Microstructure, mechanical properties, corrosion resistance and cytocompatibility of WE43 Mg alloy scaffolds fabricated by laser powder bed fusion for biomedical applications

Open-porous scaffolds of WE43 Mg alloy with a body-center cubic cell pattern were manufactured by laser powder bed fusion with different strut diameters. The geometry of the unit cells was adequately reproduced during additive manufacturing and the porosity within the struts was minimized. The microstructure of the scaffolds was modified by means of thermal solution and ageing heat treatments and was analysed in detail by means of X-ray microtomography, optical, scanning and transmission electron microscopy. Moreover, the corrosion rates and the mechanical properties of the scaffolds were measured as a function of the strut diameter and metallurgical condition. The microstructure of the as-printed scaffolds contained a mixture of Y-rich oxide particles and Rare Earth-rich intermetallic precipitates. The latter could be modified by heat treatments. The lowest corrosion rates of 2-3 mm/year were found in the as-printed and solution treated scaffolds and they could be reduced to ~0.1 mm/year by surface treatments using plasma electrolytic oxidation. The mechanical properties of the scaffolds improved with the strut diameter: the yield strength increased from 8 to 40 MPa and the elastic modulus improved from 0.2 to 0.8 GPa when the strut diameter increased from 275 μm to 800 μm. Nevertheless, the strength of the scaffolds without plasma electrolytic oxidation treatment decreased rapidly when immersed in simulated body fluid. In vitro bicompatibility tests showed surface treatments by plasma electrolytic oxidation were necessary to ensure cell proliferation in scaffolds with high surface-to-volume ratio.

Influence of design and postprocessing parameters on the degradation behavior and mechanical properties of additively manufactured magnesium scaffolds

Magnesium shows promising properties concerning its use in absorbable implant applications such as biodegradability, improved mechanical strength and plastic deformability. Following extensive research, the first fixation and compression screws composed of magnesium rare earth alloys were commercialised, notably in the field of orthopaedic surgery. Preclinical and clinical follow-up studies showed that the rapid degradation of unprotected metallic Magnesium surfaces and concomitant hydrogen gas bursts still raise concern regarding certain surgical indications and need to be further improved. In order to enlarge the scope of further applications, the development of future magnesium implants must aim at freedom of design and reduction of volume, hereby enabling higher functionalised implants, as e.g. plate systems or scaffold grafts for bone replacement therapy. In order to overcome the boundaries of conventional manufacturing methods such as turning or milling, the process of Laser Powder Bed Fusion (LPBF) for magnesium alloys was recently introduced. It enables the production of lattice structures, therefore allowing for reduction of implant material volume. Nevertheless, the concomitant increase of free surface of such magnesium scaffolds further stresses the aforementioned disadvantages of vast degradation and early loss of mechanical stability if not prevented by suitable postprocessing methods. Magnesium scaffold structures with different pore sizes were therefore manufactured by LPBF and consequently further modified either by thermal heat treatment or Plasma Electrolytic Oxidation (PEO). Implant performance was assessed by conducting degradation studies and mechanical testing. PEO modified scaffolds with small pore sizes exhibited improved long-term stability, while heat treated specimens showed impaired performance regarding degradation and mechanical stability. STATEMENT OF SIGNIFICANCE: Magnesium based scaffold structures offer wide possibilities for advanced functionalized bioabsorbable implants. By implementing lattice structures, big implant sizes and mechanically optimized implant geometries can be achieved enabling full bone replacement or large-scale plate systems, e.g. for orthopedic applications. As shape optimization and lattice structuring of such scaffolds consequently lead to enlarged surface, suitable design and postprocessing routines come into focus. The presented study addresses these new and relevant topics for the first time by evaluating geometry as well as heat and surface treatment options as input parameters for improved chemical and mechanical stability. The outcome of these variations is measured by degradation tests and mechanical analysis. Evaluating these methods, a significant contribution to the development of absorbable magnesium scaffolds is made. The findings can help to better understand the interdependence of high surface to volume ratio Magnesium implants and to deliver methods to incorporate such lattice structures into future large-scale implant applications manufactured from bioabsorbable Magnesium alloys.