to develop dermally applicable, semisolid film-forming systems (FFSs) containing silicones, which form a film on the skin in situ, with suitable mechanical properties for skin application. FFSs were developed and investigated by means of the Quality by Design (QbD) methodology. With this QbD approach, the initial risk assessment defines the critical quality attributes (CQAs), the critical material attributes (CMAs) and the critical process parameters (CPPs) to ensure the required quality. Different semisolid systems were formed with or without silicones. During the initial risk assessment, three CQAs, namely skin adhesion, film flexibility and burst strength, were found to be critical attributes, while film appearance, film integrity and the drying time of the semisolid system, were found to be medium attributes. These parameters were investigated. The initial risk assessment also showed that there are three high CMAs: the type of silicones, film-forming excipients, drying excipients, and that there was one medium CMA: viscosity-enhancing excipients. Based on our results, the silicone content had a great effect on the film-forming systems. Different silicones affected the mechanical properties of the films in varying ways, decreased the drying time and showed promising results regarding the drying mechanism.