Sensitivity of Intervertebral Disc Finite Element Models to Internal Geometric and Non-geometric Parameters

Finite element models are useful for investigating internal intervertebral disc (IVD) behaviours without using disruptive experimental techniques. Simplified geometries are commonly used to reduce computational time or because internal geometries cannot be acquired from CT scans. This study aimed to (1) investigate the effect of altered geometries both at endplates and the nucleus-anulus boundary on model response, and (2) to investigate model sensitivity to material and geometric inputs, and different modelling approaches (graduated or consistent fibre bundle angles and glued or cohesive inter-lamellar contact). Six models were developed from 9.4 T MRIs of bovine IVDs. Models had two variations of endplate geometry (a simple curved profile from the centre of the disc to the periphery, and precise geometry segmented from MRIs), and three variations of NP-AF boundary (linear, curved, and segmented). Models were subjected to axial compressive loading (to 0.86 mm at a strain rate of 0.1/s) and the effect on stiffness and strain distributions, and the sensitivity to modelling approaches was investigated. The model with the most complex geometry (segmented endplates, curved NP-AF boundary) was 3.1 times stiffer than the model with the simplest geometry (curved endplates, linear NP-AF boundary), although this difference may be exaggerated since segmenting the endplates in the complex geometry models resulted in a shorter average disc height. Peak strains were close to the endplates at locations of high curvature in the segmented endplate models which were not captured in the curved endplate models. Differences were also seen in sensitivity to material properties, graduated fibre angles, cohesive rather than glued inter-lamellar contact, and NP:AF ratios. These results show that FE modellers must take care to ensure geometries are realistic so that load is distributed and passes through IVDs accurately.

The Effect of Degeneration on Internal Strains and the Mechanism of Failure in Human Intervertebral Discs Analyzed Using Digital Volume Correlation (DVC) and Ultra-High Field MRI

The intervertebral disc (IVD) plays a main role in absorbing and transmitting loads within the spinal column. Degeneration alters the structural integrity of the IVDs and causes pain, especially in the lumbar region. The objective of this study was to investigate non-invasively the effect of degeneration on human 3D lumbar IVD strains (n = 8) and the mechanism of spinal failure (n = 10) under pure axial compression using digital volume correlation (DVC) and 9.4 Tesla magnetic resonance imaging (MRI). Degenerate IVDs had higher (p < 0.05) axial strains (58% higher), maximum 3D compressive strains (43% higher), and maximum 3D shear strains (41% higher), in comparison to the non-degenerate IVDs, particularly in the lateral and posterior annulus. In both degenerate and non-degenerate IVDs, peak tensile and shear strains were observed close to the endplates. Inward bulging of the inner annulus was observed in all degenerate IVDs causing an increase in the AF compressive, tensile, and shear strains at the site of inward bulge, which may predispose it to circumferential tears (delamination). The endplate is the spine's “weak link” in pure axial compression, and the mechanism of human vertebral fracture is associated with disc degeneration. In non-degenerate IVDs the locations of failure were close to the endplate centroid, whereas in degenerate IVDs they were in peripheral regions. These findings advance the state of knowledge on mechanical changes during degeneration of the IVD, which help reduce the risk of injury, optimize treatments, and improve spinal implant designs. Additionally, these new data can be used to validate computational models.

Predicting meniscal tear stability across knee-joint flexion using finite-element analysis

PURPOSE

To analyse the stress distribution through longitudinal and radial meniscal tears in three tear locations in weight-bearing conditions and use it to ascertain the impact of tear location and type on the potential for healing of meniscal tears.

METHODS

Subject-specific finite-element models of a healthy knee under static loading at 0°, 20°, and 30° knee flexion were developed from unloaded magnetic resonance images and weight-bearing, contrast-enhanced computed tomography images. Simulations were then run after introducing tears into the anterior, posterior, and midsections of the menisci.

