Characterization of cavitation-radiated acoustic power using diffraction correction

A method is developed for compensating absolute pressure measurements made by a calibrated passive cavitation detector (PCD) to estimate the average acoustic power radiated from a region of interest (ROI) defined to encompass all cavitating bubbles. A diffraction correction factor for conversion of PCD-measured pressures to cavitation-radiated acoustic power per unit area or volume is derived as a simple analytic expression, accounting for position- and frequency-dependent PCD sensitivity. This approach can be applied to measurements made by any PCD without precise knowledge of the number, spatial, or temporal distribution of cavitating bubbles. The diffraction correction factor is validated in simulation for a wide range of ROI dimensions and frequencies. The correction factor is also applied to emission measurements obtained during in vitro ultrasound-enhanced sonophoresis experiments, allowing comparison of stable cavitation levels between therapeutic configurations with different source center frequencies. Results incorporating sonication at both 0.41 and 2.0 MHz indicate that increases in skin permeability correlate strongly with the acoustic power of subharmonic emissions radiated per unit skin area.

A Novel, Optimized Method to Accelerate the Preparation of Injectable Poly-L-Lactic Acid by Sonication

Current consensus for preparing injectable poly-L-lactic acid (PLLA) suggests adequate hydration (less than equal to 2-24 hours of reconstitution) of the lyophilized particles before injection, but the volume of reconstitution and the duration of hydration time varies. This study established a method to evaluate the distribution of PLLA particles after hydration and found that longer hydration time increased the effective portion (particles less than 60 μm) of PLLA products. Further investigation of the feasibility of reconstitution with sonication revealed that 2-hour hydration of PLLA powders with additional 5-minute-sonication could yield a comparable particle distribution with 48-hour-hydration of PLLA. Moreover, adding lidocaine into the diluent did not alter the distribution of PLLA particles. We proposed a new, feasible and efficient method of preparing PLLA injectable products: 2-hour hydration of the powders, sonication of the bottle or vial containing PLLA products for at least 5 minutes, and finalization with 1-2 mL of lidocaine immediately before injection. J Drugs Dermatol. 2018;17(8):894-898.

Methodology on quantification of sonication duration for safe application of MR guided focused ultrasound for liver tumour ablation

BACKGROUND AND OBJECTIVE

Magnetic Resonance Guided Focused Ultrasound (MRgFUS) for liver tumour ablation is a challenging task due to motion caused by breathing and occlusion due the ribcage between the transducer and the tumour. To overcome these challenges, a novel system for liver tumour ablation during free breathing has been designed.

METHODS

The novel TRANS-FUSIMO Treatment System (TTS, EUFP7) interacts with a Magnetic Resonance (MR) scanner and a focused ultrasound transducer to sonicate to a moving target in liver. To meet the requirements of ISO 13485; a quality management system for medical device design, the system needs to be tested for certain process parameters. The duration of sonication and, the delay after the sonication button is activated, are among the parameters that need to be quantified for efficient and safe ablation of tumour tissue. A novel methodology is developed to quantify these process parameters. A computerised scope is programmed in LabVIEW to collect data via hydrophone; where the coordinates of fiber-optic sensor assembly was fed into the TRANS-FUSIMO treatment software via Magnetic Resonance Imaging (MRI) to sonicate to the tip of the sensor, which is synchronised with the clock of the scope, embedded in a degassed water tank via sensor assembly holder. The sonications were executed for 50 W, 100 W, 150 W for 10 s to quantify the actual sonication duration and the delay after the emergency stop by two independent operators for thirty times. The deviation of the system from the predefined specs was calculated. Student's-T test was used to investigate the user dependency.

RESULTS

The duration of sonication and the delay after the sonication were quantified successfully with the developed method. TTS can sonicate with a maximum deviation of 0.16 s (Std 0.32) from the planned duration and with a delay of 14 ms (Std 0.14) for the emergency stop. Student's T tests indicate that the results do not depend on operators (p > .05).

CONCLUSION

The evidence obtained via this protocol is crucial for translation- of-research into the clinics for safe application of MRgFUS. The developed protocol could be used for system maintenance in compliance with quality systems in clinics for daily quality assurance routines.