RESULTS

Absolute differences between the displacements of anterior and posterior segments modelled in the intact state and those quantified from in vivo weight-bearing images were less than 0.5 mm. There were tear-location-dependent differences between hoop stress distributions along the inner and outer surfaces of longitudinal tears; the longitudinal tear surfaces were compressed together to the greatest degree in the lateral meniscus and were most consistently in compression on the midsections of both menisci. Radial tears resulted in an increase in stress at the tear apex and in a consistent small compression of the tear surfaces throughout the flexion range when in the posterior segment of the lateral meniscus.

CONCLUSIONS

Both the type of meniscal tear and its location within the meniscus influenced the stresses on the tear surfaces under weight bearing. Results agree with clinical observations and suggest reasons for the inverse correlation between longitudinal tear length and healing, the inferior healing ability of medial compared with lateral menisci, and the superior healing ability of radial tears in the posterior segment of the lateral meniscus compared with other radial tears. This study has shown that meniscal tear location in addition to type likely plays a crucial role in dictating the success of non-operative treatment of the menisci. This may be used in decision making regarding conservative or surgical management.

Femoral fracture type can be predicted from femoral structure: A finite element study validated by digital volume correlation experiments

Proximal femoral fractures can be categorized into two main types: Neck and intertrochanteric fractures accounting for 53% and 43% of all proximal femoral fractures, respectively. The possibility to predict the type of fracture a specific patient is predisposed to would allow drug and exercise therapies, hip protector design, and prophylactic surgery to be better targeted for this patient rendering fracture preventing strategies more effective. This study hypothesized that the type of fracture is closely related to the patient-specific femoral structure and predictable by finite element (FE) methods. Fourteen femora were DXA scanned, CT scanned, and mechanically tested to fracture. FE-predicted fracture patterns were compared to experimentally observed fracture patterns. Measurements of strain patterns to explain neck and intertrochanteric fracture patterns were performed using a digital volume correlation (DVC) technique and compared to FE-predicted strains and experimentally observed fracture patterns. Although loaded identically, the femora exhibited different fracture types (six neck and eight intertrochanteric fractures). CT-based FE models matched the experimental observations well (86%) demonstrating that the fracture type can be predicted. DVC-measured and FE-predicted strains showed obvious consistency. Neither DXA-based BMD nor any morphologic characteristics such as neck diameter, femoral neck length, or neck shaft angle were associated with fracture type. In conclusion, patient-specific femoral structure correlates with fracture type and FE analyses were able to predict these fracture types. Also, the demonstration of FE and DVC as metrics of the strains in bones may be of substantial clinical value, informing treatment strategies and device selection and design. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:993-1001, 2018.

Variable bone mineral density reductions post-unicompartmental knee arthroplasty

PURPOSE

Radiolucencies are commonly observed in unicompartmental knee arthroplasty (UKA) patients within 1 year of arthroplasty. The objective of the study was to identify how the bone mineral density (BMD) changes up to 1 year post-arthroplasty.

METHODS

Dual X-ray absorptiometry scans were obtained from 11 UKA patients at 10 days and 3, 6, and 12 months post-surgery. Patients were scanned in both anteroposterior and lateral knee orientations.

RESULTS

Most subjects saw a large decline in BMD in the first 6 months following surgery, followed by some recovery in bone mass. The biggest change occurred under the tibial intercondylar eminence, which decreased significantly by an average of 18 % at 6 months and was 15 % at 1 year. The average bone loss under the tibial tray was low; however, the bone loss at the anterior portion was higher with a significant average decrease of 14 %. There was no change in BMD under the tibial keel. There was significant bone loss of 13 % under the femoral component; the regions anterior and posterior to the central femoral implant peg both had significant bone loss of 14 %. The bone response between patients was very variable, with some patients losing bone steadily, and others gaining it rapidly after an early fall.

CONCLUSIONS

While the overall reduction in BMD under both components was low, it was significant and there was substantial individual variation superimposed on this. Improving our understanding of this response to surgery may impact on prosthesis survival.

LEVEL OF EVIDENCE

Therapeutic study: case series with no comparison group, Level IV.

Validation of multiple subject-specific finite element models of unicompartmental knee replacement

Accurate computer modelling of the fixation of unicompartmental knee replacements (UKRs) is a valuable design tool. However, models must be validated with in vitro mechanical tests to have confidence in the results. Ten fresh-frozen cadaveric knees with differing bone densities were CT-scanned to obtain geometry and bone density data, then implanted with cementless medial Oxford UKRs by an orthopaedic surgeon. Five strain gauge rosettes were attached to the tibia and femur of each knee and the bone constructs were mechanically tested. They were re-tested following implanting the cemented versions of the implants. Finite element models of four UKR tibiae and femora were developed. Sensitivity assessments and convergence studies were conducted to optimise modelling parameters. The cemented UKR pooled R(2) values for predicted versus measured bone strains were 0.85 and 0.92 for the tibia and femur respectively. The cementless UKR pooled R(2) values were slightly lower at 0.62 and 0.73 which may have been due to the irregularity of bone resections. The correlation of the results was attributed partly to the improved material property prediction method used in this project. This study is the first to validate multiple UKR tibiae and femora for bone strain across a range of specimen bone densities.

An optimised method for quantifying glenoid orientation

A robust quantification method is essential for inter-subject glenoid comparison and planning of total shoulder arthroplasty. This study compared various scapular and glenoid axes with each other in order to optimally define the most appropriate method of quantifying glenoid version and inclination.Six glenoid and eight scapular axes were defined and quantified from identifiable landmarks of twenty-one scapular image scans. Pathology independency and insensitivity of each axis to inter-subject morphological variation within its region was tested. Glenoid version and inclination were calculated using the best axes from the two regions.The best glenoid axis was the normal to a least-square plane fit on the glenoid rim, directed approximately medio-laterally. The best scapular axis was the normal to a plane formed by the spine root and lateral border ridge. Glenoid inclination was 15.7 degrees +/- 5.1 degrees superiorly and version was 4.9 degrees +/- 6.1 degrees , retroversion.The choice of axes in the present technique makes it insensitive to pathology and scapular morphological variabilities. Its application would effectively improve inter-subject glenoid version comparison, surgical planning and design of prostheses for shoulder arthroplasty.

Analysis of bone-prosthesis interface micromotion for cementless tibial prosthesis fixation and the influence of loading conditions

A lack of initial stability of the fixation is associated with aseptic loosening of the tibial components of cementless knee prostheses. With sufficient stability after surgery, minimal relative motion between the prosthesis and bone interfaces allows osseointegation to occur thereby providing a strong prosthesis-to-bone biological attachment. Finite element modelling was used to investigate the bone-prosthesis interface micromotion and the relative risk of aseptic loosening. It was anticipated that by prescribing different joint loads representing gait and other activities, and the consideration of varying tibial-femoral contact points during knee flexion, it would influence the computational prediction of the interface micromotion. In this study, three-dimensional finite element models were set up with applied loads representing walking and stair climbing, and the relative micromotions were predicted. These results were correlated to in-vitro measurements and to the results of prior retrieval studies. Two load conditions, (i) a generic vertical joint load of 3 x body weight with 70%/30%M/L load share and antero-posterior/medial-lateral shear forces, acted at the centres of the medial and lateral compartments of the tibial tray, and (ii) a peak vertical joint load at 25% of the stair climbing cycle with corresponding antero-posterior shear force applied at the tibial-femoral contact points of the specific knee flexion angle, were found to generate interface micromotion responses which corresponded to in-vivo observations. The study also found that different loads altered the interface micromotion predicted, so caution is needed when comparing the fixation performance of various reported cementless tibial prosthetic designs if each design was evaluated with a different loading condition.