Evaluation of relative importance of ultrasound reactor parameters for the removal of estrogen hormones in water

The growing interest in sonochemistry as a tool for environmental remediation leads to the need for process optimization. Sonochemistry is a complex process, which depends on physical parameters and also on the process conditions. Physical parameters are interrelated and therefore a systematic approach has to be taken to optimize the process. The effect of physical parameters on the destruction of seven estrogen hormones (17α-estradiol, 17β-estradiol, estriol, 17α-ethinylestradiol, 17α-dihydroequilin, estrone and equilin) is reported in this study. Artificial neural networks (ANN) was used as a tool to identify the correlations between these process parameters. ANN enabled the establishment of relationship between sonication parameters such as power density, power intensity, ultrasound amplitude, as well as the reactor design parameters. The major significance was attributed to the area-specific power density and the volume-specific power intensity. The results of this work provide a sound basis to design pilot and full-scale ultrasound treatment systems. Process optimization lead to a 5-fold decrease in energy consumption as compared to the commercially available reactors, thereby making the process attractive for field applications.

Characterisation and improvement of a reference cylindrical sonoreactor

This paper describes theoretical and experimental methods for characterising the performance of a 25 kHz sonochemical reactor (RV-25), which is being developed as a reference facility for studying acoustic cavitation at the National Physical Laboratory (NPL). Field measurements, acquired in different locations inside the sonoreactor, are compared with finite element models at different temperatures, showing that relatively small temperature variations can result in significant changes in the acoustic pressure distribution (and consequent cavitation activity). To improve stability, a deeper insight into the way energy is transferred from the power supply to the acoustic field is presented, leading to criteria - based on modal analysis - to dimension and verify an effective temperature control loop. The simultaneous use of measurements and modelling in this work produced guidelines for the design of multi-frequency cylindrical sonoreactors, also described.

Calibration of the 1-MHz Sonitron ultrasound system

Successful drug and gene delivery across cellular membranes can lead to improved therapeutic outcomes. Recent studies have suggested that sonoporation may enhance drug and gene delivery across cellular membranes. The enhancement may be a result of transient permeation of the membrane from cavitation or microstreaming effects of microbubbles exposed to ultrasound. Given limited acoustic pressure calibration and beam profile characterization of the Sonitron ultrasound systems in cellular bioeffects studies previously published, the objective of this work was to calibrate the acoustic output and explore the potential for standing waves in a cell-well plate. In this study, three 1-MHz transducers driven by Sonitron ultrasound systems, which have been used in a number of sonoporation studies, were calibrated. Transducers with 10-mm, 6-mm and 20-mm-diameter apertures (Sonitron 1000 and 2000, Rich-Mar, Inola, OK, USA) were calibrated using polyvinylidene fluoride (PVDF) needle hydrophones. Axial and transverse beam profiles were obtained, and the pressures were measured as a function of Sonitron intensity dial setting and duty cycle. The acoustic intensity was calculated and compared with the Sonitron intensity dial setting for duty cycles from 10-100%. Standing waves caused by reflections from the hydrophone holder were detected for each transducer. This observation may also have implications for in vitro sonoporation studies. Acoustic field characterization is an important first step in understanding the mechanisms of sonoporation and drug delivery across biomembranes.

Toward a reference ultrasonic cavitation vessel: Part 2--investigating the spatial variation and acoustic pressure threshold of inertial cavitation in a 25 kHz ultrasound field

As part of an ongoing project to establish a reference facility for acoustic cavitation at the National Physical Laboratory (NPL), carefully controlled studies on a 25 kHz, 1.8 kW cylindrical vessel are described. Using a patented high-frequency acoustic emission detection method and a sonar hydrophone, results are presented of the spatial variation of inertial acoustic cavitation with increasing peak-negative pressure. Results show that at low operating levels, inertial acoustic cavitation is restricted to, and is strongly localized on, the vessel axis. At intermediate power settings, inertial acoustic cavitation also occurs close to the vessel walls, and at higher settings, a complex spatial variation is seen that is not apparent in measurements of the 25 kHz driving field alone. At selected vessel locations, a systematic investigation of the inertial cavitation threshold is described. This was carried out by making simultaneous measurements of the peak-negative pressures leading to inertial cavitation and the resultant MHz-frequency emissions, and indicates an inertial cavitation threshold of 101 kPa +/- 14% (estimated expanded uncertainty). However, an intermediate threshold at 84 kPa +/- 14% (estimated expanded uncertainty) is also seen. The results are discussed alongside theoretical predictions and recent experimental findings.