A numerical tool for the reconstruction of the physiological kinematics of the glenohumeral joint

The aim of this study was to develop and test a robust approach to apply a joint coordinate system (JCS) to imaging data sets of the glenohumeral joint and to reconstruct the kinematics with six degrees of freedom (6DOF) in order to investigate shoulder pathologies related to instability. Visible human data were used to reconstruct bony morphology. Landmarks were used to define axes for body-fixed Cartesian coordinate frames on the humerus and scapula. These were applied to a three-cylinder open-chain JCS upon which the humeral 6DOF motions relative to the scapula were implemented. Software was written that applies 6DOF input variables to rotate and translate the nodes of the surface geometry of the humerus relative to the scapula in a global coordinate frame. The instantaneous relative position and orientation of the humerus for a given set of variables were thus reconstructed on the bone models for graphical display. This tool can be used for graphical animation of shoulder kinematics, demonstrating clinical assessments, and allowing further analysis of the function of tissues within the joint.

Primary stability in reversed-anatomy glenoid components

Reversed-anatomy shoulder replacement is advocated for patients with poor rotator cuff condition, for whom an anatomical reconstruction would provide little or no stability. Modern generations of this concept appear to be performing well in the short-term to midterm clinical follow-up. These designs are almost always non-cemented, requiring a high degree of primary stability to encourage bone on-growth and so to establish long-term fixation. Six different inverse-anatomy glenoid implants, currently on the market and encompassing a broad range of geometrical differences, were compared on the basis of their ability to impart primary stability through the minimization of interface micromotions. Fixing screws were only included in the supero-inferior direction in appropriate implants and were always inclined at the steepest available angle possible during surgery (up to a maximum of 30°). The extent of predicted bony on-growth was, of course, highly dependent on the threshold for interface micromotion. In some instances an additional 30 per cent of the interface was predicted to promote bone on-growth when the threshold was raised from 20 μm to 50 μm. With maximum thresholds of micromotion for bone on-growth set to 30 μm, the Zimmer Anatomical device was found to be the most stable of the series of the six designs tested herein, achieving an additional 3 per cent (by surface area) of bone on-growth above the closest peer product (Biomet Verso). When this threshold was raised to 50 μm, the Biomet Verso design was most stable (3 per cent above the second-most stable design, the Zimmer Anatomical). Peak micromotions were not a good indicator of the predicted area of bone on-growth and could lead to some misinterpretation of the implant's overall performance. All but one of the implants tested herein provided primary stability sufficient to resist motions in excess of 150 μm at the interface.

Fixation of the reversed shoulder prosthesis

The last decade has seen an increased interest in reversed shoulder prostheses. Success rates with these designs have been varied, with initial performance marred by failures resulting from improper implant alignment and an emerging engineering understanding. Competitor products to the well-documented Grammont design have yielded increasingly high success rates. Understanding the relationships between implant design, surgical procedure, and clinical outcome is important so that current results can be improved upon. This study considers the performance of 3 different reversed shoulder designs from the perspective of osseointegration, with the results broadly validated through comparison with experimental data. Finite element modeling was used to clarify the relationships between lateral offset of the center of rotation, screw insertion angle, screw length, screw diameter, bone material quality, and the potential for interdigitation of the supporting bone onto the reversed prosthesis. The results indicate that screw length, insertion angle, and diameter, when maximized, allow the least relative motion between the implant and underlying bone. When the bone is stiffer, the relative motion of the implant is lower. In almost all scenarios modeled, the interface micromotion was small enough to suggest that the glenoid was stable enough to encourage bone ingrowth across the majority of the bone-implant interfaces.

A scapular coordinate frame for clinical and kinematic analyses

The aim of this study was to define a body-fixed coordinate frame for the scapula that minimises axes variability and is closely related to the clinical frame of reference. Medical images of 21 scapulae were used to quantify 14 different axes from identifiable landmarks. The plane of the blade of the scapula was defined. The orientations of the quantified axes were calculated. The angular relationships between axes were quantified and applied to grade the sensitivity of each axis to inter-scapular variations in the others. The volume of data required to define an axis was noted for its dependency on pathology and the three criteria were weighted according to relative importance. The two axes with the highest weighting were applied to define a body-fixed Cartesian coordinate frame for the scapula. A least square medio-lateral line through the centre of the spine root was the most optimal axis. The plane formed by the spine root line and a least square line through the centre of the lateral border ridge was the most optimal scapular plane. This body-fixed Cartesian coordinate frame is closely aligned to the cardinal planes in the anatomical position and thus is a clinically applicable, specimen invariant coordinate frame that can be used in patient-specific kinematics modelling.

Definition of the capsular insertion plane on the proximal humerus

The aim of this work was quantitatively to establish the relationship between the plane that hosts the humeral head lateral margin (anatomical neck) and that of the capsular insertion. Eight cadaveric shoulders were used. These were dissected, exposing the humeral head margin and the root of the capsular humeral insertion to extract digitally their outlines using a mechanical 3-d digitizer. The datasets of the digitized outlines were applied and the geometric planes they best fitted mathematically calculated. Vector analysis techniques were finally applied to the two planes to quantify the relationship between them. The humeral head margin is circular (+/- 2.2% of radius), having each of its outlining points on the same plane (within +/- 1.5 mm.) The capsular attachment outlining points also insert on a plane (+/- 1.4 mm). The two planes are related to one another by an inclination of 14.5 +/- 3.6 degrees. The relationship described here would allow for in vivo prediction of humeral attachment of capsular structures by using radiological datasets of the anatomical neck. This would be useful in patient-specific modelling to study and understand the glenohumeral ligament kinematics during clinical examinations and to plan surgical reconstructive procedures.

Loss of rotator cuff tendon-to-bone interface pressure after reattachment using a suture anchor

The purpose of this study was to examine the tendon-to-bone interface pressure, contact area, and force after reattaching a tendon to bone by use of a suture and suture anchor. Repairs were made in 8 ovine shoulders in vitro, by use of 3 suture types in each: Ethibond, polydioxanone, or Orthocord. A Tekscan pressure sensor was placed between the tendon and bone and monitored for 1 hour after the repair. The principal finding was a significant loss of approximately 60% of the contact parameters immediately after the suture was tied, followed by further significant loss over the next hour to a mean of only 14% of the initial readings. We concluded that pressure measurement systems that only record the initial maximum pressure would yield overly optimistic results for the actual repair pressure after the repair is completed. The Tekscan system, however, allowed us to monitor pressure reductions that occurred both during and after the repair.

Glenohumeral kinematics following total shoulder arthroplasty: a finite element investigation

The osseous geometry of the glenohumeral joint is naturally nonconforming and minimally constrained, and the joint's stability is maintained by action of the rotator cuff muscles. Damage to these muscles is often associated with joint degeneration, and a variety of glenoid prostheses have been developed to impart varying degrees of stability postoperatively. The issues of conformity and constraint within the artificial shoulder have been addressed through in vivo and in vitro studies, although few computational models have been presented. The current investigation presents the results of three-dimensional finite element analyses of the total shoulder joint and the effects of design parameters upon glenohumeral interaction. Conformity was shown not to influence the loads required to destabilize the joint, although it was the principal factor determining the magnitude of humeral head translation. Constraint was found to correlate linearly with the forces required to dislocate the humeral head, with higher constraint leading to slightly greater humeral migration at the point of joint instability. The model predicts that patients with a dysfunctional supraspinatus would experience frequent eccentric loading of the glenoid, especially in the superior direction, which would likely lead to increased fixation stresses, and hence, a greater chance of loosening. For candidates with an intact rotator cuff, the models developed in this study predict that angular constraints of at least 14 degrees and 6.5 degrees in the superoinferior and anteroposterior axes are required to provide stable unloaded abduction of the humerus, with larger constraints of 18 degrees and 10 degrees necessitated by a dysfunctional supraspinatus. The tools developed during this study can be used to determine the capacity for different implant designs to provide resistance to excessive glenohumeral translations and reduce the potential for instability of the joint, allowing surgeons to optimize postoperative functional gains on a patient by patient basis.

Development of a 95/5 poly(L-lactide-co-glycolide)/hydroxylapatite and β-tricalcium phosphate scaffold as bone replacement material via selective laser sintering

95/5 Poly(L-lactide-co-glycolide) was investigated for the role of a porous scaffold, using the selective laser sintering (SLS) fabrication process, with powder sizes of 50-125 and 125-250 microm. SLS parameters of laser power, laser scan speed, and part bed temperature were altered and the degree of sintering was assessed by scanning electron microscope. Composites of the 125-250 microm polymer with either hydroxylapatite or hydroxylapatite/beta-tricalcium phosphate (CAMCERAM II were sintered, and SLS settings using 40 wt % CAMCERAM II were optimized for further tests. Polymer thermal degradation during processing led to a reduction in number and weight averaged molecular weight of 9% and 12%, respectively. Compression tests using the optimized composite sintering parameters gave a Young's modulus, yield strength, and strain at 1% strain offset of 0.13 +/- 0.03 GPa, 12.06 +/- 2.53 MPa, and 11.39 +/- 2.60%, respectively. Porosity was found to be 46.5 +/- 1.39%. CT data was used to create an SLS model of a human fourth middle phalanx and a block with designed porosity was fabricated to illustrate the process capabilities. The results have shown that this composite and fabrication method has potential in the fabrication of porous scaffolds for bone tissue engineering.

Wear in the Prosthetic Shoulder: Association With Design Parameters

Total replacement of the glenohumeral joint provides an effective means for treating a variety of pathologies of the shoulder. However, several studies indicate that the procedure has not yet been entirely optimized. Loosening of the glenoid component remains the most likely cause of implant failure, and generally this is believed to stem from either mechanical failure of the fixation in response to high tensile stresses, or through osteolysis of the surrounding bone stock in response to particulate wear debris. Many computational studies have considered the potential for the former, although only few have attempted to tackle the latter. Using finite-element analysis an investigation, taking into account contact pressures as well as glenohumeral kinematics, has thus been conducted, to assess the potential for polyethylene wear within the artificial shoulder. The relationships between three different aspects of glenohumeral design and the potential for wear have been considered, these being conformity, polyethylene thickness, and fixation type. The results of the current study indicate that the use of conforming designs are likely to produce slightly elevated amounts of wear debris particles when compared with less conforming joints, but that the latter would be more likely to cause material failure of the polyethylene. The volume of wear debris predicted was highly influenced by the rate of loading, however qualitatively it was found that wear predictions were not influenced by the use of different polyethylene thicknesses nor fixation type while the depth of wearing was. With the thinnest polyethylene designs (2mm) the maximum depth of the wear scar was seen to be upwards of 20% higher with a metal-backed fixation as opposed to a cemented design. In all-polyethylene designs peak polymethyl methacrylate tensile stresses were seen to reduce with increasing polyethylene thickness. Irrespective of the rate of loading of the shoulder joint, the current study indicates that it is possible to optimize glenoid component design against abrasive wear through the use of high conformity designs, possessing a polyethylene thickness of at least 6mm.

Finite element modelling of glenohumeral kinematics following total shoulder arthroplasty

Due to the shallowness of the glenohumeral joint, a challenging but essential requirement of a glenohumeral prosthesis is the prevention of joint dislocation. Weak glenoid bone stock and frequent dysfunction of the rotator cuff, both of which are common with rheumatoid arthritis, make it particularly difficult to achieve this design goal. Although a variety of prosthetic designs are commercially available only a few experimental studies have investigated the kinematics and dislocation characteristics of design variations. Analytical or numerical methods, which are predictive and more cost-effective, are, apart from simple rigid-body analyses, non-existent. The current investigation presents the results of a finite element analysis of the kinematics of a total shoulder joint validated using recently published experimental data for the same prostheses. The finite element model determined the loading required to dislocate the humeral head, and the corresponding translations, to within 4% of the experimental data. The finite element method compared dramatically better to the experimental data (mean difference=2.9%) than did rigid-body predictions (mean difference=37%). The goal of this study was to develop an accurate method that in future studies can be used for further investigations of the effect of design parameters on dislocation, particularly in the case of a dysfunctional rotator cuff. Inherently, the method also evaluates the glenoid fixation stresses in the relatively weak glenoid bone stock. Hence, design characteristics can be simultaneously optimised against dislocation as well as glenoid loosening.

Finite element models of total shoulder replacement: application of boundary conditions

The widespread use of FEA within orthopaedics is often prohibited by the limits of available computational power, with simplifications to the model often necessary in order to permit solution. An example of this includes the use of osseous models that exclude muscular loading, and may consist of only a partial or truncated region of the anatomy. However, is it possible to make such simplifications without affecting the predictive quality of the model? This issue has been considered using the specific example of the total shoulder reconstruction, where the effects of including the entire osseous region and/or the muscle loadings, has been evaluated. The effect of including the muscle loadings and the entire osseous structure was seen to increase with distance from the articular surface of the glenoid prosthesis. Stresses in the cement mantle were reduced in the absence of either the entire scapula bone or the muscle loading. The study suggests that the use of a fully defined scapula (hard- and soft-tissue) is particularly important when investigating fixation, whilst less comprehensive models should be appropriate for studies of the prosthesis exclusively.

Basic fibroblast growth factor mediates transduction of mechanical signals when articular cartilage is loaded

OBJECTIVE

To determine whether the basic fibroblast growth factor (bFGF) mediates signal transduction in articular cartilage in response to mechanical loading.

METHODS

Articular cartilage from porcine metacarpophalangeal or knee joints was cyclically loaded (62.5-250N) for 2 minutes in the absence or presence of a bFGF receptor inhibitor, SB 402451 (250 nM). Activation of the extracellularly regulated kinase MAP kinase ERK was measured by Western blot analysis. Changes in protein synthesis were assessed by measuring the incorporation of (35)S-Met/Cys into proteins secreted by cartilage explants or by isolated chondrocytes.

RESULTS

Rapid activation of the ERK MAP kinase occurred when articular cartilage was loaded. This was dependent upon release of the bFGF because it was restricted by the FGF receptor inhibitor. Loaded explants were shown to release bFGF. Loading or bFGF stimulation of explants induced synthesis and secretion of tissue inhibitor of metalloproteinases 1 (TIMP-1), which was inhibited by SB 402451.

CONCLUSION

Cyclical loading of articular cartilage causes bFGF-dependent activation of ERK and synthesis of TIMP-1.

The effects of glenoid component alignment variations on cement mantle stresses in total shoulder arthroplasty

Loosening of the glenoid component has been cited as the most frequent cause of patient dissatisfaction with total shoulder arthroplasty, and it has been demonstrated in clinical studies that misalignment of the prostheses can be a causative factor. Finite element analyses of five different glenoid component alignments (central, anteverted, retroverted, inferiorly inclined, and superiorly inclined) were conducted in order to predict changes in the survivability of the cement mantle surrounding the glenoid component. The potential for mechanical failure of the mantle in the centrally aligned implant, during unloaded abduction, was seen to be lower than for any other alignment. Normal bone outperformed simulated rheumatoid models in all cases. Retroversion was worse than anteversion, and superoinferior misalignment was worse than anteroposterior. The quality of the supporting bone stock was found to be particularly significant to cement survivability, more so than the occurrence of eccentric loading of the joint. Shear forces acting on the glenoid component were found to be more detrimental than axial forces, resulting in a greater likelihood of failure toward the extremes of motion. The study suggests that significant efforts should be made to align the glenoid component correctly and also to ensure suitably consistent support of the prosthesis within the bone.